User`s Manual
Contents
1. INSTRUCTION MANUAL 5 step Reverse the Door Handle ig Remove the gasket at the right inner side of the door to expose the 2 decoration screws 0 18 Unscrew them in a clockwise direction with a straight screwdriver at first and then loosen them in a counter clockwise direction by fingers from the outer side of the door Now the screw holes are ready for installing the handle to the right side See Figure 10 Remove the gasket at the left inner side of the door to expose the 2 handle screws 0 19 Unscrew them in a counter clockwise direction with a cross screwdriver take out the screws and the washers as well as the handle See Figure 11 Install the handle to the outer right side of the door backwards to the steps of taking down the door See Figure 12 Install the 2 decoration screws to the holes at he left side of the outer door backwards to the steps of unscrewing it See Figure 13 Make sure the door gasket is tidy Figure13 a T ne ii p 20 FOR FLOOR STANDING SERIES Remarks INSTRUCTION MANUAL e Reversible door swing function is only available for a unit with control panel inside the cabinet e The instruction is based on a unit with right door hinge installed already e All removed parts must be saved to d2. MANUAL Notice For the first time to use the appliance or to restart the appliance after having been shut off for a long time you may find a few degrees variance between the set temperature and the displayed temperature It is normal and everything of the appliance will be in the order after a few hours running TEMPERATURE DISPLAY WINDOW e The temperature is displayed in digital which is the best way to be read out The digital is shown as the set temperature when you are setting the temperature and it will change to be the real temperature of the inside cabinet after 10 seconds without being touched e When the temperature probe is out of order the display window will show with HH or LL instead of a digital figure while continuous buzz sound will be heard In case of this happens this appliance is considerately designed to keep periodical running of compressor and fans which helps to keep the coldness of the inside cabinet to protect your stored wines Warning To avoid destroying your stored wines it is strongly recommended to have the appliance repaired immediately as the Spare periodical running can not ensure the appliance to achieve the temperature you have set SELECTING FAHRENHEIT F amp CELSIUS C For Single Zone Touch the marks with 2 fingers at the same time and hold for 5 seconds you can interchange the c Fahrenheit F and Celsius display C For Dual Zones Just touch th
3. shelves quantity preinstalled in the Wine Cooler There are two designs for the pull out shelves 1 The shelves are without telescopic rails but with a plastic stopper on each sides of the shelf track to prevent bottles from falling See the right figure 2 The shelves are with telescopic rails which has stoppers by themselves To prevent damaging the door gasket make sure to have the door opened fully all the way before pulling the shelves out Please store wine in sealed bottles Should the wine cooler be left empty for long periods it is suggested that the appliance is unplugged and after careful cleaning leave the door ajar to allow air to circulate inside the cabinet in order to avoid possible condensation mold or odours forming Recommended Temperatures for chilling storage your wines Red Wines 15 18 C Dry White Wines 9 14 C Rose Wines 10 11 C Sparkling Wines 5 8 C 10 INSTRUCTION MANUAL OPERATING CONTROL PANEL DX 7 22BK SK DX 19 58BK SK Power Lighting Display Window Temp Down Lock Unlock 0C 0F Interchange DX 46 146DBK DSK DX 94 270DBK DSK DX 166 428DBK DSK DX 181 490DBK DSK Lock Unlock Temp Up Upper Zone Temp Down Display Window Power Lighting C F Bottom Zone Zone Select Interchange Display Window DX 51 150DBK DSK Lighting Upper Zone Display Temp up Temp Down ase HA HAPO SET DISPLAY
4. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of the appliance Do not connect or disconnect the electric plug when your hands are wet Unplug the appliance or disconnect power before cleaning maintenance or servicing Failure to do so can result in electrical shock or death Do not attempt to repair or replace any part of the appliance unless it is specifically recommended in this material All other servicing should be referred to a qualified technician Ensure enough peoples to move and install the appliance to avoid any damage to the appliance or injury to the peoples To ensure proper ventilation for the appliance the front of the unit must be completely unobstructed Locate the unit away from direct sunlight and sources of heat stove heater radiator etc The fuse or circuit breaker size should be 10 amps or higher It is important for the appliance to be leveled in order to work properly You may adjust the appliance s feet to level it This appliance is not intended for use by young children Never allow children to operate play with or crawl inside the appliance Do not use solvent based cleaning agents of abrasives on the interior These cleaners may damage or discolor the interior Do not use this appliance for other than its intended purpose The use of attachments not recommended by the manufacturer may be hazardous When you dispose the appliance take off the door and le
