User Manual - Weighing Scales
Contents
1. 58 18 WARRANTY INFORMATION 59 19 APPENDIX soda 60 1 page Adam Equipment Company 2010 2 page Adam Equipment Company 2010 INTRODUCTION The GFK scales provides an accurate fast and versatile general purpose weighing scales with parts counting percent weighing and check weighing functions The GFK has LEDs to indicate when a weight is below the low limit between the limits or above the high limit next to the display These can work in conjunction with an audible alarm for check weighing as well as LCD showing LO OK and HI The GFK is supplied with a RS 232 bi directional interface and real time clock RTC The GFK has a sealed keypad with colour coded membrane switches and a large easy to read liquid crystal type display LCD supplied with a backlight Includes automatic zero tracking semi automatic tare and accumulation facility that allows the weight to be stored and recalled as an accumulated total OIML Approved models GFK M do not allow pounds units have calibration controlled by jumpers or passcodes and other limitations as noted in the manual 3 page Adam Equipment Company 2010 4 page Adam Equipment Company 2010 0102 1u uudinb3 wepy sealq Z ZSM uon un 4 5181 431 YUM Sulu l Moi v2 Sununo Sulusl2. 52 Page Adam Equipment Company 2010 Apply power to the indicator If the jumper has been used the display will ask for a code number PR on the Weight Display immediately Or press the Tare key during the time the calibration counters are being displaved Enter the number 1000 when Ph is displayed and then press Tare The displays will show the first parameters called H Int To select another parameter press the Func key to advance through the parameters Press the Tare key to enter a parameter To exit a parameter press the Zero key The display will show the parameter number and a name When a parameter is entered by pressing the Tare key the displays will guide you through the parameter selected and the options available The parameters available are FA Int Initial Zero Range Fo FEZ Re Zero range F6 SCS Successive Tare Enable FT Cnt Display the A D counts F8 Zem Zero Mode F9 Lud Low voltage detection F10 Cn GK M only Calibration and Parameter counters or HO AZ Auto Zero Range 53 Page Adam Eguipment Company 2010 F4 INITIAL ZERO RANGE To enter this parameter press the Tare key when F4 int is shown The display will show the current initial zero range Press the Fune key to change the value and press Tare to accept the value Press Zero to return to weighing F5 RE ZERO RA
3. J 23 10 5 2 SETTING UP WHILE PARTS COUNTING OR WEIGHING 24 10 6 LIMITS STORING AND RECALLING 24 10 7 PERCENFWEIGHING maa aaa 26 10 8 ANIMAL DYNAMIC WEIGHING l l J 29 10 8 1 ANIMAL WEIGHING PROCEDURE 30 10 9 ACCUMULATED TOTAL uuu u a an 31 10 9 1 MANUAL ACCUMULATION J 31 10 9 2 AUTOMATIC ACCUMULATIOLN J 33 11 RS 232 SPECIFICATION D 34 11 1 INPUT COMMANDS 222555 39 12 GALIBRATION mn AABANG 40 13 PARAMETER SETTINGS sss asd oranie 41 13 1 CHECK WEIGHING PARAMETERS u 41 13 2 RS 232 5 UU U karin ada sada bz ia 44 13 3 SCALE PARAMETERS San nako ah ru nn kk 46 13 4 PERCENT WEIGHING AND ANIMAL WEIGHING 48 14 ERROR MESSAGES aaa IS ka a sas ab kin a 49 15 SERVICE A o 51 15 1 ACCESS TO 5 51 15 2 USING 1000 TO ENTER THE SERVICE PARAMETERS 52 16 REPLACEMENT PARTS AND ACCESSORIES 57 17 SERVICE INFORMATION
4. Adam Equipment offers Limited Warranty Parts and Labour for the components failed due to defects in materials or workmanship Warranty starts from the date of delivery During the warranty period should any repairs be necessary the purchaser must inform its supplier or Adam Equipment Company The company or its authorised Technician reserves the right to repair or replace the components at any of its workshops depending on the severity of the problems However any freight involved in sending the faulty units or parts to the service centre should be borne by the purchaser The warranty will cease to operate if the equipment is not returned in the original packaging and with correct documentation for a claim to be processed All claims are at the sole discretion of Adam Equipment This warranty does not cover equipment where defects or poor performance is due to misuse accidental damage exposure to radioactive or corrosive materials negligence faulty installation unauthorised modifications or attempted repair or failure to observe the requirements and recommendations as given in this User Manual Repairs carried out under the warranty does not extend the warranty period Components removed during the warranty repairs become the company property The statutory right of the purchaser is not affected by this warranty The terms of this warranty is governed by the UK law For complete details on Warranty Information see the terms and cond
5. valida solamente si een certificaat van overeenstemming accompagniato da un certificato di conformita accompagniato a un certificado da afgegeven door een bevoegde instantie relaciato da un ente riconosciuto conformidad emitida par un organismo notificado Signature Date Unterschrift Datum Signature Date 18 March 2009 Handtekening Datum Firma Date Firma S Cu m ba C S Fache 63 Page Adam Eguipment Company 2010 64 Page Adam Eguipment Company 2010 CE Manufacturer s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards following the provisions of the below stated directives Electro Magnetic Compatibility Directive 2004 108 EC Low Voltage Directive 2006 95 EC Adam Equipment Co Ltd Bond Avenue Denbigh East Milton Keynes MK1 1SW United Kingdom FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment The equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which c
6. Ay s sin 4168 BAST 91 BST 91 001 5 Sy q1 ee BAST 91 BIST 4166 AST 1Y3I9 M ION ay LEX DOEN LST JP LEX DITX LST LEX WIEX VEC UV LEXIOCX LST LEX ODER LST VLEX 9 90 X L ST ww 066 ww 0S6 ww 026 ww 066 ww 0S6 ww 066 X WW G 9 X ww 00y XWWS 9XWW X ww 26 X ww 009 x ww 9 XUU ooy x ww G 9 X ww 07 xww S 9 x ww SUOISUBUUIG cl BT XL ST el BT XL ST STE X IEC el BT X LST uL 6T X L SI el BT X LST WWP0S X WWDO WWP0S X WWDO WWH08 X UlU1009 WWP0S X WWP0S X WWDO WWP0S X ZIS Ued Sulsnou Joj Baipul Aa18 OOD sgy ued d l yog apes 1s ss ule1s aseq pajuled 18 009 uolued seq WnuiWwnle jse3 SulsnoH oouejeg 134264 Ayoedes yum UUUIGZ ejdsip u 19 yeg e dsiq qe15 s s sn sse uolleiqi eo euJ33Xx3 uone1qi e VSN 104 Jaydepe vS3 1N Vuu008 DAAZT EU UJNOS pue elsy 3doJn J u zZH09 0S IVAOEZ Ajddns Jamog 0 0 4 41 2 0 0 2 0T aJnj eJadWwa 8uneaado SIBS Z uonezijiqe1s sadJung punog s uno spunod Aeu 0 osje EXXX SLUEJBOJIM 33 SuueJO JNSEJWN JO SHUN qISTO O 39 01900 0 86 0120 3001 0110 807 ql o 0 302 4120 0 80T Ajueaul qIT0 0 37 917000 82 qIT 0 30S q g0 0 802 4120 0 301 0110 0 3s nag pis Aujgejeadsy qIS00 0 82 qIz0070 3T qI
