Si4010 Development Kit User`s Guide
Contents
1. USE debug adapter J0 pin header corector VBUS 4 56 C be wed i generate local VDD SPIOB For appii atom inidirectiional use isolated from the C2 Rev 0 1 11 SILICON LABS Si4010 DK Facts about using the LED with IDE chain 1 The IDE chain can connect to the device only if the LED current driver is off and the LED is not lit 2 Once the IDE chain is connected to the device it blocks the device LED driver Therefore the application can be written in a normal fashion using LED as desired in the final application without worry of being dis connected from the debug chain The only limitation is that the LED will not be lit from the application dur ing the IDE debug session The user will still observe LED activity but that activity is related to the debug chain communicating with the device not the user application driving the LED 3 Once the IDE chain is disconnected from the device for example by pressing the Disconnect button in the IDE the device is released from halt and at the same time the blocking of the LED driver is removed From that point on the application behaves and runs as a regular application and the LED activity reflects what the application desires to do with the LED 4 Ifthe user wants to reconnect the IDE to the device the only requirement is that the LED must not be lit by the application and the C2 debug interface must be active not being actively turned off by the application Therefor2. d i The function is able to determine whether the device is connected to the IDE chain If it is not connected then the function turns the C2 interface off Once that is done it is not possible to turn the C2 interface back on unless the power to the device or at least to the digital portion of the device is cycled See the discussion below about advantages and disadvantages The following is an example of how to use the vLedOn function Clear the GPIO_LED off after reset reset will set this bit GPIO_LED 0 Set LED intensity acceptable values are 0 off or 1 2 and 3 vSys_LedIntensity 3 Turn the LED on at currently set intensity vLedOn Turn the LED off keep the intensity setting GPIO_LED 0 Following are the advantages and disadvantages of this solution Advantages 1 Uniform code no need for conditional compilation the GPIO4 and LED will function as expected under all scenarios 2 The user can use the GPTO_LED 1 in the code which will block the GPIO4 But subsequent call to vLedOn will clear the blocking of the GPIO4 and it will start functioning normally again Disadvantages 1 Once the LED is physically blinked then it is not possible for the IDE to connect to the part until the power is cycled or the vSys_Shutdown is called from within the application It is up to the user to make sure that the power is cycled 2 If the pa
3. Si4010 gt XREG Regs The last item bREV_ID is the device revision The user can also call the API function bSys_GetRevlId 2 The trim version can be read by the Silicon Labs IDE as External Memory through Views gt Debug Win dows gt External Memory at location 0x11D6 There is a macro bSys_TrimId_c defined in the headers for use in customer code as well The user needs to know the Trimld before writing any code so the man ual access to it is adequate The trim version will rarely change and customers will be notified about the change The provided NVM burner program reads both the bREV_ID device revision and the trim version bSys_TrimId in the Device tab after the burner is connected to the device 2 7 Debugging Application which Drives LED To maximize utilization of the package pins the LED current driver output is shared with the debug chain clock signal C2CLK To share the functionality and be able to use the IDE for debugging there are some limitations to note and rules to follow The following figure shows the recommended connection of the USB 10 pin debug header to the device in the user application Note The LED must be isolated by the 470 Q resistor for the debug chain to work Custom er development board connections to support Si4010 debug chain YDD VY Fpushiutton on keyfob development board thenit has to be isolated by RS For debugging chain to work LED must be isolated by RG im max
4. GPIO_LED reset will set this bit GPIO_LED 0 To turn the LED on and off inside the user application Set LED intensity acceptable values are 0 off or 1 2 and 3 vSys_LedIntensity 3 To turn the LED on at currently set intensity GPIO_LED 1 To turn the LED off keep the intensity setting GPIO_LED 0 12 Rev 0 1 SILICON LABS Si4010 DK The intensity setting can be changed any time even when the GPIO_LED 1 This is basically how the LED control operates This approach will work when the part status is finalized as the Run device since for that program level the C2 interface is turned off after the boot by boot routine However when the code above is used for a device in the Factory or User programming state then the GPIO4 will stop working after the first LED blink The LED must be seen to be turned on and off by the application to blink to experience this problem 2 8 2 Solution 1 Living with the Limitation The simplest solution is to know about the issue and decide to live with it After the first LED blink the GPI04 will not work In this scenario the user may decide to test the GPI04 only when the part is fully programmed as the Run part 2 8 3 Solution 2 Controlled Compilation The user may use a define C statement to define a LED on value For button press debugging purposes when the LED can be off the code is compiled with value set as 0 so