5. DUNAVOX INSTRUCTION MANUAL COMPRESSOR WINE COOLER This manual contains important information including safety and installation instructions of the appliances Please read it carefully before use and follow all safety information amp instructions It is recommended to keep this manual for easy reference so that you can be familiar with the operation of the appliance CONTENTS IMPORTANESAFET INFORMATION AALANGAN NAAN AA 2 STURCTURE AND INSTALLATION DRAWING ma ANA AA AA AA 3 ACCESSORY INSTALLATION BEFORE OPERATING ca AA 8 OPERATING THE WINE COOLER 22i NA AGANG ANAN OE NAGANA LAAL NANANA NADA 9 CARE AND MAINTENANCE eripi E AA 13 TROUBLESHOOTING Sarera AA AA AAP AA AP AE 15 REVERSE THE DOOR SWING sA AA NANANA AA AA 16 INSTRUCTION MANUAL IMPORTANT SAFETY INFORMATION Before use the appliance please properly position and install it as described in this manual To avoid the risk of fire electrical shock or injury when using the appliance follow these basic precautions The appliance is intended to be used exclusively for the storage of wine Make sure the voltage current marked on the rating label corresponds with your supply voltage Plug into a grounded 3 pin outlet do not remove grounding pin do not use an adapter and do not use an extension cord lt is recommended that a separate circuit serving only your appliance be provided Never clean the appliance parts with flammable fluids which may create a fire hazard or explosion
6. SET DISPLAY Temp Up Temp Down Lower Zone Display Celsius Fahrenheit POWER ON OFF CONTROL e e When the appliance is plugged in to a power outlet it powers on automatically e e Touch the power mark and hold for 10 seconds to turn off or turn on the appliance e No matter it is under a locked or unlocked situation you can turn off the appliance by touching the power mark and holding for 10 seconds 44 Warning To avoid breaking the compressor please do not turn on the appliance again within 5 Minutes after you turn it off 11 INSTRUCTION MANUAL UNLOCKING THE CONTROL PANEL mal ka To unlock the control panel touch the power mark and lighting mark with 2 fingers at the same time and hold for 3 seconds When unlocked a buzz sound will be heard The control panel will be automatically locked with a buzz sound heard after 10 seconds without being touched Under the locked situation the control panel will not react to any touching except the power mark which works as above Power On Off Control description INTERIOR LIGHTING ON OFF CONTROL Under the unlocked situation touch the lighting mark to turn on or turn off the interior cool LED lighting The lighting will be continuously on if it is not turned off TEMPERATURE SETTING For Single Zone The temperature setting range is 5 22 C 41 72 F Directly touch the mark or to set the Wine Cooler temperature as you want Th
7. UAL DX 41 130BBK BSK Installation Drawin 1 Before inserting the unit into the kitchen cabinet please unscrew the original 4 leveling feet in white and screw the 2 short leveling feet in black which are packed as the accessory to the front bottom of the unit 2 Tighten the 2 screws to fix the mounting bar which has been fixed on the bottom of the unit to the kitchen cabinet See below drawing Mounting Bar INSTRUCTION MANUAL FLOOR STANDING SERIES Single Zone Structure 1 OY Upper Right Hinge Touch key Control Panel amp Digital Display et Outside Cabinet ae Handle Front Louver eee Shallow Shelf Leveling Foot Dual Zones Structure Outside Cabinet Handle SSS Touch key Control Panel 8 Digital Display Front Louver SSS Shallow Shelf Leveling Foot Ba ag ACCESSORY INSTALLATION BEFORE OPERATING UNPACKING AND CLEANING THE WINE COOLER e Remove the exterior and interior packing materials e Let the appliance stand upright for approximately 2 hours before connecting it to the power source which helps to reduce the possibility of a cooling system malfunction from handling during transportation e Use a soft cloth to clean the interior surface with lukewarm water e Install the door handle provided with the appliance by following these steps INSTRUCTION MANUAL Remove the gasket at the inner st 1 s
