Instruction Manual
Contents
1. NEVER NEVER Je NEVER NEVER E deda fe LEGAL WARKING In most jurisdictions it is illegal for a person under the age of 18 to possess and or operate a firearm unless under the direct supervision of an adult The adult owner of this firearm must ensure that no minors handle this firearm without his hers direct supervision In some states you may be fined and or sent to prison FEDERAL LAW It is unlawful to sell a handgun to any person less than 21 years of age Doing so can result in fines and or imprisonment OPERATING INSTRUCTIONS SCCY Industries strongly urges you to review the following procedures Follow them carefully to learn the basic functions and handling characteristics of your new firearm It is strongly recommended that you retain these instructions for future reference If you transfer ownership of this firearm this instruction manual must be included Do not load the firearm until you have read all operating instructions at least one time If the firearm is loaded do not attempt to unload the firearm until you have read these instructions see page 17 UNLOADING THE FIREARM Throughout the following procedures always point your firearm in a safe direction Keep your finger s off the trigger and out of the trigger guard area Grasp and hold the firearm firmly see page 12 PROPER GRIP CONTROL Remove the magazine and check the chamber to make certain the firearm is unloaded Yo2. the firearm may require cleaning and oiling see page 20 If the problem continues please contact a local gunsmith or SCCY Industries ADJUSTING THE REAR SIGHT Using a 1 16 allen wrench loosen counterclockwise the set screw located in the rear sight as shown in Figure 15 Then slide the rear sight to its desired location and tighten the set screw clockwise MAKE SURE FIREARM IS UNLOADED To move the point of impact to the left move the rear sight to the left To move the point of impact to the right move the rear sight to the right Make small gradual adjustments until the firearm is sighted in WINDAGE The model CPX s sighting system Is for windage adjustments only left or right The Front Sight is Figure 15 permanently mounted and cannot be adjusted DISASSEMBLY FOR CLEANING STEP 1 With the firearm unloaded and the safety in the ON UP position model CPX 1 only firmly grip the firearm with one hand With the other hand pull back the slide as shown in Figure 16 If there is an empty magazine in the magazine well the slide hold lever will lock the slide in its rear position If there is no magazine present the slide hold lever will need to be pushed up manually to lock into place PULL SLIDE BACK PUSH UP ON SLIDE HOLD IF NO MAGAZINE IS PRESENT Figure 16 NEVER DISASSEMBLE A LOADED FIREARM DOING SO CAN CAUSE SERIOUS INJURY OR DEATH TO SELF AND OR BYSTANDERS 19 STEP 2 Using
3. 01 054 01 015 01 049 res RECEIVER TRIGGER TRIGGER BAR PLUNGER SPRING TRIGGER SPRING TRIGGER CAM HAMMER HAMMER SPING PIN HAMMER AXIS PIN HAMMER SPRING SLIDE HOLD SPRING EJECTOR PIN EJECTOR SLIDE HOLD SAFETY LEVER RIGHT SAFETY LEVER LEFT PLUNGER SAFETY LEVER SCREW 01 018 01 007 j 01 029 01 031 4 01 007 01 010 01 014 01 015 01 016 01 018 01 022 01 031 01 024 01 028 01 029 01 082 01 036 01 048 01 049 01 053 01 054 01 016 REGEIVER PARTS LIST CALL 5 00 5 00 3 00 3 00 7 00 7 00 2 00 3 00 3 00 3 00 1 00 3 00 5 00 5 00 3 00 2 00 2 00 01 014 01 048 01 025 ty 31 SLIDE PARTS LIST SLIDE EXTRACTOR FIRING PIN SPRING EXTRACTOR PIN EXTRACTOR SPRING FRONT SIGHT FIRING PIN REAR SIGHT BARREL FIRING PIN RETAINER RECOIL SPRING SUB ASSEMBLY REAR SIGHT ADJUSTMENT SCREW 01 038 t 01 009 01 009 01 012 01 020 01 026 01027 01 038 01 039 01 040 01 041 01 052 01 056 01 058 125 00 5 00 3 00 1 00 3 00 5 00 7 00 7 00 30 00 3 00 9 00 1 00 GLOSSARY This glossary is to define terms as used throughout this manual and to help the beginner better understand firearm terminology Ammunition Ammo Cartridge A casing bullet primer and gun powder becomes a cartridge and is used in a firearm Ammunition comes in many different calibers Ambidextrous Safety A safety system that
