WiLARM-MICRO GSM Module Installer Manual
Contents
1. Initializing 2 blinks GSM module error 3 blinks SIM card is missing 4 blinks SIM card is locked with PIN code but the PIN code has not given in the programmer software Pushbutton The pushbutton is used for different adjustments of the GSM module erasing the memories and upgrading the internal firmware Deleting the configuration master reset Unplug the device remove the external power supply unplug the USB cable Push the reset button while the device is switched off Plug the power supply and release the Reset button immediately The two LEDs of the module light up and blink once When both LEDs turn off push the Reset button again The green LED shows that the Reset process is done Unplug the device again Erasing and rewriting the internal drive The internal drive of the GSM module can be rewritten only after erasing if you want to upload WiLARM Commander software or documentation WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Unplug the device unplug the external power supply unplug the USB connector Push the reset button while the device is switched off Plug the power supply and release the reset button immediately Both LEDs of the module light up and blink one When both LEDs turn off wait until they light up again When both LEDs turn off again the second time push the Reset button again The green LED signs that2. WiLARM MICRO GSM Module Installer Manual Version 2 0 SIM9GO 52 10405 2091 SL BA LN B 0980 v WiLARM PRECISION SECURITY SYSTEMS WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Content WiLARM MiCRO GSM 2 The parts Of oO Mini USB uie Dun EARN UM Kc Civ RIS 3 Terminal COMPACTS EP P 3 Power SU Nm 3 ACT UE Se 3 Power monitoring sac tk Geb P PR x AE QNEM eiat 3 DE e 4 Opetratiomol the LEDS ossa te arenas 5 PQS 11 M P 5 Deleting the configuration master reset sese nennen 5 Erasing and rewriting the internal enn 5 Copying the software and documentation onto the internal drive 6 Refreshing th internal firmware 6 SIM Bisnes 7 Antenna CONNECTOT uini ne ENAA NEE EEES 7 Prepa
3. an be programmed via SMS commands as well The adjustment of the GSM module can be done with the programmer SMS commands as well as the smaller modifications after the installation dialed phone numbers inputs output parameters etc The detailed commands are available with examples in the SMS commands table Programming SMS commands section Command description Example 1234pin4321 1234pin 4321 Where 1234 is default 4321 is the new code 1234setnum number1 number2 1234setnum 06201234567 06301234567 06701234567 d n n number5 When we write d the place of a phone number then it will be deleted When we write n the place of a phone number it won t be changed 1234setin in1 invertation input Ase Ein inik type sms notification phone Where the first input is inverted 24 hour SMS sending to 1 5 phone numbers Phone call to 1 4 notification phone numbers in2 invertation input type sms The second input is not inverted it is in Autoalarm mode SMS sending to the first phone number notification phone notification phone call to 1 2 phone numbers inverted invertation or not inverted Setting up the first input only input type 1 Not used Setting up the second input only 2 24 hour q294set dm m2 C234 3 Autoalarm 4 Arm Disarm 5 and the number where we want to send the SMS Phone noti
4. fications and the number where we want to send the phone notification WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Sending phone number to the SIM card SIM phone number 1234SIM 36301234567 Deleting the phone number from the SIM card SIM phone numberd Setting up the clock clk YYYY MM DD HH MM YYYY year MM month DD day HH hour 123491M 3630123456Td Deleting the 36301234567 phone number from the card 123481M 1234567d Deleting all 1234567 ended phone number from the SIM card Back It sets the GSM clock February 25 2012 11 hour 21 minutes Controlling the GSM module with commands The device can be controlled via the command SMS test arming switching output etc The detailed commands are reachable with examples in the SMS commands table Controlling SMS commands section Test request 1234t In this case the GSM module responds a status SMS about the arming status of the inputs outputs inner clock temperature power voltage Turning off the inputs outon Turning on the inputs outoff Turning off the inputs Arm mode on off on off GSM module RESET 1234reset Control commands 1234t 1234outon 1 activating the first output 1234outon 4 activating the multiport 4 truning off the output 1 Ze 4 out oBt2 turning off the relay 2 or the mul
5. menu Antenna connector Standard SMA F connector The supplied stick antenna can be connected here or the optional types with extension cable Prepare for the installation Insert the SIM card to your mobile phone disable voice mail service activate the callerID sending do a network signal strength measurement Insert a SIM card without a PIN code request into the GSM module connect the power supply and do a network signal strength measurement with the green LED Programming using WiLARM Commander software All of the available functions of the module can be adjusted via the WiLARM Commander exe software After connecting the power supply and the USB the module appears as a WiLARM drive in My computer on the desktop The content of it can be seen while opening the software and the documentation in PDF format The software is universal all WiLARM modules can be programmed with it After connecting it the software recognizes the type of the module and the proper setting screen appears If the module is not connected then all parameters can be seen regarding all types of modules WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Y The WiLARM Commander software has a built in help The cursor can be stopped on any kind of place of the menu the help will appear for the use of the current menu Programming with SMS commands The main parameters of the GSM module c
