user manual
Contents
1. VLPR 54L922D Professional Car License Plate Camera User Manual Veilux Inc safety Information CAUTION 1 Never point the camera toward the sun Do not expose the lens directly to the sun or to strong light as this may damage the pick up device 2 Handle this camera with care Avoid any shock of the camera Improper handing could damage the camera 3 Requires a proper operating environment This camera is designed for both indoor and outdoor use The allowable temperature range of operation of this camera is between 10 C 50 C and the allowable humidity is 80 maximum 4 Clean the lens regularly It is recommended that the lens surface be cleaned regularly or when the lens is dusty to prevent obstruction of IR light Cleaning should be done by using a chamois a very fine soft cloth lens tissue or cotton tipped applicator and ethanol to carefully remove any fingerprint of dust 5 Check the power source voltage The power source voltage should be within the specified range Camera must meet the specification 2 safety information content CONTENT INTRODUCTION Features Dimension INSTALLATION Nomenclature and Function Installation Important Notes TECHNICAL INFORMATION Specification 3 content CO O Ol introduction FEATURES 1 Lead Pb Free RoHS Compliance Digital Signal Processor Sony HQ1 IN Long life and high reliability are achieved by the use of a CCD image device This makes the came2. waterproof lid 4 HIR LEDs Adjustment Ther external IR LEDs adjustment is used to adjust the brightness of the 6 pieces high power reflection IR light As the installation environment changes or according to different illumination conditions users can adjust a proper IR brightness 5 installation installation INSTALLATION 1 Please adhere the paster provided to the surface where you like to install the bracket on the wall as Fig1 In accordance with the position of 4 holes shows on the paster to dig 4 holes and then insert 4 anchors provided into the holes as shown in Fig2 Fig1 E Fig2 P AW gt a Sa r Ne e 2 Mounting the camera to the wall by 4 screws You can let the camera cables go along the sides as Fig3 or go downward as Fig4 If the cable goes downward a plastic cable protector provided is needed shown in Fig4 3 In accordance with the direction shown in Fig5 to adjust the direction of the camera bracket as you like Fig5 6 installation installation INSTALLATION 4 Please note During camera adjustment there are 2 screws as shown in Fig6 which you don t need to unfasten them Fig6 VAN i Bb A Do not unfasten these 2 screws 5 Use an L type wrench provided to fasten the screw to the buttom of the camera as Fig Please hold the camera until the installation is finished Fig7 6 Then use the wrench to fasten the screw to the connector of the cam
3. era and bracket as shown in Fig8 Please hold the camera until the installation is finished 7 installation installation INSTALLATION 7 Use the wrench to fasten the screw to the bracket as shown in Fig9 Please hold the camera until the installation is finished Fig9 IMPORTANT NOTES 1 To simulate the motion of cars in the parking lot it takes 3 5 minutes to switch from B W mode to Color mode 2 The maximum elevation angle of LPR function is 20 degrees Refer to Fig11 Fig11 pet pou reading distance mounting height elevation angie 8 installation technical information SPECIFICATION ITEM VLPR 54L922D TV System NTSC PAL Image Sensor 1 3 Sony Super HAD CCD Il 795 H x 596 V Minimum Illumination O Lux Signal to Noise Ratio Light Filter Color mode Switching Time 3 5min Auto Gain Control Automatic Automatic Auto White Balance Automatic Digital Noise Reduction Automatic Dynamic Digital Noise Reduction DNR oense Up Automatic Automatic IRIS DC Adjustment VR Lens Angle of View H License Plate Distance Power Supply 12V DC 24V AC Operation Storage Temp 10 C 50 C 20 C 60 C Operat Stor Humidity Maximum RH80 RH9096 Dimension 93 0 x 163 L mm Net Weight 1 000g 2 2Ibs 9 technical informataion 3015 Eagle Drive Suite 100 Grand Prairie Texas 5052 Toll Free 800 510 6528 Local 214 635 4855 Fax 214 988 2858 www ve
4. ilux net
5. ra 10096 solid state P Easy of use in any application is achieved through the small size Lower power consumption Relatively no interference from magnetic or electrostatic field LOS Patent designed external varifocal lens adjustment for users to adjust the focus conventiently without removing the cover 8 The cable management bracket protects the camera cables inside the bracket to keep it away from humidity in outdoor environment 9 Mechanical Visible Light Filter This Mechanical Visible Light Filter will be triggered by strong focused illumination Whenver strong light appears it will filter out the strong light automatically so that clear and readable quaility images can be ensured 10 The FL ON Shutter is fixed at 1 230 second 11 From Night to Day the delay time is 5 6 minutes DIMENSION 4 introduction Installation NOMENCLATURE AND FUNCTION 1 External Varifocal Lens Adjustment Wide Tele Please use a flat head screw driver to adjust the lens angle for wide and telephoto 2 External Varifocal Lens Adjustment Near Far Please use a flat head screw driver to adjust the lens focus for near and far External Varifocal Lens Adjustment eee c ml 12Vdc 24Vac DC Level and HIR LEDs Adjustment 3 DC Level The VR for adjusting the IRIS level of DC Auto Iris Lens Please lift the waterproof lid and use a small screw driver to adjust the DC leve After the setting is done please cover back the
Download Pdf Manuals
Related Search