Cardbus/USB Wireless Adapter
Contents
1. D level LevelOne User Manual WUA 0315 11g Wireless USB Adapter Ver 1 0 0 1117 Safety FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interfe rence to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Example use only shielded interface cables when connecting to computer or peripheral devices2. lf any item is found missing or damaged please contact your local reseller for replacement 2 3 Setup The setup of the Wireless USB Adapter can be performed using the following steps Visually inspect the USB Adapter and make sure that it is fully plugged in to the USB port Make sure that there is a well environment that there is no much intrusion to have a better con nection 3 Hardware Installation 3 1 Installation Procedure for USB Adapter You should install the supplied software BEFORE inserting the Wireless USB Adapter when using Windows 2000 XP or Vista A Bi The following installation was operated under Windows XP and Vista Procedures are similar for Windows 2000 If you have installed the Wireless Adapter driver amp utility before please uninstall the old version first 3 2 LED Indicator The Wireless Adapter has a single Link Activity LED LED Status Description Link Act On Associated with the network Blue Off Not associated with the network Blinking Data being transferred 3 3 Check the Installation The LEDs of the Wireless USB Adapter are clearly visible and the status of the network link can be seen instantly e Once the device is plugged to the station s USB port the Link Act LED of the Wireless USB Adapter will light up indicating a normal status with power e While the Wireless USB Adapter linked up and transmitting data to the Access Point or to other Wireless LAN stat
3. 168 50 1 BW gt gt n a GI gt gt n a Link Screen Link Information Status Extra Info Channel Authentication Encryption Network Type IP Address Subnet Mask Default Gateway HT Link Quality Signal Strength 1 3 Noise Strength Link Speed Throughout MCS gt gt n a Cink Quatity gt gt 26 Signal Strength 1 gt gt 37 E Signal Strength 2 gt gt 44 Noise Strength gt gt 26 Transmit Link Speed gt gt 24 0 Mbps Throughput gt gt 0 000 Kbps Receive Link Speed gt gt 18 0 Mbps SNRO gt gt n a Throughput gt gt 4 784 Kbps SNR1 gt gt n a It will indicate the current link status It shows the link status It displays the current channel in use It will indicate the current authentication mode in use It shows the wireless security that the wireless network is using This will indicate Infrastructure or Ad hoc It shows the current IP address on the wireless interface Subnet mask for the current IP address Gateway IP address associated with the current IP address It displays current HT status in use 802 11n wireless card only It displays connection quality based on signal strength and TX RX packet error rate lt receives signal strength 1 3 user can choose to display as percentage or dBm format It displays noise signal strength It will show current transmit rate and receive rate It displays transmits and receive throughput in unit o
4. 86d0Bmi2dBm O 12Mbps 88dBmM 2dBm 9Mbps 824Bm 2dBm O Mbps 802 11b 88d4Bmi2dBm O 11Mbps 82d4Bm 2dBm O 5 5Mbps 92dBmi2dBm O 2Mbps 92dBmi2dBm O 1Mbps Transmitter Output Power Typical 802 11g 13 5 1dBm 802 11b 17 1 dBm 40 Network Security WEP 64 1 28 bit WPA WPA PSK WPA2 WPA2 PSK Support WPS configuration Device Management Windows Utility Software OS Supported Windows 2000 XP Vista 32bit Vista 64bit Physical Specifications LED Power Link Temperature Operating 0 C 40 C Storage 20 C 70 C Humidity 5 90 non condensing Power Requirement DC 5V 5 Dimensions 54 8 L x 21 4 W x 7 8 mm H Certifications CE FCC
5. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This transmitter must not be co located or operating in conjunction with any other antenna or transmitter CE Marking Warning Digital Data Communications declares that this product Model no WUA 0315 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC The CE Declaration of Conformity can be downloaded at http www levelone eu support php FECE O 11 Table of Content 1 INTKODUC FION uns oc iii oido lacio leia laicas 4 Wile User Manual OVA Wat A A A tE 4 2 UNPACKING A ND SETUP cicvcudesdacetuaselscsscacsdeteselescedsudesesensesnesssnesdetassdesedsategeseasssnestsueciecanstasesias 5 2k A AS 5 22 Packase COM oe E 5 Di AE on 5 3 HARDWARE INSTALLA TION a a as 7 3l Installation Procedure tor USB Adapleli ia 7 Je O O E 7 Sid Check the Taste asta 7 4 SOE TW AREA INSTALLATION bsssscacensscd escesesdccssseddcovsiegsceassaddeasesasdens
