Trident CRB and SPR Manual_CE
Contents
1. ASSEMBLY 1 Insert the Hop Up and inner barrel assembly into the upper receiver 2 that the bolt catch lever is in place then slide the upper receiver back onto the lower receiver 3 Reinstall and secure the front body pin CLEANING AND i WHILE POINTING THE AIRSOFT GUN IN A SAFE DIRECTION REMOVE THE MAGAZINE AND CYCLE THE GEARBOX UNTIL NOTE 885 EXIT THE INNER BARREL PLACE THE AIRSOFT GUN IN SAFE MODE AND DISCONNECT THE BATTERY PRIOR TO ANY CLEANING PROCEDURES 1 Wipe down the external parts of the gun and remove any dirt and debris 2 Disassemble the airsoft gun as described in the Disassembly section and pull out the barrel and Hop Up assembly A 3 Pull back the adjustment wheel B and lift the Hop Up adjustment lever C up 4 Take a lint free cleaning patch D and place it through the looped end of the cleaning rod E WARNING DO NOT ADD OIL TO THE HOP UP BUCKING EXCESSIVE OIL ON THE HOP UP BUCKING MAY NEGATE THE HOP UP DECREASING RANGE AND ACCURACY 13 CLEANING AND 5 Run the cleaning rod through the barrel from back to front in the same direction that BBs travel KEEP TRACK OF THE B2. 20 RPS SPECIAL FEATURES nU Easy spring change Adjustable rotary Hop Up Ambidextrous fire selector KRYTAC TR113 rail system QU MERE licensed by DEFIANCE Integrated FET system NACE mE EE Was KRYTAC battery stock Locking bolt and bolt release _ _ __ __ lt PACKAGE CONTENTS 1 Trident CRB SPR airsoft gun 1 User s manual 1 Magazine 1 Cleaning rod 1 Set of front and rear sights LOADING THE MAGAZINE High Cap 1 Place the hi cap magazine with the trap door A facing upward Open the trap lt 9 door dispense BBs into the well AOS 2 When close the trap door and turn the winding wheel B forward until the clicking changes tone x DO NOT OVER LOAD THE WARNINE MAGAZINE 1 Using a speed loader or other magazine loader insert the nozzle into the opening of the magazine 2 Press down on the loader plunger to load BBs into the magazine 3 Stop once the magazine is full do not force more into the magazine SELECTOR SWITCH SAFE MODE SEMI AUTO MODE FULL AUTO MODE SEMI SAFE 2 When safe mode the While in semi auto In full auto mode the trigger will not engage mode the airsoft gun gun will continuously fire and the airsoft gun will will only fire one shot for as long as the trigger not fire each time the trigger is remains engaged engaged SAF
3. FLASH HIDER KA008 02U SET SCREW KA009 01U OUTER BARREL KA009 03U INNER BARREL 280MM KA018 00U HOP UP CHAMBER ASSEMBLY KA018 10U TENSION SPRING KA019 00U MOTOR KA020 00U REAR SIGHT ASSEMBLY www krytac com Copyright 2014 KRISS USA Subject to change V 01 R 2015 02 10
4. KI2Y TAC TABLE OF CONTENTS Firearm Safety RUES aire a pe iced tal aed 2 Technical Specifications 4 Package COmtents I 6 Loading the 6 Fire SWIIcha L ULU 7 Battery Installation iecit icc e eere 8 Hop p 9 Clearing Jammed BBs iere eere deed 10 M 11 21 12 Cleaning and 13 Operating Under Harsh Conditions 15 Contact Information sas a ae 15 Trouble Shooting Guide 16 Component Diagrams and 115 6 17 SAFETY RULES Please read the entire KRYTAC manual before operating the airsoft gun This manual covers important safety operational and maintenance topics It is important that the user reads and understands the manual in order to safely handle and operate the air soft gun Failure to follow the safety guidelines and or operational instructions in this manual may result in serious personal injury or damage to the airsoft gun Safety Guidelines EYE PROTECTION Always wear eye protection while sh
5. gt KA002 59U 3 a 7 7 KA002 58U gt 002 440 SA Ons 9 lt KA002 07U 68002 94 KA019 00U 17 CRB SPR COMPONENT DIAGRAM KA020 00U KA018 00U A018 07U KA009 03U 280mm KA018 10U KA009 02U KA002 48U KA008 01U lt gt 0 KA002 49U D J 4900 009 010 KA002 60U KA002 56U KA002 KA002 24U 008 020 8 002 510 002 251 005 011 KA005 06U KA005 07U KA005 11U KA005 06U 2 005 070 KA002 62U KA001 00U D KA001 56U KA005 04U 18 COMPONENT DIAGRAM GEARBOX 001 570 6 KA001 31U KA001 32U 90 Qo 1 170 s gt So 001 400 KA001 88U KA001 16U KA001 31A KA001 35U KA001 37U KA001 35U KA001 37U KA001 03A KA001 35U 2 KA001 3sU e S 370 KA001 37U KA001 35U KA001 05A KA001 35U KA001 37U KA001 87U KA001 87U KA001 44U KA001 87U j KA001 87U KA001 85U KA001 55U KA001 86U 42 KA001 86U KA001 86U 422 KA001 86U KA001 86U KA001 56U KA001 86U 19 COMPONENT DIAGRAM GEARBOX 3 KA001 45U KA001 54U KA001 83U KA001 01A KAD01 72U KA001 25U _ A KA001 76U KA001 80U KA001 24U KA001 19U KA001 49U LI KA001 10U KA001 68U KA001 39U KA001 95U KA001 52U _ lt KA001
