User Manual
Contents
1. carefully so as not to damage the wires connectors or pins slowly insert the pin into the correct slot of the connector then snap closed the black tab that was lifted in step 1 Repeat these steps for each wire you need to change 21 Section 4 Cooling System NINETEEN HUNDRED User Manual 22 4 1 i Included Fans The NINETEEN HUNDRED comes with two standard top 120 mm TwoCool fans and a standard rear 120 mm TwoCool fan and three standard front 120 mm TwoCool These fans have two speed switches on the rear of the case that let you choose the speed best suited to your need The default fan speed setting is Low 120 mm TwoCool fan specifications Size 120 x 25 mm two speed fan Rated Voltage 12V DC Operating Voltage 12V 10 Input Current Static Pressure Noise Input Power High 0 204 1 208 m min 0 96 mm H O 23 65 2 4W 1200RPM 10 42 64CFM 0 037 inch H 0 dBA Low 0 10A 0 604 m3 min 0 24 mm H 0 17 00 1 2W 600RPM 10 21 32CFM 0 009 inch H 0 dBA 4 2 I Optional Fans The NINETEEN HUNDRED includes mounts for up to two more fans These mounts are as follows e 2x internal intake 120 mm mounts Internal intake 120 mm fans Just outside of the 3 5 drive bay area are two fan mounts for 120 mm internal intake fans 1 Align your fan with the pegs that correspond with the fan screw holes on the fan 2 Push your fan into the slot until secure You will hear your fan lock into place w2. circles show screw located Air filter 3x 120mm front intake FDB silent fan The NINETEEN HUNDRED features a removable PSU filter that can be unlocked for maintenance and locked for transport To remove the PSU filter push the ends of the filter down then pull the filter toward you using the tab outside of the chassis You can also lock the filter by pushing up on the tab once the filter is completely inside the chassis Remove the filter by pulling on the tab outside the chassis circled above 26 Antec Inc 47900 Fremont Blvd Fremont CA94538 tel 510 770 1200 fax 510 770 1288 Antec Europe B V Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel 49 40 226139 22 fax 31 0 10 437 1752 Technical Support US amp Canada 1 800 22ANTEC customersupport antec com Europe 31 0 10 462 2060 europe techsupport antec com www antec com Copyright 2013 Antec Inc All rights reserved All trademarks are the property of their respective owners Reproduction in whole or in part without written permission is prohibited Rev 2 3 10 7 2014 27
3. like to pass through the holes behind the motherboard tray Pull them through the hole toward the right side of the case Use the zip ties provided to hold your cables in place Zip ties can be anchored to tiedown locations located on the back of the motherboard panel For cables which will be routed back to front drives or other internal accessories feed the cables back through the insertion point nearest the destination of the cable Connect the cable and then pull the slack back to the right side of the case Use the grommet lined cable routing holes to route PSU cables The yellow circles show cable tiedown For cables which will be routed directly to front drives or other internal accessories cable tiedowns are located along the drive cage Bundle front drives or other internal accessories cables together and secure them using tiedowns 17 Section 3 Front 1 0 Ports NINETEEN HUNDRED User Manual 18 a USB 2 0 Connect the front I O panel USB cable to the USB header pin on your motherboard Check your motherboard user s manual to ensure that it matches the table below Pin Signal Names o Pin Signal Names USBPower1 USBPower2 NegativeSignal1 NegativeSignal2 O00 r O0O00O0 PositiveSignal1 MS PositiveSignal2 7 foot 5 oom 0 9 Key No Connection Empty Pin No HE 3 2 l USB 3 0 The NINETEEN HUNDRED comes with four front panel USB 3 0 ports and includes an internal motherboard c
4. 0 mm Rear exhaust fan 2 x 120 mm top exhaust fans Motherboard Mount SSI CEB E ATX ATX Micro ATX Mini ITX CPU cutout 10 Extra large cable routing space S 30mm 11 Power supply mount ATX ESP standard PSU x 2 12 Front Ports 4 x USB3 0 2x USB2 0 Audio In Out a En Oe a SS Nr 1 2 ll Chassis Specifications Chassis Type Super Full Tower Chassis Color Green Red Dimensions 27 4 H x 8 8 W x 21 8 D 696 mm H x 223 6 mm W x 555 mm D Weight Cooling Fan mounts 3 x 120 mm front intake fan mounts 2x 120 mm HDD internal fan mounts 1x 120 mm Rear exhaust fan mounts 2 x 120 140 mm top exhaust fan mounts Included Fan 3x 120mm front intake FDB silent fan 1200 r p m 18dB 1x 120mm rear exhaust FDB silent fan 1200 r p m 18dB 2 x 120mm top exhaust FDB silent fan 1200 r p m 18dB Drive Bays 3 x 5 25 tool less drive bays 12 x 3 5 2 5 tool less HDD bays 2 x 2 5 HDD bays Expansion Slots S Motherboard Size SSI CEB E ATX Standard ATX microATX Micro ATX Mini ITX Front I O Panel 4 x USB 3 0 with internal motherboard connector 2 x USB 2 0 Audio In Out Power and Reset buttons located on front panel of chassis 1 3 Included Screws An inventory of all screws and intended usage and quantity is provided here Front fan screw 4 HDD screw 50 CD ROM screw 6 Motherboard screw 13 Motherboard standoff 4 Power supply screw 4 2 5 tray mount sc
