TELTONIKA T-ModemUSB (TMU
Contents
1. Notice the producer does not provide a SIM card among other items of a package which 15 necessary i fir connection to GSM Network You can obtain a SIM card from your local GSM service provider If any of the components is missing please contact your local distributor 2 TECHNICAL SPECIFICATIONS 2 1 Data transferring T ModemUSB supports all bearers of GSM Network Which data channel is used depends on GSM opetatot and data transfer capacitv in the chosen GSM Netwotk e EDGE class 6 341 2 2 e GPRS class 10 4 1 3 2 e HSCSD class 2 e CSD e SMS textual messages 2 2 Mechanical specifications T ModemUSB housing 15 made of plastic One part of the housing covered by rubber that is why is the devise is more stabile on some surfaces The external dimensions and measures of the unit are shown in picture 1 27 Simin a 632mm Pi2. CS TELTONIKA TELTONIKA T ModemUSB TMU 104 User Manual V1 0 Contents IE 3 4 2 5 5 pec E E EEE E E 5 A A 7 Was 8 US E e 8 3 2 Installation Or Modem Control Tool 9 DVS CIS Up Aa in ee 11 3 4 Sending of Short Text Messages SMS 12 SO 14 Le 15 2 INTRODUCTION This document will provide vou with the instructions how to install and use T ModemUSB and its software 1 ModemUSB id a device designed for and aimed at data transmission via GSM Network The design of this modem enables the connection to your PC through USB interface Once the modem is connected to the PC you can get access to the Internet via one of the data transmission channel integrated in the GSM T ModemUSB supports the following data bearers EDGE GPRS CSD HSCSD SMS 1 PACKAGE CONTENTS I ModemUSB is supplied to clients in carton with all contents which needed for connection to PC and normal work 1 Carton 2 1 ModemUSB modem 3 USB A USB connecting cable 4 CD with Users Guide and drivers 5 External GSM antenna just upon special orders
3. is ereen The device is ready to use 8 Status 15 yellow and SIM card inside no PIN code entered blinking of any possibility to connect to the GSM Network Status is yellow The device has successfully connected to y y the Network for data transfer 3 MODEMO SETUP 3 1 Connecting to PC 1 Turn of your PC 2 Insert the SIM card into modem Follow the instructions on the device sticker Make sure the SIM card is pushed inside till it fixes 3 Plug a small connector of the USB cable into the modem 4 Plug another end of the cable to the USB connection of PC 3 2 Installation of T Modem Control Tool 1 Please insert a CD into the CD ROM 2 The installation program should start automatically If it is not the case so find a catalogue Software in CD and start setup exe file The first T Modem dialog box will be opened Welcome to the l Modem Setup Wizard The installer will guide you through the steps required to install T Modem on your computer WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the law zix T Modem Control Tool Select if you want to install tool T Modem Control Tool Recommended Cancel E Newt 4
4. appear stating that there has been performed any Windows Logo testing to the driver select Continue Anyway Upon this selection copy of appropriate files will begin It could take some minutes When copying of driver folders is finished a successful installation message will appear Click Finish The installation is done 9 Windows 2000 OS Hardware Update Wizard Welcome to the Hardware Update Wizard This wizard helps pou install software for Nokia Mobile Phones 12 Data e If your hardware came with an installation CD E or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue lt Back Cancel Picture 2 New device detecting Wizard Using Windows 20004 OS all T Modem Control Tool installation steps are identical with exception of appearance of Digital Signature Not Found dialog box where Xes button should be clicked Digital Signature Not Found Windows available j T Modem Installation Complete T Modem hat been successfully installed Click Close to exit The Microsoft digital signature affirms that software has been tested with Windows and that the software has not been altered since it was tested The software you are about to install does not contain a Microsoft digital signatur
5. that e You have a GSM SIM card with activated data transfer service e T ModemUSB 15 ready to work SIM card is pushed in the device is correctly connected to the PC the drivers are properly installed e Dial up networking is installed on your PC OS e TCP IP protocol is installed on your PC T ModemUSB supports two different types of information data bearers e GPRS EDGE packet data transfer In this case you have to know APN user name and password e CSD HSCSD data transfer You have to know a phone number of a dial up server If GPRS EDGE data transfer is used you have to set up an APN Access Point Name 1 Start Modem Control Tool 2 Select Search For T Modem 3 Select GPRS gt Settings 11 mi 4 Select an appropriate modem and enter APN Getting connected to Internet 1 The dial up connections being set start Modem Control Tool program The program can be started also from the PC desktop while clicking on the shortcut When the shortcut will be clicked T Modem Control Tool dialog box will be opened fl T Modem Control Tool Ioj x File Modem GPRS SMS Help Disconnect search far T Madem COM port Autodetect SIM OF PIN code ENTERED OK wl Network Network OK Disconnected 2 The program should automatically detect a connected modem If this does not happen select Autodetect function in the
6. Press Next button in the opened box third T Modem dialog box will appear T Modem Select Installation Folder C Program FilesT Modemh 5 In the opened dialog box in the field Folder you can indicate a program installation catalogue In the field Install T Modem for your self or for anyone who uses this computer you can determine the Internet users When function Everyone is chosen every user of this PC could have access to the Internet Upon the choice of function Just me only this user will have Internet access Once the setup has been finished press Next button The forth T Modem dialog box will be opened ila T Modem Confirm Installation 6 Press Next button in the opened box If there is any modem connected to the PC a Plug in modem dialog box will be opened stating that is necessary to plug a modem to the PC 7 Plug the modem to the PC and press button A fifth T Modem dialog box and Hardware Update Wizard will appear 8 WindowsXP OS Windows XP OS will automatically detect a new device Nokia Mobile Phones 12 Data Fax and ask to install driver A dialog box shown in Picture 2 will appear Select Install from a list or specific location and push Next button In the next dialog box point to CD folder si Drivers T ModemUSB Windows and click on the Next button Should a dialog box