8. ave the shelves in place so that children may not easily climb inside And make sure the coolant circuit particularly the heat exchanger at the back bottom of the unit not be damaged The symbol on the product or its packaging indicates that this product is not to be handled as normal household waste and it is to be taken to a recycling collection point for electrical and electronic goods INSTRUCTION MANUAL STRUCTURE AND INSTALLATION DRAWING The following pictures only show the structure of the appliance as well as the installation drawing The dimension and shelf quantity may differ among the models of the same series BUILT UNDER SERIES Built under a kitchen table top Single Zone Structure Touch key Control Panel amp Digital Display Outside Cabinet Deep Shelf Shallow Shelf Front Louver Leveling Foot Dual Zones Structure Outside Cabinet Touch key Control Panel amp Digital Display Handle Deep Shelf Shallow Shelf Front kak Gasket Leveling Foot DX 7 22BK SK Installation Drawing mm INSTRUCTION MANUAL DX 19 58BK SK Installation Dra
9. e first touch on mark or will recall the previous set temperature displayed in the digital window If the appliance runs after a power failure or unplugging the previous set temperature does not exist and is replaced by the default temperature at 12 C Touch the mark 4 to increase the set temperature by 1 C On the contrary touch the mark S to decrease the set temperature by 1 C The digital will change to display the real temperature of the inside cabinet after 10 seconds without being touched For Dual Zones The temperature setting ranges are 5 12 C 41 54 F for the upper zone and 12 22 C 54 72 F for the bottom zone You need to select the set zone by touching the mark before touching the mark or to set the wanted temperature The display window with digital flashing indicates the zone ready for temperature setting The first touch on mark or will recall the previous set temperature displayed in the digital window If the appliance runs after a power failure or unplugging the previous set temperature does not exist and is replaced by the default temperature at 10 C for the upper zone while 16 C for the bottom zone Touch the mark to increase the set temperature by 1 C On the contrary touch the mark to decrease the set temperature by 1 C The digital will change to display the real temperature of the inside cabinet after 10 seconds with out being touched 12 INSTRUCTION
10. e mark you can interchange the Fahrenheit F and Celsius C display for both zones at the same time CARE AND MAINTENANCE CLEANING THE WINE COOLER e Turn off the power unplug the appliance and remove all items including shelves e Wipe the inside surfaces with a sponge and baking soda solution The solution should be about 2 tablespoons of baking soda to a quart approx 1 litre of warm water e Wash the shelves with a mild detergent solution Allow wooden shelves to dry before placing back into the wine cooler e Wring excess water out of the sponge or cloth when cleaning area of the controls or any electrical parts e Wipe the outside cabinet with warm water and mild liquid detergent Dry with a clean soft cloth e Do not use steel wool or steel brush on the stainless steel These will contaminate the stainless steel with steel particles and rusting may occur 13 INSTRUCTION MANUAL POWER FAILURE Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times of door opening If the power is going to be off for a longer period of time you need to take the proper steps to protect your contents MOVING THE WINE COOLER e Remove all items e Securely tape down all loose items shelves inside your appliance e Turn the adjustable leg up to the base to avoid damage e Tape the door shut e Be sure the appliance stays secure in the up
11. ht hinge to left hinge you need to get ready 3 new spare parts upper left hinge upper left hinge cover right door corner cover e All removed parts must be saved to do the door reinstallation except those remarked with Disused 1 step Takedown the Door See Figure 1 1 Loosen the 2 screws o 1a with a cross screwdriver and take out the upper right hinge cover Disused There are two wiring harnesses 0 4 amp o 5 with their terminals connected together 2 Disconnect the two wiring harnesses and loosen the 3 screws o 3a to take out the upper right hinge 3 Loosen the 4 screws o 3b amp the 1 screw o 8 to take out the bottom hinge 4 Carefully take the whole door out Figure INSTRUCTION MANUAL 2 step Tidy the Door 1 Pull the harness wires one by one out of the upper right hinge hole through its gap and remove the upper right hinge Disused See Figure 2 2 Tidy the harness and carefully push back it into the door frame and cover it with the right door corner cover o 11 See Figure 3 Figure3 mo Remarks If it is difficult to push back the harness into the door frame please follow the steps in Figure 4 amp 5 1 Remove the gasket at the upper inner side of the door to expose the display back cover 2 Carefully prize up the back cover by a straight screwdriver Then slowly draw the harness into the door frame and tidy the gasket Displa 3 S