7. HI OK LO The scale is in Check weighing mode an The colons are used to separate pounds from ounces and for the real time clock 13 Page Adam Eguipment Company 2010 Next to the LCD are a number of LED s that show when the weight is below within or over the limits during check weighing Weight LED LCD below the low limit Amber LO Within the limits Green OK Above the high limit Red HI NOTE The LED s can be set by the user to off bar spot or segment mode See F3 LED in section 13 1 The LED can be set to display as a bar increasing from Low to OK to High a single spot increasing from Low OK to High or as a single bar that changes colour as the weight progresses from Low to OK to High 6 CALIBRATION COUNTER FOR APPROVED SCALES The approved GFK M Model scales have the ability to control access to the calibration or metrology parameters using a passcode to limit access The reguirements for doing this stipulate the code should be apparent and recorded in a suitable location on the scale In this way if the record of the Calibration or Parameter counters do not agree with recorded settings the responsible person inspecting the scale can take appropriate action 14 Page Adam Eguipment Company 2010 The Counters are incremented any time the calibration section or the Factory parameters section have been modified At power on the display will show the current
8. To enter this parameter press the Tare key when F9 LWd is shown The display will show if the LVD Mode is set to on or oFF Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing F10 CALIBRATION COUNT GK M Only This parameter allows the calibration and parameter counting function to be active To enter this parameter press the Tare key when F10 Gn is shown The display will show if the Calibration Counting Mode is set to on or oFF If On the Calibration count and Parameter count will be seen at power on as described in section 6 0 If set to Off the only method that can be used for access to the calibration or parameters is to place the jumper on pins 1 2 of J1 See section 15 2 Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing 55 Page Adam Equipment Company 2010 F10 AUTO ZERO RANGE Not available on GK M This parameter set the range the autozero is active within To enter this parameter press the Tare key when F10 Az is shown The display will show the current setting 0 5d 1d 2d or 5d Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing 56 Page Adam Eguipment Company 2010 16 REPLACEMENT PARTS AND ACCESSORIES If you need to order any spare parts and accessories contact your
9. 2010 Press the 3 Lim key the check weighing mode the display will ask If you are already in if you wish to store the current limits by showing St0rE or recall another set of limits by showing FECALL The Lim key can be used to toggle between SIOrE and rECALL ECALL 0 I TTP 1 1100 P H lama N N 15 o I LL LL 110096 21 Ci JL 0 II T LTL TVT 110006 If you want to store the limits when SIOrE is displayed press the Tare key The display shows St to the desired memory location 0 to 9 St Enter a number corresponding K will be displayed for 2 seconds indicating the location X where the current limits weighing units and settings for the beeper and bar graph are stored The scale will continue to work with the current settings as active ef l 1 l ll I 110096 cb n 0 ttt ttt tt t 11006 If you wish to recall any of the pre stored Tare rECALL is displayed The display shows TEG Enter the the memory location to 9 to be recalled TEG limits press when number corresponding to desired K will be displayed for 2 seconds indicating the values stored in the location X is being recalled The scale will change to the recalled limits weighing units and settings for the beeper and bar graph 25 Page Adam Equipment Company 2010 NOTE 1 Ifthe recalled limit is for pa
10. above 15 1 USING 0000 TO ENTER THE CALIBRATION PARAMETER Pn When Pn is displayed Enter 0 0 0 0 and press Tare UnLoAd Empty the platform by removing the load if there is any and press Tare LoAd 6 KiLoS Load the requested calibration vveight and press Tarel SPAn PASS If Calibration is complete SPAn PASS will be 51 Page Adam Eguipment Company 2010 displayed Remove the calibration weight Or SPAn FAiLEd This means calibration has failed Remove the calibration weight and repeat the process JP On Remove the jumper or shorting of the pins whichever is used The scale will return to normal weighing 15 2 USING 1000 TO ENTER THE SERVICE PARAMETERS Non Approved indicators For the non approved indicator press the Tare key during the display counting when turned on Approved Indicators For the Approved version a jumper can be installed to allow access or the Calibration and Parameter Counters must be enabled see 15 2 10 Calibration Access on Approved Scales Pin 1 Pin 2 Jumper JTAG Input for programming 35 ver E DR26 pas 22 DU3 su LE m Dog DRZI See B Z um DRY 1 re 66 U1 DR mam m pReel 2 ES 5 OHEEADI buz 5 m m tz an m sm R Pos FM z a 0507 ARAB mm e 2222 M cnm Hu 2 EL M
11. disappear 10 2 2 PRESET TARE NOT AVAILABLE ON GFK M APPROVED SCALES When the scale is at zero with no weight on the platform it is possible to enter a preset tare e Zero the scale by pressing Zero The zero indicator will be on e Enter a value using the numeric keys e Press Tare to tare the scale The value that was entered is stored as the tare value and it is subtracted from the display leaving a negative number on the display 18 Page Adam Eguipment Company 2010 10 3 WEIGHING To determine the weight of a sample first tare an empty container if used then place the sample in the container The display will show the weight and the unit of weight currently in use m IG 0 IA Ett l l lll 1100 m n 2249 To change the weighing unit press the Unit key The only alternative weighing unit is pounds This can be enabled by the user in the parameters section See section 13 3 10 4 PARTS COUNTING The scale can be used to count parts based on the average weight of a sample weighed When more parts are added the total number of parts are displaved e If a container is to be used place this container on the platform before entering parts counting and press Tare e Press Cnt to enter the Parts Counting mode The display will show the last sample size used For example 10 Pcs je HE pcs 0 1 4 l I l l l l 110096 19 Page Adam Eguipment Company 2010 Either place 10 pa
12. on Prton 232 interface Prt oFF C2 hd Baud Rate 600 9600 1200 2400 4800 9600 19200 44 Page Adam Equipment Company 2010 C3 PrM Printing Mode Manual MAN m n Continuous or Automatic Cont EE scales AUto 04 Enable or disable the AC on AC on Accumulation AC oFF C5 Ln Select Language EnGli English EnGLi FrENCH French GErmAN German SPAN Spanish C6 Uld Set User ID To be entered manually 000000 C7 Sid Set Scale ID To be entered manually 000000 Scale will perform the following depending on the Accumulation and Print Settings ACCUMULATION AC on AC Off SETTINGS PRINT SETTINGS Alto Accumulate and print Print automatically automatically Do not accumulate man Accumulate and Print only Print when Print key is pressed when Print key pressed Do not accumulate Cont Print continuously Print continuously Not AS AbIE ep Accumulate when Do not accumulate approved scales Print key is pressed 45 Page Adam Eguipment Company 2010 13 3 Scale Parameters e Shortcut to enter this group is to press and hold the Count Key for 4 seconds The display will go directly to S1 Un e Press Func to view the list of parameters e Press Tare to enter a parameter Press Func to view the options for the parameter settings e Press Tare to confirm the change and then advance to the next parameter by press