4. CPX 1 CPX 2 SERIES Instruction Manual INDUSTRIES The American firearms company founded on the radical notion that the customer comes first IMPORTANT NOTE Throughout this document references to a manual safety apply only to the model CPX 1 The CPX 2 is designed without a manual safety IMPORTANTISAFETV MESSAGE DO NOT OPERATE THIS FIREARM UNTIL YOU READ THE ENTIRE INSTRUCTION MANUAL INTRODUCTION This manual is designed to warn you about the dangers and responsibilities associated with handling firearms Do not attempt to load unload or handle this firearm until you have read and understand the contents of this manual The warnings in this manual must be followed for your safety as well as for the safety of bystanders If after reading these Instructions you still do not understand the firearm entirely please consult with a firearms instructor for further instructions CONTENTS 2 Misfire Failure to PESO 18 COM nia 3 Adjusting the Rear Sight 18 Warning Messages 2 5 Disassembly For Cleaning 19 Legal Warning nee 5 A aan 22 5 ReassemblyY anna 23 Operating Instructions 6 Child Resistant Lock 25 Component NAMES une 7 Installing the 25 Basic 8 Pr
5. PED HOLE ALIGN THIS AREA WITH HOLE IN RECEIVER Figure 23 Figure 24 STEP 4 Making certain the disassembly pin is snapped into location all the way in as shown in Figure 25 pull down on the slide hold lever allowing the slide to move forward to the locked position Before loading you should manually SUE check the operation of the slide barrel and firing system to ensure the firearm is assembled properly When the slide is pulled rearward and released the barrel should unlock and lock Test the firing system by pulling the trigger several times ensuring the hammer strikes the firing pin properly Figure 25 24 CHILD RESISTANT LOCK The model CPX is supplied with a custom fitted child resistant trigger LOCK Bess SHOWN guard lock as shown in Figure 26 OPEN designed specifically for the model CPX In addition the lock is supplied with 2 keys NEVER INSTALL THE LOCK ONA LOADED FIREARM The trigger guard lock should always Figure 26 be installed on the firearm when the firearm is not in use Also see STORING AND TRANSPORTING THE MODEL CPX on page 26 Should the trigger guard lock become damaged or lost SCCY Industries will replace it for just shipping and handling charges Some states require that all firearms be locked when the firearm is not in use When the lock is in the open position the key stays with the lock and cannot be removed The trigger guard lock can be Installed on the fi
6. asmall flat blade screwdriver or the rim of a spent cartridge insert into the slot found in the top of the disassembly pin as shown in Figure 17 and Figure 18 With light pressure pry outward in the direction the arrow displays until the disassembly pin is removed as shown in Figure 19 FLATBLADE SCREWDRIVER DISASSEMBLY PIN Figure 17 Figure 18 N Figure 19 20 STEP 3 Move the slide forward It should now move freely off the receiver as shown in Figure 20 For further disassembly refer to the subassembly exploded views on pages 29 through 32 Figure 20 21 22 CLEANING AND DILING To ensure proper operation of the firearm it is necessary to keep the firearm s internal components clean and lubricated After completing the disassembly procedure steps 1 through 3 the firearm is now ready for cleaning Normal cleaning Is easily accomplished by using common gun cleaning fluids either liquid or aerosol to remove any gun powder residue Do not use any water based household cleaning products such as detergents they can Cause corrosion Apply alight coat of gun oil to all internal surfaces excluding the firing pin hole This allows a smoother operation while protecting the firearm from corrosion The slide barrel and recoil spring subassembly can be separated for cleaning see page 32 SLIDE PARTS LIST Clean the gun powder residue from the top of the receiver area and apply a light coat of
7. azine inspected cleaned and packaged SCCY Industries cannot control the subsequent handling when your firearm left the factory Therefore examine your firearm carefully before firing it INDUSTRIES www sccy com FEATURE 9mm 10 Round Magazine Capacity an Extra Magaz Lock Breach Stainless Steel Slid Stainless Steel Barrel Ambidextrous Safety Slide Holds Open on Last Round Adjustable Rear Sight Internal Hammer Double Action Only DAO Polymer Frame Child Resistant Lock Lightweight amp Compact Magazine Finger Rest SCCY INDUSTRIES LLC 1800 CONCEPT COURT DAYTONA BEACH FLORIDA 32114 866 729 7599 SALES SCCY COM SERVICE SCCY COM
