PT4200 User Manual
Contents
1. and insert the battery in Press downward the battery pack until the release latch locks ro To remove the battery pack push the release R latch upwards and then slide the battery pack away from the radio Notice Do not short circuit the battery terminals or dispose exhausted battery in fire Do not disassemble the battery casing INSTALLING THE ANTENNA Screw the antenna into the connector at the top of the radio by holding the bottom of the antenna and turn it clockwise until secure INSTALLING THE OPTIONAL SPEAKER MICROPHONE Insert the Speaker Microphone plug into the jacks of the versatile connector Note When use the optional Speaker Microphone the radio will not be waterproof INSTALLING REMOVING THE BELT CLIP Match the grooves of the belt clip with those on the rear of the battery Then press the belt clip downwards to lock it in place To remove the belt clip use your nail or a tool to lift the metal spring piece in the belt clip from the topside and then pull the belt clip away from the radio P CAELI n CAEL n CAELI LED Indicator Lights red while transmitting lights green while receiving a signal Flashes red while in low battery power Channel Selector Rotate to select channel 1 16 Power Volume Switch Turn clockwise to switch on the radio Turn counterclockwise till a click is heard to2. operation occurs it exits battery saving mode automatically LOW BATTERY WARNING When the battery power goes below a certain value in transmitting LED flashes red and Low battery warning tone sounds and then the radio stop transmitting You need to recharge or change the battery 9 MONITOR Off When this function is selected no operation is performed Monitor Momentary Press and hold the monitor button to deactivate the signaling temporarily and squelch un mutes Release it to return to normal operation and squelch mutes Kdr7 Urn Monitor Lock Press the monitor button once to deactivate the signaling and squelch un mutes Press it again to return to normal operation and squelch mutes SQ Off When there is no signal received the squelch circuit of the radio will automatically mute the speaker so you will not hear the background noise Press the MONI key to force the squelch un mute e CTCSS DCS CTCSS DCS tones may have been pre programmed on some channels A CTCSS DCS tone is a sub audible tone which allows you to ignore not hear calls from other parties who are using the same channel The dealer can set CTCSS DCS tones on radio channels When you receive a signal that has a tone different from the one set on your radio you will not hear the signal Likewise signals that you transmit will only be received by the parties whose CTCSS DCS tones are the same as yours Note Using a CTCSS DCS channel doesn t m
3. please replace it with a new battery pack Cannot talk to or hear other group members Other voices from non group members are heard on the Channel Communication range is too short e Make sure the antenna is the original one Check if the battery power is in normal Make sure the CTCSS DCS tone is the same as that of your group members Out of the effective communication range Change the CTCSS DCS tone and make sure to changed the tone of all radios in your group Make sure the antenna is well connected state Ask your local dealer to adjust the squelc level n CAEL HM SETTINGS set by the dealer Selected channel Selected channel or currently working channel Model Serial No Priority channel Priority channel or currently working channel 4 Squelch monitor Open TRANSMITTING RECEIVING CHANNEL FREQUENCY FREQUENCY E TESSDES Close 5 Time out timer Open Close 6 Automatic scan Open Close 1 Channels List 2 The way to restart scanning after its pause Time control Carrier wave control 3 The way to revert the working channel 15 16
4. switch off the radio Rotate it to adjust the volume after turning on the radio PTT Push to talk To make a call press and hold the PTT button then speak into the microphone in normal voice Release the PTT button to receive a call Monitor Button Press to disable the SQUELCH and enable the SQUELCH again Channel Annunciation Button Press it in standby state and the channel number will be annunciated If press and hold this button and at the same time switch on the radio again the type of voice annunciation of channel number will be changed Emergency Button Press and hold this button for over 2 seconds to activate warning tone Press it again to exit the emergency alert state Note When warning tone sounds all of the buttons are disabled Microphone Speaker Jacks For connecting external Microphone Speaker E BASIC OPERATION Switch On Switch on the radio by turning the Power Volume switch clockwise till a click is heard then the radio will be in the state of stand by and you will hear a beep if the dealer has set it And then you will hear voice annunciation of the current channel number Adjust Volume Press the monitor button to listen to the background noise and rotate the Power Volume Switch to adjust volume Select Channels Rotate the channel selector to select channels You will hear voice from the speaker while receiving proper signals If voice annunciation of channel numbe
5. KIIS UN KIIS UN INSTRUCTION MANUAL PT4200 FM HANDHELD TRANSCEIVER CEO n CAEL hMIZUN NOTE Arizun INSTRUCTION MANUAL PT4200 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing va brand two way radios produced by Kirisun Electronics Shenzhen Co Ltd We believe v2 two way radio which always incorporates the latest technology can bring great convenience to your life and work we also believe that the quality and function of 4zzzzv e two way radio can meet your demands for reliable communication PRECAUTIONS Please observe the following precautions to prevent fire personal injury and radio damage Do not operate your radio while taking on fuel or being charged Do not expose the radio for a long period to direct sunlight nor place the radio close to heating appliances Do not place the radio in excessively dusty areas humid n CAELI P CAEL areas or on unstable surfaces Do not modify this radio for any reason Refer service to qualified licensed or certificated technicians only Notice to the User e Government laws prohibit radio communication without permission in government districts Illegal operation is subject to punishment by fine and or imprisonment Refer service to the well trained professional technicians only Safety It is important that the user is aware of and understands hazards com
