Pinspot LED Quad DMX User Manual
Contents
1. 2 3 1 2 4 7 Unit 3 dip on 1 3 4 1 4 8 13 Unit 4 dip on 1 2 5 1 2 16 19 ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 8 ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 9 Pinspot LED Quad DMX UC IR Remote The UC IR infrared remote has many differnet functions and gives you complete control of your Pinspot LED Quad DMX To control the your desired fixture you must aim the controller at the front of the fix ture and be no more the 30 feet away STAND BY Pressing this button will blackout the fixture FULL ON Hold this button down to fully light up the unit When you let the button go the unit will return to its previous state FADE GOBO Invalid for this fixture COLOR Press buttons 1 9 to choose a desired color Adjust the output intensity using either the number buttons or using the DIMMER and DIMMER buttons STROBE Press and hold this button the to strobe This function is only valid under color mode SOUND ON amp OFF These buttons activate and deactivate the sound active mode SHOW This button will activate the random show default Press the buttons 1 9 to select a different show DIMMER and DIMMER Use these buttons to adjust the out put intensity in Color2. Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior DMX512 IN 3 PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT DMX512 DMX DMX COMMON 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture 1 2 3 1 2 3 DMX DMX COMMON DMX512 OT 3 PIN XLR Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion Conductor 5 Pin XLR Male In 3
3. LLC www adj com Pinspot LED Quad DMX User Manual Page 5 Pinspot LED Quad DMX Set Up To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties During long periods of non use disconnect the unit s main power Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to the poin
4. at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Stan dard Time Voice 323 582 3322 Fax 323 582 3108 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products LLC PLEASE recycle the shipping carton when ever possible Pinspot LED Quad DMX Safety Precautions ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 4 Power Supply The ADJ Pinspot LED Quad DMX contains a auto matic voltage switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Link
5. connections to any standard DMX controller Use dipswitches 1 9 to set your desired DMX address See below for example addressing 3 Please see the next page for the DMX values and traits ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 6 cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior Pinspot LED Quad DMX Set Up DMX512 IN 3 PIN XLR SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT SOUND REMOTE CONTROL INPUT POWER INPUT OUTPUT DMX512 DMX DMX COMMON 1 2 3 Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture 1 2 3 1 2 3 DMX DMX COMMON DMX512 OT 3 PIN XLR Figure 2 Figure 3 1 Ground 1 Ground XLR Male Socket XLR Pin Configuration 3 Hot 2 Cold 2 Cold 3 Hot XLR Female Socket Pin 3 Data True positive Pin 2 Data Compliment negative Pin 1 Ground
6. mode Master Slave Setup This function will allows you to link units together to run in a Master Slave mode In a Master Slave set up one unit will act as the control ling unit and the others will react to the controlling units built in pro grams Any unit can act as a Master or as a Slave however only one unit can be programmed to act as the Master 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR microphone cables to link your units together Remember that the Male XLR connector is the input and the Female XLR connector is the ouput The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only 2 Set the dipswitch 1 to the ON position all other dipswitches off for the Master unit 3 For the Slave unit s any dipswitch in the On position except 1 4 Connect the Slave unit or units and they will automatically start to follow the Master Pinspot LED Quad DMX Operating Instructions Pinspot LED Quad DMX 6 Channel Mode Channel Value Function 1 RED 0 255 0 100 2 GREEN 0 255 0 100 3 BLUE 0 255 0 100 4 WHITE 0 255 0 100 5 MASTER DIMMER 0 255 0 100 6 STROBING 0 7 NO STROBING 8 255 STROBING SLOW FAST Pinspot LED Quad DMX Cleaning Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses must be carried out
7. LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products
8. Pin XLR Female Out Pin 1 Do Not Use Do Not Use Pin 3 Pin 2 Pin 1 Pin 3 Pin 2 Not Used Not Used Data True signal Data Compliment signal Ground Shield 3 Pin XLR to 5 Pin XLR Conversion Universal DMX controller When using a universal DMX controller to control the chain of units you have to set DMX address with Dip switches from 1 to 9 to make sure all the units will receive a DMX signal Please refer to the following diagram for how to address your DMX 512 system using the binary code DMX 512 Address Chart Dip switches 1 2 3 4 5 6 7 8 9 10 Value 1 2 4 8 16 32 64 128 256 2 Light show Examples 6 Channels Mode Channel mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address 6 Channels 1 7 19 4 Unit 1 dip on 1 1 Unit 2 dip on 1
