EASYA® - Music Direct
Contents
1. Due to constant technological advances Focal reserves its right to modify specifications without notice Images may not conform exactly to specific product EASYA User manual Setting up the system Connect the speakers to the mains using the cables supplied for your region EU or U S Press the ON switch on the speakers to turn them ON On the amplifier panel situated on the back of the speaker select the left speaker to the left position and the right speaker to the right position Fig A SYNC CHANNEL e MOM Moi LEFT RIGHT LEFT RIGHT Loudspeaker position Right Loudspeaker position Left L SOOS T COO Connect the outlet corresponding to your region to the Hub power supply Fig B Connect the Hub to the mains using the standard power supply do not use any other power supply Plug in the power supply into the circular plug on the Hub identified by the marking 7 5V1 1A Fig C EASYA User manual Hub Connections There are several ways to connect your audio and video devices to the Hub Analogue inputs The Hub has 2 analogue inputs 3 5mm jack and RCA Digital inputs The Hub has 3 digital inputs Coaxial TOSlink and mini USB Each of these inputs can accept sampling frequencies up to 96kHz converted to 44 1kHz by the Hub for transmission to the speakers and a resolut2. When all the buttons are programmed press and hold 3 seconds the up arrow button on Focal remote in direction to the hub to go out of the remote learning mode Note To erase programming on the Infrared remote control press and hold for 10 seconds the up arrow on the remote Focal If no key is pressed for 1 minute then programming mode will become inactive EASYA User manual Where to position your loudspeakers Your Easya speakers have been designed to reproduce as faithfully as possible every kind of music Nonetheless it makes sense to follow some simple rules to optimise their performance and to guarantee good tonal balance and a realistic sound stage The loudspeakers should be positioned symmetrically facing the listening area ideally forming an equilateral triangle with it It is however possible to vary these distances to arrive at the ideal compromise for any particular conditions Fig F The loudspeakers should be positioned at the same height in the same horizontal plane Ideally the tweeter should be positioned at the same height as the listener s ear when listening normally Fig G Do not position your loudspeakers too close to a corner of the room and do not place them too close to a wall If positioned close to a wall or a corner this has the effect of exciting certain resonances within the room and artificially increasing the bass Conversely if the bass level is judged to be insufficient y
3. 25 CAUTION May cause an explosion if battery is incorrectly replaced Replace only with the same or equivalent type EASYA User manual Breaking in your speakers The drivers used in Easya are made up of complex mechanical elements and requires an adaptation period before it delivers the best of its performances It must get adapted to the temperature and humidity conditions of their environment This breaking in period depends upon the encountered conditions and can last several weeks In order to shorten this period we advise you to let your loudspeakers operate for about twenty hours consecutively at medium level playing standard music programs but with a large amount of bass Once the components of the drivers arecompletely stabilized it is possible to enjoy the real performances of your Easya loudspeakers Carton contents e 2 loudspeakers 4 mains power cables EU US e 1 user manual e 1 Hub 1 power supply 4 connectors EU Korea US Canada China Japon UK 1 remote control e 4 decoupling spikes e 4 lock nuts e 4 spike protectors e 4 rubber foot pads Please validate your Focal JMlab guarantee by returning the guarantee form enclosed within 10 days Specifications Aluminium Magnesium alloy inverted dome TNV2 Tweeter the tweeter developed for the Easya speaker range uses Focal exclusive inverted dome technology for optimal energy transfer and limited directivity The dome s Alumi
4. Select an input on the Hub other than the aptX Bluetooth one 2 Press the linked button located on the rear panel of the speaker button for 3 seconds The LED next to the linked button will flash rapidly many times per second 3 Press the linked button at the rear of the Hub for 3 seconds The LED next to the linked button will flash rapidly many times per second Please note 1 The speakers and the Hub are linked when all the LEDs speakers and Hub begin to simultaneously flash slowly 2 Hub can be synchronized with only one loudspeaker at a time When the association between the Hub and the two loudspeakers is lost repeat this procedure for each loudspeaker Auto Standby If there is no audio signal detected from the Hub input for 3 minutes the 2 speakers and the Hub will move to standby mode The Hub LED and speakers will light up in red Once an audio signal is detected on the last input selected the system will be reactivated The Hub will provide the musical signal to the speakers after a few seconds the LEDs on the Hub and speakers will light up in white Cables not included Analogue inputs e Analogue 1 3 5mm male mini jack e Analogue 2 2 x RCA male audio right red left white Digital inputs e Digital 1 Coaxial SPDIF digital Audio RCA male 75 Ohms impedance recommended for 24 bits 96 kHz broadband e Digital 2 Optical Toslink male audio e USB Male Mini USB B EASYA User manual Precaut
