801 Artese 01/F920 US
Contents
1. www krups com N gy Qs 13 IMPORTANT SAFEGUARDS When using electrical appliances basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury including the following Read all instructions carefully eDo not touch hot surfaces Use handles or knobs eTo protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid eClose supervision is necessary when any appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner Return appliance to your nearest authorized KRUPS Ser vice Center for examination repair or adjustment see Guarantee of Performance The use of an accessory not evaluated for use with this appliance may cause injuries eDo not use outdoors Do not let cord hang over edge of table or counter or touch hot surfaces Do not place on or near a hot gas or electric burner or in a heated oven To disconnect turn switch to OFF then remove plug from wall outlet eDo not use appliance for other than intende2. Clean around the filter and the seal The seal of the Clean the seal percolation head with a damp is dirty cloth The seal of the Contact an percolation head is approved KRUPS defective service centre Very loud noise o water in the Fill the tank pump coming from the ank Tank incorrectly Press firmly on itted the tank Ground coffee too Use freshly old or dry ground coffee Water does not o water in the Fill the flow properly ank tank Tank badly Press firmly on itted the tank The filter is Clean the filter blocked the and the grid of ground coffee is the percolation 00 fine or head See the compacted paragraph 00 tightly Maintenance and try using a coarser ground coffee Krups 13 Water does not flow properly Grid of the Put the grid to percolation head soak in the is clogged descaling solution See the paragraph Descaling Appliance scaled See the paragraph Descaling Water passes too quickly Ground coffee too coarse Try a finer ground coffee Insufficient quan Use the spoon tity of ground supplied to coffee measure out the coffee Ground coffee not Compact the compacted ground coffee more The espresso has no head crema on the coffee Ground coffee Try using a finer too coarse ground coffee Ground coffee not Compact the compacted gr
3. hot water reset the function selector c to the position O Preparing an espresso Your appliance enables you to prepare an espresso either with ground coffee or with ESE ready to use pods e Fill the water tank and set the switch d to l a Preparing an espresso with ground coffee e Put the filter for one or two cups in the filter holder e Put some ground coffee in the filter firmly pressing down the ground coffee with the back of the spoon 1 measuring spoon 1 cup 3 e Clean the edges of the filter holder e Put the filter holder in place 2 e Place one or two espresso cups under the filter holder As soon as the appliance reaches the correct temperature the indicator light e comes on e Then turn the function selector c to the position LP e When the cups are full reset the function selector c to the position O e Take the filter holder out of the appliance and remove the ground coffee holding the filter in place with the gripper clamp 4 The filter can now be refilled to prepare more espressos b Preparing an espresso with a measure of ESE e Use only ESE type pods The E S E system was designed for making espresso ristretto pressed in Italian for a quantity of coffee between 35 and 50 ml ESE stands for Easy Serving Espresso It is a pre measured pod of coffee which has been selected ground and compacted between two filter papers re
4. that can ruin the taste of your coffee Before first use e Clean the water heating system with one or two tanks of clean water as follows e Remove the lid lift out the tank and fill it with water 1 e Replace the tank positioning it firmly in such a way that the connecting valve situated beneath the tank opens and replace the lid e Plug in the appliance e Set the switch d to I The indicator light d1 will come on e Place one of the filters in the filter holder without any coffee Then fit the assembly onto the percolation head To position the ilter holder correctly point the handle to the left press the filter holder onto the percolation head then turn the handle to he right until it locks click 2 Place as large a container as possible under he filter holder As soon as the appliance reaches the right emperature the temperature control indicator light e will come on Turn the unction selector c to the position LE and allow all the water contained in the tank o run through the machine elf necessary interrupt this operation by urning the function selector c to the position O to empty the container then resume the operation Using the various functions of your espresso 1 ESPRESSO FUNCTION e For best results preheat the accessories filter holder filter and cups by running water directly into the cups see Before first use e When the cups are full of
