Nokta Velox One
Contents
1. 2 NY Sel www noktaengineering com USER MANUAL INTRODUCTION Thank you for choosing and purchasing our Nokta Velox One detector Manufacturing high tech metal detectors since 2001 Nokta Engineering has played a key role in the development of this sector Nokta Engineering is particularly known for its technological know how and professional staff Seeking to create different kind of technology Nokta Engineering offers both high quality products and services to its consumers all around the world Nokta Engineering has been operating under the principle that environmental and community responsibility customer satisfaction and insistence on high quality are of the utmost importance Nokta Engineering aims to remain a leading pioneer in its sector winning the trust of its consumers and always being the preferred choice for metal detecting Oo 9 Nokta NOKTA ENGINEERING INTRODUCTION WARNINGS ee 3 4 ASSEMBLE te sa a ee 5 8 CORRECT WAY HOLDING 9 CORRECT WAY OF SWEEPING BATTERY 5 2 ata ba erate 11 DEVICE INTRODUCTION 12 TREE 13 16 TURNING ON THE DEVICE 13 GROUND BALANCE 13 14 a a2. It is very important to adjust the shaft to your height correctly to be Adjust the height of the shaft so that you are standing in an upright able to search without discomfort and fatigue position your arm is relaxed and the search coil is approximately 5cm 2 above the ground MENN NOKTA ENGINEERIN CORRECT WAY OF SWEEPING wa Wrong search coil angle Wrong search coil angle Correct search coil angle Incorrect way of sweeping Correct way of sweeping It is important to keep the search The search coil must be parallel to the parallel to the ground in order to get ground at all times accurate results MN Velox BAT TERY CHARGING THE BATTERY The battery pack consists of an 11 1V Lithium Polymer battery and a charging circuit The device comes with a 110 220V AC charger When fully charged the battery will provide approximately 25 30 hours of use The charger will recharge an empty battery in approximately 5 6 hours You don t need to fully discharge the battery before recharging ji BD BATTERY To charge the battery insert the power cable jack into the socket on the side of the battery and plug the power cable into a 110 220 Volt wall outlet The LED on the charger will light up red while charging When charging is complete it will turn green This LED will also light up green if the charger is plugged into an outlet without the battery installed in it Le To see the battery life status pres
3. MN Velox SEARCHING AND METAL DETECTION SEARCHING AND METAL DETECTION After the settings are adjusted you can start searching by lifting the search coil 56111 above the ground and sweeping it right and left keeping it parallel to the ground The device operates on the principle of motion This means that you must move the search coil over the target or the target over the search coil in order for the device to see it In other words metal detection is not possible without moving the search coil To avoid missing smaller and deeper targets sweep the search coil both from right to left and left to right over each area you are scanning slightly overlapping the sweeps as you move forward When the device detects metal it will produce an audible tone The device has 3 tone audio discrimination The lower tone is for ferrous metals For non ferrous metals and gold the device produces 2 very similar high tones In case of alloy detection the device may produce a high low double tone sound In order to get familiar with the different tones of your device it is recommended that you practice with different types of metals and identify the sounds before you use it out in the field NOTE Discrimination just like in any other metal detector may not always be 100 accurate There are many different factors affecting discrimination accuracy All metals based on their conductivity shape orientation underground depth and ground mineralizat
4. you or an unauthorized person NOKTA ENGINEERING WARNINGS Do not use the device indoors The device will constantly give target signals inside places like homes where there are many metals present Use the device outdoors in open fields Do not let another detector or an electromagnetic device come in close proximity 10m 33ft to the device Do not carry any metal objects while using the device Keep the device away from your shoes while walking The device may detect the metals on you or inside your shoes as targets For Consumers within the European Union Do not dispose of ISO 9001 this equipment in general household waste The crossed Registered wheeled bin symbol on this equipment indicates this unit should not be disposed of in general household waste but This device complies with Part 15 of the FCC Rules Operation is recycled in compliance with local government regulations subject to the following two conditions 1 this device may not cause and environmental requirements harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation MN Velox ASSEMBLY Velox ASSEMBLY NOKTA ENGINEERING a co 2 A lt NA A 9 W 2 CORRECT WAY OF HOLDING
