Sprint Anton v5 190906.indd
Contents
1. duration of test and maximum allowed CO for the test The test will run for the required duration by appliance according to BS7967 Sprint will emit an alarm if 30ppm or 90ppm threshold is exceeded Sprint is programmed with pass fail criteria for this test Refer to British Standard BS7967 for further details on performing room CO safety tests Once test can be complete press mi soft key to finish To stop test at any time press the ESC key Use the soft keys v or x to select Quit test Use the soft keys to log or print the results When printing Room CO safety test results Sprint will also provide data show ing for how long the recommended level of CO was exceeded This is expressed as hh mm gt allowed 6 Gas escape test Note Battery power will be used at a higher rate under this test Select Gas escape from the Test menu Connect the Gas leak probe to the USB connector the light will illuminate on the probe Sprint will display a warning if the probe is not connected Sprint will display sensor stabilising for approximately 30 seconds When the sensor is stable the unit will ask in clean air before zeroing Press v to zero the unit Sprint will display a bar graph on the screen as gas levels are monitored Place the probe in the area of inspection for several seconds before moving it to other locations Sprint will emit continuous clicks like a Geiger counter If higher gas levels are detected the bar2. 2006 fuel type displayed on the screen is Natural gos correct Use the soft keys to log or print the results Press the ON OFF ENTER button to display the three screens available Screen 1 CO CO2 CO CO2 ratio and pressure Screen 2 O2 excess air temperature and efficiency button tele Screen 3 combines both through the screen 1 and screen 2 screens Tip The screen number is displayed here Tip If symbol is displayed flue probe is not in flue or not connected Tip Press the ON OFF ENTER To perform a pressure zero use the soft key marked To end test press the ESC key o ff Note for personal Flue Gas 1 Flue Gas 2 ff Flue Gas 3 safety a carbon 14 44 27 08 Feb 2006 14 44 27 08 Feb 2006 14 44 27 08 Feb 2006 4 Natural gas Wo Natural gas Natural gas monoxide alarm Shom oj 20 9 will activate at c92 He fH 90ppm CO This will Ratio HAH Temp five p deactivate when I CO levels drop Pressure 0 00 Ffficency HH below 45ppm This is to protect the user from potential hazardous exhaust gas levels Pio Screen 1 Screen 2 Screen 3 8 TELEGAN gas monitoring Sprint V2 Performing tests 2 Let by and Tightness test Let by test Before carrying out the test the pressure must be zeroed with the tube con nected to the instrument but not the pressure source Note
3. Sprint will give a 14 44 27 o8 reb 2006 warning if the pressure points are the I wrong way round l 5 There is an option to time this test Sprint Duran 00 00 displays the duration time on the screen We 7 Press the soft key to start test and timer 7iP 6 To stop timed test press the soft key m 7 To restart test press the soft key M4 To re zero the unit press fo Press the ESC key to return to the Press menu screen To perform the Differential Pressure test repeat steps 2 to 7 above eg 0 0 optional timer Press ESC to return to the Test menu 6 TELEGAN gas monitoring Sprint V2 Performing tests 4 Differential temperature test Sprint can perform a differential temperature test with one or two thermocou ple probes To begin test select Diff Temperature from the Test menu Check the units displayed are the correct temperature scale If no probes are con nected Sprint will display Two probe test Connect both probes to the k type connectors See label on back of unit for FLOW and RETURN Place probes in position The screen will display the tem perature of probe 1 and probe 2 and the differential temperature Use the soft keys to log or print the results To end test press the ESC key Single probe test When only a single probe is available Sprint will display an additional icon on the screen to represent the first and second reading 1 Place probe in position to make
4. You won t waste your time contacting Inlec Every request for equipment is logged and carefully considered Listening to our customers helps keep our product range up to date and 5 relevant If you are unhappy about any aspect of our service please let us know so we can put it right subject to availability and conditions E e gt aR aie Nationwide Low Call 6 iSalenire j i Online Age CERT NO GB93 1773 LAB NO 0535 Inlec UK Ellerbeck Way Stokesley Business Park Stokesley N Yorkshire TS9 5JZ United Kingdom
5. as print log g 7 or zero moue ESC MOL to exit menus exit tests and step back through screens ON OFF ENTER switch and Flue gas step through screen TELEGAN n gas monitoring Operation Sprint V2 After your Sprint unit has been switched on and performed an auto zero the display will show the Test menu screen ready for use To display the Main menu press the ESC key To enter a menu item use the soft keys below the and screen icons to scroll the menu list and press the soft key underneath the M screen icon to select Some menus have their own submenu Press the ESC key to exit a menu press ESC twice to return to the Main menu from a submenu The soft keys control the function displayed above them on the screen These will change depending on the test or menu or if the ESC key is pressed The menu structure is shown below Press ESC to go to Main menu Test Menu Flue Gas Pressure Diff CO Room Gas Escape Analysis Menu Temperature Safety Detection Let by Tightness Appliance Pressure Diff Pressure Fuel Options Units of Measurement Pressure Temperature Efficency Analyser Settings Display Contrast Auto off timeout Back light Key click Supervisor settings Set date Edit report Change amp time header password LY Stored Logs l Selecta log Fin