5. 0 Caldari Rd Concord Ontario LAK 4N8 krups 15
6. ater for a variety of instant foods and beverages Mounting of the steam nozzle h e Move the auto cappuccino accessory I to the exterior of the appliance and unscrew his ring 11 e Mount the steam nozzle h in place of the auto cappuccino accessory l e Screw the ring h3 of the steam nozzle Be careful to the seal e Move the steam nozzle to the interior of the appliance Please note the sliding part h2 of the nozzle must be in the raised position 6 e Fill the water tank and set the switch d to I The indicator light d1 comes on e Turn the function selector c to the position AND e Move the nozzle towards the outside of the appliance As soon as the appliance reaches the appropriate temperature the temperature control indicator light e will come on e Immerse the tip of the nozzle in the liquid to be heated 7 Return the nozzle to the inside and hold the container by its handle or place it on the grid i 7 e Then turn the function selector c to the position Hp until the liquid is hot enough then reset it to the position O and remove the container e For liquids other than water turn the function selector c to the position ll for the cleaning operation in order to prevent the nozzle from becoming blocked place an empty container under the nozzle select the position fy again turn the function selector c to the position O clean the nozzl
7. d use eUse extreme caution when dispensing hot steam SAVE THESE INSTRUCTIONS 6 Krups CAUTION This appliance is for household use only Any servicing other than routine cleaning and user maintenance should be performed by authorized KRUPS service personnel only see Guarantee of Perfor mance eDo not immerse base in water eTo reduce the risk of fire or electric shock do not remove the base of the machine There are no user serviceable parts inside Repairs should be performed by authorized KRUPS service personnel only SPECIAL CORD SET INSTRUCTIONS Regarding your Cord Set A A short power supply cord is provided to reduce risks resulting from entanglement in a longer cord B Longer extension cords are available and may be used if proper care is exercised in their use C If a long extension cord is used 1 the marked electrical rating of the extension cord should meet or exceed the electrical rating of the appliance 2 if the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 the longer cord should be arranged so that it will not drape over the counter top or table top where it can be accessed by small children or readily tripped over D This appliance has a polarized plug one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit into a polarized outlet only one way If the plug does not fit fully in the outlet re
8. e with a damp cloth e For thorough cleaning of the nozzle please refer to the paragraph Maintenance Notes If you wish to make an espresso immediately after steam the appliance must first cool down until it reaches the right temperature for extraction e To do this insert an empty filter holder no coffee in the machine and position a suitable container beneath it Then turn the function selector c to the position LB e Let the water run through until the indicator light e goes out Then turn the function selector c to the position O After this the machine is now ready once more to make an espresso see paragraph espresso function Please note when the appliance is running and also afterwards the nozzle will be very hot Allow time for the appliance to cool down to prevent scalding or burning Maintenance e Unplug the appliance and allow it to cool e Never wash the accessories for your espresso in the dishwasher e Clean the body of the appliance with a damp cloth After use the water tank must be emptied The drip tray j e Each time an espresso is prepared the drip tray fills with water This is perfectly normal To prevent any overflow remove the grid 8 and empty the drip tray regularly elf necessary clean the drip tray and the grid with water and a little non abrasive washing up liquid rinse and dry When replacing return the plastic block situated at the back of t