6. NE 4 INSTALLING REMOVING THE BELT CLIP ssss 4 RADIO OVERVIEW iii eee ats tette ttnes 5 BASIC OPERATION tt cista ene edens 6 SCAN EUNGCTION nente ette 7 STARTING SGCAIN tricot cett ciet eerie reste 7 STOPPING SCAN sf AUXILIARY FUNCTIONS ttr 10 TIMESOUT TIMER iint ta nci eed eren reste eite 10 BATTERY SAVING xem et deerit erts 10 LOW BATTERY WARNING renes 10 MONITOR CTCSS DCS VOICE ANNUNCIATION OF CURRENT CHANNEL NUMBER 11 WIREDGEONE oec re a orc tuos 12 EMERGENCY ALERT 5 t tee t ie eene tes 13 TROUBLESHOOTING GUIDE s etree 14 STINGS tone eedem testen een 15 IS EU ll UNPACKING AND CHECKING EQUIPMENT Carefully unpack the radio We recommend that you identify the items listed in the following table before dis carding the packing material If any damage has occurred during shipment please contact the dealer immediately ll SUPPLIED ACCESSORIES ITEM QUANTITY Antenna 1 Hand strap Belt clip Charger Power adapter Li ion battery pack EM EE EX Instruction manual Antenna Power Adapter Belt clip Charger Hand Strap Battery ll PREPARATION CHARGING THE BATTERY PACK A new battery or a battery whose power appears low power indicator displays one bar or no bar needs charging before using 1 Plug the adapter into an AC wall outlet connect the powe
7. ean your calls are private If other parties CTCSS DCS tones are identical with yours they can hear your calls Voice Annunciation of Current Channel Number If voice annunciation of current channel number has been activated when pressing the channel annunciation button in stand by mode the current channel number will be annunciated in the preset language through the loudspeaker If turn on the radio with this button pressed the annunciation language will be changed Repeat turning on the power with this button pressed the type of the annunciation language can be changed in sequence Chinese Male English Male Chinese Female English Female No Annunciation P eg P gl Wired Clone If wire clone function has been activated after entering wire clone mode the radio will not exit the wire clone mode automatically You have to turn on the radio again to enter the user mode The operating procedure is as follows 1 Press MONI key to turn on the radio About two seconds later the red light flashes twice and two beeps sound and then the radio enters the wire clone mode 2 Press PTT button and slave radio that is to be sent with cloning data will be in the Open Prohibition wire clone mode However the wire clone setting on the master radio will not change Press PTT button If the green light flashes twice and one beep sounds it is in the Open state if the red light flashes twice and two beeps sound it is in the Prohibi
8. g scanning the radio will always transmit from the first channel in the scanning list When pressing PTT button during the scanning pause the radio will always transmit from the currently working channel 5 Priority channel The radio will transmit signals from the priority channel in the scan Your local dealer may prohibit this function Only when there are no less than two channels added in the scan list and the scan function has been activated the radio can start scanning STARTING SCAN When switching to channel 16 the radio will begin to scan and pause after receiving signals STOPPING SCAN When switching to channel 1 15 the radio will stop scanning Introduction P list when pressing PTT button 1 Dealer can set the following two ways to restart scanning after its eei pause 6 Priority channel currently working channel When pressing PTT button during scanning the radio will always 1 Time control transmit from the priority channel When pressing PTT button during The radio will restart scanning after pausing for some time while the scanning pause the radio will transmit from the currently working channel Note Currently working channel means the channel in which the radio holds on under the following four conditions 1 After receiving the signals the radio will still stay in the current channel before restarting the scan 2 When receiving signals during scanning the radio will pause
9. mon to the operation of any radios Warning Turn off your radio before entering any area with a potentially explosive atmosphere where the air contains gas dust and smog etc such as while taking on fuel or while parking at a gasoline service station Precautions in Use Please comply with the following attentions to avoid fire bodily injury and damage to the radio The radio is recommended to transmit for 1 minute and MMI Urn P eg E receive for 4 minutes Long time transmitting or continuous working in high power mode will make the rear side of the radio generate heat Please don t disassemble or assemble the radio under any circumstances Please don t expose the radio to direct sunlight for a long time don t place the radio near any heating devices either Please don t put the radio in extremely dusty moist or dabbling places don t place it on any unstable surfaces either If the radio emits smoke or strange odors turn it off and remove the battery from the radio and promptly contact your local authorized Kirisun dealer CONTENTS UNPACKING AND CHECKING EQUIPMENT 1 SUPPLIED ACCESSORIES neret 1 PREPARATION recent rime tates te bach spes i tuen tics 2 CHARGING THE BATTERY PACK ssssseeeneene 2 INSTALLING REMOVING THE BATTERY PACK 3 INSTALLING THE ANTENNA circo cated 4 INSTALLING THE OPTIONAL SPEAKER MICROPHO
