WIRELESS TTL FLASH TRIGGER
Contents
1. 0 ft B 360 degree angle Within 30 U pee BP A Approx 110m 360 ft 360 degree angle 110 meter Approx a 360 degree 360 degree angle Important Note The AK TTL AUTO mode needs a Commander Master unit on camera www aokatec com Setting 1 Mount TX on Commander Master flash unit A Mount TX on Pop up flash Mount TX on Master flash unit v Mount TX on Canon ST E2 Mount TX on Nikon SU 800 Note Mount TX unit on the Commander Master unit by Velcro supplied Ensure the SYNC connector side faces the same direction of flash head for better signal Adjust position of TX unit for best results 2 Connect RX and remote slave flash by ASC 1 sync cable Mount the ASC 1 IR sender on the slave flash wireless sensor window Make sure all TX and RX in the same Channel set on Channel switch Set the AK TTL s mode switch to AUTO on both TX and RX Then operate the original system as before no more limited by line of sight Note Mount ASC 1 sync cable IR sender to IR sensor window of remote flash If the IR sen sor window is larger use electrical tap cover most of it make sure the original optical signal can t get into it AUTO mode Compatibility 3 4 5 Completely compatible with Nikon iTTL CLS Creative Lighting System Canon optical Wireless E TTL flash system Pentax Wireless P TTL flash system Sony Wireless flash system Other compati2. Bracket for AK TTL TX and IR Panel for Sony camera How AK TTL Works Preparation Installing Batteries 1 Open the cover 2 Slide open the battery chamber lid in the right direction 3 Close the battery chamber lid by sliding it into place while pressing down Setting Channel Setting AK TTL TX amp RX into the same channel by channel switch www aokatec com AK TTL AUTO mode Include TTL Auto amp M flash setting Most of the original wireless Optical wireless flash limited flash system controlled by opti 7 cal signals Less than approx Fi In AUTO mode AK TTL TX re 10 m 33 ft sA _ Approx 5 7 m 16 4 23 ft ceive optical signal and con verts it to Radio signal then T a lt transmits to AK TTL RX RX M converts Radio signal back to o S Built in master flash optical signal to control slave TE TEE Remote flash flash ee Within LE a The AK TTL system retain all of A the original system such as 1 ee i HSS high speed ratio control ITTL CLS E TTL P TTL FV Lock NM gt remote setting manual power Na Approx 3 7 m 16 4 23 ft levels It s stable and expand working range up to 110 meter 360ft No limited to line of sight AK TTL radio wirless flash system Approx 110m 360 ft 360 degree angle 1 N N 21 N S Built in master flash D Within 30 amp AK TTL TX Approx 110m 36
3. ble brands and compatible camera models and flash models will be update on our website www aokatec com www aokatec com AK TTL M mode Manual flash setting In M mode AK TTL work as simple wireless flash trigger Remote trigger the flash wireless from the camera The flashes only work in manual mode and set light output on each flash The most fast flash sync speed is 1 320 s Setting 1 Mount the AK TTL TX on camera hotshoe 1 2 Connect AK TTL RX with flash by sync Cable Studio Flash ASC 2 sync cable for ASC 3 sync cable for studio hotshoe flash flash Make sure all TX and RX in the same Channel set on Channel switch Set the AK TTL s mode switch to M on both TX and RX Turn on flash and set the output manually Press test button on TX all flash with RX will blink Release the camera s shutter start shooting one AUTO mode Compatibility Completely compatible with Almost all brands and models of SLR cameras and flashes Connect a flash meter with AK TTL TX Connect the flash meter and AK TTL TX by ASC 2 Sync Cable to trigger and meter the flash www aokatec com Specifications Transmission System Communicating on 2 4 GHz radio frequencies 16 trans mission channels are available Transmission Range Approx 360ft 110 m Transmission Angle 360 all around Sync Speed High Speed Sync 1 8000 on AUTO model 1 320 on M model Power Source Two 1 5V AAA batteries Battery L