5. ab aia an sitan 14 IRON DISCRIMINATION 15 IRON SWITCH es 15 MINERAL MODES iii 16 SIGNAL AUDIO BOOST 16 SEARCHING AND METAL DETECTION 17 MN Velox WARNINGS LEGAL WARNINGS gt When using the device comply with all applicable laws and regulations Do not use the device in private premises historic sites and military zones Notify the authorities of any historical or cultural findings WARNINGS ABOUT THE DEVICE gt This is a high tech electronic device Do not assemble or use the device before reading the user manual The battery used in the device is specifically designed for Velox One Do not use any other battery Before using the battery you must read all instructions and warnings in the user manual Do not expose the device or the search coil to very hot or cold conditions for extended periods of time Storage Temperature 0 C 32 F 40 C 104 F Do not immerse the device or its accessories except the search coil in water do not expose them to extreme humid conditions gt Protect the device from external impact especially during transportation gt The device can only be opened and repaired by authorized service technicians The warranty will be voided if the device is opened by
6. b to OFF position when you want to turn off the device When the device is turned on a melody will be heard and approximately 10 seconds later you will hear long beep indicating that the device is Mineral 3 SANN ready to use The device will provide more depth at on position However to better discriminate ferrous metals using the device in mineral modes and the iron discrimination at maximum position isrecommended Especially in mineralized ground target signal is negatively affected by the noise caused by ground mineralization This situation may prevent the detector from getting a clean signal from the target necessary for metal detection and accurate discrimination Ground balancing is a process through which the metal detector is able to cancel out the negative effects 10 caused by ground mineralization GROUND BALANCE To ground balance holding the search coil 5cm above the ground sweep it right and left keeping it parallel to the ground and slowly turn the ground balance knob clockwise until the noise is gone and the device is silent If you cannot ground balance the detector gradually decrease the sensitivity and repeat the above steps NOKTA ENGINEERING CONTROLS For makimum depth do not turn the ground balance knob to the right more than necessary Generally speaking the mid level between 4 7 offers the most ideal and stable detection capability on different types of ground without sacrificing
7. depth As the ground balance goes into the right area the device will start losing depth for some non ferrous metals except for gold When the ground balance setting reaches the maximum point the device will detect iron and gold but it will not detect some non ferrous metals 10 GROUND BALANCE Ifyou are searching on a ground loaded with mineralized stones or dips and holes itisrecommended to ground balance over one ofthese stones or the holes In areas of very high mineralization ground balance may not be sufficient In such a case you may need to use the mineral search modes see page 16 SENSITIVITY Sensitivity setting is used to eliminate interferences caused by electromagnetic waves in the surrounding environment or ground noise Electromagnetic waves may result from power lines in the surrounding environment or from the operation of electrical devices radars wireless radios and even TVs SENSITIVITY Sensitivity is also the depth setting for the device Therefore especially in high mineralization it is recommended that you lower it only if the device is still getting noise after you adjust all the other settings ground balance iron discrimination and mineral modes EN Velox CONTROLS IRON DISCRIMINATION IRON DISC This setting is designed for tough ground conditions and experienced users For normal ground conditions or if you do not want to bother with this setting it is recommended that you keep it at th
