Home
Manual - White Light
Contents
1. a Consultant Clinical Scientist and Head of the Clinical Engineering Department of Medical Physics amp Bioengineering at the Royal United Hospital Lindsay kindly gave us this advice The operation of heart pacemakers will be affected by the close proximity of a magnet Magnets can set a pacemaker working in a way that is not suitable for the pacemaker user and that might affect their health This change will stop when the magnet is removed She added The background to this is that magnets are used to put pacemakers into a mode of working that does not respond to the patient s own heart rhythm We regularly use magnets in our pacemaker clinics to change the working of the pacemaker to see how it is operating Each pacemaker manufacturer uses the magnet response of a pacemaker ina different way so it is impossible to be more precise than the above statement Some manufacturers have a response that makes the pacemaker pace the heart at 100 beats per minute or faster The PinPoint User Manual V1_0 9 pacemaker will not usually synchronise with the natural heart beat when a magnet is applied Although in 20 years experience of putting magnets on pacemakers have never had a problem it is theoretically possible to trigger a life threatening heart rhythm by doing so Implantable cardioverter defibrillators ICDs The following information is taken the from the website link http www heart org HEARTORG Conditions Arrhythmia Pre
2. the flashing becoming distracting as heat generated from the heads will be minimal e Switch off the charger unit and unplug once fully charged DO NOT use any charger other than the unit supplied with the PinPoint When using a charging flight case ensure the unit is pushed fully down onto the charging plate so the connections are fully made The bodywork magnetic base provides one of the terminals so ensure this has a good connection with the charger plate by removing any dirt labels or other insulating materials Ensure the charger hole is free of objects and that the gold terminal plate in the end of the hole is visible for contact to be made inside the unit PinPoint User Manual V1_0 5 The unit possesses three modes to change brightness and set the unit on up to 512 different channels a Amanual mode capability for operation from the Power Switch if no wireless is available b Bluetooth Low Energy with suitable control devices such as tablets and smartphones This allows Channel Setting and brightness slider control operation with the CORE Apps c Wireless DMX Receiver receive only where fitted for control from a lighting desk on different channels This is an option Basic use can be made with only Bluetooth and manual control Function Modes Bluetooth channels have the same value as Wireless DMX channels to allow adjustment between devices All three modes run concurrently with the last command taking priority So if the
3. Information System Compliance CORE Lighting Limited declares that this product conforms to the specifications listed in this manual following the provisions of the European R amp TTE directive 1999 5 EC Restrictions on Hazardous Substances ROHS 2002 95 CE Electromagnetic Compatibility 2004 108 EC Safety EN 60950 Technical requirements for radio equipment EN 300 328 CAUTION This equipment is intended to be used in all EU and EFTA countries Outdoor use may be restricted to certain frequencies and or may require a license for operation Contact local Authority for procedure to follow FCC amp Industry Canada Statement for Radio Compliance W DMX Receiver We CORE Lighting Limited Prindion House Kingsmill Lane Painswick Gloucestershire GL6 6SA declare under our sole responsibility that the product FCC ID VQT WDMXOEMPCBF Model W DMX OEM PCB F complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation To assure continued compliance any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15
4. USER MANUAL CORE Lighting Limited CORE PinPoint Battery Wireless PinSpot Lithium Battery with Bluetooth BLE amp Wireless DMX Contents RS itis sath ica et od Ee aea 1 Be Egte N EE ED HE EE 2 Product Modification siese see ds ee ek Ee ee ge de ENE AK ee ee dd we ek Ke Ka ee ee ed Ke 2 Safety Information iseer ek KEN Ek N N Ee ee N eN EK Ke ek Ge we WRK N EE Ee We ed 2 Before You Bet iese dee Si Eed N kk ee Ke ed N EE GN We Ke El ee ee dd 3 Product Overvie Wise K ede Ke NAN AN ad ee Ka Me NN Sue ee N 3 Features Include sisie nige design n eie de es we Ge de Ge Nee sei d 3 SEU A EE RE E E E A 3 Geltlinag Started siisii aaaea KA N ana Es EA N KEN es GE SEN Ge Ge Ed 4 PHAPOI Key Elemente ir ads iis sind oes ke Ede nite nis de ede ene de de oe Res DEE 4 ae EE EE OE EE EE EE EE EE OE Ee 4 Ventilation and Mounting eiser eke EE REKE EE NEER EE REKE Ee ek ee Nek ee ee ee ee ese 4 SION oe seke eise aera ie cana a ela ie ee se ed GE 5 Power amp Manual Intensity sees ese ie ie ee ee eo Ee ee Ge in 5 CHAIQUIG sessies Eks GE dee ke Ke Ge EA Ede ke dk de le N RA EA Ee AE 5 Function Modes iss sesse eds ee es ee Ke ke ee ge RENE Ak ee ee de ee ke ad Ge ee ed 6 Mechanical sesse se N EEN GE ee be ek N kk ve KNEG 8 DIMENSIONS AND AE EE EE OE EA ON EE N NE EN 8 Safety Secondary FIXING Point eise sesse EKKE ERA AA EER RE EE ERA AE ERA RE 8 PNG d SEE EE EE EE EE EE 8 Safety Information on strong magnets se