6. Successfully Frames Retransmitted Successfully Frames Fail To Receive ACK After Al Retries RTS Frames Successfully Receive CTS RTS Frames Fail To Receive CTS Reset Counter Status gt gt Disconnected Extra Info gt gt Channel gt gt Authentication gt gt Encryption gt gt Network Type gt gt IP Address gt gt Sub Mask gt gt Statistics Screen Transmit Frames Transmitted Successfully Frames Retransmitted successfully Frames Fail To Receive ACK After All Retries RTS Frames Successfully Receive CTS RTS Frames Fail To Receive CTS Receive Frames Receive Successfully 715 715 Link Quality gt gt 0 Signal Strength 1 gt gt 0 Noise Strength gt gt 0 Transmit Link Speed gt gt Throughput gt gt Frames successfully sent Frames successfully sent with one or more reties Frames failed to transmit after hitting retry limit Successfully receive CTS Clear To Send after sending RTS Request To Send frame Failed to receive CTS Request To Send after sending RTS Clear To Send Frames received successfully 32 Frames Receive With CRC Error Frames Dropped Due To Out of Resource Duplicate Frames Received Reset Counter 5 5 WMM Frames received with CRC error Frames dropped due to resource problem Frames received more than twice Click the button to reset counters to zero Click WMM tab of the utility and you will see the following
7. and an access point that is directly connected to the wired LAN Each wireless PC in this BSS can communicate with to any computer in its wireless group via a radio link or access other computers or network resources in the wired LAN infrastruc ture via an access point 38 LAN Extension da tiran Adapters Sahici a SN E S a p ar ne Ba 3 n ar J Notebeek with Wiraka USI Adapter po py f Access Park The infrastructure configuration not only extends the accessibility of wireless PCs to the wired LAN but also increases the effective wireless transmission range for wireless PCs by passing their signal through one or more access points A wireless infrastructure can be used for access to a central database or for connection be tween mobile workers as shown in the following figure 39 7 Technical Specifications Technical Specifications Standards IEEE 802 11g IEEE 802 11b Host Interface USB Port Type USB 2 0 1 1 1 0 Radio Operation Data Transfer Rate 802 11g 54 48 36 24 18 12 9 and 6 Mbps 802 11b 11 5 5 2 and 1 Mbps Modulation 802 119 OFDM 802 11b CCK QPSK BPSK Media Access Control CSMA CA with ACK Frequency Band 2 4GHz 2 4835GHz Number of Channels Channel 1 11 North America FCC Channel 1 13 Europe ETSI Receiver Sensitivity Typical 802 119 71dBmi2dBm O 54Mbps 74dBmi2dBm O 48Mbps 78dBm 2dBm O 36Mbps 81 dBmi2dBm O 24Mbps 84dBmi2dBm O 18Mbps
8. and verify the settings on this screen are correct 3 Click OK To delete a profile 1 2 Click Delete To edit a profile 1 2 On the Profile tab select the profile that you want to delete On the Profile tab select the profile that you want to edit Click Edit button Change the profile settings as necessary Click OK 23 To enable a profile 1 Inthe list of available profiles click the profile that you want to enable 2 Click Activate 5 2 Network The network setting page allows you to set and save different wireless settings You can activate the suitable profile according to the environment where the wireless connection is used This screen is displayed when you double click the system tray icon You can also click the Net work tab in the screen When you open the utility program it will scan all the channels to find all the access points stations within the accessible range and automatically connect to one of the wireless devices which have the highest signal strength EF LevelOne WUA 0315 a iz g e Sd O t Profile Network Advanced Statistics WMM WPS CCX Radio on off Sorted by gt gt O SSID Channel Signal Show dBm AP List gt gt 5400tab Dr g 9 13 MES WAP Wi g 1 MeetingRoom W 7 g Q 94 PM_AP bz BO ms PMWBR 6001 7 g Oe 100 EE QC 6000 Oo BODO x gt WAP 0003 Ds g 9 73 EE Rescan Add to Profile Connect a Status gt gt WAP 0003 lt gt 00 11 6B 6
9. gt Encryption gt gt Network Type gt gt IP Address gt gt Sub Mask gt gt WPS Screen WPS WPS AP List Rescan Information Signal Strength 1 gt gt 0 Noise Strength gt gt 0 Transmit Link Speed gt gt Throughput gt gt lt displays the information of surrounding APs with WPS IE from last scan result List information includes SSID BSSID Channel ID Device Password ID and Securi ty Enabled Click this button to update information on surrounding wireless network Display the information about WPS on the selected network List information includes Authentication Type Encryption Type Config Methods Device Password ID Selected Registrar State Version AP Setup Locked UUID E and RF Bands 35 PIN Code Config Mode Detail Connect Rotate Disconnect Export Profile Delete PIN PBC WPS associate IE WPS Probe IE Progress Bar Status Bar Enter the PIN code displayed in the following field to the WPS screen of the access point When STA is Enrollee you can use Renew button to re generate new PIN Code Our station role playing as an Enrollee or an external Registrar Information about Security and Key in the credential Click this button to connect to the selected network inside credentials Click this button to rotate to connect to the next network inside credentials Click this to stop WPS action and disconnect this active link And then