6. the Trident series AEGs Proper adjustment of the Hop Up will allow the AEGs to fire in a variety of shooting environments to obtain optimal BB trajectory Hop Up Adjustment 1 the charging handle A rearward locking the bolt plate B This will provide access to the Hop Up adjustment dial C 2 Turn the dial up or down an audible click will confirm each adjustment 3 Increasing the number on the dial will increase the amount of Hop Up on the BB Decreasing the number will lower the amount of Hop Up on the BB 4 Once the Hop Up has been set depress the bolt catch release D to return the bolt plate back to its fully seated position SYSTEM Excessive Hop Up Airsoft BB travels in an extreme upward trajectory Decrease the Hop Up Ideal Hop Up Airsoft BB travels in a long horizontal flight path Insufficient Hop Up Airsoft BB travels a short distance in a downward trajectory Increase the Hop Up 2224 C Insufficient CLEARING JAMMED BBS 1 Disassemble the airsoft gun and remove the inner barrel assembly A see 11 for disassembly instruction 2 Lift the Hop up lever B from the inner barrel assembly refer to step 3 of pg13 3 Take the cleaning rod C and insert the unjamming side from the front of the barrel through to the rear to clear out the jammed BB 4 Look through the barrel to ensure that it is cleared 5 Reassemble the airsoft gun see pg12
7. 33U KA001 23U KA001 70U 3 KA001 84U KA001 22U KA001 84U KA001 50U KA001 59U KA001 73U KA001 27A e KA001 81U KA001 82U KA001 08U KA001 82U KA001 82U e X KA001 08U Qa KA001 75U KA001 82U KA001 81U 20 COMPONENT LIST CRB SPR PART NAME KA001 00U GEARBOX SELECTOR TRANSFER CONTACT SELECTOR SELECTOR TRANSFER GEAR M PISTON HEAD GEARBOX SHELL SCREW _ ___ _ __ KA001 86U SHIM 6 GEARBOX SHELL SCREW gt KA001 87U 001 370 BEARING aaa KA001 39U ANTI REVERSE KA001 88U PISTON HEAD SCREW PISTON TOOTH RACK L ANTI DPI NU M E KA001 95U ANTI RELEASE LATCH 44U GEARBOX SHELL RIGHT BUSHING GEARBOX SHELL LEFT KA002 01U UPPER RECEIVER ANTI REVERSE LATCH PIN KA002 02U LOWER RECEIVER TRIGGER KA002 03U GEARBOX PIN DISCONNECT LEVER KA002 05U FRONT RECEIVER PIN SELECTOR GEAR LEFT KA002 06U REAR RECEIVER PIN SELECTOR TRANSFER AXIS KA002 10U CASTLENUT GEAR KA002 17U MAGAZINE RELEASE SPRING LIST SPR KA002 36U BUFFER TUBE SCREW KA002 37U RECEIVER PIN CAP SCREW 2 SCREW KA002 60U CRUSH WASHER KA003 00U STOCK ASSEMBLY KA003 02U BUTTPAD KA005 01U RAIL10 INCH CRB 005 110 RAIL 13 INCH SPR KA008 01U
8. may cause a malfunction and in some cases damage the airsoft gun KEEP THE SAFETY ON Keep the fire selector set to safe until your sights are aligned on target and you are ready to fire SAFETY RULES FAILURE TO FIRE If the airsoft gun fails to fire misfires or malfunctions do not look into down the barrel of the airsoft gun BBs can jam in the chamber and can launch suddenly while under pressure causing serious injury YOUR AIRSOFT PROPERLY Maintaining your airsoft gun as outlined in the manual ensures that your airsoft gun will be safe to shoot and perform to its designed specifications Alterations modifications or adjustments may damage your airsoft gun making it unsafe to shoot and or voiding all warranty claims STORAGE AND TRANSPORT Keep the fire selector on the airsoft gun set to safe with the magazine and battery removed when storing your airsoft gun Always store your airsoft gun in a safe place and out of the reach of children When transporting your airsoft gun make sure that it is in a designated airsoft gun case Never brandish your airsoft gun in public IT IS YOUR RESPONSIBILITY SAFELY STORE AND WARNING TRANSPORT YOUR AIRSOFT GUN ORANGE TIP Any alteration of the coloration or markings required by state and or federal law may be deemed illegal in a court of law All risks and responsibility of any alteration to the product will be assumed by the operators owners and or