8. e factory setting FS This setting has 2 main purposes 1 Especially in areas of high iron mineralization and wet beach sand you may not be able to ground balance the device In such a case you can use iron discrimination By turning the iron discrimination knob to the right you can enable the ground effect to be reflected as iron and eliminate it by turning the iron switch off In general when searching in wet salt water beach sand the most ideal settings are the maximum level of the iron discrimination iron switch offand mineral 2 or 3 modes You can also use these settings when searching in wet plowed land with high iron effect 2 It enables metals containing iron to produce a low tone and to be discriminated more easily Discrimination starts at about level 4 6 Below this level all metals including iron will produce a non ferrous high tone and generally speaking the device will perform at its maximum depth In addition iron switch will not be active below this level IRON SWITCH NOKTA ENGINEERING When you want to avoid detecting ferrous metals you can turn the iron switch off and enable the device to eliminate these metals and not produce a warning tone NOTE Many metals considered to be trash may not produce a ferrous metal signal For example pull tabs may be sensed as a non ferrous metal by most detectors because their signal is very similar to that of gold CONTROLS MINERAL MODES Mineral Modes If yo
9. ion are sensed differently by a detector Oxidized metals buried under ground for a long time such as tinplates and tins may produce gold like signals Following the experienced metal detector users rule of thumb when in doubt dig is the right thing to do NOKTA ENGINEERING TECHNICAL SPECIFICATIONS Operatin Induction Balance Metal Identification Audio warninc Audio Discrimination 3 tones Sensitivity Setting Manual Ground Balance Manual Search Coil 28cm 11 waterproof Double D Battery Rechargeable Lithium Polymer Headphone Output 1 4 mono Length 125 145cm 49 57 extendable Weight 2 0kg 4 4165 including the search coil Warranty 2 years EN Velox a Emek Mah Sivatyolu Cad Sakiz Sok No 4 ee 34785 Sancaktepe Istanbul Turkey Phone 90 216 415 56 86 Fax 90 216 415 63 43 E mail info noktaengineering com
10. s and hold the i button and check the battery life indicator When the battery is full 3 LEDs will light up When only a single LED is lit it means that the battery is almost empty NOKTA ENGINEERING The battery is specifically designed for Velox One Do not use any other battery gt You must charge the battery for approximately 8 hours before first use gt When the battery is fully discharged charge it as soon as possible If you will not use the battery for a long time charge it before you store it The maximum storage time should not exceed 30 days If you will not use the battery for a longer period of time charge the battery at least once every 30 days Do not charge the battery at temperatures above 45 1137 or below 0 32 F Do not leave the battery in very hot or cold conditions Do not expose the battery to water and do not leave in very humid conditions Do not expose the battery to fire Do not throw the battery protect it from impact Do not short circuit the battery Do not use the battery if it is damaged or deformed Do not disassemble the battery DEVICE INTRODUCTION SENSITIVITY IRON DISC Mineral 2 Batter Mineral 1 Headphone Volume Speaker Input 10 GROUND BALANCE SIGNAL AUDIO VELOX CONTROLS TURNING ON THE DEVICE To turn on the device rotate the On Off knob to ON Turn the same kno
11. u are searching on high mineralized ground extremely salty soil wet beach sand wet plowed land or highly magnetic ground conditions you may not be able to ground balance the device In such a case first turn the On Off knob to mineral 1 If the device is still getting noise turn it to mineral 2 or mineral 3 This will eliminate the noise and false signals caused by mineralization However you may experience a decrease or fading in the Mineral 2 signal obtained from certain metals at maximum depths As mentioned before especially grounds with high iron content such as wet salt water beach sand and wet plowed land it is recommended that you search in mineral 2 or 3 mode bring the iron discrimination to maximum level and turn the iron switch off SIGNAL AUDIO BOOST SIGNAL AUDIO The signal audio boost switch boosts the sound of weak signals received from small or deep metals making it easier for you to detect those uncertain targets At position 1 the booster is off At 2 the signal audio will be higher and at 3 it will be heard at its maximum Please note that signal audio boost should be used on a temporary or as needed basis because it will not only boost the target signal audio but it will also boost the loudness of ground noise and false signals Therefore it is recommended to keep the switch at position 1 and turn it to position 2 or 3 only when you want to verify a weak metal signal and then turn it off again
Download Pdf Manuals
Related Search