AMI300 Series User Manual
Contents
1. AMI300 8 Parts Description Part NO Description Part NO Description 1 Name panel 2 Top chassis 3 Storage cable 4 HDD 5 HDD DVD RW bracket 6 Anti Vibrate grommet 7 Thermal PAD 8 Extension heat sink 9 MI910E 10 Rear panel 11 Bottom chassis 12 Mounting rail 13 Slim DVD RW 14 Heat pipe 15 D450 16 ATX power extension cable 17 Front panel 18 USB extension cable 19 Control panel cable 20 IB881 SW Board 21 DC extension cable 18 Driver Installation Please refer correspond mainboard user manual to install the driver properly BIOS Setup Please refer correspond mainboard user manual to configure BIOS setting 192. Copyright 2008 IBASE Technology INC All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of IBASE Technology INC IBASE Products and corporate names mentioned in this manual may or may not be registered trademarks or copyrights of their respective companies and are used for identification purposes only All trademarks are the property of their respective owners Every effort has been made to ensure that the contents of this manual are correct and up to date However the manufacturer makes no guarantee regarding the accuracy of its contents and reserves the right to make changes without prior notice Table of Contents Pal ALLL E T T T A E E daususudaateoaeunsausavens 6 COMPONENES sorniroiissr irtiri natin i er teinar iien RAEE EE AEE AE a 7 AKAA EREE E AEE E TT 7 Rear View AMI300 9 gt ccccsiccscscenss seis oi ccncteebadevissndewesee donstesuecacecbedenduncedeseasbadendies Sosceacbades 8 Rear View AMI30028 iiscccsecccscoiads eid tecee seals seddeccessdedsanesssecescevebeacediccdestcdedivecdstecsudbacds 10 SDOCIICOCION nener e aa a a a a a aaa a e aa aS 12 Mounting AMI300 to the WAll wesissciicsccaccsssesticeotadacccasvecdicecedscacauadescontensce
3. BASS REAR SIDE LINE IN FRONT MIC Analog audio output connector Please refer M B manual to connect analog audio signal out to get stereo or 5 1 channels signal DC IN The supplied power adapter converts AC power to DC power for use with this jack Power supplied through this jack supplies power to the system To prevent damage to the system always use the supplied power adapter Rear View AMI300 8 Refer to the diagram below to identify the components on this side of the system O MWS SVIDEO COM 1 Eai SLAN O gt E B iy umen o L N IN mor e DC IN W US O o KIB TV OUT USB 1294 SPDIF USB Te M S The PS 2 mouse port is use to connect PS 2 mouse K B The PS 2 keyboard port is use to connect PS 2 compatible devices such as keyboard MSR and scanner S VIDEO Super Video is a Y C analog video signal output port that carries luma and chroma signals to any display which support this interface such as projector TV TV OUT Composite Video port RCA connector is format of an analog television picture only signal to any display which supports this interface such as projector TV COM1 Communication or serial port one is compatible with RS 232 interface VGA Video Graphic Array VGA port supports a VGA compatible device such as a monitor or projector The system d
4. ausing serious damage to the product Slots and openings on the chassis are for ventilation Do not block or cover these openings Make sure you leave plenty of space around the system for ventilation Never insert objects of any kind into the ventilation openings This system should be operated from the type of power indicated on the marking label If you are not sure of the type of power available consult your dealer or local power company Use this product in environments with ambient temperatures between 0 C and 45 C If you use an extension cord make sure that the total ampere rating of the devices plugged into the extension cord does not exceed its ampere rating Care during use Do not walk on the power cord or allow anything to rest on it Do not spill water or any other liquids on your system When the system is turned off a small amount of electrical current still flows Always unplug all power and network cables from the power outlets before cleaning the system If you encounter the following technical problems with the product unplug the power cord and contact a qualified service technician or your retailer gt The power cord or plug is damaged gt Liquid has been spilled into the system gt The system does not function properly even if you follow the operating instructions gt The system was dropped or the cabinet is damaged Lithium lon Battery Warning CAUTION Danger of explosion if battery is incorr
5. dasuratiacwes 13 Wall mounting requirements ssessssssssesosssesossssoossssoosesoossseooseseoossssossessoosessessessosses 13 Selecting the location ws cisecscsvcccdesvadedsdeeseac escddescaucdaladecceacdescisesegavsacedsssssecsvecscbsdavdeacds 14 Exploded view of the AMI300 assembly AMI300 9 ccsssccssssccnsssecnsscecasscsaaeses 15 Parts description ise sesedsseceded cu sbeccssccseicdswsencd se ENIES EPON EA ONASIN EENET E EASA ONNAN EENET EEan 16 Exploded view of the AMI300 assembly AMI300 8 ccsssccssssccrssceccsscesesscseneses 17 Parts Description renis eony asaos e ehor Epean Errr ONERE Eo TAn seacedscs esbediscedekedsedoacdi sconediscedekcasedeasee 18 Driver Inst llation socessetuccusted woseesseucteinsnatuchsodueneptesnesdenedoebennoratudssoduteweteracpesneenedetnee 19 BIOS SCtUp o EA E E T E T 19 Safety Information Your AMI300 8 9 is designed and tested to meet the latest standards of safety for information technology equipment However to ensure your safety it is important that you read the following safety instructions Setting up your system Read and follow all instructions in the documentation before you operate your system Do not use this product near water Set up the system on a stable surface or secure on wall with the provided rail Do not secure the system on any unstable plane or without the rail Do not place this product on an unstable cart stand or table The product may fall c