10. is installing LevelOne 11g Wireless LAN InstallShield 11 LevelOne 11g Wireless LAN InstallShield Wizard InstallShield Wizard Complete The InstallShield Wizard has successfully installed LevelOne 11g Wireless LAN Click Finish to exit the wizard 8 Insert the USB adapter into USB port when installation procedures are completed 9 The Windows Found New Hardware wizard will prompt and then install the software auto i Found New Hardware x 802 11 USB Wireless LAN Card 10 When the Windows wizard is complete you will now have a new icon in your system tray matically The installation program will help you to setup the Wireless LAN utility Be noted that the Windows XP has its own Wireless Utility you can either use the utility of Windows XP or the provided utility When the Wireless LAN utility is installed properly you will see the icon on the Windows task bar The user can configure the wireless settings using the Wireless USB Adapter Configuration Utility Double click the utility icon that appears in the taskbar When the icon in the toolbar represents in full blue color then the signal strength has an excellent performance with the AP if it represents in half blue color then the signal strength has a fair perfor 12 mance with the AP and if the icon represents in low blue then the signal strength has a worst formance with the wireless station E E BOO Excellent Wireless Signal Stren
11. select the last profile at the Profile Page of utility if exist If there is an empty profile page the driver will select any non security AP Export all credentials to Profile Click to Delete an existing credential And then select the next credential if exist If there is an empty creden tial the driver will select any non security AP Start to add to Registrar using PIN configuration me thod If STA Registrar remember that enter PIN Code read from your Enrollee before starting PIN Start to add to AP using PBC configuration method send the association request with WPS IE during WPS setup It is optional for STA Send the probe request with WPS IE during WPS se tup It is optional for STA Display rate of progress from Start to Connected status Display currently WPS Status 36 5 7 Radio On Off You can turn the radio signal on off by clicking this button ES Te m sas BB O amp Advanced Statistics WMM WPS CCX Radio on off The radio signal is on Radio onfott H The radio signal is off Radio on off 5 8 About This page displays the information of version numbers configuration utility firmware and other information regarding this wireless USB adapter Click the www level1 com button to visit the Leve One website for other information il LevelOne WUA 0315 rx zan PLA 4 o m Network Advanced Statistics WMM WPS CCX Radio on off About c Copyright 2008 Lev
12. 0 64 C5 A Extra info gt gt Link is Up TxPower 100 Sana SHERBET gt gt 70 Channel gt gt 6 lt gt 2437 MHz Noise Strength gt gt 26 Authentication gt gt Open Encryption gt WEP Network Type gt gt Infrastructure Transmit IP Address gt gt 169 254 12 208 Link Speed gt gt 54 0 Mbps Sub Mask gt gt 255 255 0 0 Throughput gt gt 27 792 Kbps Default Gateway gt gt 0 0 0 0 Network Screen The SSID up to 32 printable ASCII characters is a unique name identified in a WLAN SSID 24 Network Type Channel Wireless Mode Security Enable Signal Rescan Add to File Connect lt displays the Network type in use Infrastructure for BSS Ad Hoc for IBSS network The channel used by the Wireless network AP support wireless mode It may support 802 11a 802 11b or 802 119 wireless mode Whether AP provides security enabled wireless network This is displayed as percentage 0 100 of specified network Click this button to rescan for all Wireless net works Click this button to add the selected AP to Profile setting It will bring up profile page and save user s setting to a new profile Click this button to connect the Wireless network Wireless Network Sequence order You can click the radio buttons in the Sort by gt gt section ex SSID Channel or Signal to arrange the Wireless network in the desired order To Connect to a Wireless Network C
13. Codes to choose from 30 Enable CCX Cisco Compatible eXtensions Apply CCX Cisco Compatible Extensions is developed by Cisco for the radio monitoring and fast roaming Turn on CCKM During normal operation LEAP enabled client devices mutually authenticate with a new access point by performing a complete LEAP authentication including communication with the main RADIUS server When you configure your wireless LAN for fast re association however LEAP enabled client devices roam from one access point to another without involving the main server Using Cisco Centralized Key Management CCKM an access point configured to provide Wireless Domain Services WDS takes the place of the RADIUS server and authenticates the client so quickly that there is no perceptible delay in voice or other time sensitive appli cations Enable Radio Measurement When this parameter is enabled the Cisco AP can run the radio monitoring through the associated CCX compliant clients to conti nuously monitor the WLAN radio environment and discover any new Aps that are transmitting beacons Click this button to save the changes you made 31 5 4 Statistics Click Statistics tab of the utility the page will display the transmitted and received results in h LevelOne WUA 0315 lhe Ii E delo sie S Exe a 0 2 Profile Network Advanced Statistics WMM WPS CCX Radio on off et ae c Transmit Receive Frames Transmitted