8. can be applied from either side of the firearm The model CPX 2 does not possess a safety Barrel The firearm component through which the bullet travels Bore The hole in the barrel that is rifled Breech Face A face on the slide that supports the cartridge in the barrel Cartridge See Ammunition Chamber A portion of a barrel that houses a cartridge Double Action The style of a firing mechanism The trigger is pulled only once to cock and discharge the firearm Discharge The firing of a cartridge Ejector A component of a firearm used to eject an empty cartridge Extractor A component of a firearm that pulls the cartridge out of the chamber Feeding The process in which the slide pushes a cartridge from the magazine into the chamber Feed Lips The upper portion of the magazine that retains and positions the cartridges to the chamber Firing Pin The component of a firearm that strikes the primer area of a cartridge Grip The portion of a frame where the firearm is held Hammer The component of a firearm that strikes the firing pin Lock Breech When the barrel and slide are locked together to contain the chamber pressures created by shooting Magazine An accessory of a firearm that stores live cartridges before being discharged Magazine Release A component of a firearm used to hold the magazine in place and that when pushed releases the magazine Magazine Well The hollow portion of a firearm
9. dge is present If a cartridge is present your firearm is ready to be discharged fired If you do not intend to shoot at this time you should unload your firearm including the cartridge in the chamber Refer to page 15 UNLOADING YOUR FIREARM CHAMBER AREA TRIGGER AREA Figure 11 DANGER ALWAYS CHECK THE CHAMBER Never assume a firearm is unloaded when placing an empty magazine into the firearm Installing an empty magazine into the firearm and pulling the trigger will discharge a cartridge in the chamber This firearm will discharge without a magazine installed 14 SLIDE HOLD OPEN After firing the last cartridge the slide will remain open see Figure 12 This allows the operator to visually check the chamber and magazine area to make certain the firearm is empty If you Intend to reload the firearm replace the empty magazine with a full one Firmly hold the firearm by the grip area press down on the slide hold open lever This will allow the slide to return to its forward locked position while feeding a cartridge into the chamber The firearm Is now ready to be discharged SLIDE HOLD ENGAGED Figure 12 AMMUNITION The model CPX is designed for 9mm LUGER ammunition only seen in Figure 13 The caliber is marked on the barrel and the cartridge Make certain 9mm LUGER is used only The use of improper size ammunition will cause damage to the firearm and or injury or death to shooter and or bystanders It
10. e direction while keeping finger s off the trigger and out of the trigger guard area First remove the magazine Pull and hold the slide rearward the cartridge in the chamber will eject through the ejection port Inspect to make certain no cartridge is present in the chamber REMOVING THE MAGAZINE DOES NOT REMOVE A CARTRIDGE FROM THE CHAMBER THIS FIREARM WILL DISCHARGE WITHOUT A MAGAZINE INSTALLED MANUAL SAFETY FEATURE AND ASSOCIATED INFORMATION ARE ONLY APPLICABLE TO MODEL CPX 1 z MISFIRE FAILURE TO FEED OR EJECT Keep the firearm pointed at the target for no less than 30 seconds This will allow adequate time for a delayed cartridge to fire Unload the firearm following the UNLOADING THE FIREARM procedure on page 17 Remember to remove the magazine from the firearm before ejecting the chambered cartridge Occasionally a semi automatic firearm may fail to feed or eject a cartridge If this should happen perform the following procedures e Keep fingers off of the trigger Keep the firearm pointed in a safe direction during this entire procedure e Remove the magazine Pull the slide rearward and remove any cartridge that is present in the chamber area Inspect the cartridge that failed to feed or eject for dent or any other defects A defective cartridge should be discarded and not used e Inspect the remaining cartridges in the magazine before continuing to discharge the firearm If failure to feed or eject continues
