Home
here - Kalinka Optics
Contents
1. Aiming and shooting at fixed targets Adjust the elevation turret or chose the appropriate chevron with respect to the range to the target and the ballistics of the ammo being fired Assuming there is no cross wind keep the windage turret at the 0 position Aiming and shooting at moving targets While shooting at moving targets it is necessary to aim ahead of the target To determine how far the aiming point has to be taken out you ll need to estimate the speed of the target and the distance to it The faster the target moves and the further the distance to it the further ahead you ll have to aim Have the moving target aligned with horizontal hairs of the reticule as you aiming RETICULE Rangefinder The rangefinder works by placing the target 1 7 m or 5 8 in height between the horizontal and the top reclining lines with the numbers On the reclining line locate the number closest to the point where the target touches the line Multiply that number by 100 this is the distance to the target in meters 1 meter 1 11 yards Windage scale rangefinder Windage scale can be used to make horizontal adjustments or as a rangefinder Shifting the aiming point by one division left or right will move the point of impact by 10cm 4 for every 100m 333 ft of the distance The distance to the target can be determined by assuming that a 1m 3 4 wide long object fits between the small divisions at 100 m 333 ft Aiming chevron
2. KE IT APART FOR ANY REASON VIOLATION WILL VOID THE WARRANTY WARRANTY The scope meets or exceeds the quality standards set forth by the manufacturer and its technical specifications match those listed in this manual The scope carries 12 months limited warranty against manufacturing defects from the date of sale The retailer can not store the scopes for more then 3 years from the date of the manufacture The scopes can still be sold after the expiration of the 3 year storing limit after receiving an approval from the manufacturer If the scope fails during the warranty period the customer is entitled to have the scope repaired of fixed at the desecration of the dealer of the manufacturer Each party is responsible for shipping cost of the scope at their end The scope must be shipped to Kalinka Optics as outlined by their Warrant amp Return policy which is available for viewing on the website www kalinkaoptics com The package must contain the detailed description of the problem and the clearly written return address If the date of sale can not be determined the warranty period assumed to begin at the date of manufacture of the scope If maintenance or feasible and justifiable repairs have to be done upon expiration of the warranty period all costs related to these services is responsibility of the customer
3. Kalinka Optics Warehouse User Manual www kalinkaoptics com PO 4x32 PO 4x32L PO 8x56 PO 8x56L amp PO 8x56LF Pilade Rifle scopes SPECIFICATIONS Objective Aperture oo o e Dual Diopiter 3 3 and Fine Dual Diopiter 3 3 and Fine Yes Yes Y German Picket or Dragunov German Picket or Dragunov 3V 2 x625A 3V 2x 625A 50 to 400C 50 to 40 C a Fine on LF models only Batteries are necessary for illuminated reticles only INCLUDED EQUIPMENT STANDARD ACCESSORIES Scope 1 Eyepiece and Objective covers 2 Russian Manual 1 Packaging 1 Sun Shade 1 OPTIONAL ACCESSORIES Shade Rubber eyepiece Mounting rings or adapters English Manual INTRODUCTION e Rifle scopes P 4x32 P 4x32L P 8x56 P8x56L amp PO 8x56LF further the scope are designed to assist in aiming at distant targets and can be mounted onto any hunting or assault rifle regardless of caliber Models designated with an L have an illuminated reticule for target acquisition in low light conditions e The scope can be mounted onto weapon using 1 mounting rings or adapters designated to accept scopes with a 1 tube PILADE scopes allow for more precise long distance shooting as they are parallax free contrary to comparable scopes e All reticules available in PILADE scopes have a range finding capability Rangefinding instructions for metered reticles such as the Dragunov are incl
4. ch click varies by the type of the scope Please see the table below One numbered point interval equals 1 MOA or 3 6 at 100 yards Scope Click Value Pilade P 4x32 P 4x32L _ MOA 1 2 100 yards Pilade P 8x56 P 8x56L F 14 MOA 0 9 100 yards To set aiming angles correctly during the sighting process you ll need to know the ballistics of your ammo or determine it by experimentation OPERATION Mounting the Scope The scope can be mounted on the gun using 1 mounting rings or adapters that accept scopes with 1 tube You should determine which rings or adapter is required to mount the scope on your gun as all guns have specific mounting options Keep in mind that accuracy of your scope depends on how well the scope is bore sighted on your gun and the quality of the mount being used Choose the mounting option that will hold the scope securely and won t be compromised by recoil Sighting and Zeroing the Scope IMPORTANT Before mount firing the scope remove the windage and the elevation turret covers Tightly secure the gun at the firing station using sand bags or special sighting rack to avoid shooter related inaccuracy After the trial shots 4 5 have been made adjust the reticule position using the windage and the elevation turrets to reflect the average striking point One or two shots may deviate from the shot group this is normal disregard those shots and make adjustments based on the concentrated group of shots After th
