120V-Spectrum Manual 20110923
Contents
1. 6pcs amp Hardware bag Mounting Screw 2pcs A Spring Washer 2pcs Lock Washer 2pcs Wood Screw 2pcs A Tooth Washer 2pcs amp amp Wire nuts For 120V Only 3pcs Blade Balance Kits lpcs Ch Blade Screw 9 pcs P Paper Washer 9pcs Use metal outlet box suitable for fan support Secure outlet box directly to the building structure using wood Outlet Box gt Mounting __ es Bracket uss 4 Install mounting bracket to Outlet box in ceiling using washers and the mounting screws provided with the outlet Dox screws included Outlet box must support 40 Ibs min Do not use existing mounting bracket replace it with new mounting bracket from box 5 Yoke amp Downrod Assembly Yoke cover Downrod Cotter Pin Downrod Set Screw Cross Pin 2 Insert the cross pin through yoke amp downrod and secure with cotter pin 3 Tighten both downrod set screws to further secure downrod then pull down the yoke cover to cover yoke 1 Feed motor lead wires through yoke cover canopy and downrod and insert downrod into yoke P2 6 Blade Installation Attach blade to decorating cap with screws amp washers provided in hardware bag Make sure that all screws are firmly Screws 3 tightened arc Eels ee 7 Hanging the Fan IR eat nee Mounting Bracket Ball Groove Carefully li2. Owners Manual Spectrum WARNING READ AND SAVE THESE INSTRUCTIONS Follow these instructions carefully and be mindful of all warnings shown throughout READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 1 To ensure the success of the installation be sure to read the instructions and review the diagrams thoroughly before beginning 2 To avoid possible electric shock be sure electricity is turned off at the main power box before wiring All electrical connections must be made in accordance with local codes ordinances and or the National Electric Code If you are unfamiliar with the methods of installing electrical wiring and products secure the services of a qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling members and make the proper installations and connections 3 Make sure that your installation site will not allow rotating fan blades to come in contact with any object Blades should be at least 7 feet from floor when fan is in operation 4 If possible mount ceiling fan on a ceiling joist the joist must be able to support the motion and weight of the moving fan If the fan will be mounted on a ceiling outlet box a 4 x 2 1 8 deep METAL octagon box is required one UL listed as suitable for fan support The box and its supporting members must not be able to twist or w
3. ft fan assembly onto mounting bracket Lift fan assembly onto Rotate fan so that the groove on the ball engages mounting bracket the ridge in the mounting bracket 8 Make Wire Connection Transmitter Code Switches Receiver Code Switches Install remote control receiver into mounting bracket and make wire connection This unit has 16 different code combinations 1 Setting the code on the TRANSMITTER A Remove battery cover B Slide code switches to your choice of ON or OFF position Use a small screwdriver or ball point pen to slide each switch firmly up or down C Install 9V DC battery not included D Install battery cover on transmitter 2 Slide code switches to be the SAME POSITIONS as set on your receiver 9a Make wire connection for 100 127VAC 60Hz2 Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block Note Wires from house may vary in color and may not include ground wire green After wiring is completed gently push wires into junction box with wire nuts pointing upward From House From Remote From Fan White White AC N Motor N Black Black AC L Motor L Blue for light kit Green 2Ss0S30 Green for ground wire from downrod Green from mounting bracket P3 10 Canopy installation 1 Push up the Canopy until the two screws on mounting bracket are engaged wit
4. h Key Holes in canopy 2 Rotate the canopy slightly until the two screw heads Key Holes are in the small end of the Key Holes Canopy 3 Tighten both screws Screw Mounting Bracket Remote Control Receiver Canopy Ridge lt Light kit fixture Gul0 max 35W Attach amp rotate down bulbs GU10 max 35W x1 Attach amp rotate down glass shade not included clock wisely to light kit fixture clock wisely to light kit pan 12 Turn the power on your fan is ready for operation P4
5. ork loose DO NOT USE PLASTIC BOXES Installation on a concrete ceiling should be performed by qualified personnel 5 Blades should be attached after motor housing is hung and in place Fan motor housing should be kept in carton until ready to be installed to protect its finish If you are installing more than one ceiling fan make sure that you do not mix fan blade sets 6 After making electrical connections spliced conductors should be turned upward and pushed carefully up into outlet box The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and the HOT wires on the other side 7 Electrical diagrams are for reference only 8 After fan is completely installed check to make sure that all connections are secure to prevent fan from falling and or causing damage or injury 9 The fan can be made to work immediately after installation the bearings are adequately charged with grease So that under normal conditions further lubrication should not be necessary 10 The fan must be turned off and stopped before reversing fan direction 11 This fan is suitable for indoor location only Pl 1 Unpack and inspect fan carefully to be certain all contents are included Blade 2 Turn off power at breaker box to avoid possible electrical shock Lamp Wall Remote Hardware Bag Glass Shade Wood Screw Wire Nut 2pcs
Download Pdf Manuals
Related Search