User Manual
Contents
1. weight Voltage 100V 240V 50 60Hz Fuse T 3 0A Power consumption 85W Light source 8W x 7pcs 4 inl RGBW quad color LED Dimension 173 x 173 x 249 mm Weight 3 6 kg Pan Tilt 540 180 Power sockets IEC XLR sockets 3 pin XLR IN OUT 3 How To Set The Unit The main functions are as below 3 1 Control panel ADDR 001 512 ms 0 8 E o fore Display Shows the various menus and selected functions SOUN Button OFF SENS 000 255 MENU Selects the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions Mains input TED Connection to the power supply BALA YES For DMX 512 linking Use a 3 pin XLR cables to link to the controller or to i other units PAN INVERT 3 2 Main Functions TILT INVERT NO To select any of the given functions press the MENU button up to where TEST the required function is showing on the display Select the function by VER pressing the ENTER button and the display will blink Use the DOWN and UP buttons to change the mode Once the required mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MDD DMX Address Setting MEN f it f i k to the main OJ i OU SSS ene Wale er Onenmbete to de acs Press the MENU button to select 200 Press the ENTER button and the menu display will blink Use the DOWN2. Equinox Fusion 50 User Manual Contents 1 2 J 4 D 6 Safety Instructions Features amp Specifications How To Set The Unit How To Control The Unit Troubleshooting Fixture Cleaning 1 Safety Instruction Please read the instructions carefully as they include important WARNING information about installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this Unpack and check carefully that there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of the power Supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect the mains power before replacement or servicing Make sure there are no flammable materials close to the unit while operating as they may cause a fire hazard Always use a Safety cable when installing this unit Do not carry the unit by its head only always carry it using the base The maximum ambient temperature is to 40 Don t operate it where the temperature is higher than this In the event of a serio
3. U button for one second or wait for one minute to go back to the main menu Q bf L Dimmer Calibrate Press the MENU button to select bALA Press the ENTER button to confirm the current mode will blink Use the DOWN and UP buttons to select Red Green Blue Once the mode has been selected press the ENTER button to setup Use the DOWN and UP buttons to change the value 125 255 Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu Display Inversion Press the MENU button to select id iSAP Press the ENTER button to change to the mode display normal It will be automatically saved after 8 seconds Press the ENTER button again to select the mode display inversion To go back to the functions press the MENU button Press and hold the MENU button for one second or wait for one minute to go back to the main menu Display normal mode is for floor standing the unit Display inversion mode is for hanging the unit from a ceiling PAn Pan Inversion Press the MENU button to selectPAn Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the S normal or825_ pan inversion mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU b
4. am to address your first 4 units Channel Unit 1 Unit 2 Unit 3 Unit 4 mode Address Address Address Address Qchannets 1 10 19 383 4 3 DMX 512 Configuration value Function channel a fe 2 fe 4 fo Ts fo a Fast close Slow Open 0 010 Stand alone Sound mode 011 255 Sound sensitivity low high 4 4 DMX512 CONNECTION py Y rY Y h hee a A h Ga i d A Bi METS Es 5 240 247 Random Strobe Slow close 190 231 Fast Open 7 ry i a gt TO On DMX Controller nex OUTPUT COMMON DMX DMX INPUT DMX OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 Inthe last unit the DMX has to be terminated with a termination plug Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 2 Connect the units together in a daisy chain with an XLR plug from the output of the unit to the input of the next unit The cable can not be branched or split to a Y cable 3 The DMX output and input connectors are a pass through type to maintain the DMX circuit when one of the units power is disconnected 4 Each lighting unit needs to have an address setup to receive the data sent by the
5. an Q UP buttons to choose the address from 1 255 Once the address has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu gee O z Master Mode or SLiio Press the MENU button to select Sind Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the Lili Slave Mode Slave 1 BL d Slave 2 or i aSk Master mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu E I Show Mode nicl Press the ENTER button and the Press the MENU button to select display will blink Use the DOWN and UP buttons to select the show 1 or 5m show 2 or 25 3 show 3 or 5h 4 show 4 mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu 2E JII Sound Mode Press the MENU button to select Siia Press the ENTER button and the display will blink Use th