5. ch it to the rifle Rotate the knobs to set the range dial on 1 the windage deflection dial at 0 Perform the test firing with the aid of the optical sight the conditions being the same as for test firing of the rifle with the aid of the open sight but the check point in this case is marked at a height of 14cm from the point of aim If as a result of the test firing all four hits are arranged in a circle 8 cm in diameter but the mean point of impact deviates from the check point by more than 3 cm determine the deviation of the MPI and rotate the dials for range and windage appropriately to bring the shots on target Now if you are like me then you didn t understand how to adjust the sight and all of that MPI stuff was confusing These pictures should help The windage scale can be used to make windage adjustments Shifting the aiming point division will move the striking point by 1 every 100 m 333 feet of the distance The distance to a target of a can be Getermined assuming that a 1 m 3 foot 4 inch wide long object fits the small Givisions at 100 meters 1 pee eag o ce po ni p amame 10 10 tee e 2 The chevrons are designed to adjust for 18 yas bullet drop of ANY caliber You must know Sean the ballistics of your ammo or calculate ew the distance for a one chevron drop first y If the top chevron is zeroed at 100 yds 17 eB Groet tight beteen the horkontal aiming with the 2nd 3rd orth chevrons and the top r
6. diameter e Ifthe shot group does not meet the requirements test firing is repeated If the shot group is found normal determine the MPI and its position relative to the check point Determination of the mean point of impact is shown in Fig 1 The rifle fire accuracy is considered normal if the mean point of impact coincides with the check point or deviates from it in any direction by no more than 5 cm e If during test firing the MPI deviates by more than 5 cm from the CP in any direction the position of the front sight as to its height or that of its body as to side position should be changed accordingly If the mean point of impact is below the check point the front sight should be screwed in if it is above the check point the front sight should be screwed out If the MPI is to the left of the CP the front sight body should be shifted to the left if to the right shift the body to the right The front sight body displacement by mm to the side and one complete revolution of the front sight when screwed in or out will change the position of the mean point of impact by 16 cm when fire is delivered at a range of 100 m CTR CTR 1 2 Fig 1 Determination of mean point of impact MPI 1 by consequent division of lines 2 with symmetrical arrangement of hits CTR means MPI Repeat test firing to make sure that the above displacement of the front sight and its body is properly done e To zero the rifle with the optical sight atta
7. e reticule has been adjusted to deliver reasonable firing accuracy you ll need to set the scale on the elevation and the windage turrets back to the 0 position without actually changing the set windage and elevation settings To do so release the two top screws and very carefully without turning the turrets adjust the scale ONLY by aligning the 0 mark on the scale with fixed mark on the scope Tighten the screws and put the turret covers back on you are done The scope is ready for use While aiming you must put your eye on the optical axis of the scope so the image appears flat and without shadows at the edges Using the soft rubber eyepiece will help you to properly align your eye to the optical axis and ensure the proper eye relief Use the rubber shade for shooting in bright daylight conditions to prevent sunshine directly striking the objective lens and preventing excessive glare ATTENTION The scope has a binocular style diopiter adjustment from 3 to 3 D To adjust the scope to your eyesight release the locking ring by turning it adjust the eyepiece and tightly secure the locking ring The adjustment range for the windage and the elevation turrets may exceed one full turn in either direction resulting in having the scope being set to false 0 In this case the reticule will be significantly shifted off the center and won t represent the actual results of sighting To avoid this refrain from excessively turning the turrets
8. eclining lines On the reclining W drop the aiming point by 1 2 2 5 line locate the number closest to the point and 4 accordingly for each additional where the target touches the line Multiply 100 yds of distance this number by 100 this is your distance to the target in meters 1 m 1 11 yards www kalinkaoptics com The first step is to ensure that the rifle is zeroed with the iron sights Also this process is much easier with little wind effects so do this on a day that isn t windy if possible Set up the rifle on a firm and solid base and aim at a target with the iron sights at a distance of 50 meters Zero the scope at 50 meters or 100 meters by using the scope Set the windage to 0 Now see if the aiming reticle is lined up with the target If it is then your sight is considered an adjusted one If it is not in line then rotate the dials range and or windage as necessary to bring the reticle onto the target At this point if you have to reset your dials so that they show 0 when you are zeroed for a target 50 meters away without changing the position of the aiming reticle If your shot hits here and you can keep the rifle unmoved Bring the reticule up to where the shot hit by the adjustments described in step 2 and 3 Fire again NM and repeat until reticule is zeroed e O Aiming reticule To move the reticle to the shot assuming you can keep the rifle in the same position as you make adjustments otherwise tr