12. lotted Figure4 Pagi a _ Screwdriver Figured 5 3 Insert a straight screwdriver to the groove of the left door corner cover 0 12 and prize it up See Figure 6 4 4 Slowly pull out the harness o 13 at the left door corner which must be ensured no longer than 90 mm to avoid loosen the inside terminals Insert the harness wires one by one into the upper left hinge hole through its gap See Figure 7 18 INSTRUCTION MANUAL 3 4 step Tidy the Cabinet See Figure 8 1 Loosen the 2 screws o 1b to take out the harness cover 0 15 from the top left side of the cabinet 2 Install the harness cover at the top right side of the cabinet to cover the harness there 3 Install the bottom hinge at the bottom left side of the cabinet with 4 screws 0 3b Figures 4 step Install the Door See Figure 9 1 Install the upper left hinge o 14 at the top left side of the cabinet with 3 screws o 3a 2 Fix the door to the bottom hinge with a screw 0 8 3 Connect the two wiring harnesses 13 amp 0 17 through their terminals 4 Tidy the harnesses and install the upper left hinge cover 0 16 with the screwo 1a Figure9 16 lt gt 1a K oy ame 3a
13. o the door reinstallation 1 step Prize up the hinge screw holes cover 1 and hinge cover 2 with a straight screwdriver Take out the upper hinge by loosening the screws 3a and lift up the whole door See Figure 1 2 4 step Move the support rod O 6 at the bottom of the door from the right to the left side Move the hinge hole cover at EC the top of the door from the left side to the right side See Figure 2 4 3 Fig 3 step Figure3 Pull out the bottom hinge cover 0 9 and take out the bottom hinge by loosing the screws Loose the 4 screws on the bottom left side Install the bottom hinge to the left side while screw theholes on the right side See Figure 4 21 4 step INSTRUCTION MANUAL To reinstall the door to the opposite side insert the door support rod to the bottom hinge through a washer C_ 11 and screw the upper hinge which has connected with the door Finally cover the hinges as well as the hinge screw holes See Figure 5 amp 6 5 step Figure5 Figu Ve Te Change the door handle from the left to the right side of the front door by following the instructions as mentioned above 22
14. rews and See Figure 1 Carefully remove the door from the upper right hinge and prevent it from scratching Take out the support rod from the door hinge hole See Figure 2 Pull out the 6 decorating plastic bolts covering the reserved hinge screw holes at the front left corner of the cabinet Unscrew the upper right hinge O 4 Disused and bottom left hinge O 6 Disused from the cabinet See Figure 3 Install the upper left hinge O 7and bottom left hinge O 8 to the left side of the cabinet Make sure the screws are tightened See Figure 4 Put upside down the door and install it to the left hinges by following the opposite steps of taking down of the door as described above Cover the hinge screw holes on the right side with the 6 decorating plastic bolts Leveling Foot 16 INSTRUCTION MANUAL FOR BUILT IN COLUMN SERIES For models produced in 2011 only For 2012 model DX 24 56 has right and left hand version non reversible For DX 41 130 the Built under model instruction applies Remarks e Reversible door swing function is only available for a unit with 4 handle screw holes reserved on the front door 2 at the left side and 2 at the left side e The instruction is only suitable for a unit with control panel on the door e The instruction is based on a unit with right door hinge installed already e To reserve the door from rig