13. to display the net weight This is the same as pressing Tare Z lt cr gt lt lf gt Sets the zero point for all subsequent weighing The display shows zero P lt cr gt lt lf gt Prints the results to a PC or printer using the RS 232 interface It also adds the value to the accumulation memory if the accumulation function is not set to automatic 39 Page Adam Equipment Company 2010 12 CALIBRATION The GFK scales can be calibrated using kilogram weights or using pounds weights depending on the weighing unit selected at the time of calibration To start the calibration either get into the calibration section through the Scale Settings FUME 3 see Section 13 3 or turn the scale off and switch on again then press Tare during the self test Enter code number 0000 and press Tare This will take vou directly to the calibration section The display will show UnLoAd Remove all weight from the platform and then press the Tare key when the display is stable After the Zero point is set the display will show XX Place the suggested calibration mass on the platform It is best to use a weight close to the full capacity of the scale If the mass is different from the displaved value enter the value of the mass in whole numbers The kg or the Ib symbol will be on to show the active unit Press the Tare key when the stable indicator is on The scale will calibrate to the mass When compl
14. 010 Data Format Continuous Output Normal weighing 1 234 kg lt cr gt lt lf gt Net Weight or Gross wt Data Format Continuous Output Parts Counting Net 1 234 kg lt cr gt lt lf U W 123 g lt cr gt lt lf PCS 10 pos lt cr gt lt lf lt cr gt lt lf gt lt cr gt lt lf gt Net Weight or Gross wt Kg and g for metric and Lb for pounds NOTE The accumulated total will not be sent to the RS 232 when the continuous print is turned on The continuous print will only be for the current weight and the display data In other languages the format is the same but the text will be in the language selected 37 Page Adam Equipment Company 2010 Description ENGLISH FRENCH GERMAN SPANISH Net weight Net Wt Pds Net Net Gew Pso Net Weight per unit Unit Wt Pds unit Gew Einh Pso Unid counted Number of items PCS Pcs Stek Piezas counted Number of NO Nb Anzhl Num weighing added to subtotals Total weight and Total Total Gesamt Total count printed Print date Date Date Datum Fecha Print time Time Heure Zeit Hora Scale ID number cale ID Bal n Waagen ID Bal ID User ID Number User 10 Util ID Nutzer ID Usuario ID 38 Page Adam Equipment Company 2010 11 1 INPUT COMMANDS FORMAT The scale can be controlled with the following commands Press the Enter key of the PC after each command T lt cr gt lt lf gt Tares the scale
15. EP GB1320 CE de type Corresponds to the production model described in the EC type approval certificate and to the requirements of the Council Directive 90 384 EEC as amended and to the requirements of the following EC Entspricht dem in der Bescheinigung ber die Bauartzulassung beschriebenen Baumuster sowie den Anforderungen der EG Richtlinie 90 384 EWG in der jeweils geltenden Anforderungen folgender EG Richtlinien Fassung und den Correspond au modele d crit dans le certificat approbation CE de type aux exigences de la directive 90 384 CEE modifi e et aux exigences des directives CE suivantes Directives 2006 95 EC Electrical equipment 2006 95 EC Elektrische Betriebsmittel 2006 95 EC Mat riel lectrique pour for use within certain zur Verwendung innerhalb utilisation dans des limites voltage limits Low bestimmter de tension d finies Voltage Directive Spannungsgrenzen Directive Basse Tension Niederspannungsrichtlinie 2004 108 EC Electromagnetic 2004 108 EC Elektromagnetische 2004 108 EC Compatibilit compatibility Vertr glichkeit lectromagn tique This declaration is only valid when accompanied by a Certificate of Conformity issued by a Notified Body Diese Erkl rung gilt nur in Verbindung mit einer Konformit tsbescheinigung einer benannten Stelle Cette d claration est seulement valide quand elle est accompagn e par une Attestation de Conformit d livr e par un Org
16. ER ADAM Adam Equipment GFK Series P N 9679 Revision B March 2010 Software Rev V1 17 GK H scales for Europe V2 25 EC Approved scale V3 32 GK scale for USA V4 07 GK H scale for USA V5 32 GK scales for Europe Adam Equipment Company 2010 Easy Reference Model name of the scale Serial number of the unit Software revision number Displayed when power is first turned on Date of Purchase Name of the supplier and place Adam Eguipment Company 2010 CONTENTS 1 INTRODUCTION 3 2 SPECIFICATIONS auditka do k A ah ku k A a daaa dad 5 3 INSTALLATION ma id ent kr lin k n 9 3 1 UNPACKING a ken K K anaana 9 COCATING Sr as 9 9 3 SETTING UP THE SCALES AB KA 10 4 KEYPAD EE 11 Sa DISPLAY E 13 5 1 SYMBOLS AND INDICATORS u uu nn nn 13 6 CALIBRATION COUNTER FOR APPROVED SCALES 14 Te BATTERY EEN 16 8 DBACKLIGNI SEN 16 9 AUTO POWER OFF a da ATE aa CA ac 16 10 OPERATION E 17 10 1 ZEROING va kr v v 17 10 2 LE PRE ee 17 10 2 1 MANUAL TARE oa dan EE 17 10 2 2 PRESET TARE NOT AVAILABLE ON GFK M APPROVED SCALES 18 LK WEIGHING E 19 10 4 PARTS COUNTING ka a a r 19 10 5 CHECK WEIGHING a ku kia k v 22 10 5 1 SETTING UP WHILE WEIGHING
17. NGE To enter this parameter press the Tare key when FOFEZ is shown The display will show the current re zero range Press the Func key to change the value Press Tare to accept the value Press Zero to return to weighing F6 SUCCESSIVE TARE To enter this parameter press the Tare key when F6 8697 is shown The display will show if the successive tare is on or off Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing F7 ADC COUNTS To enter this parameter press the Tare key when FI Cnt is shown This parameter allows you to view the A D counts from the internal A D converter This can be an aid to service Press the Tare key to return to the PARAMETER menu Press the Zero key to return to weighing Typical value at zero is 30 000 90 000 approx Typical value at full capacity is 500 000 approx 54 Page Adam Eguipment Company 2010 F8 ERO MODE To enter this parameter press the Tare key when ZEM is shown Select the Zero mode desired In all but special cases Zero Mode 1 is used The other 2 zero modes are for unigue locations in the world and effect the range of the zero Press the Func key to change the value Press Tare to accept the displaved value Press Zero to return to weighing F9 LOW VOLTAGE DETECTION This parameter allows detection of low voltage when the battery wears down
18. T 0 30S qiS0 0 802 d Z0 0 30T 0110 0 3s Aujgepeay qI0 3Y0ST qIS9T 362 qIOZET 5009 91099 8400 QIO E 3X0ST 1591 BASL Apede uunulxeyy HEO EM4D HES9TM4D E0ZET NID 2099 M49 2066 NID ES9T M49 HOST 345 HSL M49 009 345 00 M45 OST 319 SL M49 IBPOW S IPOW 149 SNOILV 13193dS 0102 Auedwuo 1u uudinb3 wepy 3ed 9 0102 Auedwuo 1u uudinb3 wepy aded Z ZSM uon un p oH 8e1u 5J d s1u8l G31 YUM SulysiemyIayD Suljuno SulysiaM saines 8 q1 001 5 sh q E BAST 70 ay LEX IE X IEC V LEX G 9TX LO ST ww 026 X WW SZ6 X ww 009 ww 0S6 X ww G 9 X ww QOL suolsu ul q ay LEX JU 9EX 9 ay LEX G 9TX LST 2ZIS Ued ww 026 X WW 426 X ww 009 ww 0S6 X WwW S 9 X ww NOY Sulsnou SulsnoH oue eg Joyesipul 8 002 sgy ued d l yog 8 991S ss lule3s aseq pajuled 18 1009 uolued seq WnuiWwn y 1522 134264 Ayoedes yum WWGZ Aeldsip u 19 yeg Aejdsiq qe15 s s sn SSEJA UoHeJgIEJ euJ33Xx3 uonelq leo 2 09 05 DVAOEZ Ajddns 1amod APE 0 4 7T 2 0Y 012 01 4njej dusl Sunejsdo SIIS C SIIS C SIS SOS T OU uonezilqe s Aluo 54 5 JO SPUN 8420 8410 8400 3200 Ayiqepeay 39009 3900 30ST 8409 A ioede UNLUXEN W009 M45 W008 NID INOST NID N09 M45 PPO SIOPON IN NI D 0102 Auedwuo 1u uudi