5. f it appears damaged in any way DO NOT operate this fixture where the ambient temperature exceeds 45 C DO NOT place near heart pacemakers or Implantable Cardioverter Defibrillators ICDs authorised distributor In the unlikely event that your product develops a fault please contact your local dealer or A Do not attempt to repair yourself unless specifically instructed by CORE Lighting Ltd PinPoint User Manual V1_0 3 Getting Started PinPoint Key Elements 2 X N LED Emitter amp lens Gooseneck focus adjustment Radio End Cap i Anti roll Foot Battery Body Anti roll Foot with safety point l Magnet Attachment Charging Base Charger Base Charging Plate The battery charger may be included as an accessory for individually purchased fixtures or built into the flight case for multiple charging fixtures In each case the supply has an input voltage range of 100 240 VAC at 50 60Hz Power Ensure the product is used only with correct voltage and frequency of mains supply Never connect the charger or charging case to a dimmer circuit even when a dimmer has been configured for non dim or switched operation OP Ventilation and Mounting Always use the product in a safe position and ensure there is enough room around it for ventilation A Keep the charging case lid open during charging this allows escape of heat PinPoint User Manual V1_0 4 Operation OP Power amp Manual Intensity e Push a
6. ised dealer This Warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installation or attempted repair by anyone other than CORE Lighting or a CORE Lighting dealer or authorised service agent which is authorised to do CORE Lighting warranty work Any unauthorised repairs will void this Warranty This Warranty does not cover products sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER CORE LIGHTING SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FORA PRACTICAL PURPOSE Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other statutory rights which vary from state to state or country to country For any service in or out of warranty please contact your dealer PinPoint User Manual V1_0 11 Compliance
7. ium magnets on people or animals quite the reverse PinPoint User Manual V1_0 10 CORE Lighting Limited CORE Lighting warrants this product to be free from defects in materials and workmanship subject to the terms set forth below Warranty CORE Lighting will repair or replace at CORE Lighting s option this product or any defective parts in this product The standard warranty period is 24 months from date of purchase excluding battery pack which is 12 months although this period may vary from country to country If in doubt consult your dealer and ensure that you retain proof of purchase To obtain warranty service please contact the CORE Lighting authorised dealer from which you purchased this product If your dealer is not equipped to perform the repair of your CORE Lighting product it can be returned directly to CORE Lighting with carriage being paid at your own expense You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Providing the product is found to be faulty CORE Lighting will pay for return carriage Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the warranty period must be presented to obtain warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a CORE Lighting author
8. lighting desk is changed followed by a slider change on the Bluetooth App the lighting desk level will be used first this will be followed by the value from the Bluetooth App This is useful for a lighting operator who sets a level on a lighting desk globally then wanders around with a tablet or smartphone to set individual local levels at the subject positions on different channels The three modes of Operation are accessed through the Power Switch This mode allows the fixture to be dimmed in units of 20 by repeated pressing of the Power Switch This switch also allows the unit to be turned OFF into SLEEP mode Channel When the unit is ON push and hold the Power Switch for a few seconds until the unit head starts to Set flash on and off just longer than once every second This is Channel Setting mode From a Bluetooth enabled tablet or smartphone with the CORE PinPoint App installed and running push the desired channel number button on the screen to which the unit is to be paired If successfully registered flashing will stop and the unit may now be controlled from the App moving the on screen slider associated with the relevant channel button If unsuccessfully paired try again until success is achieved maybe moving closer to the unit if necessary to gain stronger signal Up to 512 channels are available Multiple units may be addressed to the same channel or individual units set to different channels All units in Chan