5. IMEC 25 NINETEEN User HUNDRED Manual Nineteen Hundred User Manual Congratulations on your purchase of the Antec Nineteen Hundred Meet the Nineteen Hundred a case engineered for performance and built to enclose the ultimate PC It is an unbeatable enclosure that delivers a combination of cooling performance and convenience and stands head and shoulders above the competition With 9 expansion slots the Nineteen Hundred features an advanced cooling system for graphics cards up to 330 mm 13 0 inches in length Dual layer mesh provides a stylish and new fashion into computer hardware Nineteen Hundred is using silicone grommets technology to limit vibrations In addition Its comes with 4 advance silent Fluid Dynamic bearing chassis fan which can provide lowest fan acoustic to under 18dB A Finally the Nineteen Hundred is constructed of durable SECC steel that lasts for builds to come Along with pioneering design and solid construction the Nineteen Hundred is the last word in ultimate PC builds At Antec we continually refine and improve our products to ensure the highest quality As such your new chassis may differ slightly from the description in this manual due to improvements applied for the optimal building experience As of October 01 2013 all features descriptions and illustrations in this manual are correct Disclaimer This manual is intended only as a guide for Antec s computer enclosures For more comprehe
6. compatible with the following CPU sockets Intel LGA 1155 1156 1366 2011 AMD AM2 AM3 AM2 AM3 FM1 Your unit may not contain the LGA 2011 mounting bracket To acquire this please contact Antec customer support information listed at end of manual Be sure to install the KUHLER H 0 with the end of the tubes positioned at the bottom of the radiator 1 Remove the rear fan by first disconnecting the power connector from the fan power hub directly above the fan 2 Remove the screws on the back of the chassis while supporting the fan with your other hand 11 Unscrew the rear fan to remove it 2 4 12 m Preparing the KUHLER H O backplate is specific to your CPU socket Please refer to the KUHLER H 0 installation guide available at http www antec com Believe_it product php id Mjc2OCYxNw KUHLER H O 620 or http www antec com Believe_it product php id NzAOMzcwJjE3 KUHLER H O 920 for more information Prepare the retention ring according to the CPU socket you re using Complete installation according to the KUHLER H O instructions l Power Supply Installation With the case upright place the power supply as illustrated in the image to the right Push the power supply to the back of the case and align the mounting holes Attach the power supply to the case with the screws provided Attach the power supply with the provided screws 2 5 External 5 25 Device Installation To in
7. e tray out 2 Place your 3 5 drive on the tray so that the holes line up with the silicone grommets 3 Using the 3 5 drive screws B in Section 1 3 secure your 3 5 drive to the tray We recommend using your hand to find the exact threading of the drive s holes then using a screwdriver to completely secure your drive Do not over tighten the screws as this will minimize the grommets ability to reduce vibration 4 Now that your drive is secured to the tray pinch the ends of the tray and insert your drive into the bay You will hear your device click into place Pinch the ends of the tray and insert your drive until it clicks 15 To install a 2 5 drive 1 Extract one of the drive trays by pinching the ends of the tray inward and pulling the drive tray out 2 Place your 2 5 drive on the tray so that the holes line up with the 2 5 tray holes 3 Using the 2 5 drive screws G in Section 1 3 secure your 2 5 drive to the tray with a screwdriver 4 Now that your drive is secured to the tray pinch the ends of the tray and insert your drive into the bay You will hear your device click into place 16 2 7 l Cable Management There is a cable management compartment between the motherboard and right side panel as well as cable tiedowns located on the back of the motherboard panel You can tuck excess cables in this compartment or route them to the drive bays Choose the cables you would
8. es are negative If the LED does not light up when the system is powered on try reversing the connection For more information on connecting LEDs to your motherboard see your motherboard user s manual Front panel leads Note Polarity positive and negative does not matter for switches 20 3 5 Rewiring Motherboard Header Connections There may come a time when you need to reconfigure the pin out of a motherboard header connector Examples could be for your USB header audio input header or some other front panel connector such as the Power Button connector Before performing any work please refer to your motherboard user s manual or your motherboard manufacturer s website to confirm the pin out needed for your connector We strongly recommend making a notated drawing before beginning work so that you can recover if your work gets disturbed Front panel headers Determine which wires you need to remove in order to rewire your plug to match the USB pin outs on your motherboard refer to your motherboard user s manual Working on one connector at a time use a very small flathead screwdriver or similar tool to lift up on the black tab located beside the gold posts squares This will allow you to easily slide out the pins from the USB plug Working carefully so as not to damage the wires connectors or pins slowly remove the pin from the connector Repeat these steps for each wire you need to change Working