19. acklight is disabled and the battery is fully charged e When the battery needs charging a symbol on the display will turn on The battery should be charged when the symbol is on The scale will still operate for a period of time after which it will automatically switch off to protect the battery e To charge the battery simply plug into the mains power supply The scale does not need to be turned on e The battery should be charged for 12 hours for full capacity e To the right of the display is a LED to indicate the status of battery charging When the scale is plugged into the mains power the internal battery will be charged If the LED is green the battery is being charged If it is red it is nearly discharged and yellow indicates the battery is increasing the charge level Continue to charge overnight for a complete re charge 8 BACKLIGHT The backlight for the LCD can be set by the user to always off always on or automatic on only when the scale is in use or a key is pressed See setting of the parameter S2 BL in section 13 3 9 AUTO POWER OFF The auto power off can be set by the user to disable the feature or to a pre set time interval See setting of the parameter S3 AOF in section 13 3 16 Page Adam Eguipment Company 2010 10 10 1 10 2 10 2 1 OPERATION ZEROING You can press the Zero key at any time to set the zero point from which all other weighing and counting is measured This will usually b
20. ameters and press Tare to enter a parameter setting 41 Page Adam Equipment Company 2010 e Press Func to view the options for setting e Press Tare to confirm the change and then advance to the next parameter by pressing the Func key This group of parameters enables or disables the percent weighing sets the lock for re setting the check weighing limits enables or disables the check weighing LED indicator enables or disables the check weighing alarm sets the User Password for check weighing enables or disables the negative check weighing Parameter Description Options Default setting F1 Lik This parameter prevents the With LLK set to Off oFF 0FF normal user from changing the user is allowed to the limits with the help of a change limits at any Limit Lock time With LLK set to Preset PSt the user is allowed to use one of the preset limits only 42 Page Adam Eguipment Company 2010 F2 LEd This parameter sets the LED indicator to off or on and the LED type whether LED s are on in the form of a continuous bar or a spot LED or a segment of colour hr Bar type Spot Spot type Sey Segment OFF Off This Beeper to off or on f set to parameter sets the on the beeper can further be set to sound vvhen the vveighing result is vvithin or outside the check vveighing limits hP oFF off hP inl Within limits BP otL Outside limits
21. anisme Notifi Fabrikant Adam Equipment Co Produttore Adam Equipment Co Fabricante Adam Equipment Co Ltd Ltd Ltd Type GK M GFK M Modello GK M GFK M Tipo GK M GFK M Nummer van de Numaro del Verklarling van UK2860 12777 d x UK2860 certificado de UK2860 EG GB1320 Ee P GB1320 aprobacion de GB1320 typegoedkeuring tipo CE Conform met het model beschreven in de verklaring van EG typegoedkeuring en met de voorschriften van EG richtlijn 90 384 EEC zoals gewijzigd en met de volgende EG richtlijnen Conforme al modello di produzione descritto nel certificato di approvazione de tipo CE e secondo le richieste CE direttivo 90 384 CEE come modificato e secondo le rechieste della seguente directive CE Conforme al modello di producion descrito nel certificado di aprobacion del tipo CE e segun los requisitos del CE diretiva 90 384 CEE como modificato e segun los requisitos della siguiente diretive CE 2006 95 EC Laagspanning richtlijn 2006 95 EC Strumenti elettrici per uso 2006 95 EC Instrumentos electricos entro certi limiti di para uso dentro cierti voltaggio Directivo di limites del voltaje voltaggio basso Diretivo di voltaje bajo 2004 108 EC EMC richtlijn 2004 108 EC Compatibilita 2004 108 EC Compatibilidad electromagnetico electromagnetico Deze verklaring is alleen geldig samen met Questa dichiarazione e valida solamente se Esta declaracion es
22. ase the user will be required to correct the interference at his own expense Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device Changes or modifications not expressly approved by Adam Equipment could void the user s authority to operate the equipment WEEE COMPLIANCE tr Sealed Lead Acid 4 GE Battery SE Must be recycled 0 v Properly w PB Any Electrical or Electronic Equipment EEE component or assembly of parts intended to be incorporated into EEE devices as defined by European Directive 2002 95 EEC must be recycled or disposed using techniques that do not introduce hazardous substances harmful to our health or the environment as listed in Directive 2002 95 EC or amending legislation Battery disposal in Landfill Sites is more regulated since July 2002 by regulation 9 of the Landfill England and Wales Regulations 2002 and Hazardous Waste Regulations 2005 Battery recycling has become topical and the Waste Electrical and Electronic Equipment WEEE Regulations are set to impose targets for recycling Adam Equipment Company 2010 ADAM EGUIPMENT is an ISO 9001 2000 certified global company with more than 35 years experience in the production and sale of electronic weighing eguipment Adam products are predominantly designed for the Laboratory Educational Medical retail and Industrial Seg
23. cept the set values Allows the weight unit weight and count to be seen when parts counting or to change from weight to in percent weighing Adam Eguipment Company 2010 Low Limit High Limit gt Lim Func Count Print 1 to 0 and CE It sets the limits for check weighing and allows setting of either the low limit or the high limit or both It stores and recalls any of 10 preset limits This is used to select percent weighing RS 232 parameters Operation of the bar graph RTC settings User ID and Scale ID Enter Parts Counting It is used to print the results to a PC or printer using the RS 232 interface It also adds the value to the accumulation memory if the accumulation function is not automatic Allow entering numerical values where required setting of limits tare value time and date for example 12 Page None None None None None Adam Eguipment Company 2010 5 DISPLAY 5 1 SYMBOLS AND INDICATORS The LCD has unique symbols to indicate the following 20 The display is at Zero v The scale is Stable Net Net weight The scale has been tared kg Ib Symbols shown for the units Capacity Tracker A bar graph indicating the proportion of the scale capacity being used by the weight on the platform tt Low battery bAt LO or LE The scale is in Percent weighing mode pcs The scale is in Parts counting mode
24. e If you want to reset the value to zero press CE to clear the value The limits are displayed in the weighing unitin use To set the high limit press High Limit the display will show the high limit the HI symbol will be on to the left side of the display Set the high limit in the same way the low limit was set Pressing the Tare key to enter the value will return the scale to weighing with the Check weighing function enabled 23 Page Adam Equipment Company 2010 10 5 2 SETTING UP WHILE PARTS COUNTING OR WEIGHING During parts counting and percent weighing the limits are set in the same way as above The limits are displayed in pcs or See Section 10 4 for the description of parts counting and Section 10 7 for percent weighing NOTE 1 The weight must be greater than 20 scale divisions for the check weighing to operate 2 To disable the check weighing function enter zero into both the limits as described above When the current limits are shown press CE to clear the settings then press Tare to store the zero values 10 6 LIMITS STORING AND RECALLING The scale can store up to 10 sets of high and low limits in memory along with the weighing units in use including pcs for parts counting and for percent weighing as well as settings for the beeper and bar graph During Check weighing the current limits can be stored or previously stored units can be recalled 24 Page Adam Equipment Company