6. mmander Software they can be configured as open collector outputs In this case the load current can be maximum 100 mA they can be configured similar to the relays Power monitoring input Module measures the accurate value of the input power Can be parameterized like contact inputs Additionally user can set lower and upper voltage values which exceeded module will send alarm WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Antenna connector Activity and GSM Mounting holes ACI network LEDs GSM module Terminal contacts LEDs The green and the red LEDs show the module status in operation The red LED shows some kind of activity the green LED shows the strength of the network signal strength in normal operation When the green and the red LEDs are blinking together then the device does not work the number of the blinking shows an error code The error code can be seen on the status window of the WiLARM Commander software WiLARM MICRO GSM Module 5 TTA Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Operation of the LEDs Lighting continuously It can not connect to the network 1 2 blinks Low network signal strength another place or external antenna is recommended 3 blinks Reasonable network signal strength a test call is suggested 4 blinks Good network signal strength 5 blinks Excellent network signal strength 1 blinks
7. re for the Ista WAU ON 7 Programming using WiLARM Commander software seen 7 Programming with SMS COPITIBIS 8 Controlling the GSM module with commands een 9 Barolo cere re npo 10 WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS The parts of the module Mini USB connector The WiLARM GSM module can be programmed via the mini USB connector When it is connected WiLARM as new drive called WiLARM appears in the my computer icon on the desktop Clicking onto the drive the WiLARM Commander software and a PDF documentation appear The internal software of the module can be refreshed via the mini USB connector The WiLARM Upgrader software documentation includes the whole detailed user manual Terminal contacts The power supply and the different inputs and outputs can be connected to the GSM module via the terminal contacts Power supply The module operates from 9 12 Volt DC The idle current consumption of the module is 30mA but during communication it can reach 2 Amperes as well Inputs and outputs The contact inputs can operate in normally closed NC referenced to the ground GND or normally opened NO modes Changing the default state starts the alarm The multiport inputs are contact operated as well but with the WiLARM Co
8. the erasing process has happened Unplug the device Copying the software and documentation onto the internal drive After deleting the internal drive plug the power supply and then the USB cable to the module n My computer the module appears as a new drive on the desktop Format the drive check the size 3 Mb the volume label should be WiLARM Copy the necessary software and documentation to the drive Unplug the device Refreshing the internal firmware Launch the Wilarm Upgrade exe software Unplug the device remove the power supply unplug the USB connector Hold on the reset button and plug the USB cable The LEDs light at low intensity which means that the module is in BOOT mode Attention If you do not start the refreshment within 10 seconds the module automatically leaves BOOT mode and restarts itself Open the firmware with the Open Upgrade button WiLARM MICRO GSM Module TTA Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS The refreshment of the internal software has been starting Atthe end of the process the PASS title signs the successful finish Restart the WiLARM GSM module SIM holder The holder of SIM card the SIM was bought from the network service The device is card independent so it accepts any kind of cards It is better to switch off the PIN request of the SIM card if it is not possible the PIN code can be adjusted in the WiLARM Commander
9. tiport output bistable mode 1234on 12340ff 1234reset WiLARM MICRO GSM Module Installer Manual Version 2 0 PRECISION SECURITY SYSTEMS Troubleshooting Troubleshooting Caller identification does not work Check the service provider that on the SIM card the caller ID for outgoing calls is turned on Check the caller ID of the controllable phone as well Check the Only SIM reg Number at call settings as well as the phone numbers have already typed to the SIM card ACT LED stays red during alarm The module can not send the message because the card is out of credit or a wrong phone number was given Check the SMS center number of the module SIM card WiLARM Commander doesn t not recognize the module The USB cable is long Try with a shorter cable or plug the cable directly to the USB port of the computer Check if external 12V power supply is connected The caller phone number GSM module can not be seen caller ID is disabled on the card The module sometimes does not call The very old cards more than 10 years could cause problem 10 1115 5 Csoka str 7 13 A Tel 36 1 466 5665 E mail info wilarmsecurity com Web http www wilarmsecurity com LARM SECURITY SYSTEMS
Download Pdf Manuals
Related Search