9. hen the brackets around the fan snap into place Align your fan with the pegs that correspond with the fan screw holes on the fan 23 Secure an intake fan into place by aligning it with the pegs that correspond with the fan screw holes 4 3 l Fan Switch Controller The NINETEEN HUNDRED has two speed switches on the rear of the case that let you choose the speed best suited to your need Low mode 600 R P M High mode 1200 R P M 24 4 4 Air Filters There are three air filters in the NINETEEN HUNDRED Top front and PSU intake filter that can be removed and washed It is particularly noteworthy that the top and the front filters are combined with the fan How to remove the front fan filters Picture C Unscrew top and lower screw to remove fan filter Gently clean if water is used dry and replace top and lower screw Note From time to time it will be necessary to wash the installed air filter Not washing the air filter will result in higher system temperatures and possible stability problems We recommend checking the air filter at least once a month initially The frequency will change depending on system usage users whose systems run 24 7 will likely have to check wash more often than those who don t use their systems every day and on environmental conditions You can access the front filter by opening Before open the front panel please remove the screws on the p p p the front panel both sides the yellow
10. manual for your CPU cooler to find out if there are steps you must take before installing the motherboard e Do not sit on your chassis Although it is constructed of heavy duty steel and internally reinforced it is not designed to support the weight of an adult and may buckle e Remember to use the right tools for each task Do not use improvised screwdrivers like coins nails or knife blades as they may result in damage to screw threads or even injury Do not use your fingernails to separate edges or lift the sides of the chassis as paint chipping or injury may occur Section 2 Hardware Installation NINETEEN HUNDRED User Manual 2 1 Setting Up Put the case upright on a flat stable surface so that the rear panel power supply and expansion slots is facing you To remove the left and right side panels remove these thumbscrews first Note Place the panel thumbscrews aside carefully and remember where they are Remove the panel by gripping the end of the panel at the top amp bottom and swinging the panel outward Do not pull the panel back toward the rear of the chassis CAUTION Do not use your fingernails to pry or lift the panels Damage to the panels or injury to your fingernails may result Remove the panel by the end of the panel at the top amp bottom and swing the panel outward 2 2 i Motherboard Installation Before proceeding Check the manual for your CPU cooler to find out if there are steps yo
11. nsive instructions on installing the motherboard and peripherals please refer to the manuals that come with those components Table of Contents Section 1 Introduction 1 1 Getting to KNOW Your Chassis uses La I 5 1 2 Chassis Specifications Ai sense ihn 6 1 3 Ineluded Serews sn Erkalten 6 1 4 Belore You Beginn ebene 7 Section 2 Hardware Installation 2 1 SECUN UD MN RS N nine rene etes tes 9 2 2 Motherboard Installationen een 9 2 3 Installing KUHLER H 0 Liquid Coolers ss 11 2 4 POWEF SUDpIy Installatian ansehe eisen 12 2 5 External 5 25 Device Installation ss ein int ans an 13 2 6 Internal 3 5 2 5 Device Installation iii 15 2 7 Cable Management 17 Section 3 Front 1 0 Ports 3 1 DA A EE EE ee lose ee 19 3 2 BS A ETE E ERE E E EE cose E AE EE A EE AE AAE OEST EE AET E 19 3 3 AC 97 7D AUdIO POS 2 ee euer 20 3 4 Power Switch Reset Switch Hard Disk Drive LED Connectors 20 3 5 Rewiring Motherboard Header Connections 21 Section 4 Cooling System 4 1 Ia a ne E ec 23 4 2 ODO MAAS ee 23 4 3 Fan Switch CONTO uns nu nn RS des Once ue din eu sc 24 4 4 ATEOS ee RS ee nt en eue te 25 Section 1 Introduction NINETEEN HUNDRED User Manual 4 1 1 Getting to Know Your Chassis 3 x 5 25 external tool less drive bays 12 x 3 5 2 5 internal drive bays 2 x 2 5 internal drive bays 3 x 120 mm front intake fans 2 x 120 mm HDD internal fan mounts 1 x 12