9. User Instructions Rev 3 15 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use Thank
10. age when it is plugged into the power source ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj com Tel 31 45 546 85 00 Fax 31 45 546 85 99
11. covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS Lighting Products 1 year 365 days Limited Warranty Such as Special Ef
12. fect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps Laser Products 1 Year 365 Days Limited Warranty excluding laser diodes which have a 6 month limited warranty L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty batteries which have a 180 day limited war ranty Only the L E D s carry a 2 year warranty excluding StarTec Series which a carries a 1 Year Limited Warranty Note 2 Year Warranty only applies to purchases within the United States ADJ DMX Controllers 2 Year 730 Days Limited Warranty excluding faders and tact switches Pinspot LED Quad DMX Specifications Model Pinspot LED Quad DMX SPECIFICATIONS Voltage 100V 240V 50 60Hz LEDs 1 x 8 Watt Quad RGBW LED Beam Angle 15 Degrees Power Draw 11 1W Weight 1lbs 0 4Kgs Dimensions 8 L x 4 W x 2 5 H 205 x 98 x 61mm Colors RGBW Color Mixing DMX Channels 6 DMX Channels Working Position Any safe working position Warranty 2 Year 730 days Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the volt
13. ing DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Pinspot LED Quad DMX can be controlled via DMX 512 protocol The Pinspot LED Quad DMX has 6 DMX channels please see page 7 for the DMX values and traits The DMX address is set using the dipswitches located on the rear of the Pinspot LED Quad DMX Your unit and your DMX controller require a standard 3 pin XLR connec tor for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX ADJ Products
14. mber on the outside of the package will be returned to the shipper Pinspot LED Quad DMX Introduction ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 2 Unpacking Thank you for purchasing the Pinspot LED Quad DMX by ADJ Products LLC Every Pinspot LED Quad DMX has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all accessories necessary to oper ate the unit has arrived intact In the case damage has been found or parts are missing please contact our toll free customer support number for further instructions Do not return this unit to your dealer without first contacting customer support Introduction The ADJ Pinspot LED Quad DMX is part of a continu ing pursuit to create high quality intelligent lighting The Pinspot LED Quad DMX is a DMX intelligent high powered LED par can This fixture can be used in a stand alone mode or connected in a Master Slave configuration The unit can also be controlled via DMX controller This unit has 3 operating modes Sound Active mode Auto mode and DMX control mode Customer Support ADJ provides a customer support line to pro vide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web
15. periodically to optimize light output 1 Use normal glass cleaner and a soft cloth to wipe down the outside casing 2 Clean the external optics with glass cleaner and a soft cloth every 20 days 3 Always be sure to dry all parts completely before plugging the unit back in Cleaning frequency depends on the environment in which the fixture operates i e smoke fog residue dust dew ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 10 Pinspot LED Quad DMX Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products
16. t they exit from the unit Cleaning The fixture should be cleaned only as recommended by t he manufacturer See page 9 for cleaning details Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances inclu d ing amplifiers that produce heat The fixture should be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance Figure 1 Pinspot LED Quad DMX Operating Instructions ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 7 Operating Modes Sound Active Mode 1 Plug the fixture in and put dipswitch 1 in the ON position Show Mode 1 Plug the fixture in and put dipswitch 1 in the ON position Dipswitches 4 5 6 will control the show speed DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your fixtures as spot lights The Pinspot LED Quad DMX has 6 DMX channels 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 To run your fixture in DMX mode plug in the fixture via the XLR
17. you PINSPOT LED QUAD DMX ADJ Products LLC www adj com Pinspot LED Quad DMX User Manual Page 3 Multi Colors 3 Operating Modes Electronic Dimming 0 100 Built in Microphone DMX 512 protocol 3 Pin DMX Connection 6 DMX Channels Pinspot LED Quad DMX Warranty Registration Pinspot LED Quad DMX Features To optimize the performance of this product please read these operat ing instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Pinspot LED Quad DMX General Instructions The Pinspot LED Quad DMX carries a two year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper included in the ship ping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by con tacting our customer support team on our customer support number All packages returned to the service department not displaying a R A nu
Download Pdf Manuals
Related Search