11. e extractor and being pushed by the ejector force the empty cartridge out of the slide s ejection port EJECTED CARTRIDGE Figure 4 STEP 4 The slide is moved forward by spring forces generated through the recoil spring sub assembly see part number 01 056 Recoil Spring Sub Assembly on page 32 As the slide moves forward it picks up another cartridge from the magazine and feeds it into the chamber as shown in Figure 5 Once the slide reaches its fully forward position the barrel locks up to the slide as shown in Figure 1 on page 6 and the firearm is ready to be discharged again This cycle can be repeated until the magazine is emptied CARTRIDGE BEING FED INTO CHAMBER RECOIL SPRING SUB ASSI Figure 5 11 PROPER GRIP CONTROL When preparing to shoot the firearm firmly grasp the grip area of the firearm as shown in Figure 6 To pull the slide back firmly grasp the firearm s grip area with one hand With the other hand firmly grip the slide serrations area and smoothly pull the slide back as shown in Figure 7 Figure 6 DANGER The finger s must remain clear of the trigger guard area until ready to discharge the firearm Figure 7 12 MANUAL SAFETY MODEL CPX 1 ONLY The manual safety found on CPX 1 only is located on both the right and left side ambidextrous of the grip area and should ALWAYS be placed in the SAFE position until ready to fire The safety rotate
12. gned by an adult To expedite questions regarding the status of your firearm while being serviced please record the firearm s serial number and refer to it while speaking to the service technician All returned firearms shipped back to their owner must be received by and signed by an adult 21 years of age or older or the shipment will be returned 27 REPLACEMENT PARTS Should your model CPX require service or maintenance contact SCCY Industries 1800 Concept Court Daytona Beach FL 32114 Call Toll Free 866 729 7599 Business hours are 8 30am to 5 00pm Monday through Friday EST Refer to pages 29 through 32 for individual part numbers e Please be advised that the receiver part number 01 007 must be replaced by the factory only Return of the entire firearm is mandatory e Individual parts for magazines are not available magazines are only sold as full assemblies RECORD AND STORE THE MODEL CPX SERIAL NUMBER KEEP IN A SAFE PLACE BEFORE SHIPPING BACK TO THE FACTORY 28 FULL ASSEMBLY FRAME PIN 2 01 030 3 00 DISASSEMBLY PIN 01 037 7 00 01 030 Please consult factory or check SCCY com to confirm current pricing before ordering 29 FRAME PARTS LIST FRAME MAGAZINE RELEASE END CAP PIN END CAP MAGAZINE RELEASE SPRING 01 034 f 01 023 01 008 02 013 01023 01 033 01 034 15 00 5 00 1 00 3 00 2 00 01 010 01 028 Ig 01 _ A ER 01 024
13. is highly recommended that top quality factory manufactured ammunition be used only The use of reloaded or military surplus ammunition can cause jamming problems and possible serious injury to shooter and bystanders CR Never use ammunition that is wet corroded dirty bent crushed or is otherwise damaged Figure 13 15 LOADING THE MAGAZINE Use the proper size ammunition Insert a cartridge into the feed lip area using light pressure in a downward fashion as shown in Figure14 Never force cartridges into the magazine As the magazine fills to capacity 10 cartridges the amount of pressure increases due to spring preload When cartridges are visible at the top hole this indicates there are 5 or more cartridges in the magazine When cartridges are visible at the bottom hole this indicates the magazine Is full Never force more than 10 cartridges into the magazine Doing so can cause damage to the magazine and its internal components FEED LIP AREA LOAD IN THIS DIRECTION Figure 14 WARNING P CARTRIDGES SHOULD ONLY BE USED ON A LIMITED BASIS INTHE MODEL CPX This type of ammunition creates much higher chamber pressures than standard ammunition Never fire more than 50 rounds of P ammunition per session PREPARING TO SHOOT Always point the firearm in a safe direction Any and all firearms are dangerous if not handled properly Always wear proper eye and ear protection Lock slide BEFORE inserting l