6. graph will increase in readings and the sounder will increase in pitch Press ESC to quit the test j2 TELEGAN gas monitoring Sprint V2 Operation I Operation Before using the Sprint flue gas analyser on any heating appliance installation ensure you are familiar with the working practices defined in the BS7967 which details how to perform certain tests and safety issues to consider Auto zero setting Allow the Sprint unit to auto zero during switch on in clean air before per forming any of the following tests flue gas analysis and room CO safety test Ensure all tubes and probes are connected before switch on and zero outside in clean air Pump Sprint runs the internal pump during purge at switch on and switch off and during some tests A rotating purge icon will appear on the screen 4 when purging The speed and therefore the sound emitted by the pump will vary depending on the test being conducted To save on the battery life Sprint will turn off the pump when it is not required When the pump is running ensure the exit gas exhaust is not blocked and do not breath in the exhaust gases 1 1 Menu and operator button overview Sprint provides a large graphic LCD with blue backlight Navigation and func tions are provided by three soft key buttons which change according to what you are doing Use the soft keys to navigate menus select start and end tests change options and select actions g such
7. measurement T1 f z Temperature 2 Press the soft key icon to take a snapshot 144427 on Feb 2006 reading of T1 Do not remove probe until this Foyt ponm snapshot is taken Ret T2 HHH c 3 Move the probe into position to take second Diff temp HHH reading T2 The screen will display the icon to show temperature reading T2 is being taken The screen will display the snapshot temperature the live probe temperature and the differential temperature Tip these icons will appear when Use the soft keys to log or print the results only one probe is avaialble To end test press the ESC key 5 Room CO safety test Ensure the unit has been zeroed in clean air during switch on before performing this test Note For further details on performing Room CO Safety Tests see Appendix I 1 Select CO Room safety from the Test menu Sprint will display the Appliance menu Select the appliance from the list The appliance will be displayed on the screen during the room CO safety test TELEGAN 11 gas monitoring Performing tests Sprint V2 2 Connect probe if required to the Sprint unit and place at the recommended height Refer to British Standard BS7967 if necessary 3 The pump will switch on in readiness for test NB The sound of the pump operating does not indicate the test has begun Press the gt soft key to start test During the test the screen will display the CO reading peak CO reading
8. telegangas co uk Web site www telegangas co uk Exclusive UK Distributor Anton Industrial Services Ltd Unit 6 Park House 15 23 Greenhill Crescent Watford Business Park Watford Hertfordshire WD18 8PH United Kingdom Tel 44 0 870 428 0075 Fax 44 0 870 428 0076 E mail sales anton group com web www anton group com ee HALMA GROUP Registration COM PA NY No 195583 a world class service every day In every sector 1 You can take advantage of expert advice to ensure you get the best most appropriate and cost effective equipment for the job We supply a wide variety of industries so if there is another way to do the job or save you time and money we ll pass on the benefit of our experience for free If we don t have a particular item rather than hiring you something that won t do the job we would rather direct you to an alternative supplier You will always be provided with full instructions and if you still need help call our technical team on Nationwide Low Call 0333 6000 600 Our aim is to save you time frustration and money For full details check our price match guarantee online 13 With Inlec you ll get the most accurate reliable and well maintained equipment available Prices are regularly reviewed to ensure you always enjoy the best value for money We have made a significant investment in test equipment so we ensure that it s well packed to minimise damage and delay
9. x 168 x 65 mm Function buttons key pad 5 button keypad Weight 440 g 0 971bs Pump Flow fail indication SmartPurge Enclosure Integrated robust protective case Standards BS7927 EN50379 BS7967 Data Logging Reports Up to 200 reports depending on type Probes Standard Efficiency Flue Probe Insertion length 250 mm 9 9 with adjustable depth gauge Maximum temperature 800 C 1472 F Construction Ergonomic pistol grip with stainless steel shaft in built with thermocouple in line water trap filter K type thermocouple Accuracy 1 C or 0 3 of reading whichever is best Protective shaft for thermocouple Hose length 2500 mm 8 2 Gas Leak Sensor Probe Gas Leak Sensor 0 10 000ppm natural gas TELEGAN gas monitoring Specification Sprint V2 Gases Range Display Accuracy Detection Response Recovery Diagnostics Resolution limit time time t90 Oxygen 0 25 0 1 0 2 0 3 viv 50 sec 30sec v Carbon 0 10 000ppm 1ppm lt 20ppm 1ppm 90 sec 60sec Vv monoxide H2 com 3ppm pensated optional gt 20ppm 3 Carbon 0 25 0 1 0 2 vv 0 2 vv 50 sec 30 sec dioxide Calculated CO CO2 0 to 0 9999 0 0001 ratio Other Measurements Measurement Range Temperature 50 to 1100 C 58 to 2012 F selectable C or F Efficiency 0 100 net or gross selectable XSAir 0 100 Draught Pressur
10. ASSED Failure Cases Excessive Levels of CO If the CO level exceeds the CO alarm level then the test is considered to have failed and should be immediately aborted The CO alarm may be triggered at any stage before during and after completion of the test and continues to annunciate until the CO level returns to a safe level The result code is FAILED 3 TELEGAN 7 gas monitoring Appendix Carbon Monoxide Room Safety Tests Sprint V2 NB The alarm should prompt the operator to take appropriate action according to BS7967 and safety procedures The sensors in the instrument should be purged with clean air and allowed to recover Unacceptable Levels of CO A peak duration timer records whenever the CO level exceeds the maximum allowed CO level during the test If the total peak duration time exceeds the max peak duration allowed then the test failed due to unacceptable levels of CO The result code is FAILED 2 Acceptable Levels of CO with no Peak If there is no peak in CO level even though it remains below the maximum allowed CO level then the test is failed The result code is FAILED 1 Operator Pass Fail Cases The following results are considered to be operator determined whether the test passes or fails CO Level Exceeds Max Allowable Level for a Short Duration For some appliances eg cooker a peak exceeding the maximum allowed CO level may be acceptable provided the CO level falls back below this le