5. flashing he Bluetooth or USB inputs are selected Left Arrow for previous track and right arrow for next track These functions allow you to move to the next or previous tracks Play Pause middle button is used to start playback or too old or do not support the AVRCP protocol and do not ton on the Hub the Hub can be linked with Bluetooth When the linked mode is activated the Bluetooth input deactivated once the device is linked or after 30 seconds EASYA User manual Remote learning e Ina process of ultimate simplification of the system each of the functions of the Focal remote can be programme in an infrared remote control of your choice TV ADSL Box CD player or universal through the remote program ming mode The procedure is described below Once your remote will be programmed the keys saved by the use will control the Hub Push and hold 3 seconds the up arrow remote control in button on Focal direction o the Hub To program another button v AL LED flash a couple of times M Displays the remote learning mode ON M Push once the Focal remote button to program in direction to the Hub Y Push once the button you want to program on the infrared remote in direction to the hub Y To validate push a second time the button that you want to program on the infrared remote in direction to the Hub
6. may be more convenient to fit and adjust the spike feet after speaker positioning has been optimised EASYA User manual Specifications Easya Tyne Powered wireless 2 1 2 way bass reflex YP floor standing 5 13cm Polyglass woofer Speakers 5 13cm Polyglass bass midrange 1 25mm AVMg TNV2 inverted dome tweeter Frequency response 3dB 50Hz 28kHz Low freguency point 6dB 43Hz Amplifier power RMS 85W 4 Ohms Mains voltage 100 240V Mains freguency 50 60Hz Dimensions HxWxD 3558 x 69 4 x 9 7 16 905x172x240mm Net Weight 37 48lb 17kg EASYA User manual Hub Type Digital wireless transmitter Transmission type Digital Transmission signal frequency 2 4GHz Kleer compatible Range Around 10m without obstacle Sensitivity OdBm Sampling Rate 44 1kHz Resolution 16 bits Mains voltage 100 240V Mains frequency 50 60Hz stand by mode ONI JU Wireless Inputs Bluetooth aptX Digital Inputs Coax Toslink Analogue Inputs Jack 3 5mm RCA External sound card USB Input Dimensions HxLxP 415 16 x 511 16 x 523 49 x 145 x 144mm Weight 0 88lb 400g Conditions of warranty Please contact your Focal dealer if you encounter any problems The guarantee for France on all Focal products is 2 years non transferable if the produc
7. sound reflecting materials in your room In general terms it is good to aim for the wall behind the loudspeakers being reflective for the sound to develop correctly The wall behind he listening position on the other hand is ideally sound absorbing to avoid rear reflections contaminating the stereo image Furniture can be judiciously placed near the side walls of the room to diffuse sound waves and ensure certain frequency zones particularly in the mid range Turning Off Your Television s Speakers If Easya loudspeakers are installed around your TV then you need to disable the speakers of your TV so that the sound is broadcast only through Easya If you can not find the correct setting to turn off your TV speakers please consult the user guide that was packaged with your TV weg 10 15 7015 0 J 0 ODP AN dt 42 3 10 15 S j NA M HT d1 d2 2 d3 Bass level 6dB O gt OdB O im Zone 2 il KOM Zone 3 E A poe LL 3 EASYA User manual Linking loudspeakers Hub The loudspeakers and the Hub have been linked at Focal prior to carrying out the final test on your system The Hub can only be linked to a maximum of 2 speakers In the event that the link between the Hub and one or two speakers is lost you can re link the Hub with one or two speakers as follows How to link the Hub to one or two Easya speakers 1
8. your electrical installation consult the manufacturer of the product or your electricity provider For equipment requiring a battery or another power source consult the user manual 17 Do not overload power sockets exten sion cables or power strips This could lead to fire or electric shock 18 Never insert objects in the ventilation outlets of the equipment The object may come in contact with components exposed to high voltages or cause short circuiting and lead to fire or electric shock Never spill liquid on the equipment 19 Never try to repair this equipment your self opening the equipment may expose you to high voltages or other risks For all maintenance consult a qualified profes sional 20 In case a replacement part is required make sure the maintenance technician uses parts specified by the manufacturer or which have identical specifications to the original part Non compliant parts may lead to fire or have other risks 21 Following any intervention or repair to the equipment ask the technician to carry out tests to verify the product works safely 22 The equipment must not be mounted to the wall or ceiling unless the manufacturer has intended it to and only depending on antenna cables 23 The ON OFF switch situated at the back of the subwoofer is the power supply cut off device The equipment must always be accessible to the user 24 Do not expose to dripping water or splashing
