YSI IQ SensorNet MIQ PS Module User Manual
Contents
1. 6 1 6 1 Ordering amp Technical Support 6 1 6 2 Service Information 6 1 76029 01 01 2012 0 1 List of contents MIQ PS ba76029e01 01 2012 MIQ PS Overview 1 Overview 1 1 Howto use this component operating manual Structure of the IQ SENSOR NET operating manual IQ Sensor Net Operating Manual System Operating Manual Ring Binder IQ Sensor MIQ Module MIQ Terminal Operating Operating Operating Manual Manual Manual Component Operating Manuals Fig 1 1 Structure of the IQ SENSOR NET operating manual The IQ SENSOR NET operating manual has a modular structure like the IQ SENSOR NET system itself It consists of a system operating manual and the operating manuals of all the components used Please file these component operating manuals into the ring binder of the system operating manual ba76029e01 01 2012 1 1 Overview MIQ PS General characteristics Terminal strip 1 2 Features of the MIQ PS The MIQ PS wide range power supply supplies the IQ SENSOR NET with its operational voltage The operational voltage is forwarded to the consumers in the following ways Inthe case of stacked mounting via the IQ SENSOR NET contacts on the front and rear of the modu2. X11 X10 X9 X8 X7 X6 X5 X4 g 2 1 ON 4 8224 28 2 2 E m 100 V 240 VAC m ez 1 o z o z o z MAINS SENSORNET 3 SENSORNET 2 7 SENSORNET 1 ES i pn N L 3 Sy Mel EM Fig 3 2 Connecting the power line ba76029e01 01 2012 3 5 Installation MIQ PS 6 Screw the cable gland pos 1 in Fig 3 2 with the sealing ring pos 2 into the module housing 7 Loosen the coupling ring pos 3 8 Feed the power line through the cable gland into the module housing 9 Connect phases L and N to the terminal strip Make sure that the cable assignment agrees with the specification on the ter minal label under the terminal strip 10 Tighten the coupling ring pos 3 Warning No free wires are allowed to project into the housing Otherwise there is a danger that safe areas could come into contact with dan gerous voltages This could lead to danger when working with the IQ SENSOR NET Always cut off any wires that are not in use as closely as possible to the cable gland 11 Close the module ba76029e01 01 2012 MIQ PS Maintenance and cleaning 4 Maintenance and cleaning 4 1 Maintenance The MIQ PS requires no special maintenance The general mainte nance of IQ SENSOR NET components is described in the IQ SENSOR NET system operating manual 4 2 Cleaning The cleanin
3. this component operating manual together with the system operating manual and all other component operating manuals in the vicinity of the IQ SENSOR NET system The MIQ PS may only be connected to the power supply by a trained electrician Safety instructions in this operating manual are identified by the warning symbol triangle in the left column The signal word e g Caution indicates the level of danger Warning indicates instructions that must be followed precisely in order to prevent serious dangers to persons Caution indicates instructions that must be followed precisely in order to avoid slight injuries or damage to the instrument or the environment Note indicates notes that draw your attention to special features Note indicates cross references to other documents e g operating manu als ba76029e01 01 2012 Safety instructions MIQ PS Function and operational safety Safe operation 2 1 Authorized use The authorized use of the MIQ PS consists of its use as a power supply module in the IQ SENSOR NET The technical specifications given in chapter 5 TECHNICAL DATA must be observed Only operation according to the instructions in this component operating manual is authorized Any other use is considered to be unauthorized Unauthorized use invalidates any claims with regard to the guarantee 2 2 General safety instructions The MIQ PS is constructed and inspected in accordance with the rel
4. ON chapter of the system operating manual Note To achieve optimum heat transfer it is recommended to always place the power supply module at the back of a module stack Note If there are several power supply modules in the IQ SENSOR NET it is helpful if all the power supply modules are connected to a single power supply As a result the system can be easily switched on and off from a single location 76029 01 01 2012 Installation MIQ PS 3 3 Electrical connections General instructions Cable glands All electric cables are fed from below via prepared openings in the enclosure of the MIQ PS Cable glands with different clamping ranges are included with the MIQ PS to provide sealing between the cable and enclosure as well as for strain relief Select the matching cable gland for the respective cable diameter Small clamping range 4 5 to 10 mm This cable gland is suitable for all IQ SENSOR NET sensor cables 2 C gt sealing ring 20 x 15 x 1 mm 1 cable gland M16 amp blind plug Large clamping range 7 to 13 mm This cable gland is required for cable sheaths with an outside diameter of more than 10 mm and is screwed into the enclosure via an extension piece sealing ring 20 x 15 x 1 mm NL ____ extension piece M16 M20 sealing ring 24 x 19 x 2 mm cable gland M20 Note If necessary you can order more large cable glands in a set of 4 pieces gt Mod