14. le action firing mechanism is when the trigger is pulled and the trigger bar engages the hammer and pulls it back to the cocked position as shown in Figure 2 The hammer can not remain in the cocked position due to its design It automatically releases once reaching its fully cocked position HAMMER COCKED A m Zn TRIGGER PULLED Figure 2 STEP 2 The second half of the DAO double action firing mechanism is when the hammer snaps forward contacting the firing pin causing it to strike the primer area of the cartridge as shown in Figure 3 The primer ignites the gun powder in the cartridge The ignited powder is turned into expanding gases forcing the bullet out of the barrel As the bullet moves through the barrel s bore it engages the rifling thus causing it to spin The spinning motion of a bullet allows it to travel to the point of impact with a higher degree of accuracy FIRING PIN STRIKES PRIMER Figure 3 10 STEP 3 The expanding gases also push the empty case back causing the slide to move back as shown in Figure 4 The shooter will now experience perceived recoil As the slide is moved back the empty cartridge is held and carried back by the extractor see part number 01 012 extractor on page 32 When the slide reaches its fully recoiled position the empty cartridge makes contact with the ejector see part number 01 032 ejector on page 31 The combining forces between the empty cartridge being held by th
15. oaded magazine With the firearm pointed in a safe direction insert a loaded magazine into the magazine well until it locks into place Pull the slide back and lock it with the slide hold lever Release the slide hold lever when ready to feed a cartridge from the magazine into the chamber When ready to discharge the firearm rotate the safety lever to the FIRE position IMPORTANT NOTE Since the CPX 2 lacks a manual safety it is ready to fire as soon as a Cartridge is fed into the chamber If the firearm is in the slide hold position insert a full magazine Press the slide hold lever to release the side Once you press the lever let the slide close unassisted do not grip or touch the slide as it travels forward This will feed a cartridge from the magazine into the chamber The firearm is now loaded and ready to be discharged Firmly grasp the firearm point the firearm at the target and carefully pull the trigger The firearm will discharge and automatically feed the next cartridge from the magazine into the chamber The firearm is now ready to be fired again Each time the trigger is pulled the firearm will discharge until all cartridges in the magazine and chamber have been fired When the last cartridge has been discharged the slide hold lever will cause the slide to remain in its rearward position UNLOADING THE FIREARM Place the safety in the safe position model CPX 1 only Point the firearm in a saf
16. oil to the top of the receiver and hammer area Also apply a light coat of oil to the inside of the feed lip area of the magazine allowing oil to coat the inside of the magazine body Any further disassembly is not necessary under normal usage REASSEMBLY STEP 1 Assemble the barrel slide and recoil subassembly making certain that the recoil subassembly is seated properly Note the smallest end of the recoil spring subassembly is placed In the hole on the front of the slide The large end is seated on the barrel lug Point firearm downward and align the slide with rails on the receiver slide into place as shown in Figure 21 There should be no magazine present during this process RAIL AREA ON RECEIVER Figure 21 MAKE CERTAIN THERE IS NO CARTRIDGE IN THE CHAMBER DURING REASSEMBLY STEP 2 Push the slide all the way back while manually applying upward pressure on the slide hold lever until it engages and holds the slide into place as shown in Figure 22 It is normal to feel pressure this is due to compressing the recoil spring subassembly SLIDE HOLD ENGAGED Figure 22 LINE UP BARREL TO RECEIVER 23 STEP 3 Make certain the barrel is pulled full forward and the kidney shaped hole in the barrel see Figure 23 is aligned properly If not move the barrel back and forth until it lines up Then push the disassembly pin all the way In until it snaps into place as shown in Figure 24 KIDNEY SHA
