Marmitek SMM31 user manual
Contents
1. is possible that the Haibrain X 10 signals are disturbed by e g baby phones which are in TALK mode continuous transmission When these kind of signals are present on the power line it is possible that the Haibrain X 10 signals will not come through 5 The mains do not stop at the front door of your home Everything that is attached to mains nearby your home can have influence on Haibrain X 10 signals e g heavy machinery If you think that your system is influenced by devices out of your house it is advisable to install FD10 Phase Coupler Filter on each phase entering the house These filters will block signals coming into or going out of your house but will also match the impedance for the mains Hereby make your house Haibrain X 10 compatible for these units The FD10 s will not only filter but will also couple the phases please see 1 SMM31 7 SHUTTER SWITCH MICRO MODULE Program RED Button a ee BLACK CELL Light RT Indicator Shutter Switch Micromodule PHASE O NEUTRAL O FUNCTIONS e Makes your X 10 system invisible e Invisible installation built in behind existing switches or wall sockets The module works with all makes and types of switches which means it can be used in every interior and with all installations e Quick and easy to install and program e Transforms your existing 1 way standard rocker switch into a X 10 controllable switch e Micromodule with built in relay with two contacts for connecti2. switch the MicroModule against the back wall of the wall outlet behind all the wires e You are now able to program the MicroModule For more information see chapter Programming Install the 1 way standard rocker switch at its original SMM31 9 place after the MicroModule is programmed Please note due to heat generation apply no more than one module per flush socket central socket PROGRAMMING WARNING DO NOT FORGET TO TURN ON THE MAIN MASTER SWITCH PRIOR TO PROGRAMMING Programming the address The factory setting for the SMM31 is to address A1 Unlike most Haibrain X 10 Modules the SMM31 does not have code wheels To change the address the module needs to be set to the program mode Press and hold the Program button for 5 seconds indicator light Turns ON means entering Program mode Transmit the address command xx ON or XX OFF at this time the indicator light goes OFF Warning The MicroModule will leave the setup mode if it doesn t receive any commands within 30 seconds 10 O HAIBRAIN FREQENTLY ASKED QUESTIONS What is the reason for modules to switch on off spontaneously It is possible that a Haibrain X 10 System is installed at one of your neighbours using the same House Code To solve this problem try to change the House Code of your system or have FD10 Phase Coupler Filter installed at your incoming mains My modules will not respond to my controller Make sure
3. that the House Code on all Modules and Controllers are set to the same House Code A P My modules will not react to my remote sensor When you use a remote or sensor you should have at least one Transceiver CM15Pro or Haibrain X 10 Security Console installed in your house These components will translate the radio signals to the Haibrain X 10 signal on the power line Using several remotes and sensors you only need one central transceiver SMM31 11 Am able to increase the range of my remotes by using more Transceivers Yes you can use more than one Transceiver in your home when the range of your remotes is not sufficient The transceiver is using so called collision detection to prevent signals to be disturbed when more than one transceiver is transmitting The Transceivers will wait for a quite power line before transmitting their data To prevent your Haibrain X 10 System to become slow or to prevent dimming from becoming less smooth make sure that the transceiver units are placed as far away from each other as possible Do you have other questions that have not been resolved by the above information Please go to http www haibrain com 12 O HAIBRAIN TECHNICAL DATA Supply voltage Power Consumption Maximum Load Control Load QTY Signal sensitivity X 10 Key codes Input switch Use in 3 phase installation Connections control lines in wall junction box Ambient temperature Dimensions
4. 230VAC 10 10 50 Hz 1W 200W for motors One better than 25 mVpp at 120 kHz Off 1 On 2 Dim Bright 1 way standard rocker switch FD10 3x or FKX40 necessary Wire for a standard rocker switch and connecting clamps for phase neutral and motor not more than 1 meter between the micro module and the switch 50mm 10 C tot 50 C Operation 43 25mm x 47mm x 18 9mm Specifications may be modified without prior notice SMM31 Environmental Information for Customers in the European Union European Directive 2002 96 EC requires that the equipment bearing this symbol on the product ENEN and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities waste disposal service or the shop where you purchased the product 14 HAIBRAIN DECLARATION OF CONFORMITY Hereby Haibrain BV declares that this SMM31 is in compliance with the essential requirements and other relevant provisions of the following D
5. SMM3T Shutter Switch Micromodule 20458 20120313 SMM31 h a b ra n ALL RIGHTS RESERVED HAIBRAIN only brilliant ideas TABLE OF CONTENTS SAFETY WARNINGS er eire nri nri 4 HOW DOES HAIBRAIN X 10 5 ADRESSES is SIGNAL RANGE 5 rre err rrr 6 SHUTTER SWITCH MICRO 8 FUNCTIONS INTRODUCTION INSTALLATION eerie eee ida nere enin PROGRAMMING sux FREQENTLY ASKED QUESTIONS essere TECHNICAL ont innere rere DECLARATION OF CONFORMITY COPYRIGHTS SMM31 3 SAFETY WARNINGS The wiring of your electrical installation is live 230 V and extremely dangerous Never connect the module when plugged into the mains Always turn off the main switch before starting the installation This product is for professional use and should be installed by a certified installer To prevent short circuits this product should only be used inside and only in dry spaces Do not expose the components to rain or moisture Do not use the product close to a bath swimming pool etc Do not expose the components of your systems to extremely high temperatures or bright light sources In case of improper usage or if you have altered and repaired the product yourself all guarantees expire Haibrain does not accept responsibility in the case of improper usage of the product or when the product is used fo