15. right position during transportation Also protect outside of appliance with a blanket or similar item ENERGY SAVING TIPS e The appliance should be located away from heat producing appliances and away from direct sunlight e Ensure that the unit is adequately ventilated Never cover air vents e Only open the door when necessary Avoid leaving the door open for long periods or opening closing the door frequently 14 INSTRUCTION MANUAL TROUBLESHOOTING If you feel the appliance is out of order follow these instructions to try to see if you can solve the problem simply by yourself before calling for service PROBLEM POSSIBLE CAUSE MEASURE The Wine Cooler does not operate The Wine Cooler is not cold enough Automatically turn on and turn off frequently The lighting does not work Too much vibration The Wine Cooler seems to make too much noise The door will not close properly The display window is shown with HH or LL instead of a digital figure and or with continuous buzz sound Not plugged in The appliance is turned off The circuit breaker tripped or a blown fuse Check the temperature control setting External environment may require a higher setting The door is opened too frequently The door is not closed completely The door gasket does not seal properly The room temperature is hotter than normal A large amount of contents has been added to the Wine Cooler The door is opened
16. tep side of the door to expose the binabad two screw holes 9nd step Install the handle tightly with the Flat Washer N screws and washers provided d Handle Locker Washer ee gid step Tidy and restore the gasket LOCK amp UNLOCK THE DOOR FOR OPTION e Lock is an optional function If your Wine Cooler has such function a key should be attached inside the packing of this Manual e Insert the key into the lock and turn it counter clockwise to unlock the door To lock it please follow the reversed operation Please save the key well OPERATING THE WINE COOLER WORKING CLIMATE e The appliance is designed for operating from SN to T climate see below climate class chart It is recommended to maintain the ambient around 22 25 C which helps the appliance working with low power consumption e lf the ambient temperature is above or below the designed climate range the performance of the unit may be affected For example the appliance operating in extreme cold or hot conditions may cause interior temperatures to fluctuate and the temperature set 5 22 C may not be reached sometimes Climate Class Ambient Temp SN 10 32 C N 16 32 C ST 18 38 C T 18 43 C INSTRUCTION MANUAL WINE STORAGE The standard shelves are designed perfectly for Bordeaux bottle storage The maximum loaded bottles may vary subject to the different size or dimension of the wine bottles you store as well as the
17. too frequently The door is not closed completely The temperature control is not set correctly The door gasket does not seal properly Not plugged in The circuit breaker tripped or a blown fuse The lighting is turned off Check to assure that the appliance is level Check to assure no parts inside the cabinet or in the compressor chamber are loose The rattling noise may come from the flow of the refrigerant which is normal As each cycle ends you may hear gurgling sounds caused by the flow of refrigerant Contraction and expansion of the inside walls may cause popping and crackling noises The appliance is not level The wine COOLER is not level The door was reversed and not properly installed The gasket is dirty The shelves are out of position The temperature probe is out of order 15 INSTRUCTION MANUAL REVERSE THE DOOR SWING FOR BUITL UNDER SERIES Remarks e Reversible door swing function is only available for a unit with 870 mm height and with control panel inside the cabinet e The instruction is based on a unit with right door hinge installed already e To reserve the door from right hinge to left hinge you need to get ready 2 new spare parts an upper left hinge and a bottom left hinge e All removed parts must be saved to do the door reinstallation except those remarked with Disused 1 step 2 4 step 3 step 4 step 5 step Open the door and loosen the 2 sc
18. wing mm DX 51 150DBK DSK Installation Drawing mm DX 46 145DBK DSK Installation Drawing mm INSTRUCTION MANUAL DX 94 270DBK DSK Installation Drawing mm oe Se DX 166 428DBK DSK Installation Drawing mm DX 181 490DBK DSK Installation Drawing mm baa INSTRUCTION MANUAL BUILT IN COLUMN SERIES Built into a kitchen cabinet DX 24 56BBK BSK Structure Outside Cabinet ee Door Touch Key Control Panel amp Digital Display as Condenser Handle Gasket Leveling Foot iviounting Bar DX 41 130BBK BSK Structure Ouisige Capi _Door Handle Touch key Control Panel oo cgo o e A Gasket Leveling Foot Mounting Ba DX 24 56BBK BSK Installation Drawing 1 Before inserting the unit into the kitchen cabinet please unscrew the original 4 leveling feet in white and screw the 2 short leveling feet in black which are packed as the accessory to the front bottom of 200cm Min s AK ID a the unit EK 29mm 2 Tighten the 2 screws to fix the mounting bar which Bana 4 has been fixed on the bottom of the unit to the kitchen cabinet See below drawing Mounting Bar INSTRUCTION MAN
Download Pdf Manuals
Related Search