DW 9000 SERIES BASS DRUM PEDALS
Contents
1. the linkage to the desired position then retighten the set screws Set the linkage memory lock to Double Pedal Linkage Adjustment maintain the desired distance every time you set up Pi ee e Y ae e e as Auxiliary Pedal Double Pedal Linkage Primary Pedal Beater Shaft Beater Position Screw Beater Memory Lock Delta Plus Rocker Stroke Adjustment Spring Tri Pivot Toe Clamp Spring Tension Adjustment Spur 2 4 Weight optional The adjustable beater weight can be positioned on the beater shaft to increase the power of the stroke Experiment to find the optimum feel and secure the weight using the standard drum key set screw Section 3 Slotted Stroke Adjustment To modify the distance the beater travels during the course of each stroke 1 Hold the beater ball with one hand and align the hex head of the stroke adjustment screw with the access hole in the right upright post 2 Using the other hand place the long hex of the 3 way drum key through the hole in the upright post and into the beater adjusting screw 3 Loosen the screw and move the beater ball to the desired position while keeping the key in the screw then retighten remove key and release Section 4 Spring Tension Adjustment DW Drum Pedal Springs feature an internal noise reduction damper as well as a tension locking mechanism To increase or decrease the spring tension 1 Loosen the round knurled nut at the base of the spring ass2. Slide the memory lock down the shaft so that it fits into the notches on the beater hub 3 Adjust the beater to the desired playing position and tighten the drum key screw on the beater hub as well as the set screw on the memory lock with the small allen wrench provided The beater ball should be positioned at a right angle to the memory lock so that the beater can be reversed from the soft felt to the hard plastic side by slightly raising the beater and rotating it 180 degrees 2 3 Playing Surface The 101 Two Way Beater standard has both a curved medium felt side for a rounder warmer attack and a flat hard plastic side for a sharper brighter attack much like wood but lighter in weight Two Way Beater Floating Rotor Footboard Angle Double Chain T T TENS Adjustment Screw Floating Drive Shaft EZ Adjust Infinite Cam Footboard a a a x E o F an a oe ca oe arte wo Hoop Clamp ____ Adjustment Non Skid Rubber Grip Delta II Bearing Hinge Pa Heel Casting Use the provided 3 Way key or any standard drum key to secure the linkage to the primary pedal by tightening the key screw Rotate the beater casting and hex shaft on the auxiliary pedal to the correct playing position attach the linkage and tighten the auxiliary side key screw Loosen the two sets of key screws on the middle section of the linkage and adjust the length and angle of
3. you may first need to heat them with a hair dryer for 2 3 minutes a Wi 44 h ue D r a e i b DW 9000 SERIES BASS DRUM PEDAL ACCESSORIES SM101 Two Way Bass Drum Beater SM102 Large Felt Bass Drum Beater EPped wna sseq jqno C006 SM103 Medium Felt Bass Drum Beater PDd WNIGd sseq olsul SM104 Solid Maple Wood Bass Drum Beater P d a d S 0006 SM105 NEW HardCore Bass Drum Beater SM808 5 Key pack includes standard large keychain drill bit and speed keys SM809 9000 Pedal 3 Way Key SM1207 Delta Hinge SMSVKIT _Drummer s Survival Kit includes plastic case Jw T hanks for purchasing this DW product It has been designed and lA NH Gi s svg manufactured to provide a lifetime of trouble free service Please take a moment to familiarize yourself with the exclusive features and operating suggestions contained in this manual in order to S i p S O O o 6 MC ensure its optimum performance Should you have any further ques tions feel free to contact your local authorized DW dealer 4 ie amp i aa SG A i sAN es SMSVKIT A A al Don Lombardi Ve gt TV NN VW S YaAN A OO Founder Dr umWorkshop Inc iby DWSM808 W a 2 Ng i Fr 7 7 i 103 104 101 102 105 DW PEDALS 5 YEAR LIMITED WARRANTY For a period of five years from the date of purchase Drum Workshop Inc gur