11. EUROPE S SELECTION OF TEST amp MEASUREMENT EQUIPMENT FOR HIRE Nationwide Low Call ZZ v2 Multi function flue gas analyser ANTON Tel 44 0 870 428 0075 Fax 44 0 870 428 0076 sales anton group com www anton group com Anton Group Tel 44 0 870 428 0075 V2 2 11 05 S M09999 zzz me TELEGAN gas monitoring Issue 1 Summary of Screen Icons Select pick or action Up item or entry Down item or entry Left field Right field Zero pressure Start Pressure amp CO Room Safety tests BY MVA amp AN Stop Pressure amp CO Room Safety tests Restart Pressure amp CO room tests Yes pass or done No or fail or cancel Purge icon Hold pause readings ES Olxi i Select temp 1 flow Differential Temperature test Select temp 2 return Differential Temperature test Save log Print Send XML report to BlueTooth Serial communications with PC in progress please wait Delete Darker contrast Lighter contrast Restore default contrast Edit value Increment value Decrement value Decrement through character list String edit IR TS I WV A te mo e Increment through character list String edit Safety information Read and understand all instructions in the operation section of this manual befor
12. cccccccccceeeeeeeeeeees 18 AA a ee See ee Be ee SE 18 4 2 Water Ula Dashes dasisatelsdeeseta sanavbhesgatveaseGe E E 18 V Specificato accncauauwmaadnenunnnnaceaiieaian 19 X Accessories and spare parts ccccccceceseeeeeteeeeeteeeeees 21 Vi LOJON in eee rrr perce enter AT E T A 22 VISPA NINO Ee e A A AEE 23 VIII Troubleshooting QUIS corscnsscrelerarcumenenonnaaaunnendaniind 24 Appendix Carbon Monoxide Room Safety Tests 26 Unpacking Sprint V2 Sprint V2 Multi function Flue Gas Analyser Thank you for purchasing the Sprint V2 Multi function Flue Gas Analyser Sprint has redefined flue gas analysis and will give you years of unparalleled service and reliability Please read the instructions carefully before use Keep the manual for future reference Unpacking Important ensure unit is fully charged Remove the Sprint unit from the packaging The Sprint accessories will be located in the carry case Check the contents are complete you should have e Carry case e Sprint unit e Mains battery charger power supply e Rubber boot e Flue probe including water trap e A5 user guide e User manual on CD e Certificate of calibration e 2x1 m tubes for pressure Natural gas or LPG Options to include e Gas leak probe e Additional thermocouple probes e In car charger e Infra red printer Warning Do not attempt to use any other charger power supply with this unit except t
13. ccept M Are you sure to clear logs or press ESC to cancel Switch off Turn off unit in clean air and ensure any gas is purged from sensors Press and hold the ON OFF ENTER button for approximately two seconds The power off screen will be displayed and the pump will run to purge the sensors The pump will run for up to 30 seconds to purge unit if gas is present Sprint will normally switch off in 10 seconds Press the ESC key to cancel the switch off sequence Charging battery Plug the supplied charger into the charger socket The batteries will recharge in six hours from flat You may leave the unit on charge for longer periods e g overnight without damaging the unit A fully charged unit will give up to nine hours of operation A shorter charge time can be applied such as 1 2 hour to allow a more limited length of operation TELEGAN gas monitoring N Performing tests Sprint V2 Performing tests From the Main menu select Test Menu Refer to section III Operation for more details Warning During testing ensure the combined filter and water trap is not blocked or full Failure to do so may result in an error message 1 Flue gas analysis Before performing the flue gas analysis test check the water trap is clean and is upright arrow should point upwards To begin test select Flue gas analysis from the Test menu Sprint will switch on the pump and begin Flue Gas making measurements Check the 14 44 27 08 Feb
14. continue or the soft keys to print or delete the log Recalling logs To recall a log use the ESC key to display the Main menu Logs can be recalled either by viewing and selecting from the log list or by entering the log number The log list displays the log number test title and date Use the soft keys to choose Select a log or Find a log by number When the log has been selected Sprint will display the log on the screen Use the soft key options to Print or delete the log Use the ESC key to exit the log list and Stored logs menu Printing logs Logs can be printed instantly from the test screen or from Stored logs or directly after a log has been recorded and the log is displayed on the screen Press the Print soft key 4 to send the log file to the printer Deleting logs Single logs can be deleted either from the Stored logs menu or directly after a log has been recorded and the log is displayed on the screen From the Stored logs menu choose Select a log or Find a log by number to find the log you wish to delete Delete the log using the ij soft icon All logs can be deleted from the Stored logs menu Scroll and select Delete all logs and press the MI soft key Press the yes key Are you sure to delete all logs or press ESC to cancel Deleting all logs resets next log number to one 22 TELEGAN gas monitoring Sprint V2 Printing VII Printing Ensure your selected printer is switched on with pa