9. EASYA User manual Manuel d utilisation Q if English page 16 Francais page 28 FOCAL THE SPIRIT OF SOUND READ FIRST IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons Caution to prenvent yhe risk of electric shock do not remove cover or back No user serviceable parts inside Refer ser vicing to qualified service personnel The exclamation point within an equilat eral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the product 1 Read these instructions 2 Keep these instructions 3 Take these warnings into consideration 4 Follow all the instructions 5 Do not use this equipment around water 6 Only clean with a dry cloth 7 Do not cover ventilation outlets Follow manufacturer s instructions when installing the equipment 8 Do not install the equipment near a source of heat a cooker a heating duct or other equipment including amplifiers which gives off heat 9 Respect safety instructions for power cable The power cable has two prongs o
10. ion up to 24 bits sample converted to 16 bits per Hub for transmission to the speakers DSL BOX og Bluetoothi AL OL EASYA User manual Bluetooth wireless technology input In order to link a device with the Hub it must be Bluetooth compatible and the aptX Bluetooth input must be selected on the Hub There are two ways to set the Hub to linked mode e By pressing and holding down the sync button located on the back of the Hub for 3 seconds e By pressing and holding down the Down Arrow remote control button for 3 seconds When the Hub is in Bluetooth linked mode the aptX Bluetooth input LED on the front starts to flash quickly The Hub is identifiable on the linked device as Focal Hub Bluetooth Receiver To complete the link please refer to the manual for your device for linking with the Hub If no device is linked within 30 seconds the Hub will exit linked mode Once a device has been linked with the Hub it will remain in the memory Linking only needs to take place once The Hub can store twenty linked devices If more than twenty devices are linked with the Hub it replaces the oldest device with the most recent one linked Only one device at a time can be linked with the Hub If you want to connect a device ensure that no other devices are already connected It is advisable to increase the volume of the device connected to the Hub a
11. ions for use The TNV2 tweeter uses a relatively flexible Aluminium Magnesium alloy with a shape memory enabling it to withstand the majority of small impacts in the home Nevertheless we recommend leaving the fabric grilles in place to protect the dome If the dome surface is marked this could have an impact on the tweeter Cleaning instructions The only maintenance required for Easya is dusting with a dry cloth If the cabinet becomes marked we recommend simply using a damp cloth Never use solvents detergents alcohol based or corrosive products scrapers or scourers to clean the loudspeaker surface Keep the loudspeakers away from sources of heat Decoupling spikes assembling Easya loudspeakers are intented to be floor mounted only It is important to ensure that the loudspeakers stand firmly on the floor using the spike feet supplied whenever possible If not use the rubber feet or the protective caps for the spikes Fig J K To screw the spike feet or the rubber feet stand the speaker on its top placed on the packing cap taking care not to damage the cabinet or the drive units during handling Before screwing the spikes on the cabinet screw the lock nut onto the spikes Then screw the spikes fully into the threaded inserts of the cabinet If the cabinet rocks when placed on the floor unscrew one or two spikes that do not touch the floor until the cabinet rests firmly without rocking Finally lock the nuts against the cabinet It
12. nd to control the volume using the supplied remote control EASYA User manual Remote Control Functions and use of buttons Fig E ON OFF INPUT SELECT SELECTION DES ENTREES OW PAIRING Ka O th Bluetooth REMOTE LEARNING PROGRAMMATION TELECOMMANDE FOCAL e Power OFF allows you to manually set the Hub to standby mode All LEDs on the front panel are turned off Does not allow auto ON mode the speaker goes straight to standby mode Press again to return to the same status before setting Power Off Only the Power Off button allows you to return to ON mode e Input selection allows you to select different inputs for the Hub on a cyclical basis e Volume Control allows you to reduce increase or mute t he Hub volume In silent mode the input LED selected on the front flashes Press again to disable silent mode When the or button is activated the input LED selected f e Controlling tracks these functions are valid only when t o nly i e it is not a fast forward or rewind function The ause the source Please note certain Smartphones are low this feature to be used kol a e Bluetooth linking by selecting the Bluetooth input bu devices Press and hold down the button for 3 seconds LED starts to flash on the front of the Hub This mode is if no device has been linked ashes on the Hub and when the minimum or maximum volume is reached the LED stops