6. ead write data from the disc with proper software Rear View AMI300 9 Refer to the diagram below to identify the components on this side of the system DVI E Lw L PE Regs en gt anoone0n OP Ln a B M S The PS 2 mouse port is use to connect PS 2 mouse K B The PS 2 keyboard port is use to connect PS 2 compatible devices such as keyboard MSR and scanner COM1 Communication or serial port one is compatible with RS 232 interface VGA Video Graphic Array VGA port supports a VGA compatible device such as a monitor or projector The system default display output port LAN The eight pin RJ 45 LAN port supports a standard Ethernet cable for connection to a local network USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many devices to run simultaneously on a single computer with some peripheral acting as additional plug in sites or hubs DVI The Digital Visual Interface DVI port supports a high quality VGA compatible device such as a monitor or projector to allow viewing on a larger external display SPDIF Plug a standard SPDIF optical audio cable into this connector for digital audio transfer
7. ectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions NO DISASSEMBLY The warranty does not apply to the products that have been disassembled by users Accessories CE ws a Power Cord x 1 b M B Manual x 1 D c DriverCDx 1 _ Sssssossssossos d Power Brick x 1 e Mounting Rail Screw x 6 f Mounting Rail x 2 Components Front View Refer to the diagram below to identify the components on this side of the system O o oO PWR HDD RST ON USB Fovo r o eene o PWR The power LED illuminated when system been power on HDD The hard disk LED blinks when data is being written into or read from the hard disk drive RST The reset switch allows reset the system ON OFF The power switch allows powering ON and OFF the system USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many devices to run simultaneously on a single computer with some peripheral acting as additional plug in sites or hubs DVD RW Slim tray type DVD RW support most CD and DVD in the market You can r
8. efault display output port 10 LAN The eight pin RJ 45 LAN port supports a standard Ethernet cable for connection to a local network USB The USB Universal Serial Bus port is compatible with USB devices such as keyboards mouse devices cameras and hard disk drives USB allows many devices to run simultaneously on a single computer with some peripheral acting as additional plug in sites or hubs 1394 IEEE 1394 interface connector SPDIF Plug a standard SPDIF optical audio cable into this connector for digital audio transfer LINE IN The stereo headphone jack 3 5mm is used to connect the audio signal into system to record or bypass it to storage or LINE OUT LINE OUT The stereo audio jack 3 5mm is used to connect the system s audio out signal to amplified speakers or headphones MIC The microphone jack is designed to connect the microphone used for video conferencing voice narrations or simple audio recordings DC IN The supplied power adapter converts AC power to DC power for use with this jack Power supplied through this jack supplies power to the system To prevent damage to the system always use the supplied power adapter Specification 199 W x 77 4 H x 232 D mm 7 83 x 2 97 x 9 13 Power Supply 80W DC adapter 0 C 45 C 32 F 113 F 5 95 45 C non condensing HDD 0 25g 5 500Hz random operation This specification is subject to change without prior notice 12 Mounti
9. hod 2 Drywall walls Drywall over wood studs is acceptable Mounting to a solid concrete or brick wall Mounts on a flat smooth surface Selecting the location Plan the mounting location thoroughly Locations such as walkway areas hallways and crowded areas are not recommended Mount the unit to a flat sturdy structurally sound column or wall surface The best mounting surface is a standard countertop cabinet table or other structure that is minimally the width and length of the unit This recommendation reduces the risk that someone may accidentally walk into and damage the device Local laws governing the safety of individuals might require this type of consideration 14 Exploded view of the AMI300 assembly AMI300 9 9 00V o y E Parts description Part NO Description Part NO Description 1 Name panel 2 Top chassis 3 Storage cable 4 HDD 5 HDD DVD RW bracket 6 Anti Vibrate grommet 7 Thermal PAD 8 Extension heat sink 9 Screws for SB heat sink 10 ID392 DVI board 11 MI910E 12 Rear panel 13 Bottom chassis 14 Mounting rail 15 Slim DVD RW 16 Southbridge heat sink 17 Heat pipe 18 D450 19 ATX power extension cable 20 Front panel 21 USB extension cable 22 Control panel cable 23 IB881 SW Board 24 DC extension cable 16 d 00090 17 Exploded view of the AMI300 assembly
10. ng AMI300 to the Wall Using attached mounting rail you can install AMI300 on wood drywall surface over studs or a solid concrete or metal plane Ensure the installer uses at least four M4 length 8mm screws to secure the system on wall Six M4 length 8mm screws are recommended to secure the system on wall Fasteners are not included with the unit and must be supplied by the installer The types of fasteners required are dependent on the type of wall construction Choose fasteners that are rated either Medium Duty or Heavy Duty To assure proper fastener selection and installation follow the fastener manufacturer s recommendations Wall mounting requirements Note Before mounting the system on wall ensure that you are following all applicable building and electric codes When mounting ensure that you have enough room for power and signal cable routing And have good ventilation for power adapter The method of mounting must 13 be able to support weight of the AMI300 plus the suspend weight of all the cables to be attached to the system Use the following methods for mounting your system Mounting to hollow walls Method 1 Wood surface A minimum wood thickness 38mm 1 5in by 25 4 cm 10in of high construction grade wood is recommended Note This method provides the most reliable attachment of the unit with little risk that the unit will come loose or require ongoing maintenance Met
Download Pdf Manuals
Related Search