15. d printed on the report and recorded in the log This fail code identi fies the way in which the test failed and can help identify the cause Also when 2 TELEGAN gas monitoring Sprint V2 Appendix Carbon Monoxide Room Safety Tests the test completes a short text message associated to this code is displayed in a pop up prompt dialog screen to explain the reason for failure The result codes and associated prompt dialogue messages are as follows RESULT amp CODE POP UP PROMPT ON SCREEN PASSED None ANY FAILED Warning CO Room Safety test failed FAILED 1 CO levels did not fall or unstable FAILED 2 CO unacceptably high for too long FAILED 3 CO dangerously high FAILED 4 Unacceptable or incomplete Press ESC key to continue Pass Cases Normal Acceptable Peak of CO Normally for a test to pass the CO levels must peak without exceeding the maximum allowed CO level and then fall by at least 0 5 ppm below the peak value before the end of the test Note that it is not necessary for the CO level to reach or be close to zero at the end of the test so long as it remains below the maximum allowed CO level The result code is PASSED Very Low Levels of CO If the CO levels remain below 2 5 ppm ie close to clean air or background noise levels for the duration of the test then the test is considered to have passed The result code is P
16. d a log by number Delete all logs How to display unit serial number identity and software ver sion Press the ESC key from the Main menu 14 TELEGAN gas monitoring Sprint V2 Setting up ll Setting Up 2 1 Configuration Options Fuel Options Sprint displays the current fuel option on the screen To change the fuel option press the ESC key to enter the Main menu and select Fue Options Use the soft keys to scroll and select the desired fuel using v The new fuel option will be displayed on the test screens Fuel options available are natural gas LPG heavy oil light oil coal wood coke Biomass and BAGASSE Units of measurement To change the units of pressure temperature or efficiency press the ESC key to enter the Main menu and select Units of Measurement Use the soft keys to select the submenu and units for Pressure Temperature or Efficiency Temperature units are degrees Celsius C or degrees Fahrenheit F Pressure units are mBar Pa hPa kPa PSI inWWG mmWG inHG and mmHG Efficiency units are Net or Gross Analyser settings The Analyser settings menu allows you to alter the settings for the display auto off timeout back light key pad and Supervisor settings To change any of these settings press the ESC key to enter the Main menu and select Analyser Settings Use the soft keys to select the submenus Display contrast On the display contrast screen a bar graph is displayed showi
17. e Measurement Let by Tightness Test Dedicated test and report print structure for combined test to IGE 11 UP 1B Pressure Scale Range 150 mbar to 150 mbar Resolution 0 1 mbar Accuracy 0 5 of reading calibration at 50 mbar equivalent to 0 5 mbar Equivalent scales Pa hPa kPa PSI inWG mmWG inHG mmHG Communications IR Port USB 20 TELEGAN gas monitoring Sprint V2 Accessories and spare parts X Accessories and spare parts Accessory list Telegan part number Description General Spares CAS29002 SFW29001 PRB29002 PRB29000 TUB29000 ENC29001 CHG29001 FIL29001 INS29602 FIL99008 C01296 TELEGAN gas monitoring DNDMNNANNANANANNA YN PRINT V CARRY CASE PRINT V CD ROM PRINT V LEAK PROBE PRINT V MAIN PROBE INC WATER TRAP WITH FILTER PRINT V Neoprene Tube 1 4 ID x 3 8 OD 6 35 mm x 9 53 mm PRINT V PROTECTIVE BOOT WITH MAGNETS PRINT V UK CHARGER PRINT V WATER TRAP INC FILTER PRINT V2 INSTRUCTION CARD A5 LTER ELEMENT HARGING LEAD FOR VEHICLE LIGHTER SOCKET Logging Sprint V2 VI Logging Sprint provides the option to log the results of tests When a test is complete use the soft key la to log the results The display will show the Create log screen detailing the log number log title date and time Press the accept key v to Store log The log details recorded are then displayed on the screen Press the M key to
18. e is drawing near If the calibration due date has passed the Sprint unit will display a message Calibration overdue 4 2 Water trap The combined filter and watertrap is used in line between the probe and the unit Before performing any tests check that the filter is clean and there is no water inside the trap Filter Arrow keep arrow upright A flue gas analysis The filter element should be changed if the filter has Wyarning Filters become contaminated or dirty If the filter has become must be used at all soaked with water remove from trap and leave to dry times Failure to do before reusing Ensure O ring remains in place so may invalidate the warranty To change the filter Unscrew the filter housing remove the old filter and replace Water To empty the water trap unscrew the filter housing remove the bung and empty Replace bung after emptying 18 TELEGAN gas monitoring Sprint V2 Specification V Specification Instrument Operating temperature range 10 C to 50 C 14 F to 122 F Battery Lithium lon Life up to 9 hours dependant on test used 15 left warning Recharge time Minimum 6 hours from flat Charger input voltage 230 V 50 Hz AC Standard Fuels Natural gas LPG heavy oil light oil coal wood coke Biomass and BAGASSE Display Blue back lit graphic LCD Menu Intuitive structure tab selection on screen Dimensions 75
19. e use Do not substitute components as this may impair safety and invalidate warranty Observe all warnings and instructions marked on the unit and within this manual If this product is not working properly read the trouble shooting guide or call Anton Ensure qualified service personnel change sensors and provide maintenance and calibration Additional information Sprint is designed to support the working practices defined in British Standard BS7967 and the Design Standards EN50379 BS7927 for flue gas analysers It is highly recommended that users are fully conversant with BS7967 when using a flue gas analyser for servicing or installing a boiler system Sprint offers a timed let by tightness test in accordance with the UK s Institute of Gas Engineers procedure IGE 1 1 UP 1B Performing CO measurements When performing any CO measurements ensure the unit is zeroed in clean air in accordance with British Standard BS7967 A suitable location for sampling clean air will be outside of the building where the boiler system is installed 1 Repair of this equipment and gas sensor replacement shall be carried out by the manufacturer or certified service centre in accordance with the applicable code of practice If the equipment is likely to come into contact with aggressive substances then it is the responsibility of the user to take suitable precautions that prevent it from being adversely affected The equipment is onl