5. SILICON LABS Si4010 DK Si4010 DEVELOPMENT KIT USER S GUIDE 1 Key Fob Development Platform The Si4010 key fob development platform is a flexible platform for comfortably developing software and testing the whole system using the Silicon Laboratories software development IDE The platform also allows programming of the NVM on chip The kit has three versions one for the 434 MHz band P N 4010 KFOBDEV 434 one for the 868 MHz band P N 4010 KFOBDEV 868 and one for the 915 MHz band P N 4010 KFOBDEV 915 1 1 Kit Content Table 1 Kit Content Qty Part Number Description 4010 KFOBDEV 434 Si4010 Key Fob Development Kit 434 MHz 2 4010 KFOB 434 NF Si4010 key fob demo board 434 MHz w o IC 1 MSC DKPE1 SOIC MSOP socketed development board 3 Si4010 C2 GS Si4010 C2 GS transmitter IC SOIC Package 1 4010 DKPB434 BM Si4010 MSOP key fob development board 434 MHz SMA 1 4355 LED 434 SRX Si4355 RFStick 434 MHz receiver board 1 MSC PLPB_1 Key Fob Plastic Case translucent grey 1 MSC BA5 Programming interface board 1 MSC BA4 Burning adapter board 1 EC3 USB Debug Adapter 1 Toolstick_BA Toolstick Base Adapter 1 MSC DKCS5 USB Cable 1 USB extender cable USBA USBA 2 AAA AAA battery 2 CRD2032 CR2032 3 V coin battery 4010 KFOBDEV 868 Si4010 Key Fob Development Kit 868 MHz 2 4010 KFOB 868 NF Si4010 key fob demo board 868 MHz w o IC 1 MSC DKPE1 SOIC MSOP socket
6. and the part goes through a boot sequence 2 Every time the new code in OMF or HEX format is downloaded to the part through the IDE the IDE issues a system reset and the device reboots The content of the RAM memories is not touched by the boot with the exception of the API reserved regions in CODE XDATA and DATA IDATA memories The register banks RBO RB1 and RB are cleared by the boot routine 3 Whenever the ToolStick adapter is directly connected to the key fob design platform and the IDE is con necting to the part the GPIOO will be forcibly driven to 1 for about 260 ms around the beginning of the con nection sequence In the Silicon Labs provided key fob platform the GPIOO isolated by a resistor then if the user is pressing a GPIOO button during the connection sequence the GPIOO value will be viewed as 1 by the internal CPU during the IDE connection to the device 4 Itis recommended that the user uses the Burning adapter board along with the USB Debug Adapter Rev 0 1 17 SILICON LABS Si4010 DK 3 Examples provided There are 5 demonstration examples provided with the development kit documentation pack aes demo fcast_demo fstep_demo tone_demo keyfob_demo tke_demo All are precompiled and ready to be used without compilation for convenience The user just needs to go to the lt name gt _demo bin directory and open the Silicon Labs IDE wsp project file by the Silicon Labs IDE Each demo can be
7. built and debugged from within the Silicon Labs IDE Ooah oN 3 1 AES demo aes_demo AES example with timer usage example The timer counts the number of system clock cycles needed to run encryption decryption key preparation and decryption 3 2 Frequency casting demo fcast_demo This example shows the main flow when using the main vFCast_Tune tuning function It also shows how to transmit a predefined data packet when a button is pressed The buttons are not debounced in this simple example 3 3 Frequency casting two step demo fstep_demo This example shows the main flow when the user wants to switch in between several frequencies fast It is possible to call vF Cast_Tune for several frequencies in advance collect the information calculated and then just quickly apply it during transmission This is for the cases when the 5 6 ms time spent in vFCast_Tune _ is prohibitive for switching in between frequencies 3 4 Tone CW generation demo tone_demo This example shows the steps to generate continuous wave tone at a desired frequency There are two main files compiled to two separate example applications tone_demo Run main tune vFCast_Tune once then use only fine tuning to track the temperature changes tone_demo_ptune Periodic tuning run main tune vFCast_Tune every minute and use the fine tuning only in between the main tuning events However there will be about 6 ms interruption of the output during the main tuning onc
