Home

iril

1. Professional LED Photography Light User Manual Sonnon DL 913 Overview Before using this product you must read the manual and fully understand how to use it and ensure that you can easily handle the operation method and also use it properly Precautions A This product is an electronic device it may be affected by external environmental factors and cause the camera cannot operate or malfunction Nevertheless this possibility is very small A Please do not allow product to strong vibration otherwise it may cause the product failure A When the products is not in use for a long time please turn off the power of device and remove the batteries A The batteries should be installed correctly Reverse polarity may cause batteries to leak corrosive liquids heat or explosion A Please do not store in a high temperature such as a closed car where under direct sunlight the dashboard and other high temperature areas A Please keep the product dry do not touch product in the wet hand Neither put the product into water nor exposed it to the rain Otherwise the product cannot work normally A Do not use the product near the flammable gases otherwise it may cause fire or explosion Due to the product involved the use of batteries please use in strict accordance with the operation of the camera specification Otherwise it may cause fire explosion or even personal injury Items Included Name of Each Part Product Installation
2. light need to synchronous First on the transmitting LED light press and hold Group A button then turn the power on Release the Group A button when the Group A indicator is flashing Second on the receiving LED light press and hold Group B button then turn the power on Release the Group B button when the Group B indicator is flashing The Group B indicator light will turn off when the synchronous is finished If you want to set multi receiving LED lights just repeat the above procedure The transmitting LED light need to restart when finished the synchronous 2 Under the steady mode press Group A sync button to turn it on and light up the light indicator then rotate the adjustment dial now You can adjust the brightness for those lights which were set to Group A sync Press Group A sync button again and to turn it off 3 Under the steady mode press Group B sync button to turn it on and light up the ight indicator then rotate the adjustment dial now You can adjust the brightness for those lights which were set to Group B sync Press Group B sync button again and to turn it off 4 Under the steady mode press Group C sync button to turn it on and light up the ight indicator then rotate the adjustment dial now You can adjust the brightness for those lights which were set to Group C sync Press Group C sync button again and to turn it off 5 When either Group A B or C was light up to join other groups simply pr
3. the same Then tighten the reinforced wheel in counter clockwise direction 3 The Collocation of Camera or Camcorder Installation Align and wedge in the studio light with hot shoe installed and the camera or camcorder hot shoe then fixed the reinforced wheel by clockwise direction The product is installed Turn on the power switch after the device is powered Group A B C light indicators will light up and turn off automatically after 3 seconds This means it works with normal power and enters into the steady mode Its default is under minimum brightness Laced Under the steady mode you can adjust the LED light by rotating the adjustment dial Gockwise to increase brightness and counterclockwise to reduce brightness There are 30 levels of adjustments Using flash mode after entering into the steady mode press the flash setting switch button and light up the light indicator LED light will tum off and enter into the flash mode Under the flash mode the adjustment of brightness is invalid Press the flash setting switch button again and tur off the flash mode can restore the original setting of steady mode If you use the flash function you need a PC cable or Pixel King Pro transmitter to transmit synchronous instruction the PC cable and King Pro transmitter need to be ordered separately _ Steady Synchronous Mode 1 When using the wireless sync mode both transmitting and receiving LED