20. ecovering from high CO exposure Return for service ASAP or ensure unit is purged and allow sensor to recover Sometimes negative CO readings are dis played High CO exposure zeroed in auto zero sequence Turn off and on and repeat auto zero in clean outside air allowing time for the CO sen sor to recover and stabilise Sometimes gt or I lt is displayed in place of a number Sensor is out of range Contact support for advice Return for service if problem persists or other failures are observed Cal due date has changed Time date has been amended Check current date and time is correct If the cal due date is set to more than a year s time then return for service ASAP TELEGAN gas monitoring 25 Appendix Carbon Monoxide Room Safety Tests Sprint V2 Appendix I Carbon Monoxide Room Safety Tests Sprint V instruments are designed to assist heating engineers to work to the BS 7967 2005 specification for carbon monoxide room safety testing You should refer to BS7967 which defines the requirements details the methods as well as the pass and fail criteria for various types of appliances CO Room Safety Test in the Sprint V instruments is designed to measure the build up of carbon monoxide levels in a room where a gas appliance is in use and record those values each minute for the duration of the test In addition at the end of the test it assists the e
21. elect Analyser Settings gt Supervisor settings if the password has been set enter the password now select one of the following options Set date amp time use the soft keys and to change units of date and time and gt to select hours minutes day month and year Press ESC to save Edit report header use the soft keys and to select header text one or two and to edit text Use the 92 and 9 keys to scroll through character lists and character values Press gt to move on to the next letter in the header text Press ON OFF ENTER to delete all characters to the right Press gt to move the cursor to the end of the text and M to accept change and return to Edit report header screen Press ESC to exit edit without saving changes TELEGAN gas monitoring Sprint V2 Quickstart guide Change password press the soft key to edit password Use the 92 and 9z keys to scroll through character lists and character values Press to move on to the next letter in the password Press gt to move the cursor to the end of the text and M to accept change and return to Password screen Press ENTER to store the change Retrieving stored logs From the Main menu select Stored logs and one of the following options Select a log use the soft keys to scroll and select log Find a log by number use the soft keys to scroll up and down the numbered logs database Delete all logs this option will delete all stored logs Press a
22. he one s supplied Failure to comply could invalidate the warranty and may result in permanent damage to the unit 2 TELEGAN gas monitoring Sprint V2 Overview Overview Display Showing start up splash screen Tel 44 0 870 428 0075 Fax 44 0 870 428 0076 sales anton group com www anton group com Battery icon Anton Group Soft keys Tel 44 0 870 428 0075 Three bars show complete charge Use these unmarked buttons p 9 to make selections from the Purge icon menu start and stop tests Rotating icon shows print and store results pump is purging See section Operation for more details ON OFF ENTER key Press and hold button for two seconds to switch on and switch off Sprint unit Use this key to finish edits save changes and sequence flue gas analysis pages ESCAPE key Use this button to quit tests and step back through menus Thermocouple sockets K type connectors Pressure inlets Power jack USB connector Connect gas leak probe here Also used for communications to PC Exhaust exit Warning do not inhale exit gas exhaust or block exit IR window Printer output senses ambient light to control backlight Tip to quickly activate backlight cover this window TELEGAN 3 gas monitoring Probe connections Sprint V2 L 5 ia T PRESSURE a Ww Tip see label frus SAMPLE underneath unit L PRESSURE for deta
23. ill after auto zero Always start in clean air Press and hold the ON OFF ENTER key for two seconds Sprint will emit a few ris ing beeps performs a screen test and starts the pump to purge any residual gas from the unit Ensure the gas exhaust outlet is not blocked p SSE The welcoming splash screen is displayed for approxi Main Menu i mately 30 seconds and will automatically go to the Auto 14 44 27 08 Feb 2006 zero screen When Auto zero is complete the display will i i change to the Test menu Warm up should be extended if sensor needs to recover from previous gas exposure crn renani a Analyser Settings Tip see soft key Stored Logs icon list on the inside front cover of this manual Auto zero When Sprint has completed warm up the auto zero screen will be displayed Ensure you are in clean air before proceeding Tip auto zero Sprint outside of the building or well away from the heating appliance to avoid any potential gases in the vicinity affecting the auto zero process Ensure the sensor reading is stable press the proceed v key to ssl auto zero After a successful auto zero Sprint will display the Jest 9 menu screen and switch off the pump i Auto zero D 14 44 27 08 Feb 2006 Note Sprint will switch off the pump when not performing tests or purging Purged in clean air f and readings stable Stable _ Tip check sensor co o reading is stable pm i Otherw
