User Manual
Contents
1. Note Data are subject to change without notice If you are interested in this product please check with your dealer or our requests for updated information or video2. are connected with the controller 500mm How to fix the panel on the wall 1 Drawing on the wall with 50 50cm size as photo show LED DiscoPanel 3 Fix the cross fixture of led bubble panel on the wall by screw 4 Push the bubble panel on the cross fixture directly and finalize the installation To easy punch and fixed please use flameproof board or PC board as a fixed plate if possible LED Disco Panel Trouble Shooting Listed below are some common problems solutions 1 Product can not receive DMX signal Check the DMX signal cable is properly connected besides check all the wiring is connected to the correct connector especially the input and output connection 2 Product can not receive sound Quiet or sharp sound will not activate the product change another panel if the problem persists please contact your dealer to serve you when it still useless Regular Cleaning Keep this product around no other heat generating items some dust adhesion will be in after using for some time timely clean up is very important Cleaning should be extra carefully when you clean the product and should avoid liquid spilled into the inside of the product Using water or a mild soap and a soft cloth to wipe the exterior of the product avoid using strong base concentrated alcohol or organic solvents The frequency of cleaning for the product depends on the influence of the environment such as smoke fog residue dust dew etc
3. User Manual LED Disco Panel Please read over this manual before using LED Disco Panel Before Installatio Guide In order to optimize the performance of this product please read the following details to be familiar with the basic product operation instruction security matters way of use And maintain Please keep this manual for future reference Product withdrawal Thank you for purchasing the LED DISCO PANEL every tiles of floor have passed the strict factory test please feel free to use it After receiving the goods please firstly inspect them then to sign in If the cartons have damaged check carefully the internal lamps and the parts are intact If not please contact with the manufacturer or your dealer to get further instructions please do not directly reject the goods Brief Introduction LED DISCO PANELis a type of smart lamp which have the Auto and Sound Active mode and also can be controlled by DMX Warning Please do not try to maintain and repair the lamps by yourselves there is no parts to be repaired or A replaced inside the lamp or we will not offer the warranty service If there is damage happens in using process please contact with the manufacturer or your dealer at the first time or do the maintenance and replacement under the guidance of professional Carton lt 3 rr Packing Carton can be recyclable LED Disco Panel Description Features Various color mixing and effect option
4. al Various color strobe Electronic dimming 0 100 Sound Active inside DMX 512 Computer Control Master Slave Digital operation menu and function button Power off Memorry Electronic Specification Input Voltage 90 250V Lamp Source 1 w high brightness led lamps inside Each panel with 36pcs led lamps R 12 G 12 B 12 Each tile with 4 modules modules are interchangeable Each module are comprised by 9 led lamps Power Supply High quality power switch which are flexible between 110 V and 220 V A good quality power is essential to extend the lifetime of a lamp Lifetime 250000 hours Cin normal operating condition Working Environment 10 C 40 C Cooling Way Convection cooling with no fans Protection Rate IP65 dustproof and shock resistance Which can be used indoor or outdoor Physical Specifications Photo below is the measurement Material ABS base and cover base can bear 100 kg with no shape change and no cover bear Panel Size 500x500x138mm Net Weight 2 8KG Packing Size 560x560x175mm_ 1 pcs Carton xxmm 4 pcs Carton Packing Weight 3 7KG 1 pcs Carton 16 7KG 4 pcs Carton 138mm LED Disco Panel Operating Instructions Sound Active Mode different effects changed with the sound Auto Mode Can change different color automatically and operate the built in program Master Slave Mode The product shall be run in slave mode After all the lamp signal cable and power cord are connected nor
5. ety of effects Detail channel functions please refer to the following lt channels of LED DISCO PANEL gt Use Manual connect the DMX console with the lights by XLR plug and set the DMX address Pixels Distinguish Figure CH 1 auto mode Ces OO e dimer S auto speed from fast to slow effect with positive sequence CH 2 auto speed from slow to fast effect with reverse sequence a FO strobe off CH 3 strobe effect 1 speed from fast to slow valid in auto mode 128 254 128 254 strobe effect 2 speed from slow to fast strobe off iia SE EN hr E E a a Cens m atria es arora we or ea es raa e re a Cen S a a aeRO err 038s S stp aa a cir oss Sp a aig a ea a ae TBO ea ra a a aw CH 16 4 st pixels light green brightness adjusted brighter as value bigger ar es o o E a S CH19 0255 e e N DA an QO O I I o A LED Disco Panel Installation and Settings Safety Precautions Do not spill water or other liquids into the product Ensure that your local power outlet match with the product voltage If the power cord is frayed or damaged do not attempt to operate the product and do not attempt to re moved or broken wire GND which can reduce internal short circuit caused by electric shock and fire hazard Disconnect the main power supply before any type of connection Any case are not allowed to disassemble the cover no parts you can repair or replace ins
6. ide the lamp Do not operate the product when the cover is removed Failure do not force to run the product Disconnect the main power supply when not in use for a long time The path of the power lines should be properly arranged so that the line will not be walked on or pinched Pay special attention to this point while pulled off the line from the device Clean up the product for detail information see cleaning Equipment should position away from heat sources such as radiators stoves or other appliances including amplifiers which can produce heat The following occurs in need of repair A The power cord or the power supply has been injury B Products falling from height or product internal splashed into water or other liquid C Product get wet by rainstorm or water D Product can not operate normally or when significant changes occur in the performance Installation d The connectit o of th signal cable and powe cables between panels KA S The female of one panel should Connect the 3 cores female with Adjust the cables position to let be close to the male of another the 3 cores male Connect the them hide in the grooves of the panel 2 cores female with the 2 cores panels Then put the panels to male And screw up them in the gether clockwise direction Please lock the nearby panels by our cross fixtures Note 500mm from central between two plates as picture shown LED Disco Panel 2 The first or last panel
7. mally select any one of lamp and set the control board to be Auto mode as the host Others are set in the address code d 001 as a slave all the product will be synchronized with the host DMX Control Mode Controlled and edit by international agreement DMX 512 Light will go to Auto mode by setting control board when not have DMX controller connected The effect same change with the first light while many lights connected Connect the lights and connect the DMX controller later go the LED DISCO PANEL channels chart Note Lights are operated by computer if connected with computer software Control Board Control Board 8888 MENU Add Value DOWN gt Reduce Value O O Q lt ENTER gt Confirm Select MENU UP DOWN ENTER menu display and function Settings NO Menu _ 4 A001 console mode or slave mode sound mode AUTO effect 1 AUTO effect 2 AUTO effect 3 2 G 5 AUTO effect 4 4 G 6 AUTO effect 5 ee AUTO effect 6 a G 8 AUTO effect 7 G9 kClightingoff O S S r000 press ENTER to 3 G000 Manual dimming chee color b000 4 FADE effect of pulse variable 5 SMTH gradient effect 6 STRO Random strobe If you want to keep the origin mode after power off include all mode above Please press ENTER to confirm after operation LED Disco Panel DMX Mode Users can create your own needs program by DMX console International standard DMX 512 signal control to achieve a vari
Download Pdf Manuals
Related Search