9. nd hold the power button for gt 1 second to switch the unit ON e Push again to reduce the intensity by 20 e Push again for a further 20 e Continue until the unit switches OFF There are 5 steps to OFF e Infact the unit is now in SLEEP mode The processor will continue to run with a very tiny current which will be maintained for many weeks months from a full battery but the main circuit is turned off Charging e Turn the unit OFF before connecting to the charger The charger should turn the unit off in any event after a couple of seconds of being attached and powered e Only use the supplied external charger or charging flight case to prevent damage to the units e Plug the case or charger into the grid mains wall socket e The unit s to be charged should be attached onto the charger plate s The unit magnetically attaches to this plate which retains the unit onto the contacts and holds in place during transport for flight case chargers Ensure the charging pin is fully engaged in the bottom of the unit e Whilst charging the LED head will flash very briefly every few seconds The process will take several hours Overnight is best e Once fully charged the LED head will stop flashing e For best results on battery longevity recharge battery fully before storage e When charging in the charging case it is best to ensure the case lid remains slightly open to disperse heat although the lid may be closed onto the LED heads to prevent
10. nel Set mode at any one time are likely to respond to that one Button push on the App so multiple channels will need to be paired in sequence and not together Once done the unit may be used or switched off by pushing the Power Switch The channel set here with Bluetooth also becomes the same channel for Wireless DMX Wireless With the unit in Channel Set mode above and the lamp head flashing before accepting a channel DMX push and hold the Power Switch for a few seconds until the LED head stops flashing and goes solid WDMX but dim to 20 maximum This is WDMX Pairing Mode and allows the unit to be paired with a Pairing WDMX transmitter plus it disconnects this unit from any other transmitter it was previously paired with Note WDMxX pairing also resets the channel number to 1 as a limited factory reset so if setting up for a new job it s advisable to do WDMX pairing first before setting channel otherwise the setting will be lost To link to the new transmitter briefly push the button on the transmitter for 1s then let go If successfully paired the head will start to flash whereby the unit is back in Channel Set mode This allows units to be set using the Bluetooth device mentioned above and below Note all devices in Channel Set mode will be set to the same channel number at this point For creating multiple units on different channels the Channel Set function alone will need to be repeated for each channel PinPoi
11. nge of up to 300mm the one on the desk will leap and accelerate with considerable force which on impact will cause bruising blood blisters cuts or crushing Always consider the magnetic implications of where you place magnets Magnetically sensitive Items Neodymium magnets are very much stronger than ordinary magnets Keep a safe distance 300mm between the magnets and all objects that can be damaged by magnetism These include mechanical watches heart pacemakers CRT monitors and televisions credit cards diskettes and other magnetically stored media such as video tapes hard drives and older generation i pods Heart Pacemakers The operation of heart pacemakers will be affected by the close proximity of a magnet Magnets can set a pacemaker working in a way that is not suitable for the pacemaker user and that might affect their health This change will stop when the magnet is removed It is possible that a heart pacemaker will be affected by the close proximity of a magnet as they can cause pacemakers to operate in a mode that does not respond to the user s own heart rhythm The way a pacemaker responds to a magnetic field differs between manufacturers and therefore people with pacemakers should not put strong magnets close to their chest We sought advice from a specialist and the following information represents our best knowledge regarding how heart pacemakers are affected by magnets Lindsay Grant BSc CEng FIET CSci FIPEM ARCP is