4. DW 9000 SERIES BASS DRUM PEDALS Remove the pedal accessories and all packing materials from the box and or case then follow these instructions to set up and adjust your pedal to fit the way you play Section Drive System Adjustments Note For a more relaxed floating pedal feel replace the standard Double Chain Drive with the optional Nylon Strap Drive included 1 Remove the chain assembly by loosening the Footboard Angle Adjustment Screw on the top of Rotor using the drum key end of the 9000 3 Way key and the connecting screw and nut at the front end of the footboard using a Phillips head screw driver and a wrench 2 Attach the nylon strap to the footboard by aligning the end of the strap that has a single hole with the screw hole in the footboard and then replacing and tightening the connecting screw and nut 3 Connect the three hole end of the strap to the captive nut in the adjustment channel on the Rotor using the drum key screw provided 1 1 Torque Your pedal is factory set to the most popular settings including the standard eccentric Accelerator torque position However the 9000 Drive can be adjusted to a variety of torque positions Choosing l an eccentric setting creates an in direct relationship between the beater and footboard increasing the velocity of the pedal by shortening the length of the stroke and is recommended for situations that require increased speed and sensitivity A more concentric
5. Turbo setting maintains a direct relationship between the sprocket and the footboard to provide a solid powerful consistent feel and is suggested for general purpose playing situations To adjust the torque to achieve your desired feel 1 Locate the EZ adjust infinite cam adjustment key screw 2 Using a drum key turn the EZ adjust key screw With this adjustment you will change the shape of the CAM to represent a range from accelerator to turbo settings 1 2 Footboard Angle To change the footboard height and angle loosen the adjusting key screw on the top of the Rotor and slide the chain or strap forward or backward to achieve the desired footboard height Then tighten the adjusting key screw This adjustment can be used to compensate for changes made by adjusting the torque or to independently modify the footboard angle to a more comfortable position Torque position adjustments from eccentric far left to concentric far right Section 2 Beater Ball Adjustments 2 1 Height The length of the beater rod can be adjusted to achieve the desired feel and impact position Loosen the beater position screw and raise or lower the beater rod to the desired position and then tighten the screw Generally the beater should hit the center of the drum or an area 1 2 inches above the center 2 2 Memory Lock 1 Place the beater memory lock loosely on the beater shaft and place the beater shaft in anormal playing position in the beater hub 2
6. antees the original owner when presented with proof of purchase that all 9000 5000 3000 and 2000 Bass Drum Pedal cast parts are free of material and manufacturing defects This warranty is limited to cast parts only such as the base casting footboard beater hub sprocket heel and cam casting This warranty does not include moving parts such as the spring assembly beater ball radius rod hex shaft ball bearings etc If under normal playing DRUM WORKSHOP INC conditions parts covered in this limited five year 4 warranty fail they will be replaced at no charge 3450 Lunar Court Oxnard CA 93030 USA Return the pedal to your authorized DW dealer or if www dwdrums com there is not a dealer in your area contact DW direct specifications subject to change without notice DO NOT send pedal to DW without first PEERAA Return Authorization Number Shipping Charges to Contact your authorized DW dealer DW will be paid by the consumer for additional accessories and replacement parts The Drummer s Choice
7. embly 2 Push down on the spring to release the self locking hex nut 3 Tighten or loosen the lock nut to the create the desired tension then release the hex nut and retighten knurled nut to lock in the adjustment Section 5 Hoop Clamp Adjustments The DW Tri Pivot Toe clamp is designed to fit a wide variety of manufacturer s bass drum hoops lo set the space of the hoop clamp for your bass drum 1 Rotate the wing screw on your hoop clamp adjustment to narrow or widen the gap 2 Position the pedal on the center of the hoop and tighten the wing saew Use the provided rubber hoop protector to avoid damage to your bass drum hoop Section 6 Toe Stop Non Skid Spurs and Non Skid Rubber Grip To install the optional toe stop 1 Remove the screw and nut at the front end of the footboard using a phillips head screwdriver and a wrench 2 Align the hole in the toe stop with the hole in the footboard and replace and tighten the connecting screw and nut 9000 DW Bass Drum Pedals include built in adjustable spurs and non skid RubberGrip on the bottom of the pedal plates to prevent bass drum crawl To adjust the spurs simply turn the knurled portion clockwise for more skid control or counter clockwise for less Be careful when you use the spurs as the may damage the floor Note Some of the screws on the pedal have been treated with a chemical lock to prevent unwanted loosening during playing In order to loosen the chemical lock holding these screws
Download Pdf Manuals
Related Search