8. e if the device user software is stuck in an infinite loop and driving the LED constantly or the C2 interface was turned off by the application the IDE chain will not be able to connect to the device In such a situation the device power has to be cycled to invoke internal power on reset See item 1 above Cycling the power to the part in this context means either physical removal of the power to the device or calling the vSys_Shutdown function from within the application which achieves the same result 2 8 Hardware Issue with Debugging LED Application There is an issue with the LED turning on and off and the functionality of the GP104 There is no issue when the part is programmed as the Run part and runs the final application code Therefore the issue affects only the application development There are several possible software workarounds depending on the approach the user wants to take 2 8 1 Application LED Control The user can control the LED intensity and whether the LED is on or off The LED intensity has 4 values 0 to 3 Off 0 3 mA 0 6 mA and 1 mA current The user can set the intensity any time but the LED is not going to be turned on until the GPIO_LED is set to 1 The GPIO_LED is an alias for the PO 5 bit After the reset the P0 5 bit is set to 1 so it is recommended that the user use GPIO_LED 0 at the beginning of the user application To turn the LED off at the very beginning of the user application Clear the
9. e per minute The Keil Vision project tone_demo Uv2 covers both targets tone_demo tone_demo_ptune For the Silicon Labs IDE there is only one target per wsp file so there are two project files tone_demo wsp tone_demo_ptune wsp 18 Rev 0 1 SILICON LABS Si4010 DK 3 5 Simple key fob demo keyfob_demo This example demonstrates a basic key fob application transmitting a packet for every button push Packets can be received by an 4355 LED XXX SRX board Buttons are debounced using the Button Service API functions 3 6 RKE key fob demo rke_demo An advanced key fob demo using AES encryption rolling counter in MTP memory battery voltage measurement and production ID of chip as node address This is the firmware used in the Si4010 Demo Key Fobs available in Silicon Labs key fob demo kits Rev 0 1 19 SILICON LABS Si4010 DK CONTACT INFORMATION Silicon Laboratories Inc 400 West Cesar Chavez Austin TX 78701 Tel 1 512 416 8500 Fax 1 512 416 9669 Toll Free 1 877 444 3032 Please visit the Silicon Labs Technical Support web page https www silabs com support pages contacttechnicalsupport aspx and register to submit a technical support request The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice Silicon Laboratories assumes no responsibility for errors and omissions and disclaims responsibi
10. ed development board 3 i4010 C2 GS S i4010 C2 GS transmitter IC SOIC Package 1 4010 DKPB868 BM Si4010 MSOP key fob development board 868 MHz SMA 1 4355 LED 868 SRX Si4355 RFStick 868 MHz receiver board Rev 0 1 6 12 Copyright 2012 by Silicon Laboratories i4010 DK Si4010 DK Table 1 Kit Content Continued 1 MSC PLPB_1 Key Fob Plastic Case translucent grey 1 MSC BA5 Programming interface board 1 MSC BA4 Burning adapter board 1 EC3 USB Debug Adapter 1 Toolstick_BA Toolstick Base Adapter 1 MSC DKCS5 USB Cable 1 USB extender cable USBA USBA 2 AAA AAA battery 2 CRD2032 CR2032 3 V coin battery 4010 KFOBDEV 915 Si4010 Key Fob Development Kit 915 MHz 2 4010 KFOB 915 NF Si4010 key fob demo board 915 MHz w o IC 1 MSC DKPE1 SOIC MSOP socketed development board 3 i4010 C2 GS S i4010 C2 GS transmitter IC SOIC Package 1 4010 DKPB915 BM Si4010 MSOP key fob development board 915 MHz SMA 1 4355 LED 915 SRX Si4355 RFStick 915MHz receiver board 1 MSC PLPB_1 Key Fob Plastic Case translucent grey 1 MSC BA5 Programming interface board 1 MSC BA4 Burning adapter board 1 EC3 USB Debug Adapter 1 Toolstick_BA Toolstick Base Adapter 1 MSC DKCS5 USB Cable 1 USB extender cable USBA USBA 2 AAA AAA battery 2 CRD2032 CR2032 3 V coin battery 2 Rev 0 1 SILICON LABS i4010 DK 1 1 1 Burning Adapter P N MSC BA4 The programming interface board ser
11. ff when lit then there will not be the GPIO4 problem To do that the user must add the following function to the user application to turn the LED on C function to turn the LED on K INCLUD include si4010 h Fl n 7 VISIBLE FUNCTIONS x void vLedon void os FUNCTION DESCRIPTION R urn LED on with disabling of the C2 es The C2 is disabled only if the part is not connected to the IDE debugging chain VARIABLES GPIO_LED 1 if 0 RBIT_DATA amp M_GPIO_LED_DRIV Gl lt PROTO_CTRL M_C2_OFF 14 Rev 0 1 S SILICON LABS Si4010 DK K Assembly version of the same function assuming that the file name is ledon a51 for Keil toolchain r T i INCLUDES i NOLIST SINCLUDE si4010 inc LIST i i SEGMENTS i Assumes file name to be ledon a5l capitalized LEDON is the file name NAME LEDON E PR vLedOn LEDON SEGMENT COD 7 EXTERNALS AND PUBLIC PUBLIC vLedOn F CODE RSEG PR vLedOn LEDON vLedoOn setb GPIO_LED mov A RBIT_DATA jnb ACC B_GPIO_LED_DRIVE NoC2Disable orl PROTO_CTRL M_C2_OFF NoC2Disable EC Rev 0 1 15 SILICON LABS Si4010 DK ret End of assembly END T