25. e necessary when the platform is empty When the zero point is obtained the display will show the zero indicator The scale has an automatic re zeroing function to account for minor drifting or accumulation of material on the platform However you may need to press Zero to re zero the scale if small amount of weight is still shown when the platform is empty TARING MANUAL TARE Zero the scale by pressing Zero The zero indicator will be on Place a container on the platform and its weight will be displaved Press Tare when the reading is stable The weight that was displaved is stored as the tare value and it is subtracted from the display leaving zero on the display The stable and Net indicator will be on As a product is added only the weight of the product will be shown The scale could be tared a second time if another type of product was to be 17 Page Adam Eguipment Company 2010 added to the first one Again only the weight that is added after taring will be displayed 0 l l LTL 110096 NOTE When the container is removed a negative value will be shown If the scale was tared just before removing the container this value is the gross weight of the container plus all products which were removed The zero indicator will also be on as the platform is back to the same condition it was when Zero was pressed last Press Tare or Zero to remove the tare value and display zero The Net indicator will
26. eight on the platform The beeper will sound when the scale is stable indicating the value is accepted Remove the weight e The display will show ACE 1 and then the total in the memory before it returns to zero Adding a 2nd weight will repeat the process e While the weight is on the platform press the Print key to view the values first the accumulation number ACE X and then the total will be shown NOTE 1 The scale will not show the value when a weight is removed 2 In all cases the display must return to zero or a negative number before another sample can be added to the memory 3 More products can be added and Print be pressed again for up to 99 entries until the capacity of display is exceeded 33 Page Adam Equipment Company 2010 11 RS 232 SPECIFICATION The GFK indicator is supplied with bi directional RS 232 interface as standard The scale when connected to a printer or computer outputs the weight with the selected weighing unit through the RS 232 interface Default Specifications RS 232 output of weighing data ASCII code 9600 Baud user selectable 8 data bits No Parity Connector 9 pin d sub miniature socket Pin 3 Output Pin 2 Input Pin 5 Signal Ground The scale can be set to print text in English French German or Spanish See the RS 232 parameters section for details 34 Page Adam Equipment Company 2010 Data Format Normal Output Only weight value along with
27. ence mass on the platform Err 8 High limit input error Lovv limit is set first then the high limit is set lower than the low limit and high limit not equal to zero 491Page O Adam Equipment Company 2010 Err 9 Low limit input error High limit is set first then the low limit is set higher than the high limit and low limit not equal to zero FAILH or Calibration error Improper calibration should be within 10 of the factor FAILL calibration The old calibration data will be retained until the calibration process is complete DO Page Adam Eguipment Company 2010 15 SERVICE PARAMETERS 15 1 ACCESS TO PARAMETERS APPROVED SCALES Access to the scale parameters and calibration is controlled in all approved scales either by limiting access to be after the Calibration Jumper is put on the PCB location J1 pins 1 amp 2 In this case the display will show the passcode request screen P To continue enter a passcode as described below Or if the Calibration and Parameters have been enabled the user must enter the correct password to have access See Section 6 0 Entering passcode 0000 will allow calibration as shown in 15 1 entering 1000 will allow access to a limited set of parameters as described in section 6 2 NON APPROVED SCALES Non EC Approved scales will allow entry to the parameters if the Tare key is pressed during the power on cycle The passwords work as
28. ete it will display PASS and then either display 58 GAL if entered the calibration section through the Scale Settings as per section 13 3 or return to normal weighing if entered directly Remove the calibration mass If an error message FAIL H or FAILL is shown re check the calibration and repeat If the error cannot be corrected contact your supplier 40 Page Adam Eguipment Company 2010 13 PARAMETER SETTINGS Pressing the Func key allows the user to access the parameters for customising the scale The parameters are split into 3 groups 1 Check weighing parameters 2 RS 232 parameters and 3 Scale parameters 4 Percentand Animal Weighing Functions 13 1 When Func is pressed display will first show FUME 1 for Check weighing parameters Enter 2 for RS 232 parameters or 3 for Scale parameters or 4 for percent weighing and animal weighing or press the Func key to advance through the groups Hint 1 FUnG 2 FUnG 3 and FUnG 4 Press Tare to enter the desired group of parameters Press Zero to return to the group FUNC T If vou press Zero again the scale will exit the User Parameter section and return to normal weighing CHECK WEIGHING PARAMETERS Shortcut to enter this group is to press and hold the Unit key for 4 seconds The display will go directly to FURC T Press Tare to enter the group Press Func to scroll through the par
29. gt 20d bP inl F4 CPS This setting of a new Check parameter allows weighing password must be entered twice when asked When complete it will display done To be entered manually This negative parameter enables check vveighing function vvith ability to do negative tare NOTE 1 The Check vveighing passvvord is separate from the scale passvvord see section 13 3 access to F3 FA LEd F5 F6 GPS and F7 nCK 431Page If the password is other than 0000 user must enter the password to gain O Adam Equipment Company 2010 13 2 RS 232 PARAMETERS e Shortcut to enter this group is to press and hold the Print key for 4 seconds The display will go directly to C1 on e Press Func to view the list of parameters e Press Tare to enter a parameter Press Func to view the options for the parameter settings e Press Tare to confirm the change and then advance to the next parameter by pressing the Func key Press Zero to return to the group FUNC 2 If you press Zero again the scale will exit the User Parameter section and return to weighing This group of parameters can be set by the user for setting the language baud rate printing mode etc The user can also set a Scale ID number and a User ID number Parameter Description Options Default Values or setting C1 on Enable or disable the RS Prt