14. copyright laws and international copyright treaties as well as other intellectual property laws and treaties The SOFTWARE PRODUCT ts licensed not sold 1 PLATO MAFIA IP CFI O do not accept the terms of the license agreement Select Install driver and LevelOne 11g WLAN Utility or Install driver only then click Next to continue the installation LeyelOne 118 Wireless LAN InstallShield Wizard Setup Type Select the setup type that best suits your reeds Choose to install Install driver only ae New 5 Select LevelOne 11g Configuration Tool then click Next to continue the installation LeyelOne 118 Wireless LAN InstallShield Wizard Setup Type Select the setup type that best suits your reeds Select Configuration Tool O Microsoft Zero Configuration Tool C e 6 Click Install to continue the installation 10 LeyelOne 118 Wireless LAN InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation IF pou want to review or change any of pour installation settings click Back Click Cancel to exit the wizard InstallShield Install Cancel 7 Follow the on screen instruction and step through the installation procedures then click Finish to exit the wizard LevelOne 11g Wireless LAN InstallShield Wizard Setup Status The InstallShield Wizard
15. d then install the software au tomatically Fi Driver Software installation E 802 11 USB Wireless LAN Card installed The software for this device has been successfully installed 802 11 USB Wireless LAN Card Ready to use Close 9 When the Windows wizard is complete you will now have a new icon in your system tray The installation program will help you to setup the Wireless LAN utility Be noted that the Windows Vista has its own Wireless Utility you can either use the utility of Windows Vista or the pro vided utility When the Wireless LAN utility is installed properly you will see the icon on the Windows task bar The user can configure the wireless settings using the Wireless USB Adapter Configuration Utility Double click the utility icon that appears in the taskbar 16 When the icon in the toolbar represents in full blue color then the signal strength has an excellent performance with the AP if it represents in half blue color then the signal strength has a fair perfor mance with the AP and if the icon represents in low blue then the signal strength has a worst performance with the wireless station a Excellent Wireless Signal Strength Adequate Wireless Signal Strength Low Wireless Signal Strength a Wireless Card inactive 17 5 Wireless Utility Configuration For Windows XP and Vista 5 1 Profile The Profile List keeps a record of your favorite wireless settings at home office and other
16. e 802 1x standard Data transmissions are encrypted using the WPA stan dard WPA PSK PSK means Pre shared Key You must enter this Passphrase value it is used for both authentication and encryp tion WPA2 This version of WPA2 requires a Radius Server on your LAN to provide the client authentication according to the 802 1x standard Data transmissions are encrypted using the WPA2 standard WPA2 PSK This is a further development of WPA PSK and offers even greater security You must enter this Passphrase value it is used for both authentication and encryption WPA None If selected you can only set encryption and WPA Preshared Key settings 20 Encryption Use 802 1x WPA Preshared Key WEP Key 1 4 The available options depend on the Authentication method se lected above The possible options are None No data encryption is used WEP If selected you must enter the WEP data shown below This WEP data must match the Access Point or other Wireless stations AES TKIP These options are available with WPA PSK WPA2 PSK WPA and WPA2 Select the correct option This setting only takes effect when using Open Shared WPA or WPA2 mode If enabled click the 802 1x tab to configure the related settings For WPA PSK and WPA2 PSK modes you need to enter the desired value 8 63 characters Data is encrypted using a 256Bit key derived from this key Other Wireless Stations must use the sam