6. Up to a maximum of 256 different addresses can be preset These are subdivided into a so called HouseCode A to P incl and a UnitCode 1 to 16 incl The HouseCode can also be set on the controllers so that the controllers and modules become part of the same system The address can be set either using code dials or by pressing buttons depending on the type of module The Haibrain X 10 System uses standard commands which control all units with the same HouseCode at the same time e g all lights on all units off etc SMM31 5 SIGNAL RANGE Range of Haibrain X 10 signals over the Power Line and how to increase the range The Haibrain X 10 System is based on power line communication The range of the Haibrain X 10 signals very much depends on the local circumstances On average the range is a cable length of 80 meters If you have difficulties with the range of your Haibrain X 10 signals please pay attention to the following facts 1 When more than one phase is used for your electrical system it is necessary to couple these phases for the Haibrain X 10 signals For coupling you can use FD10 Phase Couplers Filters You only need to install a Phase Coupler Filter when your wall outlets and light switches are divided over more than one phase more than one group is no problem For bigger buildings or longer distances we advice you to use an active repeater instead of passive FD10 s 2 It is possible that Haibrain X 10 signals ar
7. e attenuated by devices and lights which are connected to the power line In a normal home situation this effect is negligible the Haibrain X 10 system is using active gain control to eliminate the effects However it is possible that a particular device in your house is attenuating the signals so much that the range of Haibrain X 10 signals is decreased significantly When you have range problems it is wise to try to locate the device which is attenuating the signals simply by unplugging devices from the power line and testing the differences in range for your Haibrain system When e g your conclusion is that e g your computer monitor is attenuating the signal you can use a FM10 6 O HAIBRAIN Plug in Filter between the power line and the monitor to eliminate the effects Known devices which can cause attenuation are PC Monitors PCs with heavy internal power supplies Old Televisions Copiers Fluorescent Lights Gas Discharge Lamps Energy Saving Lamps 3 Some old devices are able to disturb the signal by transmitting noise on the power line Because the Haibrain X 10 signals are transmitted on 120 kHz only noise on or near this frequency will have influence on the range When you use a FM10 Filter to connect this device to the power line the noise will be filtered 4 The Haibrain X 10 protocol has several mechanism to avoid modules to be switched on or off by other sources than your Haibrain X 10 Controllers However it
8. irectives Directive 2004 108 ec of the european parliament and of the council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility Directive 2006 95 EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits Directive 2002 95 EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment SMM31 15 COPYRIGHTS Copyright and all other proprietary rights in the content including but not limited to model numbers software audio video text and photographs rests with Haibrain B V Any use of the Content but without limitation distribution reproduction modification display or transmission without the prior written consent of Haibrain is strictly prohibited All copyright and other proprietary notices shall be retained on all reproductions 16 O HAIBRAIN haibrafn only brilliant ideas
9. ng a 230V motor be operated remotely with an X 10 signal or locally fully open closed or on every interim position Lowers in combination with the CM15Pro computer interface the sun blinds automatically during the day in places where the sun shines inside This way you protect your furniture against the sunlight keep the house cool and simulate that you are at home e MicroModule uses one way X 10 communication 8 O HAIBRAIN INTRODUCTION n This unit allows a motorized blind to be controlled either manually from a 1 way standard rocker switch connected to the unit or remotely by serial Haibrain X 10 Powerline messages sent from a suitable controller When controlled serially the blind can be made to go to intermediate settings in addition to fully up or fully down with dim and bright commands INSTALLATION Switch off appropriate mains fuse and master switch Important 230V 50Hz 1A per channel e Toinstall the SMM31 neutral and phase are required at the installation point e the wall switch out of the wall box Disconnect all wires from the switch Pull an additional Neutral wire if it is missing Connect the phase and neutral wire to the L and N terminals of the micromodule Connect the terminal 1 of SMM31 to Motor Down the terminal 2 to Motor Up e Connect the thin Black and Red wires of the built in module to the 1 way standard rocker
10. r purposes other than specified Haibrain does not accept responsibility for additional damage other than covered by the legal product responsibility This product is not a toy Keep out of reach of children Do not open the product the device may contain live parts The product should only be repaired or serviced by a qualified expert Automatic switching devices provide comfort but can also be dangerous They can surprise people or can ignite clothing hanging over an electric heat source Please be careful and take appropriate measures to avoid accidents HAIBRAIN HOW DOES HAIBRAIN X 10 WORK Haibrain X 10 components use the existing mains wiring to communicate using Haibrain X 10 signals You can build a complete system using the three different kind of components of the Haibrain X 10 System 1 Modules These components will receive Haibrain X 10 signals and will switch or dim the attached lamp or appliance Examples of these modules are lamp modules and appliance modules These are available as build in micro DIN rail and plug in modules 2 Controllers These components will transmit Haibrain X 10 signals and thus will control the Modules 3 Transmitters Wireless components like remotes The signals of these components will be received by a controller with transceiver functionality IRRF 7243 TM13 CM 15Pro The Transceiver will translate the signals into Haibrain X 10 signals on the power line ADRESSES
Download Pdf Manuals
Related Search