10. on the current channel and will keep staying on it for 3 seconds after the signals disappear 3 Radio will stay on the current channel when pressing PTT during scanning 4 When the radio transmitting ends by releasing PTT button within the transmitting pause time preset by the local dealer the radio will stay in the current channel Selected channel The first channel in the scanning list set by the dealer Priority channel The prior channel in the scanning list set by the dealer Only when priority channel has been selected the options of priority channel and priority channel currently working channel in Revert Channel are available ll AUXILIARY FUNCTIONS TIME OUT TIMER Time out timer can prevent the user from continuously talking overlong and prevent the radio body heating due to continuous longtime transmitting If you continuously transmit longer than the time limit preset by the dealer the radio will stop transmitting and warning tone sounds and to stop the warning tone please release the PTT button Pressing the PTT button again will resume transmitting BATTERY SAVING The automatic battery saving function decreases the power consumption when no signal is received and no operation is conducted If the battery saving function is activated 10 seconds after the radio doesn t receive any signals or no operation is being conducted the radio enters battery saving mode When a signal is received or any
11. r adapter with the battery charger and then the indicator lights yellow 2 Place the battery or radio into the charger slot Make sure the battery is well connected with the charger The indicator turns red and then the charger gets in the state of charging automatically Charging time is about 5 hours When battery is fully charged the indicator turns green While in green light state keep the battery remain in the charger for 1 2 hours which will give you the best battery performance And then disconnect the adapter from the AC outlet Notice The battery is not fully charged in the factory and probably the new battery is falsely indicated as full charge Before the initial use please charge the new battery Kirisun KB 58L Li ion battery is supplied x When charge the battery for the first time after purchase or long time storage over 2 months please repeat charging several times to n CAEL resume the battery normal capacity Do not charge the battery again if it has been fully charged or it is not in the low battery warning state otherwise its life will be shortened or it will be damaged Take the battery away from the charger after charging Ifthe battery is charged after all the power has been exhausted the red indicator will light about 1 minute later INSTALLING REMOVING THE BATTERY PACK Match the guides of the battery pack with the corresponding grooves in the bottom of the radio
12. r has been set the radio will annunciate the current channel number I EU t P eg E gl receiving signals The pausing time can be preset from 0 5 to 5 D Make a Call seconds To make a call select the desired channel 2 Carrier wave control S press and hold the PTT button and speak in The radio will pause scanning after receiving signals and will normal voice Please keep your mouth 3 8 cm restart scanning 3 seconds after the signal disappears j away from the microphone 2 The working channel of the radio will respond to the following channels automatically when pressing PTT button during scanning Receive a Call The dealer can select one among the following six ways Release the PTT button to receive a call Select the desired 1 Last called channel adjust the volume to a proper level and then you can When pressing PTT button the radio will transmit from the last receive others voice channel that received a call 2 Last used currently working channel When pressing PTT button during the scanning the radio will transmit from the last channel that received a call When pressing a SCAN FUNCTION PTT button during the scanning pause the radio will transmit from the currently working channel 3 Selected channel When pressing PTT button the radio will transmit from the first channel of the scanning list 4 Selected channel currently working channel When pressing PTT button durin
13. tion state When entering wire clone mode the default setting on the slave cloned radio is wire clone prohibition 3 Press MONI key the red light flashes and cloning begins When cloning is finished red light turns dim Note To activate Open Prohibition Wire Clone mode short circuit the two points of SELF to switch on the current and enter model setting mode the manually adjustment and wire clone functions are activated automatically then to prohibit wire clone function press MONI key You can also open or prohibit the wire clone mode by PC programming software Once the wire clone function is prohibited the radio cannot enter wire clone mode Wire clone prohibition is set as the default when the radio leaves factory EA Emergency Alert Press the emergency button for more than 2 seconds and then the radio enters the state of emergency alert red light flashes and loud warming tone sounds Press the emergency button again to exit the emergency state In emergency state any other keys or buttons are inactive P CAELI ll TROUBLE SHOOTING GUIDE NO PROBLEM SOLUTION The radio cannot be switched on or no display after being switched on Battery power may be insufficient Recharge or replace the battery pack Battery pack may not be installed properly Remove the battery pack and installit again The battery power consumes quickly after charging The battery life is finished
Download Pdf Manuals
Related Search