30. he plastic support at the top Excess cable can be stored within the tube The GFK Series comes with a stainless steel platform packed separately Place the platform in the base Level the scale by adjusting the four feet If the scale rocks re adjust the feet Attach the indicator module to the pillar by sliding it over the bracket with the flanges engaged in the groves on the base Attach the cable from the base to the connector on the rear of the indicator Attach the power to the indicator Press the On Off key The software revision number will be displayed followed by a self test showinsg all digits before the zero is displayed along with the unit of weight that was selected last If the scale is an approved version GFK M and the Calibration Counter has been enabled see section 6 the current values will be displayed These values should match the values marked on the scale at the time of verification if it has been verified 10 Page Adam Eguipment Company 2010 KEYPAD KEYS Zero Tare Unit PRIMARY FUNCTION Sets the zero point for all subsequent weighing The display shows zero It tares the scale and stores the current weight in memory as a tare value subtracts the tare value from the weight and shows the results This is the net weight This is used to select the weighing units from a preset list of available units 11 Page SECONDARY FUNCTION Escape from any setting menus Ac
31. ing the Func key Press Zero to return to the group FUnG 8 If you press Zero again the scale will exit the User Parameter section and return to normal weighing This group of parameters are used to control the operation of the scale Parameter Description Options Default setting S1 Un Enable or disable weighing Kg kg units Not all units are g available for all scales ib settings 02 Only USA scales have Ib 0z imperial unit 2 bl Backlight set to always on EL OFF EL AU always off or automatic on El on whenever a weight is EL AU placed or a key is pressed 46 Page Adam Eguipment Company 2010 53 AoF Auto Off Disable or set SLP 0 SIP 0 time increment to turn off SLP 1 scale SIP 5 SLP 10 S4 di Set Time and Date format Enter the time 00 00 00 and settings manually mid Enter the date YY manually 55 dis Display all weights or only ALL ALL when stable 6 Filter setting to slow SLOW nor normal or fast nor FASt S1 SPS Scale Password If it is Pr lt 0000 anything other than 0000 then the user must enter the password to gain access to any of the scale parameter settings Must be entered twice when asked When complete it will display done 8 CAL Calibration Calibrate the scale See Section 10 0 47 Page Adam Equipment Company 2010 13 4 PERCENT WEIGHING AND ANIMAL WEIGHING See section 10 7 and 10 8 fo
32. is selected the display will show 100 00 Remove the 3500g weight and place a 3000g weight The display will show 85 7 as 3000g is 85 7 of 3500g VN amy L an emm g 0 141111111 1 110096 2 gt Ke number of decimal points will depend on the weight used A smaller weight will show only 100 while a larger weight might show 100 00 If the scale was showing zero weight before entering this function then the user must manually enter the weight to be set as 100 When F4 PCT is displayed enter the weight to be used for the 100 reference then press Tare to accept the reference weight The display will show 0 00 27 Page Adam Equipment Company 2010 If the scale shows XX XX which is the last weight used as a reference press CE to clear and use the numeric keypad to enter a new value Press Tare to accept the new reference weight e The weight entered must be greater than 50 scale divisions e Press Unit to return to normal weighing NOTE The display may jump by large numbers unexpectedly if small weights are used to set as 100 reference The scale checks if the weight is too small and will show Error 7 28 Page Adam Eguipment Company 2010 10 8 ANIMAL DYNAMIC WEIGHING The scale can be set to animal dynamic weighing for weighing any items that are unstable or may move See Section 13 4 The scale will use a special fi
33. itions of sale available on our web site 59 Page Adam Eguipment Company 2010 0102 Auedwo 1u uudinb3 wepy 5 13 OL 8 5 TANA 1U IOM 96001 J91UJ BUIU IOM jewiuy luy ri Su u8SI AA 14 2 4 Pd Pi UOIJEJGI EI WJojJad shay m wnu Suen Jeu 1SV4i euuJou jou MO1S lqe1s uaym qvis liv jenuew Ul p qlos p se yas OT d1S S d1S T dis 0 dis ony ny 14 uo 13 440 14 qi 3 TVI 8S piomssed e5S Sds LS 19114 195 14 9S apow e dsiq SIP SS pue uun P S Ip tS unu awl HO ony PS JOV ES IyBipeg 14 25 lqeu spun un TS 3ed 09 shay 3u unu 3ulsn iu lu3 sha 3u unu 3ulsn iu lu3 usiueds 2 4533 440 uo onewojny ony snonul1U02 1uo2 jenuew uyw 00261 OL 009 330 Hd uo 14 GI le5s PIS 22 q 4asn pin 99 sululid Joj o8en3ue1 U 62 uonernun oy qeu3 uoy EI apo 8ullulid Wd CH ajey pneg pq ZI CEC SU lqeuq uo T HO Sury3iam yay aMje3aN uo YIN SI piomssed poujoW BulyBiam y3IBYI 3u umu 3ulsn Jeu Sd 4 sun pisino no dq swing pisul jui dq 011U03 Jadaag 440 dq 434 23 nu ui8 s ajoum V3dS 9dA1 1005 yods ejdsip q31 d 1eg 1vq 23 19s o1d 154 907 1 440 XTI T4 slajaweleg 2 t INNI sJajaweled e5S INNA sdaya
34. lter to minimise the effects of any movement on the platform Press Func The first option is FUnG 1 press the Func key 3 more times to display Fune 4 ot H o IA EP I l I lI I I 110056 Press the Tare key F4 PE will be displayed Press the Func key to advance to the second function FA Anl Animal weighing Fu Anl 0 LA Ett l l l l I 1100 e Press Tare to enter the animal weighing function e To use the Animal Weighing function it is necessary to set the amount of filtering required for the animals to be weighed More active animals will require a higher level of filtering to give a stable result The display will show H LL where x is a value from 1 to 5 The higher the value the greater the amount of filter will be To increment the value shown press the Func key then press the Tare key to accept it e The display will flash Ani 2 times then show the current weight 0 00 The scale is now ready to weigh 29 Page Adam Eguipment Company 2010 10 8 1 ANIMAL WEIGHING PROCEDURE With the platform empty the display will show zero weight Place containers or blankets onto the platform and press the Tare key to zero the display The scale may go into the animal weighing procedure when the items are placed on the scale but will return to showing zero when the Tare key is pressed e Place the animal to be weighed on the platform The display will sh
35. ments The product range can be described as follows Analytical and Precision Balances Compact and Portable Balances High Capacity Balances Moisture analysers balances Mechanical Scales Counting Scales Digital Weighing Check weighing Scales High performance Platform Scales Crane scales Medical Scales Retail Scales for Price computing For a complete listing of all Adam products visit our website at www adameguipment com Copyright by Adam Equipment Co Ltd All rights reserved No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Adam Eguipment Adam Eguipment reserves the right to make changes to the technology features specifications and design of the equipment without notice All information contained within this publication is to the best of our knowledge timely complete and accurate when issued However we are not responsible for misinterpretations which may result from the reading of this material The latest version of this publication can be found on our Website www adameguipment com Adam Eguipment Company 2010