4. ife Approx 30 hours continuously Dimensions Approx 1 7 W x 2 7 H x 1 D 43 0 W x 68 5 H x 25 5 D mm Weight Approx 1 2 oz 37g excluding battery For Your Safety To prevent damage to the AK TTL and personal injury please read and observe the following important security precautions e Keep the unit and accessories out of reach of children e Keep the unit dry e Do not attempt to insert batteries upside down or backwards Do not mix old and new batteries or batteries of different types Do not disassemble the unit Do not expose to flame or excessive heat Keep out of reach of children Use only Promote approved accessories CE Compliance This device is in compliance with the essential reguirements and other relevant provisions of Directive 1999 5 EC ICC Compliance This Class B digital apparatus complies with Ca nadian ICES 003 FCC Compliance This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interfer ence and 2 this device must accept any interference re ceived including interference that may cause un desired operation www aokatec com Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B d
5. igital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Mounting and cable connections detailed in this document represent the intended usage however there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and the receiver 3 Consult the dealer or an experienced radio or television technician for help One Year Limited Warranty One year limited warranty Aokatec warrants this product against defect in materials and workmanship under normal use for period of one year from the date of retail purchase Support Support and maintenance for AK TTL is available at www aokatec com Support aokatec com
6. unit and additional ASC 1 sync cable sold separately e One transmitter TX can support 1 or multiple RX units and remote slave flashes e Same unit compatible with more flash systems Completely compatible with Nikon iTTL CLS Creative Lighting System Canon optical wireless E TTL flash system Pentax wireless P TTL flash system Olympus wireless flash system Sony wireless flash system Use SONY version TX ae RS AK TTL TX AK TTL TX AK TTL RX For Nikon Canon For SONY For Nikon Canon Pentax Pentax Olympus Olympus amp SONY www aokatec com Nomenclature Ou BU O ON CHANNEL Mode mark TX short for transmitter RX short for receiver States indicator Working green blink 4 seconds Trigger Test long red blink Low battery red blink 4 seconds Test button 16 Frequency channel switch Mounting foot Power and mode switch Provides a choice OFF or AUTO or M Manual Sync terminal 3 5mm Battery cover Strap hole Accessories Aokatec Sync cord ASC 1 AT O O AsC 2 EE EE RZ el ASC 3 o Mn ASC 1 Sync Cable 3 5mm male to IR sender For AK TTL AUTO mode ASC 2 Sync Cable 3 5mm male to PC male For AK TTL M mode ASC 3 Sync Cable 3 5mm male to 3 5mm male For AK TTL M mode www aokatec com Accessories AB N1 Hotshoe Bracket for AK TTL TX and IR Panel for Nikon Canon Pentax and other standard hotshoe cameras AB S1 Hotshoe
7. www aokatec com Aokatec WIRELESS TTL FLASH TRIGGER AK TTL AokateciEt 4 Aokatec 4 CHANNEL INSTRUCTION MANUAL www aokatec com Foreword Thank you for purchasing the Aokatec AK TTL Wireless TTL Flash Trigger To get the most out of your new AK TTL read this manual thoroughly before use Introduction The Aokatec AK TTL is a multi feature radio flash trigger system for wireless flash shoot ing Most of the original wireless flash system controlled by optical signals such as Nikon Canon Sony Pentax They are generally limited to line of sight operation and shorter ranges The AK TTL system convert optical signals to radio transmission it retain all functions of the original system achieves a transmission distance of up to 360ft 110 m all at a 360 degree angle With the extended more reliable range afforded by radio transmission ambitious photography is made easier The AK TTL also can work as a simple manual flash trigger Key features Reliable Wireless Full TTL 2 4G Radio transmission 110 meter 360 ft no direct line of sight needed High Speed Flash up to 1 8000 Ratio lighting control Trigger multiple flashes simultaneously Simple setup No programming required No new system to learn Set up as your original system Mix Radio and Optical system High Speed Flash for studio flash e One receiver RX can support 1 or more remote slave flashes Use stereo cable splitter from AK TTL Rx
Download Pdf Manuals
Related Search