6. controller The address number is between 0 512 usually 0 amp 1 are equal to 1 5 The end of the DMX 512 system should be terminated to reduce signal errors 6 3 pin XLR cable wiring configuration 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Following are a few common problems that may occur during operation and some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connection of the power and the main fuse B Not responding to DMX controller 1 DMX LED should be on If not check DMX cables to see if linked correctly 2 If the DMX address is showing but no response to the controller check the address settings and DMX polarity 3 Try another DMX controller C No response to the sound 1 Make sure the unit is not receiving a DMX signal 2 Check the microphone to see if it is good by tapping it The microphone is located on the bottom plate of the unit 6 Fixture Cleaning The cleaning of external optical lenses must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause a greater accumulation of dirt on the unit s optics Clean with a soft cloth using normal glass cleaning fluid or mild soapy water e Always dry the parts carefully e Clean the external optics at least every 20 days
7. e DOWN and UP buttons to select the 29 sound on or arr sound off mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu SEn Sound Sensitivity Press the MENU and use UP and DOWN button to select 929 and select the sound sensitivity between value O and 255 Press the ENTER button for confirmation after value selection To go back to the functions without any changes press the MENU button again Blackout Mode Press the MENU button to select 110 Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the yes blackout or Oc no blackout mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu 1 oi lw Led Display Press the MENU button to select Eo Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the 25 Led display on or Led display off mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MEN
8. the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit as master and select show 1 show 2 show 3 or show 4 from the Show Mode The other units must be set to either Slave 1 normal or Slave 2 2 light show mode A DMX cable between the units for daisy chain is needed 2 light show In slave mode Slave 1 means the unit works normally and Slave 2 means 2 light show In order to create a great light show you can set Slave 2 on the second unit to get contrast movement to each other even if you have two units only 4 2 DMX Controller By using a universal DMX controller to control the units you will need to set a DMX address from 1 to 512 so that the units can receive a DMX Signal Press the MENU button until is showing on the display Press the ENTER button and the display will blink Use the DOWN and UP buttons to change the DMX 512 address Once the address has been selected press the ENTER button to confirm To go back to the functions without any changes press the MENU button again Press and hold the MENU button one second or wait for one minute to go back to the main menu Please refer to the below diagr
9. us operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Do not touch any power cables during operation as the high voltage may cause an electric shock Warning e To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Do not open the unit within five minutes after switching off e The housing and lenses must be replaced if they are visibly damaged Installation The unit should be mounted via its screw holes onto the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Make sure that the structure to which you are attaching the unit to is secure and is able to support a weight of 10 times of the unit s weight Always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture The equipment must be installed by professionals and it must be installed in a place where is out of the reach of people and no one can pass by or under it 2 Features amp Technical Specification Control Sound active auto Master slave and DMX 512 modes DMX Channels 9 channels Electronic dimming 0 100 Electronic strobe with pulse and random effects High output with low power consumption Compact size and low
10. utton again Press and hold the MENU button for one second or wait for one minute to go back to the main menu f 3 1 ti LE Tilt Inversion Press the MENU button to select LE Press the ENTER button and the display will blink Use the DOWN and UP buttons to select the OG normal or tilt inversion mode Once the mode has been selected press the ENTER button to confirm To go back to the functions without any change press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu _ L Auto Test Press the MENU button to select kE Press the ENTER button and the unit will run a self test with its built in programs To go back to the functions without any changes press the MENU button again Press and hold the MENU button for one second or wait for one minute to go back to the main menu M ACL Reset Press the MENU button to select Skk Press the ENTER button and all channels of the unit will return to their standard position 4 How To Control The Unit 1 Master slave built in preprogram function 2 Universal DMX controller There is no need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show pd on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that
Download Pdf Manuals
Related Search