LAZERTOYZ ESC`s User Manual
Contents
1. startup 1 long 1short governor 1 long 2 short toot toot toot toot rotation 1 long 3 short toot toot toot toot toot default 1 long 4 short 3 Set item value Programmable option You will hear several tones in loop Set the value matching to a tone by moving throttle stick to the top position when you hear the tone then a special tone emits means the value is set and saved Keeping the throttle stick at the top position you will go back to step 2 and you can select other item Disconnect the battery pack will exit the program mode directly Tones Toot Toot toot On 3 Short Battery Type NiMH NiCd Cutoff Mode Cutoff Threshold Low Startup Very Soft Acceleration Motor Rotation Default Setting Reverse Program Example Setting Brake to Brake ON i e option 2 of the programmable item 1 Enter program mode switch onl Select Programmable Items Set Item Value Programmable Trouble Shooting After power on motor does not work no sound is emitted After power on motor does not work such an alert tone emits beep beep beep beep beep beep The motor doesn t run smoothly or stop running while starting up sudden acceleration The motor runs in the opposite direction in condition of The between battery pack connection and ESC is not correct Throttle sticker is not on bottom position or input voltage is abnor2. LAZERTOYZ ESC s User Manual Thanks for purchasing our SKY series Brushless Electronic Speed Controller ESC High power system for RC model can be very dangerous so please read this manual carefully In that we have no control over the use installation application or maintenance of our products no liability shall be assumed nor accepted for any damages losses of costs resulting from the use of the product Any claims arising from the operating failure of malfunctioning etc will be denied We assume no liability for personal injury property damage or consequential damages resulting from our product or our workmanship As far as is legally permitted the obligation for compensation is limited to the invoice amount of the product in question FEATURES All firmware and components are purchased from renowned makers Multiple motor timing choices so compatible with most brushless motor in the market Compatible with fixed wing and helicopter If the position of the throttle stick is inadequate when power on the motor will not start and emit Beep beep continuous warnings Multiple protection features Over heat protection and throttle signal loss protection low voltage cut off protection Throttle range setting and multiple accelerations start up choices Wires Connection Connectors should be soldered carefully to the cables and insulated with heat shrink tube to avoid shortcut SETTINGS Words in Bold Bl
3. ack are default settings 1 Brake ON OFF 2 Battery type NiMH LiPo 3 Low Voltage Cutoff Type Reduce Power Cut off Power Note When ESC is in low voltage or over heat to slowly reduce the motor power state no matter what the throttle sticker position is the power will reduce to a certain value to stabilize the system 4 Cut off Voltage Threshold Low Voltage Protection Threshold Low Medium High 1 For LI xx packs number of cells are automatically calculated This ESC provides 3 setting options for the low voltage protection threshold Low 2 8V Medium 3 0V High 3 2V For example the voltage cutoff options for a 3 cell Li Po pack would be 3 0x3 9V Medium 2 For Ni xx LiFe packs low Medium High cutoff voltages are 0 60 65 of the initial voltage of the battery pack 0 means no protection For example A fully charged 6 cell NiMh pack s voltage is 1 44Vx 6 8 64V when Medium cutoff voltage is set the cutoff voltage is 8 64V x 60 5 18V 5 Motor Timing Low Medium High In most cases low timing works well for all types of motors However the structure for motors are different please try to use different timing for a better effect For higher speed High timing can be set Some motors require different setups therefore we suggest you to follow the manufacturer recommended setup Note Run your motor on the ground first after making any changes to your motor timing 6 Soft Acceleration Startup Mod
4. e Very Soft Soft Acceleration Start Acceleration Start Acceleration mode is suitable for fixed wing Very Soft and Soft Acceleration suitable for Helicopter The initial rom for Very Soft and Soft Acceleration is relatively low even if the throttle stick is moved to the top position instantly the slow will be provided from start to full rom 7 Active RPM Fixed Wing Helicopter Note Attention Rpm On There will be a 8 second delay from start to full rpm After start up if throttle cut off in less than 3 second then the next start will be as Rpm off mode if throttle cut off in more than 3 seconds then the next star will be in Rpm on mode Once the governor Mode is enabled the ESC s Brake and Low Voltage Cutoff Type settings will automatically be reset to No Brake and Reduce Power respectively regardless of what settings they were previously set 8 Motor Rotation Forward Reverse In most cases motor rotation is usually reversed by swapping two motor wires However in cases where the motor cables have been directly soldered the ESC cables motor rotation can be reversed by changing the value of setting on the ESC 9 Restore factory setup defaults Restore Sets the ESC back to factory default settings Throttle range setting 1 Turn on transmitter move throttle stick to top position connect battery pack to ESC and wait for 2 seconds until you hear toot toot emits 2 The tone of toot toot will repeat
5. for 4 times during these times move the throttle stick to bottom position the motor emits special tones means the setting of throttle range is completed After 1 second the system will enter the battery cells confirmation program and emit 123 for system OK tones Note In order to make ESC compatible with your transmitter s throttle range if you use this ESC for the first time or if you change to use other transmitter you must reset the throttle range by following above mentioned steps Program Setting Program the ESC with your transmitter 4 Steps 1 Enter program mode 2 Select programmable item 3 Set item s value Programmable option 4 Exit program mode 1 Enter Program Mode 1 Switch on transmitter movel throttle stick to top position 2 Connet battery pack to ESC and ye wait for 2 seconds 3 Motor emit 4 times of toot toot tone which means progra 9 mode is entered toot toot toot toot toot toot toot toot toot toot toot toot 2 Select programmable item After entering program mode you will hear 9 tones in a loop with the following sequence If you move the throttle stick to bottom and hear one group of special kind of tones the item will be selected brake 1 short 2 short 3 short battery type cutoff mode toot toot toot toot cutoff threshold 4 short motor timing 1 long
6. mal too high or too low Battery s power doesn t discharge well Motor rotation too high Start Up accelerate sets too high Motor timing too low The between ESC and the motor connection need to be changed Favourite Electronics Shenzhen Co Ltd Check the power connection Replace the connectors Check the voltage of battery pack or move the throttle sticker to the right position Change to use bigger discharge power battery Change to use low rotation motor Start up accelerate sets lower Changes to bigger motor timing Swap any two wire connections between ESC and motor Address 2 F Bldg 1 Henghaofeng S amp T Park Phase II E Block Mingzhu Industrial Zone Avenue ransmitter move throttle stick to Now you ll hear 9 tones ina When a Options Motor starts to ring after Mingzhu Shajing Bao an Shengzhen P R China Tel 86 755 61168882 61168885 Fax 86 755 61168887 op position connect battery pack to short Toot toot move thel IESC then loop you hear hear Toot tone emits move which wait till throttle stick to top position then al toot toot toot toot emits throttle stick to bottom to special tone emits which means youl Website www szfvt com enter the Start Mode Imeans the program mode is entered have set the Brake type to the value lof Brake ON Contac Email sales szfvt com
Download Pdf Manuals
Related Search