17. oper Grip Control 12 Storing and Transporting Manual Safety 13 the Model CPX 26 Removing the Magazine un 13 Limited Warranty 27 Checking the Chamber 14 Slide Hold Open 15 Replacement Parts 28 Ammunition nn 15 F R ee 29 Loading the Magazine 16 Frame Parts ISU nidad 30 Preparing to Shoot 17 Receiver Parts List 31 Filing anne 17 nee 32 Unloading the Firearm CN TS cc 33 LIMITED WARRANTY STATEMENT The model CPX firearm has a lifetime warranty and is warranted to be free from defects in material and workmanship SCCY Industries will not be responsible for any defects caused by careless handling unauthorized adjustment modifications improper ammunition corrosion neglect abuse normal wear and tear or any unreasonable use In the event your firearm requires service beyond the warranty due to neglect or improper use SCCY Industries will contact you and give you an estimate of charges before any work is performed Any charges must be paid in full before the firearm is shipped back to you Any such defects will be remedied by SCCY Industries pending SCCY Industries inspection of the entire firearm Service due to defects in material and or workmanship will be free of charge Contact the factory at 866 729 7599 and speak with the service department before shipping your firearm
18. rearm with or without the magazine present INSTALLING THE TRIGGER GUARD LOCK STEP 1 With the safety in SAFE position model CPX 1 only and the trigger lock in the open position place the back half of the lock on the trigger guard as shown in Figure 27 Make certain the trigger fits between the two housings FIT TRIGGER BETWEEN THESE 2 AREAS Figure 27 25 26 STEP 2 While firmly holding the firearm and back of the lock with one hand use the free hand to swing the front of the lock closed The two halves of the lock should now be mated securely around the firearms trigger guard as shown in Figure 28 Figure 28 STEP 3 While firmly holding the two lock halves closed with one hand use the free hand to turn the key clockwise right to the lock position Now the key can be removed STORE KEY S OUT OF REACH OF CHILDREN STORING AND TRANSPORTING THE MODEL CPX Do not discard the box the CPX was purchased in It is specifically designed to store the firearm with the lock installed along with the spare magazine Always store your firearm with the child resistant lock installed Keep the firearm and keys in separate places out of reach of children Never store your firearm and spare magazine loaded Never store ammunition with a firearm Always store firearms and ammunition in separate places Prior to transporting your firearm make certain it is unloaded see page 17 UNLOADING THE FIREARM Contac
19. s frame that houses the magazine P Ammunition Ammunition with a higher amount of gunpowder used to test firearm chamber pressures Primer The component of ammunition that when struck by the firing pin ignites the gunpowder inside ammunition Receiver The main component of a firearm that all the other firearm components attach to Recoil The reaction felt by the shooter after discharging a firearm Rifling A series of spiraled grooves in the bore portion of a barrel causing the projectile to spin Slide A major component of the firearm that moves back and forward to feed and eject cartridges This component also contains the barrel firing pin and recoil spring assembly Serrations A portion on the back of the slide that the shooter grips when pulling back the slide Serial Number A unique number given to each firearm used to identify it Spring Preload Forces generated by spring pressure Trigger Bar A component of a firearm firing mechanism that links the trigger to the hammer Windage The left and right adjustment of a sight on a firearm 34 Thank you for purchasing SCCY Industries Model CPX We at SCCY Industries are committed to supplying the firearms industry with the finest possible products If you follow these instructions carefully the Model CPX should give you many years of fine service Remember Safety First Before this firearm left the factory it was test fired with a full mag