9. he tray 9 Krups 11 The percolation head the filter holder and the filters These must be cleaned after every use Simply run a damp cloth over the percolation head and clean the other accessories with water and a small quantity of non abrasive liquid cleanser Rinse and dry elf the percolation head becomes heavily encrusted unscrew its grid using a coin clean it and replace tightening it firmly 10 The seal for the percolation head When you are not using your espresso do not leave the filter holder in the appliance in order to prevent wear on the seal e Clean the seal regularly using a damp cloth The steam nozzle h must be cleaned with a damp cloth after every use Please note it may still be very hot For more thorough cleaning the nozzle may be taken off 11 e Unscrew the tip h1 if necessary using a coin before removing the nozzle from the appliance e Unscrew the nozzle from the appliance using the ring h3 Separate the various components and clean them with hot water and a small quantity of non abrasive liquid cleanser Rinse and dry elf need be unblock the tip h1 using a fine needle e Be careful with the seal on the ring h3 when you replace the nozzle The auto cappuccino accessory I After each use we recommend that you rinse the auto cappuccino accessory in the following manner e Turn the selector c to the position fl e Turn the dial 13 to the clea
10. in milk with varying amounts of froth for making a cappuccino a latte or hot chocolate These liquids are drawn in through the flexible tube 14 and heated with the aid of steam before coming out via the outlet nozzle 15 of the auto cappuccino accessory l If the flexible tube 14 is immersed directly in a carton of milk a single cup is enough to prepare a cappuccino or a latte You can adjust the amount of froth of the milk by using the dial 13 of the auto cappuccino accessory I It is best to use fresh skim or low fat milk not boiled and well chilled kept in the refrigerator The container must also be cold for optimal results do not run the container under hot water before frothing the milk We recommend that you clean the auto cappuccino accessory immediately after use 10 krups please refer to the section Cleaning the Machine If you are making a cappuccino or latte you will need at least a 5 oz cup 150 ml Cappuccino is made using 1 3 espresso 1 3 hot steamed milk and 1 3 frothed milk Caf latte is made using 1 2 espresso 1 2 steamed milk and topped with a bit of frothy milk Hot chocolate immerse the flexible tube directly into the carton if the chocolate milk is ready made or heat the milk if you are using powdered chocolate Then simply mix the powder in the heated milk Mounting of the Autocappuccino accessory I e Move the steam nozzle h to the exterior of
11. l be void if malfunction was caused by damage to the product by accident misuse use on frequency or voltage other than marked on the product and or described in the instructions abuse including tampering damage in transit or use for commercial purposes This warranty gives you specific legal rights and you may also have other rights which may vary from state to state GUARANTEE OF PERFORMANCE This fine KRUPS product is manufactured according to a rigid code of quality standards and with minimum care should give years of service However should the need arise for repairs or for replace ment parts within or after the warranty period please call our CONSUMER SERVICE DEPARTMENT USA 800 526 5377 24 hours a day 7 days a week Canada 905 669 0114 Monday Friday 8 00 a m 4 30 p m You will be provided with specific instruction on how to get your product repaired The department will also be able to answer any general product questions you may have Before calling the Consumer Service Department please have the type number of your KRUPS appliance available You must have this information before calling our Consumer Ser vice Department so that we may better answer your questions The type number can be located by looking at the bottom of your appliance This product is Type F920 Any general correspondance can be addressed to USA KRUPS North America Inc P O Box 3900 Peoria IL 61612 Canada KRUPS Service 2
12. ndering it ready to use This system simplifies the preparation of an espresso by avoiding the need to measure and tamp ground coffee making it significantly easier to clean and care for the appliance It is neither intended nor recommended that you make a long larger coffee with these pods We advise that you take care not to damage the ESE pods during handling and storage krups 9 Place the pod in the filter holder fitted with its ESE filter In the case of a pod with a tongue fold down the tongue towards the interior 5 Put the filter holder in place 2 As soon as the appliance reaches the right temperature the indicator light e comes on e Then turn the function selector c to the position LB e Once the recommended quantity of coffee has been reached turn the function selector c to the position O e Remove the filter holder and throw away the used measure holding the filter in place with the gripper clamp 4 2 STEAM FUNCTION The thumping noise which occurs while steam is being produced comes from the intermit tent regulation of the pump and has no effect on the proper working of the appliance Caution during and after use of the machine the metallic parts of the steam nozzle can become extremely hot PREPARING FROTHED AND STEAMED MILK FOR A CAPPUCCINO A LATTE OR HOT CHOCOLATE The steam function together with the Krups auto cappuccino accessory makes it easy to obta