7. cture 1 An external look and measures of the device 2 3 Electrical and operating specifications Modem is supplied from 5V USB interface The device does not need any external power supply at all The PC to which is the T ModemUSB modem connected must have a USB interface corresponding to USB 1 1 or USB 2 0 standards Notice The USB connection must support high power mode which allows the device to use currency up to 500 mA from the connection Flectrical parameters of the device shown in the Table 1 Table 1 Electrical parameters of the device Parameter Min Typical Max Meas Units Power Supply Voltage 4 5 5V 5 5V V Average Power 360 2000 mA consumption Operating conditions and other parameters are shown in Table 2 Table 2 Operating conditions and the like Parameter Min Typical Max Meas Units Weight ot s _ Recommended operating 15 35 temperature Marginal operating 220 95 temperature 40 1485 2 4 Indication T ModemUSB has 2 LEDs for indication They are located at the top part of the device Due to these indicating LEDs we can determine in which mode is the device Operating are there any shortcuts in its functionality or not The indication status of the modem is given in the Table 3 Table 3 Description of modem status Power is on Power supply is connected Status is green and Modem is powering up blinking Status
8. e Therefore there is no guarantee that this software works correctly with T ModemUSB If you want to search for Microsoft digitally signed software visit the Windows Update Web site at http windowsupdate microsoft com to see if one is Do you want to continue the installation XI i No More Info Eancel lt Back 10 10 new I Modem dialog box will state a successful Modem Control Tool installation process Press Close button A Dial up Settings box will appear Dial up Settings Ta create Dial up Connection enter or leave default parameters and click OK ISP Phone Number User Password Domain Moke iF you do nt wank ta create Dial up Connection click Cancel 11 Enter dial up settings in the dialog box The dial up settings are automatically read from ini file on the CD Should the parameter fields appear empty the user has to fill in them by him self He can obtain the dial up settings by his GSM operator The settings being filled in the button must be clicked 3 3 Setting up an Internet connection In this chapter we will provide you with general information and procedures necessary for setting up an Internet connection in your PC When using Modem Control Tool the Internet connection settings are determined automatically Before you begin make sure
9. ed on the PIN code will be required If the mode Disabled is chosen PIN code has to be entered just once and this will not be required further on while turning the device on query PIN code enabled 7 PIN code disabled Modem Control Tool program is used for changing security settings How to activate PIN code enabled Start I Modem Control Tool Select Search For T Modem Select Modem gt PIN query Select PIN code enabled and click OK How to activate PIN code disabled Start I Modem Control Tool Select Search For T Modem Select Modem gt PIN query Select PIN code disabled and press OK A new dialog bow will appear where a PIN of a SIM card should be entered Enter PIN and press OK If the PIN code is entered correctly a message will appear confirming the cancellation of PIN code checking 14 4 TECHNICAL SUPPORT This sign on the package means that it is necessarv to read a User Manual which is on the CD before vou start using the device This sign on the package means that used electronic and electric equipment should be stored separatelv If you have faced some problems using the device which you are not able to solve by yourself you ate always welcome to address our technical support department by e mail support teltonika_lt We will be very glad to help you 15
10. field port This function being set press Search for T Modem button The program will find a connected modem Click Connect in order to get access to the Internet fl T Modem Control Tool Ioj File Modem GPRS SMS Help Connect Disconnect Search COM port Autodetect Modem on COMS OK SIM card OK PIN code ENTERED OF wl Network Network IK Connected 3 When Connect is clicked the modem will start establishing connection to the Internet 3 4 Sending of Short Text Messages SMS 1 Using T ModemUSB it is possible to send and receive short text messages SMS Before starting using that ModemUSB function it is obligatory to disconnect from the Internet This will be performed while clicking on Disconnect button FZ Bill T Modem Control Tool Ioj File Modem GPRS SMS Help Disconnect Search for T Madem COM port Autodetect WI PIM OK wl Network OK Network OK Disconnected 2 In order to review SMS in the main T Modem Control Tool window click with the left mouse button on SMS Once this has been done a multi choice field will be opened With the left mouse click on the Messages a Messeges dialog box will be opened x Unread Fead Unsent Sent No Sender Date Tent SBOE HSC TIT TIT TITTI TAT TTIE TE TE TIT cp OUND Gn GOOG TITTI dice OI ai
11. se TIT TIT TITTIE ini lai ie icc aici icc ea TITTI TTETTETIUTTETT 1 3067 05 097 05 15 35 53 12 Test Message Storage SIM Refresh Delete Close 3 In this box you can review the received and sent SMS In the field Messege Storage you can choose which memory you want to use either modem or SIM memory These both kinds of memory will be read upon clicking on Refresh button Delete button is used for deleting marked unnecessary SMS When sending SMS select SMS Send In the main T Modem Control Tool dialog box A new Send SMS dialog box will appear sendsM5 es Phone number Tes Symbols left 160 Send Cancel 4 In the opened dialog box in the field Text is where a SMS text should be written Symbols left shows how much symbols rest recipient s phone number is given in the field Phone number Once the SMS text has been entered and the phone number of a recipient given press Send button and your message will be sent 13 3 5 Changing of security settings For SIM security a unique PIN Personal Identification Number is used Before starting using GSM network services it is necessary to enter a PIN code supports two main GSM security modes PIN code enabled PIN code disabled When PIN code enabled mode is chosen each time when the modem is turn
Download Pdf Manuals
Related Search