24. ils of probe connections FLOW je RETURN TEMPERATURE Flue gas analysis Connect the flue probe to the flue sample inlet and the thermocouple to the k connector marked FLOW Efficiency Differential pressure let by and tightness test Connect tubing to pressure inlet s Sprint will display a warning if the tubes are connected incorrectly Differential temperature test Connect one or two thermocouple probes to the k type connectors When using one probe Sprint will display a soft key option to switch between T1 and T2 snapshot measuring points Room CO safety test Connect CO room safety test probe optional where suitable to the flue sam ple inlet Gas escape test Connect gas leak probe to the USB connector Note The pump will operate at different speeds or switch off depending on the test being performed This will vary the pitch of the sound from the pump and does not indicate the pump is performing incorrectly Accessories Sprint is supplied with a rubber boot for protection of your Sprint unit A mag net on the reverse of the rubber boot can be used to place the Sprint unit in location on the boiler system for easy hands free operation 4 TELEGAN gas monitoring Sprint V2 Quickstart guide Quickstart Guide Important please connect flue probe first before switching on your Sprint unit ensure the water trap is empty and is fitted in the right direction Do not insert probe in flue t
25. in these tests Diff press is the difference between start and finish pressures 1 2 3 Select Pressure Menu from the Test menu From the Press menu select Let by Tightness Connect tube to positive pressure inlet but not pressure source Zero pressure use the soft key marked 5 Connect tube to pressure source to begin pressure test Sprint will give a warning if the pressure points are the wrong way round Press the soft key p to start test Sprint displays the duration time on the screen To stop test press the soft key m Press the soft key v to pass test and proceed to Tightness test You may fail the test by pressing the key x to indicate test has failed you can print the results Let by 14 44 27 08 Feb 2006 14 44 27 08 Feb 2006 Start P1 Start P1 mBar 0 0 mBar 0 0 Finish P2 0 0 i Finish P2 0 0 Let by Let by 14 44 27 08 Feb 2006 Start P1 mBar 0 0 Finish P2 Bar 0 0 Duration 00 25 Diff press 0 0 Diff press 0 0 Diff press 0 0 mBar mBar mBar Duration 00 00 Duration 00 54 Passed gt S E S x v m SSS Screen 1 Screen 2 Screen 3 Tightness Test 1 2 3 ui Connect tube to positive pressure inlet but not pressure source Zero pressure use the soft key marked So Connect tube to pressure source to begin pressure test Sprint will give a warning if the pressure points are the wrong way round Press the sof
26. ing off Use of the charger as a power adaptor The Sprint charger can be used to power the unit and will continue to charge whilst operating the unit Automatic battery saver The Sprint unit will automatically power down if left unused unless Auto off disabled The auto off timeout can be set in Analyser settings Charging the batteries Warning Do not attempt to use any other charger with this unit except the one s supplied Failure to comply could invalidate the warranty and may result in permanent damage to the unit 1 Plug the charger into a mains socket 2 Connect the charger to the Sprint using the power jack on the side of the unit Switch on the power at the mains socket The unit would normally be left switched off for charging The display will show the battery charging mains connection icon When the battery is full both icons will flash TELEGAN K gas monitoring Maintenance and calibration Sprint V2 IV Maintenance and calibration General To keep the display panel and operator buttons free from dirt build up regularly wipe over your Sprint unit with a slightly damp cloth Protective boot To protect Sprint from dirt and knocks a rubber boot is supplied This boot is supplied with concealed magnetics in the rear 4 1 Unit The Sprint should be calibrated once a year Your Sprint unit will also display the calibration due date at switch on and will warn you when calibration due dat
27. ise Sprint ozy 20 9 will display Not I stable and arrow a la I will tilt up or down AI TELEGAN 5 gas monitoring Quickstart guide Sprint V2 Using the menu Press the ESC key to display the Main menu Use the soft keys to scroll select and edit menu items see icon list inside front cover Press accept MI to make change or the ESC key to cancel Press the ESC key to return to the Main menu Changing fuel units and efficiency options From the Main menu select Fuel Options or Units of Measurement Fuel Options select one of the following options natural gas LPG heavy oil light oil coal wood coke Biomass and BAGASSE Units of Measurement select one of the following options Pressure units mbar Pa hPa kPa PSI inWG mmWG inHG or mmHG Temperature scale Centigrade or Fahrenheit Efficiency Net or Gross Net efficiency may be used for condensing boilers See section Setting up for more details Changing display and key pad settings From the Main menu select Analyser Settings and one of the following options Display contrast use the soft keys to adjust the contrast level Auto off timeout use the soft keys to adjust or disable the timeout period Back light use the soft keys to select one of the following options off dim bright or controlled Key click use the soft keys to enable or disable audible key click Changing date amp time report header and password From the Main menu s