13. ne of which is larger than the other A grounded cable has two prongs as well as a third which is the grounding prong The largest or third prong is there for your safety If the power cable doesn t it your power socket seek the advice o an electrician and replace the old power socket 0 Make sure the cable cannot be stepped on crushed or pinched Extreme care must be paid to the plug and the connection o the cable to the equipment 1 Only use accessories recommended by the manufacturer 2 Only use handling equipment legs tripods supports or tables recommended by the manufacturer or those sold with the equipment When using a cart take extra care when moving the cart and equipment to avoid injury in case something falls 13 Disconnect the equipment in case of a thunderstorm or if left unused for extended periods of time 14 All maintenance must be carried out by a qualified professional Maintenance is required following any damage caused to the equipment such as deterioration of the power cable or plug spillage of liquid or insertion of objects inside the equipment exposure to rain or humidity poor functioning or physical damage 15 Do not use any accessories which aren t recommended by the manufacturer to avoid any risk 16 This product should only be connected to the type of power supply as indicated on the label on the equipment In case of uncertainty as to the type of power supply of
14. nium Magnesium alloy guarantees outstanding stiffness and damping The mechanical properties of the new suspension a system using Poron an open cell polyurethane microcellular foam provide numerous benefits excellent dimensional stability and no degradation over times The advantages of the use of Poron in this tweeter are obvious in terms of linearity and distortion reduction This leads to a silkier more precise sound with greater harmonic richness Polyglass membrane midrange and bass drivers impregnated paper cones with a fine layer of silica micro balls for a fully dynamic bass impact precise and distortion free BASH amplifier A powerful 85 W RMS BASH amplifier is seamlessly integrated into each loudspeaker Optimized to work with the speakers Digital Wireless Transmitter The Hub is a digital wireless transmitter which transmits the audio to the loudspeakers in a quality of sound that is absolutely identical to that of a CD Retained wireless transmission technology radio frequency is independent to any Wi Fi network making it robust and sturdy Thanks to its numerous inputs the Hub connects Easya or any other compatible wireless device to all audio sources smartphones tablets computers TV and CD players It is also compatible with the Bluetooth aptX tehnology Profiled vent powerful distortion free bass High efficiency acoustic wadding excellent internal damping sustained deeper bass Decoupling spikes included
15. ou could try moving the loudspeakers nearer a wall to re balance the bass level Fig H Optimisation For perfectionists here is the formula for optimal positioning If Ais the distance from the centre of the woofer to the nearest floor or wall B is the distance to the next closest floor or wall and C the greatest distance A lt B lt C the equation B AC defines the ideal loudspeaker position e For example If the centre of the woofer is 50 cm away from the back wall A and 60cm from the floor B then the side wall will ideally be 72cm away C BYA 72cm Fig I Recommendations for use The behaviour of the Easya loudspeakers depends on the acoustics in the listening room on the correct positioning of the loudspeakers within the room and on the position of the listener It is possible to work these elements together o correct or improve a desired effect Stereo perception is imprecise and poorly centred try moving the loudspeakers closer to one another and or have hem facing the listening point Sound is harsh aggressive the acoustic in your listening room probably has too many reverberations Consider using sound softening carpets upholstered furniture wall hangings curtains etc and sound reflecting materials furniture to absorb or diffuse resonance Sound is flat strangled there are too many sound absorbent items in the room the sound is soaked up Look for he best compromise between sound absorbing and
16. t is re sold from the date of purchase In the case of defective equipment the equipment must be shipped at your expense in its original packaging to the dealer who will test the equipment in order to determine the nature of the fault If the product is still under warranty the product will be returned to you or replaced shipping pre paid If the product is not under guarantee you will be given a repair estimate The warranty does not cover damage resulting from improper use or incorrect wiring e g burnt out moving coils etc Outside of France Focal products are covered by a warranty whose conditions are determined locally by the official Focal JMlab dealer in each country in compliance with the laws in force in the respective territory which can be recycled and or re used This symbol indicates that electrical and electronic eguipment must be disposed of separately from normal garbage at the end of its operational lifetime Please dispose Your Focal JMlab product was developed and manufactured with high quality materials and components 00 of this product by bringing it to your local collection point or recycling centre for such eguipment This will help to protect the environment in which we all live FOCAL THE SPIRIT OF SOUND CE Focal JMlab BP 374 108 rue de l Avenir 42353 La Talaudi re cedex France www focal com Tel 33 04 77 43 57 00 Fax 33 04 77 43 57 04 SCAB 130916 3 codo1386
Download Pdf Manuals
Related Search