12. onnector To access USB 3 0 capability from the front panel 1 Identify the USB 3 0 header on your motherboard 2 Connect the USB 3 0 header to the motherboard port Be sure to align the connector in the proper orientation so that you do not damage the pins on your motherboard ess Q 5 Align the connector properly to prevent damage to your motherboard 19 3 3 i AC 97 HD Audio Ports There is an Intel standard 10 pin AC 97 connector and an Intel 10 pin HDA High Definition Audio connector linked to the front panel of the chassis a e HDA AC 97 1 ma ca a 4 ac 4 nc CO 10 6 momp 6 tineoutR 8 Key nopin 8 Key nopin la moa 9 meow You can connect either the AC 97 or the HDA connector depending on your motherboard Locate the internal audio connectors from your motherboard or sound card and connect the corresponding audio cable Consult your motherboard or sound card manual for the pin out positions Even if your system supports both standards only use one connector 3 4 Power Switch Reset Switch Hard Disk Drive LED Connectors Connected to your front panel are LED leads for power and HDD activity as well as switch leads for the power and reset buttons Attach these to the corresponding connectors on your motherboard Consult your motherboard manual for specific pin header locations For LEDs colored wires are positive White or black wir
13. rew 16 Fan screw for HDD tray 4 1 a e Lo TOnmona gt 1 4 l Before You Begin In order to ensure that your building experience with the NINETEEN HUNDRED will be a positive one please take note of the following e While working inside your NINETEEN HUNDRED keep your chassis on a flat stable surface Make sure your build environment is clean well lit and free of dust e Antec chassis feature rounded edges that minimize the occurrence of hand injuries Nonetheless exercise caution and control when handling chassis interiors We strongly recommend taking the appropriate time and care when working inside the chassis Avoid hurried or careless motions e Handle components and cards with care Do not touch the unshielded components or contacts on a card Hold a card by its edges Hold a component such as a processor by its edges never by its pins e To avoid electrostatic discharge ground yourself periodically by touching an unpainted metal surface such as a connector or screw on the back of this computer or by using a wrist grounding strap e Before you connect a cable ensure that both connectors are correctly aligned and oriented Bent pins can be difficult to fix and may require replacement of the entire connector e This manual is not designed to cover CPU RAM or expansion card installation Please consult your motherboard manual for specific mounting instructions and troubleshooting Before proceeding check the
14. stall a 5 25 drive you will need to remove the side panel and open the front panel For side panel removal please see Section 2 1 13 For front panel removal please remove the screws on both sides first Picture A for locations With the side panel off carefully push the metal drive bay cover out of the drive bay Picture B Remove the adjacent plastic bay cover from the front panel Slide your 5 25 drive through the front of the chassis until it lines up flush with the front bezel You will feel the drive lock into position If you need more clearance on the inside of the chassis for your drive pull the drive bay tab on the inside of the chassis toward you and push the drive in further Picture C f you need to install additional 5 25 drive bays please remove the next metal cover and the adjacent plastic drive bay cover Before opening the front panel please remove the screws on the both sides the yellow circles show screw locations 14 To install a 5 25 drive please open the front panel if you need more clearance for your drive pull the drive bay tab on the side see Section 2 1 for more information about removing the side panel 2 6 li Internal 2 5 3 5 Device Installation The NINETEEN HUNDRED has 12 drive bays that are compatible with both 3 5 and 2 5 drives To install a 3 5 drive 1 Remove one of the drive trays by pinching the ends of the tray inward and pulling the driv
15. u must do before installing the motherboard Make sure you have the correct I O panel for your motherboard If the panel provided with the chassis isn t suitable please contact your motherboard manufacturer for the correct I O panel Make sure you have the correct I O panel The NINETEEN HUNDRED comes with 9 preinstalled motherboard standoffs These are positioned for Standard ATX motherboards but can be relocated to accommodate other form factors 1 Align the motherboard with the standoff holes on the motherboard tray and remember or mark which holes are lined up 2 Install standoffs as needed and put the motherboard in Install the motherboard standoffs by aligning the motherboard with the standoff holes CAUTION Make sure to remove any unused motherboard standoffs They may come into contact with the back of the motherboard and may electrify your chassis exterior if left connected 3 Screw your motherboard into the standoffs with the provided motherboard mounting screws 10 Use the provided motherboard mounting screws to secure your motherboard into the standoffs 2 3 Installing KUHLER H O Liquid Coolers The following instructs how to install the Antec KUHLER H 0 liquid CPU cooler 620 920 For any other CPU coolers please consult your manufacturer s installation guide Caution Check your motherboard s CPU socket to ensure its compatibility with the KUHLER H 0 The KUHLER H O 620 920 is
Download Pdf Manuals
Related Search