36. nb3 wepy 3ed 9 3 INSTALLATION 3 1 UNPACKING The GFK scales have already been adjusted to work with a platform and have been configured for this application The platform and indicator have been calibrated as a pair and must be used together 3 2 LOCATING ZE e The scales should not be placed in a location that will reduce the accuracy e Avoid extremes of temperature Do not place in direct sunlight or near air conditioning vents e Avoid unsuitable tables The table or floor must be rigid and not vibrate T T mi e Avoid unstable power sources Do not use near large users of electricity such as vvelding equipment or large motors 1 Avoid high humidity that might cause condensation t a Do not place near vibrating machinery 4 Avoid direct contact with water Do not spray or immerse the scales in water e Avoid air movement such as from fans or opening doors Do not place near open windows or air conditioning vents e Keep the scales clean Do not stack material on the scales when they are not in use 9 Page Adam Equipment Company 2010 3 3 SETTING UP THE SCALES The pillar is attached to the base using a bracket that must be attached to the base frame first using the 4 bolts supplied The pillar is secured to the bracket using 2 sets of screws The cable from the base to the indicator module is run through the tube and taken out through t
37. ow Ani until a stable weight is determined The time it takes for the stable value will depend upon the setting of the filter parameter in the first step e When a stable reading is found the display will show this value and the display will be locked until the Unit key is pressed The display will show the Hold symbol while the display is locked Remove the animal the display will hold the weight value e To weigh a second animal press the Tare key if necessary to zero the display and place the next animal on the scale It is also possible to simply place the next animal on the scale without clearing the last value first The scale will detect the new weight and hold it as before e The scale will remain in the animal weighing mode until the Zero key is pressed Then it will return to normal weighing 30 Page Adam Equipment Company 2010 10 9 ACCUMULATED TOTAL The scale can be set to accumulate when a weight is added to the scale automatically or manually by pressing Print See Section 13 2 NOTE 1 The accumulation function is available only during weighing It is disabled during parts counting or percent weighing 2 The accumulated weights will be stored in either kg or Ib depending upon the weighing unitin use 3 If at any time the weighing units are changed the accumulated data will be lost 10 9 1 MANUAL ACCUMULATION When the scale is set to manual accumulation the weight displayed will be
38. r a new sample size as above To return to weighing press Unit when nes is displayed 21 Page Adam Equipment Company 2010 10 5 CHECK WEIGHING Check weighing is a procedure to display an indicator or sound an alarm when the weight on the platform meets or exceeds the values stored in the memory The memory holds values for a high limit and a low limit Either or both the limits can be set by the user NOTE 1 The alarm and the LED bargraph can each be set to OFF See section 13 1 The LCD display will indicate whenever the weight is within or exceeds the limits by showing HP or 10 f Mass on the platform is above the high limit OK Mass is between the limits LO Mass is below the low limit 2 The limits can be locked by the manager A Limit Password must be used to change the limits or recall other limits from memory 3 If Limit Password is enabled then enter the password which will allow you to change the limits or the operation of the beeper or bargraph 22 Page Adam Eguipment Company 2010 10 5 1 SETTING UP WHILE WEIGHING Press the Low Limit key It will show the current low limit The LO symbol will appear on the display Press the CE key to clear the old value and then enter the new low limit using the numeric keys The decimal point is fixed at the position that is used for the current weighing unit When the desired value is shown press Tare to accept the valu
39. r details of these special weighing modes Parameter Description Options Default setting F4 PCt This parameter allows the None Enabled user to enter the Percent always weighing Function See Section 10 7 H Mi Enter the Animal Weighing Set the filter value Enabled mode of operation See Alvvays section 10 8 481Page O Adam Equipment Company 2010 14 ERROR MESSAGES During the initial power on testing or during operation the scale may show an error message The meaning of the error messages is described below Ifan error message is shown repeat the step that caused the message If the error message is still shown then contact your dealer for support ERROR DESCRIPTION POSSIBLE CAUSES CODE Err 1 Time input Error Invalid time entry such as 268910 for the time format H m Err 2 Date input Error 34th day of a month is an invalid entry Err 4 Initial Zero is greater than Weight on the platform when turning allowed 4 of maximum the scale on capacit when power is pacity Excessive weight on the platform turned on or when the when zeroing the scale Zero Enter key is pressed Platform is not installed Improper calibration of the scale Damaged load cell Damaged Electronics Err 6 A D count is not correct Load cellis damaged when turning the scale on Electronics is damaged Er Percent input error Percent function is entered vvith no refer
40. rts counting the display will show the last sample value used ready for a new sample to be counted 2 If the recalled unit is a percent weighing limit the display will show the last sample value used ready for a new sample to be weighed 3 Ifthe memory location was empty the scale will return to weighing 10 7 PERCENT WEIGHING The scale can be set to perform percent weighing See Section 13 1 The scale will use a mass on the platform as the 100 reference weight If the platform is empty or the scale is tared then the user can input a reference weight using the keypad e f using a reference weight or object as your 100 reference add the weight to the to the platform Press Func The first option is Hint T press the Func key 3 more times to Flal 5 display F nt 4 Press the Tare key F4 PUL will be displayed FY PCE we MA L L T Lam 26 Page Adam Equipment Company 2010 Press Tare again to enter percent weighing The scale will set the sample mass on the platform as 100 reference weight NOTE If there is no reference weight on the platform and percent weighing function is entered pressing Tare again will return the indicator to normal weighing Remove the sample weight Then any other weight placed on the scale will be displayed as a percentage of the original sample For example if 3500g is placed on the scale and percent weighing