12. nt User Manual V1_0 6 At the time of going to press the following Android devices were known to be working but it was also known that others were awaiting latest Bluetooth Low Energy hardware to be released on latest models which would include the latest Bluetooth software stack and hardware configuration Google Nexus 6 Google Nexus 9 The above devices loaded with CORE PinPoint App downloaded from Google Play Store An iOS Apple version of the app CORE LightDesk was currently in development nearing completion to work on numerous versions of smartphones and tablets Please check with CORE about availability This will be press released when available published on the company website and announced on social media including CORE s Facebook page Wireless Solutions W DMX compatible only Devices may be used to control each PinPoint such as Wireless Solutions F 1 transmitter attached to a lighting desk Wireless Solutions Micro transmitter lower powered CORE ColourPoint uplighter in Master mode CORE Point15 uplighter in Master mode CORE Point20 uplighter in Master mode CORE Point30 architectural unit in Master mode For successful linking the receiver must fulfill the following conditions Distance to transmitter in free air e Less than 50m for Micro model transmitter e Less than 200m for F 1 transmitter Position above obstacles e g crowds and tress Ci Pairing to a transmitter is remembered after power off or the bat
13. ntain and reduce the impact on human health and the environment The consumer must contact their local authority or retailer for information concerning disposal of their products CORE Lighting provides a take back facility for batteries used within CORE Lighting products although the expense for transport remains the liability of the consumer Please contact CORE Lighting directly if this service is required PinPoint User Manual V1_0 13
14. of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures e Reorient or locate the receiving antenna PinPoint User Manual V1_0 12 e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help RF Exposure Warning for North America and Australia This unit does not transmit therefore no consideration is currently necessary for RF transmission effects WEEE amp RoHS Statement The European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE requires that products must not be disposed of the normal unsorted municipal waste stream Appliances must be collected separately in order to optimise the recovery and recycling of the materials they co
15. re to comply with this information may cause damage to the product third party Critical installation or usage information equipment or cause harm or injury Important installation or usage information Failure to comply with this information may cause the product to operate incorrectly Very important For safety reasons please read the Safety Information for Magnets at the end of this manual concerning the effect of magnets on heart pacemakers and Implantable Cardioverter Defibrillators ICDs Also review for the safety of using strong magnets Note This product contains a lithium ion battery When transporting this equipment on aircraft please consult IATA Packing Instructions 967 and CORE Lighting Ltd for further information Note the capacity of the battery is less than 100Wh which is currently less than the size required for the extra notifications and processes relating to air transport although the guidelines should be reviewed more thoroughly if shipping in bulk PinPoint User Manual V1_0 2 Before You Begin CORE PinPoint is a single LED pin spot light with magnetic base attachment It is battery powered and rechargeable has wireless control from Bluetooth and Wireless DMX W DMX and head focus through an adjustable gooseneck The unit is also IP65 rated for outdoor use It s ideal for lighting table centres art pieces enhancing artefacts or simply providing quick and easy task lighting The unit runs for over 8 ho
16. sse ee RE ER REGEER RR EER RR EE EE ee ee 9 TEL OE EE EE 11 Compliance Information asses ss eN EKS NKR ERG NEER Add NAN KA Ed EER RAN RA Rd GN EN EN 12 SY SICH COMPA CE ee EG ek ee N EE SN ee ee oe ea Ge ed ed 12 FCC amp Industry Canada Statement for Radio Compliance sesse sesse ee 12 WEEE amp RoHS Slatemef sissies sere es eie ei ie ee N ne biol ee N eed 13 PinPoint User Manual V1 0 1 Disclaimer CORE Lighting Limited believe the information in this manual is accurate and complete however assumes no responsibility for any error or omissions within this document or any other documentation accompanying the product We reserve the right to revise this document at any time Please see www corelighting co uk support to download latest version Product Modification This CORE Lighting product has been designed and manufactured to meet the strict requirements of UK EU and International safety regulations Any unauthorised modifications to the product including replacement of parts with non standard parts could compromise safety and result in the product being non compliant with relevant standards There are no user serviceable parts within this product Safety Information Important safety information is contained within this manual Please read all instructions fully prior to installation and use of the equipment Internationally recognised symbols are used within the document to highlight important messages as follows Failu