12. hen it notifies the user and requests permission to update the adapter s firmware Silicon Labs also provides a program usb_debug_adapter_firmware_reset exe to clear the adapter s firmware manually before connection to the IDE The program resides in the same directory as the IDE main executable With the Si4010 debugging chain it is required that the manual adapter firmware clearing is done for each USB adapter before using the key fob debugging chain That operation needs to be done only once per USB Debug Adapter The IDE will then program the correct firmware into the adapter The reset firmware executable will scan USB ports and give the user a list of connected Silicon Labs USB adapters The USB Debug Adapter name starts with EC Users can have more than one USB adapter connected to the computer 2 2 Keil toolchain integration The project files in examples assume that the Keil toolchain is installed into C Keil directory The location of the Keil toolchain can be easily changed in the Silabs IDE in the Project Tool Chain Integration menu An evaluation version of the Keil toolchain can be downloaded from the Keil website at http www keil com This free version has a 2 kB code limitation and starts the code at the 0x0800 address The Keil free evaluation version can be unlocked to become a 4kB version with no code placement limitation by following the directions given in application note AN104 about Keil toolchain integration and lice
13. indows the user must press the Refresh Values Alt R button on the toolbar to update the values in the device Just changing values in the IDE will not automatically update them in the device 2 4 IDE Debugging Session The typical IDE debugging session consists of the following sequence 1 Connect the IDE to the chip by hitting the Connect or invoking menu Debug gt Connect menu item 2 Download the OMF file either by hitting the Download code Alt D toolbar button or from the Debug Download object code menu item The latter also allows IntelHEX download but without the source code debugging capability 3 After the code download the device is automatically halted at address 0x0000 in CODE XDATA RAM Then the user can set breakpoints single step animate etc 4 The user can hit the Reset Ctrl R toolbar button any time the device is halted not running The internal digital system level reset is invoked and the device goes through the boot sequence The previously loaded code by the user into the CODE XDATA RAM is preserved and the device is halted at the address 0x0000 of CODE XDATA RAM 5 When a bug is found the user can download a new OMF file whenever the device is halted There is no need to disconnect the device from the debug chain or to hit reset The download item 2 above will auto matically reset the device after the OMF IntelHEX new code download is finished It is very important to note that whenever the Disc
14. lity for any consequences resulting from the use of information included herein Additionally Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters Silicon Laboratories reserves the right to make changes without further notice Silicon Laboratories makes no warranty rep resentation or guarantee regarding the suitability of its products for any particular purpose nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation conse quential or incidental damages Silicon Laboratories products are not designed intended or authorized for use in applications intended to support or sustain life or for any other application in which the failure of the Silicon Laboratories product could create a situation where per sonal injury or death may occur Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap plication Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders 20 Rev 0 1 SIL ICON LABS
15. nse management Unlock code can be found on the WDS CDROM in the root folder in the Keil_license_number txt file Contact your Silicon Laboratories sales representative or distributor for application assistance Rev 0 1 9 SILICON LABS Si4010 DK 2 3 IDE Features The IDE allows the following 1 Download the OMF 51 linker output format Keil BL51 linker output for example and match the source code lines with the compiled file This allows source code debugging including variable value viewing set ting breakpoints single stepping etc Note that the output of the Keil LX51 linker is not understood by the IDE 2 Download the IntelHEX file for the application When using the IntelHEX file the source code debugging is not available The user can set a breakpoint for a specific code address by going through the Debug Breakpoints Alt B menu item The user can also single step through the disassembly of the loaded code 3 Setting at least 4 breakpoints with a possible maximum of 8 The actual number of breakpoints available is determined by the IDE from the factory setting of the chip 4 Single stepping through the disassembly of the code If the OMF file is loaded the single stepping is matched with the source code 5 Viewing and changing variables SFR registers XREG registers and the contents of both DATA IDATA RAM and CODE XDATA RAM on the fly during debugging When the changes are made by the user in the corresponding w