41. rts on the platform for determining the average piece weight or use a different number of parts For example place 20 parts on the platform press ICE to clear the last values and then enter the value 20 using the numeric keypad W Baba d pcs 0 Il 1 I l l l l l 1100 Press Cnt to weigh the samples and determine an average piece weight If the parts are too light to measure accurately the count may become faulty It is suggested that the samples to be weighed should each weigh more than the resolution of the scale After the sample has been weighed the scale will count any other parts added by applying the average piece weight to the weight of the parts to be counted m 0 Il DU l ll ll l 1100 The Tare key works normally during this time so it is possible to tare the display with a container on the platform or to enter a preset tare value as described in section 10 2 2 During parts counting the display can be changed to show the net weight unit weight and number of parts by each time pressing the Func key 20 Page Adam Equipment Company 2010 02249 0 IA l l l l l l l 1100 gt Tax g pcs 5 1 1U3 mi 0 11010101111 1 110096 LIZ m 0 1 4 TE l l 110026 e To count a different sample quantity press the Count key The display will show the last used sample size Either use this sample size with a different part or ente
42. software revision number followed by the message of the Calibration Count IALInt then a number i e 123 The number from the counter memory Then the Parameter Counter message of PArint and probably a different number i e 234 The counters cannot be reset to 0 they will increment until the display can no longer hold the values 1 to 999999 It is expected we will never have more than 1 million calibrations in the life of the machine Each display is held for 1 2 seconds The scale will then continue to do the display test and go to normal weighing If during the time the counting displays are shown the user presses the Tare key the user will be given a message to enter the passcode necessary to calibrate the scale P Enter the code P0000 to Enter calibration or P1000 to enter the parameters followed by pressing the Tare key The Calibration access will allow user calibration See section 15 1 and the parameter code will allow access to the following parameters see section 15 2 Hin Initial Zero Range Fo FEZ Re Zero range F6 SCS Successive Tare Enable FI Un Display ADC counts F8 Zem Zero Mode F9 Lud Low voltage detection 15 Page Adam Eguipment Company 2010 7 BATTERY e The scales can be operated from the rechargeable battery if desired The GFK scales have up to 70 hours battery life before needing to be recharged if the b
43. stored in the memory when the Print key is pressed and the weight is stable e Remove the weight and press Print when the scale is at zero The display will show AGC 1 and then the weight in memory for 2 seconds before returning to normal The weight can be output to a printer or PC using the RS 232 interface SACL I 0 J PE ttt ttt 1100 0 H L 110096 sj 31 Page Adam Equipment Company 2010 e When the scale is at zero place a second weight on the platform When stable press Print to accumulate the weight The display will show ACC 2 for 2 seconds and then show the new total AL C Na _ 0 4 111 1 111 1100 P III 0 IA l l l l l l 1100X 2 v 9110 0 Continue until all weights have been added This continue for to 99 entries until the capacity of display is exceeded e To view the total in memory press the Print key when the scale is at zero The display will show the total number of accumulation ACC XX and the total weight before returning to zero e To print the total press Print to recall and then immediately press Print the second time to print the results e To erase the memory press Print to view the total and then immediately press CE to clear the memory 32 Page Adam Equipment Company 2010 10 9 2 AUTOMATIC ACCUMULATION When the scale has been set to Automatic Accumulation the value is stored in memory automatically e Place a w
44. supplier or Adam Equipment A partial list of such items is as follows e Main Power cord or adaptor for e Stainless Steel Pan USA versions In use cover e Replacement Battery e Printer etc 57 Page Adam Equipment Company 2010 17 SERVICE INFORMATION This manual covers the details of operation If you have a problem with the scale that is not directly addressed by this manual then contact your supplier for assistance In order to provide further assistance the supplier will need the following information which should be kept ready A Details of your company Name of your company Contact person s name Contact telephone e mail fax or any other methods B Details of the unit purchased This part of information should always be available for any future correspondence We suggest you to fill in this form as soon as the unit is received and keep a print out in your record for ready reference Model name ofthe scale GFK Serial number of the unit Software revision number Displayed when power is first turned on Date of Purchase Name of the supplier and place C Brief description of the problem Include any recent history of the unit For example Has it been working since i s delivered Has it been in contact with water Damaged from a fire Electrical Storms in the area Dropped on the floor etc 58 Page Adam Eguipment Company 2010 18 WARRANTY INFORMATION
45. the weighing unit is printed If Percent weighing is used then is shown in place of weighing units lt cr gt lt 11 lt cr gt lt 11 Date Time lt cr gt lt lf gt Scale ID User ID lt cr gt lt lf gt Net Wt 12 09 2006 lt cr gt lt 11 14 56 27 123456 234567 lt cr gt lt 11 lt cr gt lt 11 lt cr gt lt 11 lt cr gt lt lf If ID is zero it is left blank 1 234 kg Net Wt or Gross Wt lt cr gt lt 11 lt cr gt lt 11 lt cr gt lt 11 lt cr gt lt 11 rh Ph M Eh V V V NV Data Format Parts Counting Output Weight Unit weight and number of parts are printed lt cr gt lt li lt cr gt lt li Date 12 09 2006 lt cr gt lt li Time 14 56 27 lt cr gt lt 11 lt cr gt lt l gt Scale ID User ID lt cr gt lt lf gt Net Wt 1 234 kg Unit Wt 123 g PCS 10 pcs lt cr gt lt li lt cr gt lt li 123456 234567 lt cr gt lt li lt cr gt lt li Net Wt or Gross Wt for metric and Ib for pounds lt cr gt lt li lt r gt lt 11 lt cr gt lt 11 gt gt 35 Page Adam Equipment Company 2010 Data Format Memory Recall Output 12 09 2006 lt cr gt lt 14 56 27 lt cr gt lt 123456 lt cr gt lt 1f gt 234567 lt cr gt lt 1 lt cr gt lt 1f gt 5 lt cr gt lt 1 1 234 kg lt cr gt lt l 10 pcs lt cr gt lt 1 lt cr gt lt 1f gt 36 Page Adam Equipment Company 2
46. uesed ZEZ SY Z3NN4 saojouuejed Su u8I A YAY TINNA 8Uuly31aM 0 UJNIAJ JO Ja aweJed snojaajd o uin1 i 0137 uondo Jo Jajaweded eau o aAOW dung sodueu ay 1d 2o2e JO Ja aweded e Jajua 1e 1 5 SIY U lluM suonoun Aay pouu suon un4 Jajua A y Jung ay ssoJd SITVIS NID MD 40 LNOAVI YILIWVYVd XIGONIddV 6L 0102 Auedwuo 1u uudinb3 wepy s3eal19 62 Page Adam Equipment Company 2010 HEZADAM Adam Equlpment ADAM EGUIPMENT BOND AVENUE DENBIGH EAST INDUSTRIAL ESTATE Tel 01908 274545 Intl Tel MILTON KEYNES MK1 1SW U K 44 1908 274545 Fax 01908 641339 Intl Fax 44 1908 641339 E Mail Address info Adamequipment co uk C Declaration of Conformity Konformit tserkl rung D claration de Conformit Verklaring van overeenstemming Dichiarazione di Conformita Declaraci n de Conformidad The non automatic weighing instrument Die nicht automatischen Wageapparate L instrument de pesage fonctionnement automatique Het niet automatische weegwerktuig Strumento per pesatura non automatico Imstrumento para pesaje non automatico Manufacturer Adam Eguipment Co Hersteller Adam Eguipment Co Fabricant dam Eguipment Co Ltd Ltd Ltd Type GK M GFK M Typ GK M GFK M Type GK M GFK M No of the EC s type approval UK2860 5 unu 2 UK2860 PA UK2860 certificate GB1320 HE GB1320
Download Pdf Manuals
Related Search