User Manual
Contents
1. e The used mains voltage has to be the same as the stated mains voltage on the type plate of the transfer press e Watch out not to damage the power plug e If you connect the transfer press over an extension cable please make sure that the overall nominal current of all connected equipment does not exceed the allowed current load Further make sure that the overall nominal 12 SM 54 current of all connected equipment does not exceed the allowed power supply of the connected electrical outlet e Never try to maintenance the device on your own e To ensure safe operations of the transfer press the operator has to make sure that non authorized people neither work on the machine nor set the machine into operation or perform any other operations on the machine e All operations on the transfer press can only be accomplished by specialised staff who gained an appropriate instruction or training e General legal and other binding regulations for accident prevention and environmental protection are to be considered in addition to this instruction manual 1 3 Working with the Transfer Press e Look out not to touch the lower part of the heat element while the press is in service otherwise burns may occur Please also note that there is still a danger to suffer burns even after turning off the transfer press for a longer time e The case of the heat element will also be heating up so be careful e During2. push the pressure regulator back in to set the pressure Usual values for sublimation prints 3 5 bar A Maximum allowed pressure 6 bar 4 3 Time and Temperature Controller Definition Pos button temperature button time button to the right button upwards Light emitting diode heating Light emitting diode O K Display temperature een Display time 14 SM 54 4 3 1 Set Temperature 1 To set the temperature push the button temperature once the first cypher will start flashing 2 Adjust the desired value with the upwards button 3 To change the value of the second cypher push the button to the right and the second cypher will start flashing Use the same procedure to adjust the value 4 To change the third cypher use the same process like for the second cypher 5 Push the button temperature to save the settings as well as to leave the adjustment mode The light emitting diode will flash heating as long as the temperature set point is not reached yet After heating up the light emitting diode will flash O K after the transfer press reached the desired temperature Recommended temperature values 180 200 C 4 3 2 Set Printing Time Two different printing times can be adjusted 1 Push the button time and hold it In the display time lower display t1 1 time set point an
3. AA E 16 C Dil ee ee ee E E 17 The SCHUSTER Transferpressen GmbH takes no responsibility for damages arising from misuse reparations and modifications which where carried out by third not authorized parties as well as for damages arising from non observance of the instruction manual This handbook was constructed with great care a liability for small negligent mistakes for example printing error however are excluded The SCHUSTER Transferpressen GmbH takes no responsibility for damages or errors which arise from the use of accessory or spare parts which are not original pdeviceucts of SCHUSTER Transferpressen GmbH Below SCHUSTER Transferpressen GmbH is identified as the manufacturer Copyright 2010 SCHUSTER Transferpressen GmbH All rights reserved 10 SM 54 ENGLISH Abb 1 Vorderansicht SM 54 Abb 2 R ckansicht SM 54 Schlie hebel Maschinenkopf Schwenkhebel _ A ae i Heizplatte Instrumentengeh use Arbeitsplatte Klemmoriff Kurbel zur Hohenverstellung Abb 3 Zusammenbau der SM 54 Transport Sicherungsschraube Schraube M6x12 Scheibe l l Gummipuffer Scheiben Schlie hebel Schraube M6x18 Scheibe St tzfu Abb 4 Instrumentengeh use Heizplatten Stecker Hauptschalter Zeit amp Temperatursteuerung Sicherungshalter 11 ENGLISH 1 Safety Advice Read through following advices before bringing the transfer press into service It is necessary to consider a
4. is especially unacceptable to lift the transfer press at the et ET A sliding table or at the heat element When you en assemble the transport devices make sure you plumb in the fixing screws tightly 4 Settings 4 1 Height Adjustment for Work Plate 4 Remove the corrugated head screws on the sliding table Keep these as well for a further transport to secure the sliding table against slipping 1 The first step will be to loose the locking of the height adjustments To do so turn the clip handle to the left 2 Now turn the work plate in clockwise direction to lower it or in anticlockwise direction to raise it 3 When you reached your desired height turn the clip handle to the right to lock the height adjustment The gap between the undersurface of the heat element and the upper surface of the article to be printed on should be 15 25 mm Is the gap bigger higher than 25 mm the transfer press will automatically cancel the printing process for technical reasons and the heat element will go back into its original position A 4 2 Set Pressure You can adjust the pressure with the pressure regulator the manometer in the control panel serves as a control for your changes 13 ENGLISH The first step to change the pressure will be to pull out the pressure regulator then turn the pressure regulator to the right to increase the pressure to the left to reduce it After you adjusted the desired pressure
5. the service of the press and especially during the start of the transfer press never put your hand between the work plate and the heat element or the transfer press Furthermore make sure that no other person can reach the transfer press 2 Check Shipment SM 54 with a single with a double sliding table sliding table 1 x silicone foam pad 2 x silicone foam pads 1x 1x protective cover cover 2x 2x protective cover cover 1x _ wrench 1x en wrench button button 1 x instruction manual 1 x instruction manual SM 54 3 Assembling and Bringing Into Service L 2 A Unpack the transfer press Bring the transfer press to it s location of service Only use the assembled transport device to move the press Make sure that no flammable or heat sensitive materials or equipment are in immediate vicinity of the transfer press ENGLISH 5 Connect the power plug with an electrical outlet and connect the compressed air pipe to the compressed air filter see page 11 Fig 2 and 4 6 Switch on the power switch to start the transfer press 7 The transfer press will be ready for operations now 3 Remove the transport device It s very important to keep them because the transfer press can ONLY be moved through these transport devices In particular faults which will appear when trying to lift the transfer press up on other parts than the transfer devices will be exempted from this warranty It