16. ob Development Board 434 MHz SMA This board is similar to the board described in 1 1 3 Si4010 MSOP Key Fob Development Board 434 MHz SMA P N 4010 DKPB434 BM but contains the SOIC package version of the Si4010 1 2 2 Si4010 Key Fob Development Board 434 MHz This is also a key fob development board but with a pcb antenna instead of the SMA connector SILICON LABS Rev 0 1 7 Si4010 DK 1 3 Usage of the Key Fob Development Platform The Silicon Labs IDE communicates with the USB Debug Adapter through the USB bus The following debugging scenarios are possible 1 EC3 debug adapter Burning adapter Si4010 socketed key fob development board f or R This setup is suitable for downloading running and debugging the program in RAM or burning the program in the NVM and running it The antenna or measuring instrument can be connected through an SMA connector Since sockets on board allow use of unsoldered ICs this is the ideal scenario for burning the NVM memory of Si4010 2 EC3 debug adapter gt Burning adapter Si4010 MSOP key fob development board This setup is suitable for downloading running and debugging the program in RAM This board has a PCB antenna and battery so after downloading the program and starting the execution by disconnecting in the IDE the board can be physically disconnected from the programming interface and tested in mobile form A switch is provided on the board to connec
17. onnect toolbar button is hit or the Debug Disconnect menu item is invoked the debugging chain does the following e Enables the LED driver During the debugging sessions the LED current driver is forcibly disabled e Clears all the breakpoints e Releases the device from halt and lets it run from the point when it was halted 2 5 Important Note about Single Stepping Over ROM Code Single stepping through the ROM code is disabled Whenever the user encounters the call to the ROM API functions he or she should use the Step Over F10 toolbar button rather than the Step F11 or Multiple Step button Even though single stepping through the ROM API function using the Step F11 button works from the user s point of view the CPU timing is modified and real time performance is not guaranteed when using the Step F11 or Multiple Step buttons over the ROM API functions Therefore it is highly recommended to use the Step Over F10 toolbar button when stepping over the ROM API functions in IDE Single stepping over the bMtp_Write function using Step F11 or Multiple Step buttons may yield unpredictable results in the MTP EEPROM and is highly discouraged One should use the Step Over F10 tool run to cursor or setting a breakpoint when debugging around the MTP write function 10 Rev 0 1 SILICON LABS Si4010 DK 2 6 Device Version 1 The device ID information can be read through the IDE through Views gt Debug Windows
18. rt is programmed as the User part with the option to execute the user code after the boot automatically without stopping then the user application must not use the vLedon function just to blink LED without a user input If the application blinks the LED on its own then the IDE will not be able to connect to the part since the C2 interface is disabled at the time when the LED is turned on If the user does not use the option to execute user code without stopping after the boot there is not a problem since the device will load User code after the reset and wait for further instructions essentially waiting for the IDE to connect to it without executing the User code 16 Rev 0 1 ES SILICON LABS Si4010 DK 3 The vLedoOn function code is bigger than simple GPTO_LED 1 and is not necessary for the Run part so conditional compilation for LED bug may still be an option One recommendation for using the vLedon function is that the user application would include monitoring of several buttons pressed simultaneously If that combination happens then the vSys_Shutdown is invoked and the IDE chain would be able to connect to the part again That would satisfy the power cycling requirement without actually cycling the physical power to the device 2 9 Notes about USB Adapter Use The following facts are worth noting when using the IDE debug chain 1 Whenever the Reset button is pressed on the IDE the system reset is invoked