28. ng the level of contrast Use the soft keys lt and gt to reduce or increase the level of contrast Press the M key to accept the change or ESC to cancel Auto off timeout On the auto off timeout screen the number of minutes at which the unit will automatically switch off is shown Use the soft keys and to reduce or increase the number of minutes Press the M key to accept the change or ESC to cancel To disable Auto off timeout press key until disabled is displayed Back light The back light can be set to four options off dim bright or controlled Use the soft keys to scroll and select the option desired Press the M key to accept the change or ESC to cancel TELEGAN ji gas monitoring Setting up Sprint V2 Back light options are Off switches the backlight off Dim lowers the light intensity Bright increases the light intensity Controlled Sprint monitors the ambient light level and adjusts the light intensity accordingly Key click The Key click settings allows you to enable or disable the key pad from making audible clicks when pressed Use the soft keys to select enabled or disabled from the submenu Press the M key to accept the change or ESC to cancel Supervisor settings Set date amp time On the Time amp Date screen the current time and date are shown Use the soft keys and to alter the values of hours minutes day month and year Use the gt key to select each unit Pre
29. ngineer in an advisory capacity only to deter mine whether the test has passed or failed or if the results are invalid In certain circumstances where the results are borderline or open to interpretation the instrument will ask the operator to decide if the test has passed or failed and will record the operators decision Please note ultimately it is the responsibility of the operator to ensure that the test is correctly performed to the BS 7967 2005 specification If the data does not support the result or the operator suspects it is not reliable due to local conditions such as carbon monoxide level changes due to cigarette smoke or vehicle traffic or incorrect then either the test should be repeated or the operator should seek expert advice CO Room Test Pass and Fail Test Specifications Type C Type B Type A Type A Type A Room sealed Boiler Cooker Water heater Space heater appliance open flue flueless _ flueless flueless Max Allowed CO 10 ppm 10 ppm 30 ppm 10 ppm 10 ppm Max Peak Duration 60 secs 60 secs 20 mins 30 secs 60 secs exceeding Max Allowed CO CO Alarm Level 30 ppm 30 ppm 90 ppm 30 ppm 30 ppm Min Test Duration 15 mins 15 mins 20 mins 5 mins 30 mins Max Test Duration 30 mins 30 mins 30 mins 10 mins 30 mins Result Codes The pass or fail result is displayed when the test completes and is printed on the report as well as recorded in the log If the test fails a code number is also displaye
30. o the test will fail The test will also fail if there is a significant build up of CO levels at the end of the test and levels are still rising or the CO level in the last minute of the test is not lower than the overall peak CO reading The result code is FAILED 1 CO Level Exceeds Max Allowable Level and Peaks for Unknown Duration If the CO level exceeds the maximum allowed too close to the end of the test then the test is failed This can occur if there is a build up of CO levels towards the end of the test or the appliance fires up late on in the test or the test is stopped too early The test should be repeated if this occurs The result code is FAILED 2 CO Level Does Not Start Close to Zero It is important that the instrument is zeroed in clean air at switch on Failure to do so will invalidate the test result BS 7967 2 2005 also requires that the room is well ventilated prior to starting the test However it is possible that there may be a residual background CO level eg due to traffic fumes The instrument will display a pop up box prior to starting the test if the CO level is more than 2 5 ppm TELEGAN 29 gas monitoring Technical helpline Tel 44 0 870 428 0075 Manufactured by Telegan Gas Monitoring A division of Crowcon Detection Instruments Ltd 2 Blacklands Way Abingdon Business Park Abingdon Oxfordshire OX14 1DY United Kingdom Tel 44 0 1235 557700 Fax 44 0 1235 557749 Email sales
31. obe from flue Continue to use the instrument as normal Pump flow fail alert Filter water trap or sample line blocked Empty and clean filter water trap Ensure sample line is free from blockage Printer does not respond or report con tains odd characters Printer may be off faulty out of range incorrectly set up have a low battery or not facing Sprint Ensure printer is charged up and turned on working set up correctly with PC protocol within physical range usually 1m and with the IR window facing the IR window on Sprint Other IR sources such as a PC or sunlight may give odd char acter print out 24 TELEGAN gas monitoring Sprint V2 Troubleshooting guide Symptom Cause Recommended User Action Auto zero failed Sensors exposed to gas or faulty Switch off and on ensuring you zero in clean air and sen sors are purged If unit contin ues to fail auto zero return for service Alarm activates in CO Room safety test CO is reading greater than 30ppm Dependant on safety proce dures Cannot remember the supervisor password Forgotten Supervisor password prevents alteration of report header which identifies owner of the instrument This provides secu rity against theft So there is no method to remotely unlock the instrument Return for reset During auto zero the CO reading does not stabilise CO sensor faulty or r
32. per roll installed and ready for use Ensure that the IR window on Sprint is aligned with the IR window on the printer The printer may be up to 1 m away from the Sprint unit If a report can be printed a printer icon will appear on the screen Press the soft key under the icon for an instant print Ensure printer is set to PC or suitable mode TELEGAN 23 gas monitoring Troubleshooting guide Sprint V2 Vill Troubleshooting guide Sprint will provide on screen messages which advise clear actions Contact Anton if unsure on how to proceed turn on and charger symbol is not displayed when charger is con nected Symptom Cause Recommended User Action Instrument will not Battery flat Connect charger and retry turn on when on off Battery may be flat The instru button is pressed and ment is designed to prevent held for 2 seconds deep discharge occurring and will turn it self off when battery level gets too low Instrument will not Battery flattened Ensure charger is correct type beyond standard charging point If so plug in and leave con nected Check to see if charg ing symbol appears every 4 6 hours If it does not and unit does not switch on return both unit and charger for serv ice Pump sometimes stays on at a faster rate par ticularly when exiting the Flue Gas Analysis or CO Room Test Smart purge is oper ating CO sensor is recovering from expo sure to gas Remove pr