17. e key This setting is only available for Open or Shared mode There are 2 modes Hex Only A F a f and 0 9 are allowed to be entered ASCII Numerical values characters or signs are all allowed to be entered 21 802 1x EAP Method There are 5 methods in the drop down list PEAP Protect Extensible Authentication Protocol PEAP trans port securely authentication data by using tunneling between PEAP clients and an authentication server PEAP can authenti cate wireless LAN clients using only server side certificates thus simplifying the implementation and administration of a secure wireless LAN TLS Smart Card Transport Layer Security Provides for certifi cate based and mutual authentication of the client and the network lt relies on client side and server side certificates to perform authentication and can be used to dynamically generate user based and session based WEP keys to secure subsequent communications between the WLAN client and the access point TTLS Tunneled Transport Layer Security This security method provides for certificate based mutual authentication of the client and network through an encrypted channel Unlike EAP TLS EAP TTLS requires only server side certificates EAP FAST Flexible Authentication via Secure Tunneling lt was developed by Cisco Instead of using a certificate mutual authen tication is achieved by means of a PAC Protected Access Credential which can be ma
18. ed by copyright laws and international copyright treaties as well as other intellectual property laws and treaties The SOFTWARE PRODUCT is licensed not sold E d e T Y D 1 Am d rd il ARA a 111 Ls accept the terms of the license agreement 1 do not accept the terms of the license agreement InstallShield 4 Select Install driver and LevelOne 11g WLAN Utility or Install driver only then click Next to continue the installation 14 Setup Type Select the setup type that best suits your needs Choose to install 9 Install driver and LevelOne 11g WLAN Utility Install driver only InstallShield 5 Click Install to continue the installation Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation If you want to review or change any of your installation settings click Back Click Cancel to exit the wizard InstallShield u _ e o ooo a I ooo mMM 15 6 Follow the on screen instruction and step through the installation procedures LevelOne 11g Wireless LAN InstallShield Wizard Setup Status The InstallShield Wizard is installing LevelOne 11g Wireless LAN Installing CA WU4 0315 119 Wireless USB adapter CCXSEAP PEAP msi Cancel 7 Insert the USB adapter into USB port when installation procedures are completed 8 The Windows Driver Software Installation wizard will prompt an
19. elOne Inc All rights reserved Utility Version gt gt 2 2 3 0 Date gt gt 11 06 2008 Driver Version gt gt 2 2 4 0 Date gt gt 10 29 2008 EEPROM Version gt gt 1 0 Firmware Version gt gt 0 12 Phy_Address gt gt 00 C0 02 2D 7A B2 www levell com 37 6 Network Planning LevelOne WUA 0315 11g Wireless USB Adapter supports a stand alone wireless network configuration as well as an integrated configuration with Ethernet LANs The wireless USB adapter can be configured as Ad hoc for small peer to peer networks with other wireless devices Infrastructure for a wireless extension to an existing wired LAN through an access point Network Topologies Ad Hoc Wireless LAN An ad hoc wireless LAN consists of a group of computers each equipped with a wireless adap ter connected via radio signals as an independent wireless LAN Computers in a specific ad hoc wireless LAN must be configured to the same radio channel An ad hoc wireless LAN can be used for a small branch office or SOHO operation Ad hos Wireless LAN Netebook with iy EN Viral ass USB Ade phar 9 l IAC Notabeek with l b Wirka USE Adapter PC with Wireless Win ass US Adaptar Infrastructure Wireless LAN LevelOne WUA 0315 can also provide access to a wired LAN for wireless workstations An inte grated wired and wireless LAN is called an Infrastructure configuration A Basic Service Set BSS consists of a group of wireless PC users
20. esources Click the check box and then click Apply button to apply this function to the system Click the check box and select the desired type of power saving mode Enable the check box and you may start to set MAC Address Timeout Value and check the DLS Status Click Apply and this setting will be applied to the system Enter the remote system which you want to connect with When you want to enable this function you have to make sure that your wireless network supports WMM function and then enter the MAC address of the adapter which wants to connect with the remote system The utility performs time outs so that the program does not sit idle waiting for input that may never come Set a value to apply to the system with WMM Click this button to save the changes you made Click this button will disconnect the selected Direct Link Setup 34 You will use the WPS screen when you try to connect the wireless network with the WPS function IHT LevelOne WUA 0315 S Fa ae S db s e Profile Network Advanced Statistics WMM WPS CCX Radio on off WPS AP List Rescan ID PMWBR 6001 00 11 6B 2A 30 C6 7 Ale EIP ID QC 6000 00 11 6B 17 48 F6 11 v Pin Code pp 22341 310 Renew WPS Profile List Config Mode lEnrolee Y 4 pi p PIN di WPS Associate IE Progress gt gt 0 PBC di WPS Probe IE Disconnect a Status gt gt Disconnected Link Quality gt gt 0 Extra Info gt gt Channel gt gt Authentication gt