19. t disconnect the battery The Toolstick Base Adapter can be also used in the two above scenarios as a debug adapter It can be connected to the pcb edge connector of the burning adapter Note Although burning is also possible with this setup it is not practical since Si4010 is soldered on the key fob development board 8 Rev 0 1 SILICON LABS Si4010 DK 3 EC3 debug adapter Programming adapter User s own application TiL tO SOE osa v In this setup the user can incorporate the debugging capabilities into the final application using a cheap 4 pin header connection 2 Debugging an Application To debug an application the user is provided with the Silicon Laboratories IDE Integrated Development Environment The IDE has an integral help This section is not a user manual for the IDE but highlights the items which are important when working with the IDE 2 1 Installing the IDE and USB Debug Adapters Download the Silicon Labs IDE Integrated Dvelopment Environment from the following URL http www silabs com products mcu Pages SiliconLaboratoriesIDE aspx and install it on your computer The IDE gets installed into its own directory The main executable file is IDE exe The IDE works with the USB Debug Adapter or the Toolstick Base Adapter shown in the section above When the IDE recognizes the Silicon Labs USB debug adapters it queries whether its internal firmware is compatible with the Si4010 If not t
20. the LED will never light up and the GPIO4 will always function For debugging the LED and for final application compilation for the Run state of the device the user will compile the application with the LED on value set to 1 For example ifdef DEBUG define gLedOnValue_c 0 else define gLedOnValue_c 1 endif Clear the GPIO_LED off after reset reset will set this bit GPIO_LED 0 Set LED intensity acceptable values are 0 off or 1 2 and 3 vSys_LedIntensity 3 Turn the LED on at currently set intensity GPIO_LED gLedOnValue_c Turn the LED off keep the intensity setting GPIO_LED 0 One advantage of this solution is that the code size is identical in both cases Debug or Run Cycling the power to the part in this context means either physical removal of the power to the device or calling the vSys_Shutdown function from within the application which achieves the same result 2 8 4 Solution 3 Dynamic C2 Disable Recommended The GPI04 issue manifests itself when the LED is actually being turned on and off from the application The LED physically blinks and is not blocked from being lit up by an application being connected to the IDE debug chain and the C2 interface is active and enabled Rev 0 1 13 SILICON LABS Si4010 DK If we disable the C2 interface when the device is not connected to the IDE chain and before the LED is turned o
21. ver program srx_demo Can be used for link testing with Si4010 programmed with the rke_demo 1 1 5 Programming Interface Board P N MSC BA5 Adapter board for interfacing customer PCB to the debug adapter 4 Rev 0 1 SILICON LABS i4010 DK 1 1 6 4010 Key Fob Demo Board 434 MHz without IC P N 4010 KFOB 434 NF 1 1 7 Key Fob Plastic Case translucent grey P N MSC PLPB_1 1 1 8 Toolstick Base Adapter P N Toolstick_BA Debugging adapter compatible with Si4355 RFstick receiver board and the Si4010 development boards 1 1 9 Si4010 sample SOIC package P N Si4010 C2 GS 1 1 10 USB Cable P N MSC DKCS5 Cable to connect EC3 Debug Adapter to PC Rev 0 1 5 SILICON LABS Si4010 DK 1 1 11 EC3 Debug Adapter P N EC3 Silicon Labs debugging adapter used by other Silicon Labs MCU products as well compatible with the development platform we piam set iaaa anant of z Rev 0 1 SILICON LABS i4010 DK 1 2 Other Boards The following boards are not part of the development kit but can be ordered separately from Silicon Labs Part Number Description 4010 DKPB434 BS Si4010 SOIC key fob development board 434 MHz SMA 4010 DKPB_434 Si4010 key fob development board 434 MHz 4010 DKMX_434 Si4010 matrix keyboard development board 434 MHz 4010 KFOB 315 NF Si4010 key fob demo board 315 MHz w o IC 1 2 1 Si4010 SOIC Key F
22. ves as an interface in between the debug adapter and the Socketed Key Fob Development Board or the Development Key Fob It provides 6 5 V for NVM programming The power source is activated by a sliding switch on the board It is required when the user wants to program the internal NVM memory on the chip The programming interface board contains an 8 pin header to which GPIOO to GPIOS5 along with power and ground are connected from the development boards Therefore the user can tap to that header to control or monitor the chip pins 1 1 2 Si4010 Socketed Key Fob Development Board P N MSC DKPE1 Socketed both SOIC and MSOP key fob board with SMA connector Rev 0 1 3 SILICON LABS Si4010 DK 1 1 3 Si4010 MSOP Key Fob Development Board 434 MHz SMA P N 4010 DKPB434 BM This development board has an unburned soldered Si4010 five push buttons matched 50 Q SMA RF output battery clip and battery switch This board allows running user application from RAM during program development even while board is disconnected and powered by the battery The SMA output connector allows wired measurements of the RF output signal Note Instead of this board some 434 MHz development kits may contain the pcb antenna version of this board described in 1 2 2 Si4010 Key Fob Development Board 434 MHz on page 7 1 1 4 Si4355 RFStick 434MHz receiver board P N 4355 LED 434 SRX Receiver board factory programmed with the simple recei
Download Pdf Manuals
Related Search