20. s up and down between the SAFE and FIRE position See Figure 8 safety shown in SAFE position See Figure 9 safety shown in FIRE position a Figure 8 Figure 9 REMOVING THE MAGAZINE E With the safety in the safe position press the magazine release button as shown in Figure 10 while maintaining a firm grip on the firearm The magazine will drop freely from the magazine well Do not allow the magazine to fall on the ground MAGAZINE RELEASE To insert a magazine into the firearm align it with the magazine well and firmly slide it until it locks into place Do not force the magazine into the magazine well or strike the magazine base to seat the magazine Doing so may Figure 10 cause damage to the magazine The magazine release procedure can be done either in the slide hold position as shown or with the slide forward and locked REMOVING THE MAGAZINE DOES NOT REMOVE A CARTRIDGE FROM THE CHAMBER THIS FIREARM WILL DISCHARGE WITHOUT A MAGAZINE INSTALLED MANUAL SAFETY FEATURE AND ASSOCIATED INFORMATION ARE ONLY APPLICABLE TO MODEL CPX 1 13 CHECRING CHAMBER FOR AMMUNITION To view inside the chamber place safety in safe position model CPX 1 only remove the magazine and then pull back the slide approximately 1 inch see Figure 11 While doing so always have your finger s clear of the trigger area Visually inspect inside the chamber and magazine area to see If a cartri
21. t your local law enforcement official for approved methods of firearms transportation It is unlawful to ship a firearm to anyone other than the manufacturer or from dealer to dealer If you require shipping your firearm make certain to log the firearm s serial number LIMITED WARRANTY STATEMENT The model CPX firearm is warranted to be free from defect s in material and workmanship for a lifetime from the date of purchase Any such defects will be remedied by SCCY Industries pending SCCY Industries inspection of the entire firearm Service due to defect s within the terms of the warranty will be free of charge Contact the factory at 866 729 7599 and speak with the service department before shipping your firearm for service SCCY Industries will not be responsible for any defect s caused by careless handling unauthorized adjustment modifications improper ammunition corrosion neglect abuse normal wear and tear or any unreasonable use In the event that your firearm requires service beyond the warranty terms SCCY Industries will contact you and give you an estimate of charges before any work is performed Any charges must be paid in full before the firearm is shipped back to you To ensure a quick turn around enclose a note stating the problem you are experiencing with your firearm Be sure to include the firearm s return address and contact telephone number All firearm shipments must be received by and si
22. u or anyone you permit to handle this firearm must review and understand the entire instruction manual before handling the firearm After reading the entire instruction manual read through it again this time examining the firearm in an unloaded condition to acquaint yourself with the features described in this manual If after reviewing these instructions and examining the firearm you are unsure of how to safely operate the firearm contact a certified firearm safety instructor for further instruction When discharging your firearm you and bystanders should wear eye and ear protection at all times NOTE MANUAL SAFETY FEATURE AND ASSOCIATED INFORMATION ARE ONLY APPLICABLE TO MODEL CPX 1 COMPONENT NAMES SLIDE SLIDE HOLD LEVER FRONT SIGHT DISASSEMBLY PIN SERRATIONS LEFT SAFETY LEVER CPX 1 17 GRIP AREA MAGAZINE RELEASE FRAME MAGAZINE BASE REAR SIGHT EXTRACTOR BARREL SERRATIONS RIGHT SAFETY LEVER CPX 1 TRIGGER GUARD AREA TRIGGER GRIP AREA 4 MAGAZINE BASE BASIC FUNCTIONS This section will describe the basic functions of the model CPX firearm As shown in Figure 1 the firearm is in the ready to shoot configuration The Model CPX utilizes a Double Action Only DAO firing mechanism and will be explained in further detail throughout this section CARTRIDGE IN CHAMBER HAMMER TRIGGER FORWARD Figure 1 STEP 1 The first half of the DAO doub
Download Pdf Manuals
Related Search