APC Category 6 Patch Panel User`s Manual
Contents
1. and prying loose 4 Terminate conductors using punch tool Ensure tool is perpendicular to connecting block 6 After cable termi nation attach the rear cable manag er 7 Secure the cables to the manager bracket using cable ties or hook loop straps not included Warning Failure to keep the tool perpendicular to connecting block during punch down may result in incorrect termination If the device arrived damaged notify the carrier If the device requires service do not return to the dealer Following these steps 1 Consult the troubleshooting section to eliminate common problems 2 If the problem still persists call Customer Service or visit the APC Internet Website www apcc com Note the model number serial number and the date of purchase Be prepared to troubleshoot the problem with an APC Technical Support representative If this is not successful APC will issue a Return Merchandise Authorization RMA number and a shipping address e If the device is under warranty repairs are free If not there is a repair charge 3 Pack the device in its original packaging If the original packaging is not available ask Customer Service about obtaining a new set e Pack device properly to avoid damage in transit Never use Styrofoam beads for packaging Damage sustained in transit is not covered under warrant e Include a letter with your name RMA address copy of the sales receipt description of the trouble your2. day time phone number and a check if necessary 4 Mark the RMA on the outside of the package 5 Return the product by insured prepaid carrier to the address given to you by Customer Service North amp South America Europe Asia Pacific APC APC APC 132 Fairgrounds Road Ballybritt Business Park Level 13 The Denison West Kingston Rhode Island 02892 USA Galway Ireland 10800 702000 65 Berry Street 1 800 800 4APC 1 401 789 5735 353 91 702020 North Sydney NSE 2060 61 2 9955 9366 Internet http www apcc com Local country specific centers go to www ape com support contact for contact information Rev A 09 05 100 14049
3. ket using cable prepa ration tool 2 Follow the color coded label for T568A B wiring schemes starting withthe brown pair white blue white blue on the top left IDC blue blue aga g orange white green white positions and ending orange green green white orange white with the blue pair on green orange brown white brown white brown brown the bottom right posi tion Troubleshooting If the channel connection is failing upon comple tion of the installation perform channel and conti nuity test with appropriate cable tester to localize faulty wire panel or termination connection and replace or repair Specifications CAT6PNL 24 CAT6PNL 48 Connector 1 24 x RJ45 48 x RJ45 Connector 2 24x 110 48 x 110 Size H x W x D 48 7 x 4 5 x 3 2 48 7x9x 3 2 19x 1 7x1 2in 19x 3 5 x 1 2 in Shipping weight 1 2 LBS 2 5 LBS 54 KG 90 KG Operating 0 to 60 C Oto 60 C temperature 32 to 104 F 32 to 104 F Safety cULus cULus and approvals 990 2763 5 Slide termination cap over the cable and snap into place prior testing 3 Center the cable jacket with 110 connecting block as shown Insert all conductor pairs into slots by pressing firmly into position Note Begin at the corner of the panel where the cables enter and work towards the middle Note Cap removal can be accomplished by placing a small flat bladed screw driver in the slots of the cap
4. www apc com APC Category 6 Patch Panel User s Manual Initial Start up To obtain warranty coverage please visit warranty apc com Inspection Inspect the Patch Panel upon receipt Notify the carrier and dealer if there is damage The packing is recyclable save it for reuse or dis pose of it properly Placement Install the Patch Panel in a protected area that is free of excessive dust and has adequate air flow Do not install the Patch Panel where temperature is outside the specified limits Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the warranty Installation Tools Required not provided eats Proper installation and termination practices are necessary to ensure the correct opera tion of the patch panel Reference the Telecommunications Industries Association and Electronic Industries Alliance publication Commercial Building Telecommunications Cabling standard General Requirements document number TIA EIA 568 B 1 2001 to ensure proper installation of wiring 2 Phillips Screwdriver Cable Preperation Tool Note Due to the amount of force required for wire installation it is recommended the Patch Panel be installed on the front or rear rails of an APC NetShelter or any other standard rack during the wiring process 110 Punch Tool 1 Strip back approximately 50mm 2 in of cable jac
Download Pdf Manuals
Related Search