33. ss the ESC key to accept the change Edit report header Use the soft keys and to select the report header text line one or two Press key to edit text The screen displays the character lists and highlights the current list in use Use the 92 and 9 keys to scroll through character val ues in each list and gt to move on to the next letter in the header text The character lists are shown below Press ON OFF ENTER to delete characters to the right Press gt to move the cur sor to the end of the text and M to accept change and return to Edit report header screen Change password Press the soft key to edit password Use the 92 and 92 keys to edit or create a password as described above in Edit report header Press M to accept change and return to Password screen Press ON OFF ENTER to store the change When a password has been created Sprint will display the Supervisor pass word screen on entering Supervisor settings Land amp 4 _ 09 0123456789 c gt A Z Uppercase alphabet a Z Lowercase alphabet Space 16 TELEGAN gas monitoring Sprint V2 Battery charging lll Battery Charging The Sprint has a lithium ion rechargeable battery and will operate for up to 9 hours when fully charged depending on the type of test used Low battery When the battery is low Sprint will display a low battery icon If the battery gets too low then Sprint will give further warning before switch
34. t key p to start test Sprint displays the duration time on the screen To stop test press the soft key mm Press the soft key v to pass test You may fail the test by pressing the key x to indicate test has failed TELEGAN 9 gas monitoring Performing tests Sprint V2 Tightness 14 44 27 08 Feb 2006 Tightness 14 44 27 08 Feb 2006 Tightness 14 44 27 08 Feb 2006 Tightness 14 44 27 08 Feb 2006 Str 3 0 0 stops 0 0 steps 0 0 siop 0 0 Finish P4 0 0 Finish P4 0 0 Finish P4 0 0 Finish P4 0 0 Diff pros 0 0 Di press 0 0 gt igres 0 0 ogres 0 0 Duration Duration Duration Duration 00 125 5 5 Passed x v PASSED gt No E Bo S Screen 1 Screen 2 Screen 3 Screen 4 At the end of the tightness test you can log or print the results Press the ESC key to return to Press menu Press ESC again to return to Test menu 3 Pressure and Differential pressure tests Before carrying out the test the pressure must be zeroed with the tubes con nected to the instrument but not the pressure source A thermocouple may be connected to provide temperature readings in these tests 1 Select Pressure Menu from the Test menu From the Press menu select Pressure or Diff Pressure 2 Connect tube s to pressure inlet s 3 Zero pressure use the soft key marked 4 Connect tube s to pressure source s neue to begin pressure test
35. vel within the max peak duration time It is up to the operator to determine if the result is acceptable or not If the operator chooses to fails the test the result code is FAILED 4 Otherwise the result code is PASSED Other Cases When a test is not performed correctly the results are inconclusive or there is insufficient or unreliable data Sprint V attempts to interpret the readings detected and fail the test It is possible for the results of a test to appear to be valid when it was performed incorrectly or the data collected was unreliable in some way Please refer to BS7967 2005 and ensure tests are carried out cor rectly Sprint V tries to reject incorrectly taken test readings but should not be relied on to instruct engineers on correct working practice 28 TELEGAN gas monitoring Sprint V2 Appendix Carbon Monoxide Room Safety Tests Multiple Peaks of CO The overall peak CO reading recorded will be the latest peak CO reading that was higher than any previous The peak duration recorded will be the total time the CO readings exceeded the maximum allowed CO level The pass fail criteria are applied as before based on this information Sprint V does not expect to record multiple peaks of CO where the reading goes up and down more than once Unstable or Rising Levels of CO If the CO level in the last minute of the test is not lower than the overall peak CO reading then Sprint V assumes that the CO level has not fallen s
36. y certified for use in ambient tem peratures in the range 10 C to 50 C and should not be used outside this range Use only charger s supplied by Telegan Anton Use only the appropriate Telegan Anton supplied cables for connection to the sockets on the instrument Copyright Telegan Gas Monitoring 2006 All rights are reserved No part of the document may be photo copied reproduced or translated to another language without the prior written consent of Telegan Gas Monitoring Publication number M09999 First edition July 2006 Contents Sprint V2 Multi function Flue Gas Analyser 00 cceeeeeee 2 WIAA IG ss siecle esate E E E E EEI EIET 2 OVEMIEW e aone e a E A N S 3 Prope CONNMECHONS ictevnedshuavicduscseacdvbasdsoapscessddchacaracsansrnadshasnensianamddthacandiie 4 Quickstart GUO ivicisstevicovensbevuntivntutstedainensesuuaddewiedadeceaurcenate 5 Operation as tetsu wets ev aatsestoain gilt dye ata iamentteatea a ddl easels 13 1 1 Menu and operator button Overview cceccccceccccecssceecesseeseesaeees 13 l Sening Vp aaenerer ee neeenre re Tree nrrce rrr rere rar acter re rrrrt re rrr re 15 2 WCONMGUNATION OPTIONS cs dtcrazcesdanscanatersoneseasthyrsceesenenenicas dey aaseauveces 15 Ill Battery Charging a asi tvalictantas oeniiiaai etter ticenairenndaeens 17 Charging the batteries ccceccccccecceeeceeeeceeeeeeeeeeeeeeeeseeessseeetseeensees 17 IV Maintenance and calibration cccccc
Download Pdf Manuals
Related Search