13. ning position ann e Immerse the flexible tube 14 into a glass of water The minimum quantity necessary is 3 5 ounces 100 ml e Place an empty container below the outlet nozzle 15 Once the appliance reaches the correct 12 Krups temperature the temperature control light e will come on e Then turn the selector c to the setting illo e When all the water has run through the auto cappuccino accessory I turn the selector c to the O position e After use remove the flexible tube 14 from the container e Once this operation is completed clean the outlet nozzle 15 with a damp cloth We recommend that you regularly dismantle the auto cappuccino accessory l and clean it with water a little non abrasive dishwashing liquid and a small brush Rinse and dry before reassembling it 13 Be careful to mount the flexible tube 14 the right way engage the straight cut end into the auto cappuccino accessory I Following these maintenance guidelines will keep your appliance in optimal working condition and help you to produce great tasting beverages time after time Descaling It is vital that you descale your espresso machine in order to guarantee its continued operation e Descale your espresso at regular intervals using citric or tartaric acid We do however advise you to use the Krups descaling accessory reference 054 which is available from approved Krups service centres This access
14. ory includes in addition to two doses of descaler a water hardness test strip to evaluate the frequency of descaling for your appliance in normal use The amount of scaling depends on the hardness of the water but also on how often it is used The frequency of descaling indicated by accessory 054 is thus given by way of indication only You must never under any circumstances use classic sulphuric acid or other products containing this acid as there is a risk of damaging the appliance Carefully check the composition of the descaling products you intend to use Then use the following method e Unscrew the grid of the percolation head and clean it 10 eDissolveg 2 tablespoons of descaler or one packet of accessory 054 in half a litre 16 oz of lukewarm water and pour the mixture into the empty water tank e Set the switch d to I The indicator light d1 will come on Once the appliance reaches the appropriate temperature the temperature control indicator light e comes on e Place a container under the percolation head Run through about 1 3 of the mixture setting the function selector c to the position LB e Set the switch d to 0 and wait 10 to 15 minutes to allow the descaler to take effect e Then set the switch d to e With the function selector c in the position LB allow the remainder of the mixture to run into the container placed under the percolation head e Then
15. ound coffee enough more Ground coffee old Use a fresh or too dry ground coffee Insufficient Steam cappuccino See paragraph foam on milk nozzle blocked Maintenance Milk too old Use fresh milk Milk is lukewarm Cool milk in the refrigerator When using Pod badly Position it E S E coffee positioned correctly leaks around See paragraph the filter holder Preparing an espresso with an ESE measure Filter holder not tightened properly Tighten filter holder until it locks click 14 Krups Residual water Ground coffee not Compact the in the ground sufficiently compac ground coffee coffee ted Insufficient Increase the quantity quantity of of ground coffee ground coffee There is water The drip tray Empty it regularly around the is overflowing appliance Accessories You can personalize your appliance by obtaining from your retailer or from an approved KRUPS service center the following accessories Filter cartridge ref 0880 Descaling kit ref 054 Limited One Year Warranty Your KRUPS F920 is covered by the following warranty If within one year from date of purchase this KRUPS product fails to function because of defects in materials or workmanship KRUPS North America will at its option repair or replace the unit without charge provided the owner has a proof of date of purchase This warranty wil