6. SCHUSTER TRANSFERPRESSEN S Series SM 54 Instruction Manual MANUFACTURER DISTRIBUTER SCHUSTER Transferpressen GmbH Fritz Reichle Ring 20 Colour 78315 Radolfzell Components GERMANY We re about ink and tts application FON 49 7732 30279 10 Tel 1300 196 156 FAX 49 7732 30279 13 Email mail colourcomponents com au E MAIL kontakt schuster transferpressen de Street 24 25 Ingleston Road Tingalpa QLD 4173 Australia WEB www schuster transferpressen de Web www colourcomponents com au Ss LA en 1300 196 156 www colourcomponents com au S Series ENGLISH SM 54 Instruction Manual EE Advent 12 LE Mino on Bien ee are 12 122 Important security Avira REE 12 1 3 Working with the Transfer Press en ee 12 De COMI SINT 0101 05 E E E AE E A A A E AN AE E A A HE ESUREEINEEEUR 13 3 Assembling and Bringino miO Serve essiens nn ea an ea 13 ee NN ote cet PALIN re cee ec patie seins hee AIR oie cc SEHE SR E A S E A FREUE ecto Gang ER eames 13 4 1 Height Adjustment for Work Plate nennen aaa a ne 13 SCN SC ee ee E een een en 14 4 3 Time and Temperatur Controller een in 14 Aa SEIT DIR ee Eee 14 23 2 SL Poinl ne Kine see era 14 5 Pannie Opera On 2 ee ee ee nee ee 15 6 Exchange Heat Element and Work Plate u nennen 15 6 1 Bund mn and Extenda Heat Elementerne ne E E 15 02 Build mand Extend 2 Work Plat ans ee u EEEE EEEE tela NEEN Ea 15 T ME a E E AA 16 Be PUSAN EE EAE A E eee E one wea A E EAE E E E OAA
7. d t2 2 time set point will flash for about one second each 2 To adjust the desired time set point Release the button time when your desired time set point tl or t2 is flashing up in the display Now only the first cypher should be flashing 3 Set the desired value with the button upwards 4 To change the second and third cypher push the button to the right It will flash up Set the value like you did with the first cypher If you push the button time settings will be saved and you will leave the adjustment mode 0 399 sec 0 60 sec Acceptable values 1 time set point 2 time set point Usual printing time 45 70 sec SM 54 5 Printing Operation After you adjusted your settings and the temperature was reached the light emitting diode O K will flash you can begin with your printing operations L pA If you have an SM 54 pull the sliding table out If you have a pull the double sliding table to the left or right until it blocks Arrange the item and the corresponding artwork on the work plate If you have an SM 54 push the sliding table back into the transfer press until it blocks If you have a pull the double sliding table towards the opposite side until it blocks Confirm both starter buttons and the same time The heat element will lower and start the operation After the printing time is over the heat element will rise automatica
8. e clearance max 25 the heat element lowers but returns gap between heat element and mm Ch 4 1 immediately into is original work plate is too big position Work plate is twisting Height is not adjusted or Arrange the work plate and lock the right insufficient locked in place height adjustment through turning the clip handle to the right until the work plate is not twistable anymore Ch 4 1 16 SM 54 9 Technical Data External Dimensions L x W x H Weight Voltage Max current consumption Max heating power Temperature Time of pressure Max pressure Max pressure at 6 bar Max surface pressure at 6 bar on a pressure surface of 40 x 50 cm Max height of the article to be printed on ENGLISH o BE 2000 W Up to 210 C 1 time domain 0 399 sec 2 time domain 0 60 sec 17 kN 42 1 7t 8 7 N cm 17
9. ll warnings and advices indicated on the transfer press 1 1 Manual Convention A You can find this symbol in particular on important safety advices in this instruction manual in which you will be advised about the right handling of the transfer press It is necessary to pay attention to these advices Non observance can lead to injuries of the user Security advices which are marked with this symbol it s necessary to pay attention to In case of non observance burns of the user may occur You also can find this symbol marked on some parts on the transfer press A symbol like this advices you that through crushing danger of injuries exists You also can find this symbol marked on parts of the transfer press 1 2 Important Security Advices This transfer press presents dangers if used inappropriately or when used for a non intended use For this reason read carefully all of the following advices e The transfer press may only be used for A printings on pressure and heat resistant materials Every exceeding use is seen as not intended If still used for non intended service the manufacturers will not be liable for the resulting damages Unauthorized reconstructions and modifications are not permitted because they will interfere with the security and the service of the machine e Don t insert any objects through the case notch Also make sure that no fluid will reach the transfer press and the heat element
10. lly and you will hear a beep 6 Exchange Heat Element and Work Plate 6 1 Build In and Extend a Heat Element Heizplatten Stecker Sen Deo Halte Schraube 15 ENGLISH Before you start to extend the heat element assure yourself that the heat element is cooled down to room temperature At first remove the heat element plug To do so you first of all have to loosen the corrugated head screw of the heat element plug with a phillips screwdriver Remove the heat element plug from the outlet Now you have to loosen both retaining screws of the heat element with a 13 way spanner and screw it out for approximately 3 4 mm Lift the heat element up and pull it towards you To build in a heat element do the same process in reversed order 6 2 Build In and Extend a Work Plate Halte Schrauben Loose both retaining screws on the underside of the work plate then just pull the plate out towards you ENGLISH SM 54 8 Problem Solving Transfer press does not work after 1 Compressed air pipe is not Connect the compressed air pipe with the 3 Pressure regulator is closed Turn the pressure regulator to the left Bin 4 Sliding table is not in end Push the sliding table until it blocks 5 Start buttons didn t get pushed at Push the start buttons both at the same 6 Pushed emergency stop Open the emergency stop After the printing process started Work plate was set up to low the Raise the work plat
Download Pdf Manuals
Related Search