4. Product Function How to Use Specificatlonistes coziexasntiowne naea a S EEN AE Items Included After opening the packing please check if all the items below are included You can contact our distributor if any item is missing DL 913 Main Body 1PC Barndoor Bracket 1SET Filter 2PCS User Manual Hot Shoe Wheel Barndoor Bracket Filter Hot Shoe Wheel Name of Each Part Lithium Battery Compartment Battery Switch Brightness Adjustment Dial 3 Group A Sync Button Group B Sync Button Group C Sync Button Flash Setting Button Light Indicator SYNC Input to Power On Off DC9V 14V Input AA Battery Com partment NINA OGCOKL B Barndoor Bracket Holes Q LED Light Board Product Installation Barndoor Bracket Installation There are four barndoor bracket holes at each corner of the LED Light Align four male manual screw of the barndoor bracket to the fixed holes of the LED Light and tighten each one in clockwise direction To release in counter clockwise direction You can easily adjust the angle of the barndoor Please pay attention to the order to cover back the barndoor You have to first cover back two longer ones and then covered two short ones Hot Shoe Mounting Align the screw male direction to the female of the studio light tripod Tighten it with clockwise direction Please ensure the direction of the hot shoe and the studio light is
5. ess the group button that you want To close other groups simply press the group button that you want In case of ABC in the same group AB in the same group or AC in the same group the default of brightness adjustment is under the light of Group A If BC are in the same group the default of brightness adjustment is under the light of Group B There are any groups of lights in groups of the same can be adjusted When you adjust the light as shown in Picture the Pictures will change accordingly When you adjust the light as shown in Picture the Pictures will change accordingly When you adjust the light as shown in Picture the Pictures will change accordingly When you adjust the light as shown in Picture the Pictures will change accordingly g Flash Sync Mode 1 Using flash function must have a PC cable or Pixel King Pro transmitter 2 Using LED light as a transmitting trigger both transmitting and receiving LED light need to synchronous Synchronous procedure same as Steady Synchronous Mode Using the PC sync cord to connect transmitting LED light and camera also turn on the LED flash setting button Now when you press the shutter release on the camera the LED light which under the same channel group will be triggered Flash sync setting and steady synchronous setting are the same 3 Using King PRO transmitter to trigger first Also need to synchronous first Then hold down the Group B
6. off 8 Under flash mode if the receiver and transmitter of ABC AB AC or BCturned on simultaneously any group of the same will flash When shown in Picture triggers the pictures will flash accordingly When shown in picture triggers the pictures will flash accordingly When shown in Picture triggers the picture will flash accordingly When shown in picture triggers the picture Specifications System Mode FSK 2 4GHz Digital Radio System Group Group A Group B Group C Color Rendering Index gt 85 Color Temperature 5500K 200K Operation Temperature 20 C 50 C Distance Maximum 100M Antenna Internal Antenna LUX 2000Lm Irradiate Angle 60 LED Light 308 PCS Flash Support SYNC Trigger and King PRO Flash Trigger Power Consumption Max 16 8W under stand by mode Max 25W under flash mode Power Supply AC DC 9V 14V Battery AA X 8 Lithium Battery 7 2V X 2 Product Dimension 225 X 150 X 48mm Thanks for purchasing PIXEL product and reading this instruction manual If you have any questions you can contact your local distributor or visit http www pixelhk com This information of this instruction manual is updated as of 18th November 2013 For information on the use of the combination of product marketed after this date please contact Pixel s dealer for advice Pel PSM118 V10 01
7. sync switch button of the LED light and tum on the power switch until the light indicator of group B keep blinking Release the Group B sync switch button Then hold the C Key of King Pro and tum on the power switch the display will show Coding which means the channel matching is processing After the channel is matched successfully Group B light indicator of LED light will tum off automatically Now you have to restart the King Pro transmitter If channel matching is unsuccessful please repeat the action For King Pro features please refer to King Pro user manual 4 After finished the channel matching press the flash setting switch and light up the light indicator to enter into the flash mode 5 Under the flash mode open the Group A sync and light up the light indicator to provide the flash signal The LED lights which have set as Group A sync will flash To close Group A press the Group A sync switch the light indicator wil turn off 6 Under the flash mode open the Group B sync and light up the light indicator to provide the flash signal The LED lights which have set as Group B sync will flash To close Group B press the Group B sync switch the light indicator will turn off 7 Under the flash mode open the Group C sync and light up the light indicator to provide the flash signal The LED lights which have set as Group C sync will flash To close Group C press the Group C sync switch the light indicator will turn

iril

Contents

Download Pdf Manuals

Related Search

Related Contents