16. pressure e Do not use the appliance when the drip tray and the grid are not in place e Never unplug the appliance by pulling on the cord e Make sure the filter holder is well tightened before starting to make coffee Reset the selector to O before loosening the filter holder e All the appliances made by KRUPS are subjected to strict 100 inspection Practical user tests are performed with a number of appliances taken at random which explains any traces of utilisation Espresso coffee Espresso coffee is richer in flavor and stronger than ordinary coffee It is traditionally drunk from small espresso cups which have been pre heated Hot water and pressure combine to passed through ground coffee in order to obtain this delicious black foamy coffee which has an invigorating effect You can always recognize genuine espresso because of its characteristic flavor and rich delicious foam crema This however requires both high pressure and your favorite espresso coffee which has been well roasted and correctly ground If you are unable to purchase ground espresso coffee use a coffee grinder to grind the beans The coffee must not be ground too fine It should be slightly grainy If it is too fine you run the risk of blocking the grids of the percolation head and the filter To guarantee complete success in making a good espresso it is necessary to use fresh clean cold water free of chlorine or other impurities
17. reset the function selector c to O e Run two tanks of fresh water through to rinse the percolation head To do this fill the tank place a container under the percolation head reset the function selector c to LB and allow the content of the tank to run through then set the function selector c to O and the switch d to O replace the grid on the head of the appliance see paragraph Maintenance 10 Notes In the case of serious scaling soak the grid of the percolation head for 5 minutes in 1 3 of the mixture obtained during the first run through If necessary this operation can also be performed with the steam nozzle e To do this dismantle the nozzle as instructed in the paragraph Maintenance and soak the scaled parts for 5 minutes in 1 3 of the mixture obtained during the first run through Rinse the various parts thoroughly before replacing them Problems likely causes and corrective actions Problems Probable Corrective causes actions Espresso not The accessories Pre heat the hot enough are cold accessories cups filter See the paragraph and filter holder Preparing an espresso The appliance is Wait for the not hot enough indicator light e to come on Leaking coffee around the filter holder The filter holder is not fitted correctly See paragraph Preparing an espresso There is residual coffee on the edge of the filter
18. the appliance and unscrew his ring h3 e Mount the auto cappuccino accessory I in place of the steam nozzle h e Screw the ring 11 of the auto cappuccino accessory Be careful not to dislodge the seal 13 Using the auto cappuccino accessory I e Fill the water container with fresh cold water 1 and put the on off switch d on l position The operating light d1 will come on e Turn the selector c to the setting Al e Immerse the flexible tube 14 in the milk to be heated The tube must touch the bottom of the container 12 e Place a cup one third filled with freshly made espresso 12 under the outlet nozzle 15 e Turn the dial 13 to the setting Cb You will obtain a fine smooth froth e To obtain milk which is less frothy turn the dial 13 to the top of the user scale Once the appliance reaches the correct temperature the temperature control indicator light e comes on e Turn the selector c to the setting lk Hot frothy milk will come out of the outlet nozzle e Once you have obtained the desired quantity of frothy milk turn the selector c to the O setting e After use remove the flexible tube 14 from the container and clean the auto cappuccino accessory see section Cleaning the Machine HEATING WATER FOR TEA FOR EXAMPLE OR THICK LIQUIDS SOUP FOR EXAMPLE The steam function together with the steam nozzle h make it easy to heat w
19. verse the plug If it still does not fit contact a qualified electrician Do not attempt to modify the plug in any way KRUPS 7 Description a Lid b Removable swivelling water tank c Function selector d On Off switch d1 operating indicator light e Temperature control indicator light f Percolation head g Filter holder g1 filter for one cup ground coffee g2 filter for two cups ground coffee g3 filter for ESE measure h Steam nozzle for heating liquids h1 tip h2 sliding part h3 ring for screwing unscrewing i Grid j Drip tray k Measuring spoon I Auto cappuccino accessory 11 screwing ring 12 steam tube 13 dial 14 flexible tube I5 outlet nozzle A e Read the instructions for use carefully before using your appliance for the first time any use which does not conform to these instructions will absolve KRUPS from any liability e Never leave the appliance within the reach of small children The use of this appliance by young children or disabled persons must always be under close supervision e Check that the voltage rating of your appliance matches that of your household electrical wiring system Safety recommendations 8 Krups Any connection error will render the guarantee null and void e Do not allow the power cord to hang down within reach of children e Do not remove the filter holder containing the coffee grounds while water is running through as the appliance is then under
Download Pdf Manuals
Related Search