5. WE KNOW Q a xylem brand Operating Manual IQ SENSOR NET MIQ PS IQ SENSOR NET wide range power supply module Mains voltage 100 240 VAC ba76029e01 01 2012 MIQ PS i Contact Copyright Note For the most recent version of the manual please visit www ysi com YSI 1725 Brannum Lane Yellow Springs OH 45387 USA Tel 1 937 767 7241 800 765 4974 Email environmental ysi com Internet www ysi com 2012 Xylem Inc ba76029e01 01 2012 MIQ PS List of contents MIQ PS List of contents 1 OvervioW ck x 1 1 1 1 How to use this component operating manual 1 1 1 2 Features ofthe MIQ PS 1 2 2 lt 5 lt 2 1 2 1 Authorized use 0 02020 2 2 2 2 General safety 2 2 3 Installation Sik hee te Ie eleva 3 1 3 1 Scope of delivery 3 1 3 2 Installation in the IQ SENSOR NET 3 1 3 3 Electrical connections General instructions 3 2 3 4 Connecting the power 3 4 4 Maintenance and cleaning 4 1 4 1 4 1 4 1 5 Technical data 5 1 6
6. el EW 1 Order No 480 051 3 2 ba76029e01 01 2012 MIQ PS Installation General installation instructions Observe the following points when attaching connecting wires to the terminal strip Shorten all wires to be used to the length required for the installation Always fit all the ends of the wires with wire end sleeves before connecting them to the terminal strip Any wires that are not used and project into the enclosure must be cut off as closely as possible to the cable gland Screw a small cable gland with sealing ring into each remaining free opening and close it with a blind plug Warning No free wires must be allowed to project into the enclosure Otherwise there is a danger that areas safe to contact could come into contact with dangerous voltages which could result in life threatening electric shock when working with the IQ SENSOR NET Always cut off any wires that are not in use as closely as possible to the cable gland ba76029e01 01 2012 Installation MIQ PS 3 4 Connecting the power supply Warning If the power supply is connected incorrectly it may represent a danger to life from electric shock Pay attention to the following points during installation Materials required Tools Preparing the power line The MIQ PS may only be connected to the power supply by a trained electrician The connection of the MIQ PS to the power supply may only be carried out when
7. evant guidelines and norms for electronic instruments see chapter 5 TECHNICAL DATA It left the factory in a safe and secure technical condition The failure free function and operational safety of the MIQ PS is only guaranteed if the generally applicable safety measures and the special safety instructions in this operating manual are followed during its use The failure free function and operational safety of the MIQ PS is only guaranteed under the environmental conditions that are specified in chapter 5 TECHNICAL DATA If safe operation is no longer possible the MIQ PS must be taken out of operation and secured against inadvertent operation Safe operation is no longer possible if the MIQ PS has been damaged during transport has been stored under adverse conditions for a lengthy period of time is visibly damaged no longer operates as described in this manual If you are in any doubt contact the supplier of your MIQ PS 76029 01 01 2012 MIQ PS Installation e H 3 Installation 3 4 Scope of delivery The scope of delivery of the MIQ PS is listed in the INSTALLATION chapter of the system operating manual 3 2 Installation in the IQ SENSOR NET The IQ SENSOR NET provides a number of options for integrating the MIQ PS mechanically and electrically in the system stacked mounting distributed mounting The individual types of installation are described in detail in the INSTALLATI
8. g of IQ SENSOR NET components is described in the IQ SENSOR NET system operating manual 76029 01 01 2012 4 1 Maintenance and cleaning MIQ PS ba76029e01 01 2012 MIQ PS Technical data 5 Technical data Note General technical data on MIQ modules are given in the TECHNICAL gt DATA chapter of the IQ SENSOR NET system operating manual Electrical data Power supply Nominal voltage 100 240 VAC 10 96 Frequency 50 60 Hz in accordance with IEC 60038 Mains connection 2 pole N and L Line cross section of mains connection Europe 1 5 4 0 mm USA AWG 14 12 Fuse rating on the operator side 16 A maximum Power consumption Approx 25 W Output voltage Max 24 VDC via the IQ SENSOR NET for de tails see chapter TECHNICAL DATA of the IQ SENSOR NET system operating manual Power output Max 18 W Protection class II Overvoltage category II Instrument internal fuses 5 x 20 T 1 6 A with UL approval Manufacturer Littlefuse Type Series 218 Caution If the original fuse needs to be replaced it may only be replaced by a fuse of the same type and manufacturer ba76029e01 01 2012 5 1 Technical data MIQ PS Instrument safety Terminal connections Cable glands Applicable norms IQ SENSOR NET connec tions EN 61010 1 UL3111 1 CAN CSA C22 2 No 1010 1 3 Additional connectable SENSORNET termi nator terminating resistor Terminal type Screw