9. ial and error will do the same thing just take more ammo you have to loosen the two screws on the top of each dial Loosen the screw but do not remove them As an example we will walk through the above example We need to move the reticle over to the right since the rifle is hitting to the right Rotate the windage dial clockwise until the reticle is approximately under the bullet hole when looking through the scope make sure the silver part of the dial with the numbers on it does not move I had to hold the range dial with pliers If you have to pick up the rifle to do this or otherwise can t keep it on target you will have to do guess work when moving the reticle This may cause you to overcompensate but several iterations of firing and adjusting should zero the rifle Then rotate the range dial counterclockwise to raise the reticle Once you believe that you are close to where the bullet hit screw the silver screws back in and repeat firing the rifle Repeat this process until the rifle is zeroed SAFEKEEPING Avoid hard strikes to the scope or dropping it After using the scope in wet conditions wipe it with dry soft cloth and leave it to dry out at temperatures not exceeding 112 F To protect the glass surfaces of the scope always use the objective lens and eyepiece cups when the scope is not in use When not in use keep the scope in a dry place at room temperature with humidity not exceeding 80 NEVER ATTEMPT TO FIX THE SCOPE YOURSELF OR TA
10. ngs are covered by caps and need a screwdriver to adjust these scopes have exposed rings for quick adjustment Although the rings are exposed and may be moved you can instantly return to your zero point just by turning the rings so that two red marks line up This scope has a one inch tube It is easily mountable to any weapon that takes Weaver style rings Ruger rings Dovetail rings or other one inch rings The Pilade is a top selling scope and one of our most recommended The scope has three major optical parts Objective lens Inverting lens and the Eyepiece The objective lens projects a de magnified inverted image on the reticule plane The inverting lens system transfers the image and reticule onto the focal plane of the eyepiece and at the same time inverts the image The user sees the directly magnified view of the image and the reticule The scope is parallax free which means that the reticule won t appear to be shifted related to the target once the user changes its position relative to the optical axis of the scope To get sharper image adjust the eyepiece to your eyesight using the diopiter adjustment ring Once set to the desired position the setting can be secured by the locking nut The reticule can be adjusted in any direction as needed during sighting The reticule is adjusted by using windage and elevation turrets Windage and elevation turrets have scaled cams with the aiming angles to assist you during the sighting process The value of ea
11. s The chevrons are designed to adjust for bullet drop of ANY caliber provided you know the ballistics of the ammo If the top chevron is zeroed at 100 yards aiming with 2nd 3rd and the 4th will drop the aiming point by 1 2 2 5 and 4 accordingly for each 100 yards of the distance Zeroing There are a few different ways to zero this sight The reticle is displayed below with an explanation of its features and how to determine range to target e Zeroing with the iron sights first o The rifle is test fired by four shots aiming thoroughly and uniformly with the aid of the open iron sight Fire is conducted at the black rectangle 20 cm wide and 30 cm high secured on a white board m high and 0 5 m wide The point of aim is the middle of the black rectangle bottom edge During firing when the open sight is used the normal position of the MPI is marked with chalk or a colored pencil by the plumb line 16 cm above the point of aim This point serves as the check point CP The range is 100 m Firing is conducted from the in any method that provides adequate support To test fire and zero a rifle use should be made of cartridges with ordinary bullets having a steel core Fire is conducted with the knife bayonet removed Upon firing the shots examine the target and arrangement of hits determine accuracy of fire and position of the MPI The rifle fire accuracy is considered normal if all the four hits are arranged within the circle 8 mm in
12. uded below The German Picket version will accommodate a meter wide target between the three points of the reticle at 100 meters e The 1000 meter Dragunov military reticle has an extremely effective and useful height based rangefinder for dual use with graduated scales for both standing and prone figure estimation It includes extended distance inverted chevrons providing aiming points for 1000 1100 and 1200 meters Since the range calibrations are measured in equal amounts of MOA this reticle can be used effectively with any caliber of weapon e The scope can be used in various climatic conditions in the temperature range from 40C to 50C 50F to 110 F9 GENERAL DESCRIPTION Kalinka Optics Warehouse carries only the finest rifle scopes The Pilade Series is based on Soviet military designs which are extremely rugged and have the very best optical properties The factory is small private and with the very best quality control Like most Russian optics the Pilade is made in the Zeiss tradition and are of the highest quality for military law enforcement and sporting use The scope allows easy and precise aiming without the parallax inherent to mechanical sights The scope has a fixed click scale up ratio 4 0 2 and has angle of sight and side angle adjustment knobs The L series comes with an illuminated reticule that lets you see where you are aiming in the worst light conditions Unlike most scopes where the sighting ri
Download Pdf Manuals
Related Search
Related Contents
Panasonic TH-65LFB70E touch screen monitor Pentair 720 User's Manual Owner`s Manual - Motiv Electric Bikes Electronic Arts 14633197747 Video Games User Manual ZEONTM WINCH - Warn Industries Manual - Eelectron Kramer Electronics 3.5mm, Plenum, 22.9m Videograbador Serie 670 - Bosch Security Systems UV LIGHT TECHNOLOGY Copyright © All rights reserved.
Failed to retrieve file