17. tery is depleted This allows the system pairing to be set up in a warehouse and the whole system simply switched on at the site which makes deployment very simple PinPoint User Manual V1_0 7 Mechanical Dimensions mm 280 Safety Secondary Fixing Point Hole 2 7 dia Flight Case PinPoint User Manual V1_0 8 Safety Information on strong magnets PinPoint product CORE lighting Advice re handling of product with strong magnet Information supplied by our manufacturer of the Neodymium Magnet used in this product Dangers for children Ensure that children are not allowed to play with magnets Fingers can be crushed between the powerful magnets If they place them onto a CRT television screen or CRT computer monitor screen permanent damage can occur as colours will become permanently distorted Crushing When larger magnets are brought close enough together they can have a surprising amount of power This risks involved are directly proportional to the size volume of the magnet and the power grade of the magnet 4cm3 risk of blood blisters Fingers are quickly caught between them which can cause blood blisters These magnets can jump through very large distances the biggest danger comes from two magnets spaced apart which as they move closer can suddenly leap together with extreme speed and force If you have a magnet in your hand and another is placed on your desk and you accidentally come within the magnetic ra
18. urs at full power on a single charge which can then be dropped in a charging case with other units ready for next use The CORE PinPoint is designed manufactured and supported in the UK and has local distributor support Product Overview Features include High powered 300lumen warm white LED at 3000K CCT illuminates from 2 storeys high Tight 4 5 degree spot beam angle with flexible gooseneck focus Lithium lon Battery superior charging and weight just 650g Strong magnet to attach unit to railings ceiling metalwork etc Side feet allowing body to rest on a shelf Bluetooth control of brightness and channel to enable separate control of individual units Units controlled from an app on a tablet or phone Latest Google Android devices and iOS soon Wireless DMX wireless receiver 2 4GHz W DMX compatible IP65 casing for outdoor events Designed and Manufactured in the UK Safety AVOID direct eye exposure to the light source when illuminated DO NOT submerge this product in water or expose to excessive water spray DO NOT hang this product other than by the means indicated in this manual DO NOT leave any flammable material near product whilst operating or charging ALWAYS use the supplied charger or charging case ALWAYS ensure the charger is connected to the specified voltage ALWAYS ensure the charging case lid is open whilst plugged into mains supply NEVER connect this product or charger to a dimmer pack DO NOT operate this fixture i
19. ventionTreatmentofArrhythmia Devices that may Interfere with Implantable Cardioverter Defibrillators ICDs UCM 448464 Article jsp Magnets Magnets in general may or may not affect your ICD operation so it is best to avoid close and prolonged contact with any of them Magnets can activate a switch which can prevent the ICD from delivering treatment therapies such as life saving shocks e Keep magnets at least 6 inches 15 cm from the ICD site e Avoid magnet therapy such as used in bracelets and necklaces that may be worn for extended periods of time near the ICD e You may not know what does or doesn t have a magnet in it If you feel any interference move away from the source or turn it off if possible Nickel allergies Only relevant if the magnet is removed from inside the PinPoint unit Our Neodymium magnets are nickel plated Nickel isa metal which can cause an allergic reaction in some people Nickel allergies can be acquired through long term contact with objects that release nickel As a precaution avoid long term contact with nickel plated magnets e g jewellery and totally abstain from contact with nickel plated materials if you already have a nickel allergy How much or little it takes to trigger a nickel allergy is debatable Euro coins contain 25 nickel Effects on people Millions of people worldwide wear Neodymium magnets to promote health and well being We have found no evidence at all of detrimental effects of Neodym
Download Pdf Manuals
Related Search
Related Contents
Samsung J1055AV User Manual INFOS MAG SUPRE MANUAL-2008 Sony SRX-R105 User's Manual Copyright © All rights reserved.
Failed to retrieve file