9. ARREL SPRING F IT CAN SEPARATE FROM WARNING THE BARREL ASSEMBLY 6 Pull back on the Hop Up adjustment wheel and lower the Hop Up adjustment lever back into position 7 Reinsert the Hop Up barrel assembly into the receiver and reassemble as described in the Assembly section 14 OPERATING UNDER HARSH CONDITIONS When operating under harsh conditions special maintenance may be required to match the climate conditions of a specific operational area Dust and Sand In harsh dusty or sandy environments excessive debris can cause malfunctions and or excessive wear on parts Keep the gun covered and protected while not in use When performing maintenance use lubrication sparingly as it tends to attract dirt and other particles After use in a dusty or sandy area always field strip the gun as outlined in the Disassembly section cleaning all the areas that can be reached with a soft clean lint free cloth Heavy Rain Never submerge or expose your gun to extremely wet environments Exposure to such conditions may cause electrical failure and fluid to build up inside the gearbox Dry completely with a clean lint free cloth and clean inner barrel when necessary CONTACT INFORMATION For additional troubleshooting information or questions regarding KRYTAC customer service Call M F 07 30 16 30 Pacific Standard Time at 1 855 KRISS US 574 7787 Submit a contact form at www krytac com Em
10. ETY It is advised when you are not ready to fire keep the fire selector TIP switch on the airsoft gun in the safe position DO NOT ENGAGE THE TRIGGER WHILE SWITCHING BETWEEN WARNING MODES THE FIRE SELECTOR INSTALLATION ENSURE THAT THE STOCK IS IN THE FULLY COLLAPSED POSITION BEFORE OPENING THE STOCK COVER DO NOT REMOVE THE STOCK WARNING COMPLETELY FROM THE GUN 1 Set the fire selector to safe mode and depress the stock cover release button A on both sides of the stock to lift and remove the cover 2 Connect either nunchuck battery or small LiPo battery to the connector and place the battery into the stock Push the connector plugs B together firmly until they lock into place a Place the small LiPo battery C so that it rests at the rear of the stock b Place the nunchuck style batteries D down either side of the battery tubes found on the sides of the stock 3 Replace the stock cover by first placing the tab E of the cover into the stock and then rocking the stock cover down into position Ensure that the stock cover release buttons snap securely into place WARNING EXCESSIVE PULLING OR TUGGING OF THE BATTERY WIRES WHEN INSERTING OR REMOVING THE BATTERY CAN CAUSE THE FUSE HOUSING TO COME LOOSE OR DAMAGE TO THE GUN SYSTEM advanced KRYTAC rotary Hop Up unit is a standard feature
11. ail us at customerservice krytac com 15 TROUBLE SHOOTING GUIDE TROUBLE SHOOTING GUIDE amp A i WHEN TROUBLESHOOTING FOLLOW THE SAFETY MEASURES DESCRIBED IN THIS MANUAL WARNING SYMPTOMS CAUSE SOLUTIONS Change selector to Semi Auto Full Automatic 2 eee 2 _ _ _ _ _ _ Loose connection Contact customer service for professional care Motor is running but not firing Inspect magazine Check if magazine is properly loaded into the gun Ensure magazine is loaded with ammunition Ensure the hi cap magazine is properly wound Motor or battery is hot after short use Damaged battery Loose connection terminal Inspect and or replace battery Contact customer service for professional care Semi Auto feature not functioning properly Battery voltage or discharge is too high Condition or replace battery Semi Auto feature not working at all Disconnector is not engaged properly Reset the disconnector by setting the selector to safe then to automatic then to semi Firing cycle slowing down Battery is low on power Charge or replace battery High pitch or grinding noise Motor level is not adjusted properly Contact customer service for professional care BB travels upward Hop Up adjusted too high Dial down the Hop Up adjustme
12. for assembly instruction j It is important to remember that all KRYTAC airsoft guns are made with i high quality precision barrels use only new quality airsoft BBs Never NOTE i use recycled or low quality airsoft BBs doing so may cause excessive i jamming In most cases it can severely damage the internal gearbox and or Hop Up and inner barrel 10 DISASSEMBLY Before opening up the receiver remove the magazine and fire the NOTE airsoft gun in a safe direction to ensure that the Hop Up chamber is clear of any BBs 1 Set the AEG to safe mode 2 Remove the stock cover and disconnect the battery 3 Pull the charging handle rearward to lock the bolt plate back 4 Remove ONLY the front from the receiver 5 Slide the upper receiver forward and away from the lower receiver The bolt catch lever B may fall TO off of the lower receiver when separating the receivers Avoid turning or jostling the lower receiver to help prevent loss of the bolt catch lever 2 gt sr DCOCOCOCOCOCD iun DISASSEMBLY 6 Slide the Hop Up and inner barrel assembly C out of the upper receiver Rer Rumu lt COCOCOCDCOCO EEDA gt KRYTAC