21. f Mbps 21 5 3 Advanced Click Advanced tab of the utility you can configure the detailed settings in this page Windows Vista Screen ome Hetwak Abend Sa WM WPS CCX Radio on off Wireless mode gt gt 2 4G y Wireless Protection Auto w Enable TX Burst _ Enable TCP Window Size C Fast Roaming at 70 dBm Select Your Country Region Code 11B G gt gt fo CH1 11 CAUCA e A 15 ta Profile Network Advanced Statistics WMM WPS CCX Radio on off _ Enable CCX Cisco Compatible eXtensions CAC gt gt ADDTS Directiy send TS 7 Set n id Enabie Radio Measurements 5 z Diagnosis gt gt Select Profile Diagnose C Non Serving Channel Measurements limit z i 250 ms 0 2000 Information of selected profile O NetworkEAP Profile Name gt gt C Enable RF Roaming SSID gt gt Mo Y naenosis Capable gt gt C Enable CACiTolerance Diagnosis Capable 28 Windows XP Screen LevelOne WUA 0315 LL S Profile Network Advanced Statistics AAAA WPS Radio on off Mek me Enable CCX Cisco Compatible extensions Wireless Protection gt Auto Tx Rate gt gt Auto r dl Enable Tx Burst Enable TCP Window Size _ Fast Roaming at dEm Show Authentication status Dialog Select Your Country Region Code T1IBsG gt gt lo 2HA1 11 Status gt Disconnected Link Quality gt 0 Signal Strength 1 gt gt 0 Moise Streng
22. gth Adequate Wireless Signal Strength Low Wireless Signal Strength Wireless Card inactive 4 2 Windows Vista Utility Installation Insert the 11g Wireless USB Adapter Utility CD into the computer and then the Auto run screen will appear Alternatively open a file browser and double click on the autorun exe file located in the CD directory Click Utility to install the driver and utility and the install wizard will begin installing the soft ware Follow the install wizard instructions to complete the installation ver gE in ne WUA 0315 11g Wireless USB Adapter 13 3 Follow the Install Shield Wizard Instructions Select I accept the terms of the license agreement then click Next to start the installation T esrelfime Tle Wiirelecc ANI Inctal Sh roa LevelOne 11g Wireless LAN InstallShield gt Nos Preparing Setup Please wait while the InstallShield Wizard prepares the setup y LevelOne 11g Wireless LAN Setup is preparing the InstallShield Wizard which will guide you through the rest of the setup process Please wait InstallShield License Agreement Please read the following license agreement carefully LevelOne Wireless Utility for Windows 2000 P Vista Copyright C Digital Data Communication Co Ltd All Rights Reserved Thank you for purchasing LevelOne Wireless product SOFTWARE PRODUCT LICENSE The SOFTWARE PRODUCT is protect
23. ion the Link Act LED will start alternate blinking 4 Software Installation This section will lead you to install the driver and utility of the 11g Wireless USB Adapter 4 1 Windows XP Utility Installation 1 Insert the 11g Wireless USB Adapter Utility CD into the computer and then the Auto run screen will appear Alternatively open a file browser and double click on the autorun exe file located in the CD directory 2 Click Utility to install the driver and utility and the install wizard will begin installing the soft ware Follow the install wizard instructions to complete the installation WUA 0315 11g Wireless USB Adapter 3 Follow the Install Shield Wizard Instructions Select l accept the terms of the license agreement then click Next to start the installation LevelOne 112 Wireless LAN InstallShield Wizard Preparing Setup Please wat while the InstallShield Wizard prepares the setup Level0ne 119 Wireless LAN Setup ts preparing the InstallShield Wizard which will guide you through the rest of the setup process Please watt LeyelOne 112 Wireless LAN Installshield Wizard License Agreement Please read the following license agreement carefully Levelline Wireless Utility for Windows 200044P Yista Copyright E Digital Data Communication Co Ltd All Rights Reserved Thank vou for purchasing LevelOne Wireless product SOFTWARE PAODUCT LICENSE The SOFTWARE PRODUCT ts protected by
24. lick the name of the wireless network to which you want to connect and then click Connect Note that once you are connected to a Wireless network the Network screen will identify the current wireless network with a blue arrow icon as shown below 23 3 LevelOne WUA 0315 D o n dsb Ld Profile Network Advanced Statistics Sorted by gt gt O SSID Channel Signal AP List gt gt 5400tab Dr BS 9 13 WAP pH b g 31 MeetingRoom W 7 g Q 94 PM_AP 3 B g n 9 23 PMWBR 6001 7 g inky 100 QC 6000 Dr BS inky 31 wap 0003 De a 735 Rescan Add to Profile Connect Icons te 802 11b wireless mode ta 802 11g wireless mode 802 11n wireless mode It indicates network type is Ad hoc mode WMM WPS CCX Radio on off O Show dBm It indicates network type is infrastructure mode It indicates security enabled wireless network 4 It shows the information of Link Status Section a t hides the information of Link Status Section Link Status The Link Status section displays the detailed information of the current connection Click button to show the status screen 26 Status gt gt WAP 0003 lt gt 00 11 6B 60 6A C5 Extra Info gt gt Link is Up TxPower 100 Channel gt gt 6 lt gt 2437 MHz Authentication gt gt Open Encryption gt gt WEP Network Type gt Infrastructure IP Address gt gt 192 168 50 155 Sub Mask gt gt 255 255 255 0 Default Gateway gt gt 192