9. he Support tab ba76029e01 6 1 Contact Information MIQ PS 6 2 76029 01 01 2012 a xylem brand 1725 Brannum Lane Yellow Springs Ohio 45387 USA 1 937 767 7241 800 765 4974 US FAX 937 767 1058 Email environmental ysi com Internet www ysi com
10. it is not carrying any voltage The power supply must fulfill the specifications given on the nameplate and in chapter 5 TECHNICAL DATA When installed in a building a switch or power switch must be provided as a disconnecting device for the MIQ PS The interrupt facility must be installed in the vicinity of the MIQ PS easily accessible by the user and identified as a disconnecting device for the MIQ PS After it has been installed the MIQ PS may only be opened if the mains voltage has been switched off beforehand Wire end sleeves suitable for the power line with suitable crimping tool 1 x cable gland matched to the cable diameter see section 3 3 on page 3 2 Cable stripping knife Wire stripper Phillips screw driver Small screw driver 1 Cut off the cable to the required length 2 Strip the cable insulation for approx 45 mm 3 Bare the wires of phases L and N and fit them with wire end sleeves 4 If present cut off the protective earth conductor wire at the end of the cable sheath ba76029e01 01 2012 MIQ PS Installation ca 45 mm cut protective conducter here Fig 3 1 Prepared power cable Caution The protective earth conductor must not project into the housing Otherwise malfunctions could occur Connecting the power line 5 Open the module
11. le In the case of distributed mounting via the IQ SENSOR NET SNCIQ cable Inthe case of sensors via the SACIQ sensor connecting cable With the standard MIQ module housing the MIQ PS has the same characteristics as all MIQ modules regarding stability leakproofness and weather resistance It also provides the same wide variety of instal lation options stacked mounting canopy mounting tophat rail mounting etc The number of MIQ PS that are required depends on the number of consumers in the system and their power requirement as well as on the overall loss of power in the IQ SENSOR NET cables Instructions for determining the correct number of power modules are given in the INSTALLATION chapter of the system operating manual The MIQ PS has the following electrical connections on the terminal strip inside the housing 1x mains connection two pole 3x SENSORNET connection 76029 01 01 2012 MIQ PS Safety instructions Special user qualifications General safety instructions gt gt Other labels a E 2 Safety instructions This component operating manual contains special instructions that must be followed during the installation of the MIQ PS power supply module Thus it is essential to read this component operating manual before carrying out any work with the system In addition to this manual the SAFETY chapter of the IQ SENSOR NET system operating manual must be followed Always keep
12. type terminal strip accessible by raising the lid Terminal ranges Suitable for cable diameter Caution Solid wires 0 2 4 0 mm AWG 24 12 Flexible wires 0 2 2 5 mm 4 5 10 mm and 7 0 13 mm Only the line cross sections specified under ELECTRICAL DATA Seite 1 can be used for the mains connection 76029 01 01 2012 MIQ PS Contact Information 6 Contact Information 6 1 Ordering amp Technical Support Telephone 800 897 4151 937 767 7241 Monday through Friday 8 00 AM to 5 00 PM ET Fax 937 767 1058 Email environmental ysi com Mail YSI Incorporated 1725 Brannum Lane Yellow Springs OH 45387 USA Internet www ysi com When placing an order please have the following information available YSI account number if available Name and Phone Number Model number or brief description Billing and shipping address Quantity Purchase Order or Credit Card 6 2 Service Information YSI has authorized service centers throughout the United States and Internationally For the nearest service center information please visit www ysi com and click Support or contact YSI Technical Support directly at 800 897 4151 When returning a product for service include the Product Return form with cleaning certification The form must be completely filled out for an YSI Service Center to accept the instrument for service The Product Return form may be downloaded at www ysi com and clicking on t
Download Pdf Manuals
Related Search