13. nt BB travels downward Hop Up adjusted too low Dial up the Hop Up adjustment BB double feeding or rolling out of the barrel Excessive grease or oil in the hopup chamber Hop Up unit is turned off Fire at least 200 rounds to eliminate excessive grease from the chamber Clean Hop Up unit with supplied cleaning rod Turn Hop Up unit on Hop Up unit can t be adjusted Hop Up adjustment arm is not set properly Reset Hop Up adjustment arm See page 13 sect 6 for reassembly Inner barrel is jammed or jamming Hi Cap magazine not feeding Use of recycled or low quality BBs Inner Barrel is contaminated with BBs or debris Magazine has not been wound BBs are lodged inside the magazine Internal obstruction Use only KRYTAC branded or other high quality BBs Clear and or clean inner barrel with supplied cleaning rod See page 10 for clearing jam section and page 14 for cleaning and maintenance section Wind wheel underneath magazine Contact customer service for professional care DIAGRAM SPR L KA002 22A KA003 00U KA002 20U x KA002 43U KA002 55U c D 2 KA002 36U KA002 31A Q 22 002 301 5 KA002 32A KA002 33U KA002 06U S 002270 KA002 03U e 002 171 002 531 KA002 28U KA002 46Ue9 7 KA002 05U KA002 39U 8 G KA002 39U D KA002 29A CI
14. ooting operating and maintaining your airsoft guns FIREARM SAFETY RULES Always assume that the airsoft gun is loaded Never assume the chamber is empty based on memory or from someone else s word An airsoft gun can still fire with the magazine removed KEEP YOUR FINGER OFF THE TRIGGER Remove your finger from the inside of the trigger guard until your sights are aligned on target and you are ready to fire MUZZLE CONTROL Always keep the muzzle of the airsoft gun pointed in a safe direction Never point the airsoft gun towards anything you do not intend to shoot KNOW YOUR TARGET AND ITS SURROUNDINGS SAFETY DISTANCE Take note of objects in front of and beyond your target Airsoft guns can shoot up to and beyond 150 feet and may travel further than intended without an adequate backstop Never shoot an airsoft gun directly at targets such as rocks glass water or other hard surfaces that may ricochet BBs in unpredictable directions SAFETY IS YOUR RESPONSIBILITY WARNING The KRYTAC airsoft gun is designed and manufactured to KRYTAC s high standards It was carefully inspected before it was packaged and shipped from our factory It is the sole responsibility of the user for its safe use and handling This airsoft gun is safe unless handled irresponsibly or misused BEWARE OF BARREL OBSTRUCTIONS Ensure that the barrel of your airsoft gun is free and clear of any obstructions prior to firing the airsoft gun Failure to do so
15. user of the product A THE ORANGE TIP DOES NOT DISTINGUISH YOUR AIRSOFT GUN AS A TOY ALWAYS TREAT YOUR AIRSOFT GUN AS IF IT WARNING IS A REAL FIREARM HAZARDS OF BEING MISTAKEN FOR A REAL FIREARM Due to the nature and design of some airsoft guns they may be mistaken as a real firearm It is strongly advised to operate an airsoft gun in the safety and privacy of your own home or at a legally sanctioned location or game field Police Peace Officers and Law Enforcement Officers are trained to treat objects that resemble a firearm as one In the event that you are approached by a Law Enforcement Official completely comply with their instructions Never point an airsoft gun at a Law Enforcement Official Confrontation with a Law Enforcement Official may result in serious injury or death ALCOHOL MEDICATIONS AND DRUGS Do not handle or operate your airsoft gun while under the influence of alcohol medication or drugs that may impair judgment SPECIFICATIONS TRIDENT CRB CALIBER 6MM MECHBOX i Krytac Trident Mechbox q with 8 mm Bearing gt RATEOFFIRE Ox Ox lt 20 RPS SPECIAL FEATURES VELOCITY 110 MPS 365 FPS with 0 20g BB ENERGY OUTPUT 12 Joules SPECIFICATIONS TRIDENT SPR e CALIBER C VELOCITY 6MM 121 MPS 400 FPS with 0 20g BB ms MECHBOX ENERGY OUTPUT iKrytac Trident Mechbox 148 Joules with 8 mm Bearing RATEOFFIRE
Download Pdf Manuals
Related Search