25. naged dynamically by the authentica tion server The PAC can be provisioned distributed one time to the client either manually or automatically Manual provisioning is delivery to the client via disk or a secured network distribution method Automatic provisioning is an in band over the air distri bution MD5 Challenge Message Digest Challenge Challenge is an EAP authentication type that provides base level EAP support It provides for only one way authentication there is no mutual authentication of wireless client and the network 22 Tunnel Authentica tion Session Resump tion Authentication ID Password Tunnel ID Pass word Use Client certifi cate Use certificate chain To add a profile 1 Select the desired option from the drop down list After reconnecting the signal which broke up you can enable the session resumption to reduce the transferring packet to accelerate the speed Enter the required data into the fields Enter the ID and Password for the tunnel Click the checkbox to enable certificate authority server function When the EAP authentication type such as TLS TTLS or PEAP is selected and required a certification to tell the client what server credentials to accept from the authentication server in order to verify the server you have to enable this function and enter the required data in the related fields On the Profile tab click Add button 2 Complete
26. public hot spots You can save multiple profiles and activate the correct one at your preference The following Figure shows the basic profile section Click Add to Profile button on the Network tab or you can choose Profile tab of the utility then click Add the Add Profile window will pop up Users can setup the general settings encryption and authentication settings and so on lf you want to do the general settings please follow the instruc tions below iy LevelOne WUA 0315 a P TA FA E a E delo amp A A o Profile Network Advanced Statistics WMM WPS CCX Radio on off Profile List Profile Name gt gt SSID gt gt Network Type gt gt Authentication gt gt Encryption gt gt Use 802 1x gt gt Tx Power gt gt Channel gt gt Power Save Mode gt gt RTS Threshold gt gt Add Import Fragment Threshold gt gt a Status gt gt Disconnected Link Quality gt gt 0 Extra Info gt gt Signal Strength 1 gt gt 0 Channel gt gt Noise Strength gt gt 0 Authentication gt gt Encryption gt gt Network Type gt gt Transmit IP Address gt gt Link Speed gt gt Sub Mask gt gt Throughput gt gt Profile Screen System Config Profile Name Enter or select a suitable name for this profile Each profile must have a unique name 18 SSID Power Save Mode RTS Threshold Fragment Threshold Network Type Tx Power Preamble OK button Cancel button lf the desi
27. red wireless network is currently available you can select its SSID Otherwise type in the SSID of the desired wire less network Select either CAM Constantly Awake Mode or PSM Power Saving Mode Select a value within the range of 0 to 2347 bytes Select the value from 256 to 2346 bytes The default value is 2346 select the desired option Infrastructure Select this to connect to an Access point Ad Hoc Select this if you are connecting directly to another computer Select the Tx transmission power according to the real environ ment The preamble defines the length of the CRC cyclic redundancy check Select either Auto or Long Preamble Click this button to save the settings and close the page The Cancel button will discard any data you have entered and exit the page 19 Auth Encyp Authentication You MUST select the option to match the Wireless LAN you wish to join The available options are Open Broadcast signals are not encrypted This method can be used only with no encryption or with WEP Shared Broadcast signals are encrypted using WEP This me thod can only be used with WEP LEAP Light Extensible Authentication Protocol is a pre EAP Cisco proprietary protocol If selected you have to enter the iden tity password and domain name of your computer WPA This version of WPA requires a Radius Server on your LAN to provide the client authentication according to th
28. screen IRH LevelOne WUA 0315 E ii u Profile Network Advanced WMM Setup Status WMM gt gt Enabled Power Save gt gt Disabled al WMM Enable C WMM Power Save Enable O Direct Link Setup Enabte pE TE e Status gt gt Disconnected Extra Info gt gt Channel gt gt Authentication gt gt Encryption gt gt Network Type gt gt IP Address gt gt Sub Mask gt gt Ea aa p Statistics WMM WPS cc Radio on off Direct Link gt gt Disabled a Link Quality gt gt 0 Signal Strength 1 gt gt 0 Noise Strength gt gt 0 Transmit Link Speed gt gt Throughput gt gt 33 WMM Screen WMM Enable WMM Power Save Enable Direct Link Setup Enable MAC Address Timeout Value Apply Tear Down 5 6 WPS WPS Wi Fi Protected Setup can simplify the process of connecting any device to the wireless network by using the push button configuration PBC on the Wireless Access Point or entering a PIN code WMM is short for Wi Fi Multimedia It is a standard created to define quality of service QoS in Wi Fi networks It is a precursor to the upcoming IEEE802 11e WLAN QoS draft standard which is meant to improve audio video and voice applications transmit ted over Wi Fi WMM adds prioritized capabilities to Wi Fi networks and optimizes their performance when multiple concur ring applications each with different latency and throughput requirements compete for network r
29. ssalsasusdegacaassagdessesasdeesiead cace 8 AL Windows Utility Tns llana RA ii 8 AD Nvimdows Vista Utility Tasa 13 5 WIRELESS UTILITY CONFIGURATION FOR WINDOWS XP AND VISTA 18 Tae 460 Gl Se eee Te RTO ee eR Te Mee enT mt ree arena nec rn E meter 18 Ie NOWO at ieee a heres E han ea ca 24 PP O 32 Ia WMM ienne oie 33 IOs P ea A T a 34 Da Rado IM a 37 KOs ADO ados 37 6 NETWORK PLANNING curieri A a es 38 7 TECHNICAL SPECIFICA TIONS sistissscsdececasantzescsedeecdecastacsecedeceassentnasaeeddedeacastecteccdeceastentaaseeetes 40 111 1 Introduction Congratulations on your purchase of LevelOne 11g Wireless USB Adapter This manual helps to get familiar with the LevelOne 11g Wireless LAN Adapter This manual con tains detailed instructions in operation of this product Please keep this manual for future reference With a Wireless LAN Adapter a laptop computer or a station can communicate with another com puter in a wireless way Easy to use utilities are bundled with Wireless LAN Adapter for configuration monitoring and diagnosis purposes Wireless LAN Adapter can wirelessly transmit and receive data with the Wireless LAN Adapter you can locate your Notebook PC or station wherever you want without wires and cables Wireless LAN Adapter provides users with an access to real time information anywhere in their organization The mobility provides productivity and service which are not available under wired ne
30. th gt 0 Extra Info gt gt Channel Authentication gt Encryption gt gt Network Type gt gt Transmit Mer IP Address gt Link Speed gt gt boas Sub Mask Throughput Default Gateway gt gt Receive Link Speed Throughput Advanced Screen Advanced Wireless Mode select the desired wireless mode Enable Tx Burst Tx Burst enables the adapter to deliver better throughput during a period of time but the function only takes effect when connecting with the AP which also supports Tx Burst 29 Enable TCP Window Size Fast Roaming at Show Authentication Status Dialog Select Your Country Region Code The TCP Window is the amount of data which a sender can send on a particular connection before it gets an acknowledgement back from the receiver that it has got ten some of it When the router or AP which the adapter is connecting to has set up the TCP Window you can enable the parameter to meet the data size for the router or AP connection The larger TCP Window the better performance When you want to fast roaming to the network nearby without intercepting the wireless connection especially the adapter is applied to the multimedia application or a voice call you can enable this function When connecting to an AP with authentication if enabling this function it will display dialogs about 802 1x authenti cation during the process There are 8 kinds of Country Region
31. tworks The Wireless LAN Adapter configuration is easy to change from peer to peer networks suitable for a small number of users to full infrastructure networks of thousands of users that al low roaming around a broad area 1 1 User Manual Overview Introduction Describes 11g Wireless USB Adapter Unpacking and Setup Helps user to get started with the basic installation of the 11g Wireless USB Adapter Hardware Installation Describes the LED indicators of the 11g Wireless USB Adapter Software Installation Tells how to setup the driver and the utility setting Technical Specifications Lists the technical general physical and environ mental specifications of the 11g Wireless USB Adapter 2 Unpacking and Setup This chapter provides the package contents and setup information for the 11g Wireless USB Adapter 2 1 Features e Compatible with IEEE 802 11b and IEEE 802 11g standards e Enjoy high speed Wireless connectivity through your USB port e Easy Plug and Play setup with installation wizard e Supports 64 128 bit WEP WPA and WPA2 encryption for high level security e Portable and mini size design e Windows configuration for Wi Fi Protected Setup WPS e Supports Window 2000 XP Vista 2 2 Package Contents Open the box of the 11g Wireless USB Adapter and carefully unpack it The box should contain the following items e WUA 0315 11g Wireless USB Adapter e Quick Installation Guide e CD Manual Driver Utility
Download Pdf Manuals
Related Search