GSM Alarm system user manual-
Contents
1. eg Press buttons of remote controller turn on PIR move the two parts of door detectors away then main panel receives the signal decodes the data and then saves them as the identified numbers into its memories this coding process finished user could make more detectors coding in turn about 25 seconds later coding status ended with one beep Attention Main panel will send two beeps Di Di when make one coding successfully meanwhile Zone ID LED would display its numbers accordingly 2 Adding code If user want to add more detectors codes and not remove the existed ones just press Code key for 2s to 3s release and then press again after one beep the system is in coding status the coding process is the same as above description after finishing coding Press Code key again the main panel ends coding process with one beep the previous codes still remained 3 Remove the code or re code Make the coding process according to above 1 process code what you want others would be lost automatically 4 Make alarm and answer 1 System startup and initialization Firstly connect the antenna input SIM card then plug in power supply the status LED lit if setup Arm status then Signal LED blinked when the system are searching network signal and initialization Signal LED lit when successful initialization extinguished if there is no signal or valid alarm phone Center numbers GSM Intelligent Alarm System user m2. format 1 XXX XXX XX XXXXXXXX Content of SMS Set main panel status the content of SMS includes ARM DISARM OUTPUT ON OUTPUT OFF RELAY ON RELAY OFF eg 1234ARM OUTPUT ON RELAY OFF Represents setting main panel Arm output on high relay on closed 2 Set new password to 6789 12344 PW 6789 3 Set main panel ID 0008 when need alarm center net work 1234 ID 0008 Figurel the main panel of the alarm system 4 Setting the number 13888888888 to A3 alarm telephone 1234 A3 1 38888888 3 Technical Parameters 5 Setting the message 1 external input alarm to SIM card 1234 SM 1 external input alarm 1 Power supply AC110V 220V DC12V 1A 2 Static Current lt 30mA 6 The LEDs on the main panel 3 GSM power CLASS4 2W EGSM850 900 1 Output indicator OUT lit when output high level extinguished when CLASSI 1W DCS1800 1900 output low level 4 Wireless frequency 433 92 or 315 if specified MHz 5 Wireless Modulation ASK GSM Intelligent Alarm System user manual 6 Wireless receive sensitivity 95dBm 12dB SINAD 7 Support wireless detectors 28 8 Volume of siren 110dBspl 9 Working Temperature 15C 455C R H lt 90 I The installation of the alarm system 1 Installation of main panel The main panel should be installed firmly wherever there is GSM signal and power supply no additional wired connection needed oo Figure2 the external
3. interface in the rear of main panel Backup battery optional switch the battery could keep the system work a few hours without external power supply External power supply socket DC 12V 1A inner Anode External 12 pins interface see Note 3 SIM card eject the tray by pressing the yellow button push it back after putting the card into the tray CODE pressing key code register for main panel and wireless detectors RESET pressing key keep pressing the key when power on to initialize all the parameter to factory settings MOU Antenna Port connect antenna before operation keep the antenna is in vertical for better performance Note 3 External 12 pins interface from left to right Pin 1 Common ground GSM Intelligent Alarm System user manual 2 Alarm Activated The following way could activate the alarm of main panel When the main panel is in arm status any level change more than 100ms in the wired input terminal I1 to I7 pressing panic button of remote controller pressing button of panic button alarm signal from PIR door detector gas detector smoke detector etc 3 Valid answer release alarm When one alarm activated the siren rings main panel sends alarm message followed by dialing alarm phone number dialing alarm center number at first if alarm center is supported continuously up to 5 times if there is no valid answer or release action If user answer the alarm phone after enteri
4. panic buttons and so on 8 Indicates up to 30 Activated Zone numbers display zone numbers when the sensors make alarm and coding 9 Sets the system status Arm Disarm etc by a telephone or SMS 10 Makes arm disarm or panic through remote controllers 11 Four digits password is used for remote access for security reasons 12 Onsite voice Monitoring through telephone from long distance 13 Have one onsite high volume siren send sound when alarm occurs 14 One onboard relay available for customer application 15 One open collector output available to be used according to customer demands 2 3 4 5 6 Relay status led RELAY Siren status led SIREN GSM Intelligent Alarm System user manual Input indicator INPUT lit when any of input from IN1 to IN7 activated extinguished for no status change Relay indicator RELAY lit when inside relay closed and extinguished when opened Siren indicator SIREN lit when siren is ringing extinguished while not ringing Monitor indicator MONITOR lit when get into onsite monitor status and extinguished without monitoring GSM signal indicator SIGNAL blinked when searching GSM signal and alarm phone numbers dialing and connecting lit in standby extinguished if there are no signal or valid alarm phone numbers Output led OUT Input led IN Power supply led POWER Arm disarm status STATUS GSM card status SIGNAL Monitor status MONITOR Fi
5. GSM Intelligent Alarm System Installation and User Manual GSM Intelligent Alarm System user manual 3 Wireless Remote Controller DC 12V 8 4V Power supply Static Current Tran smission Current Transmission Frequency Transmission Time Transmission Distance Working Condition Relative Humidity ll 0 I2 lt 15mA f 3 15 433 92 4 T lt is lt 90 0 2MHZz No Obstacle 80m Temperature 10C 40 V Frequency Questions amp Answers Problems Main panel can t dial when alarming Fail to set alarm number or message by SMS Can t setup or control from long distance Can t work if remove DC power External wired detectors work Probable Reasons 1 No GSM antenna mounted 2 Invalid SIM Card or short of fee 3 Alarm or center number are incorrect 4 Misuse detectors or not make valid coding 1 The format is incorrect 2 Password is invalid 1 Wrong password or no corresponding actions 2 Too fast key pressing result from unstable detection 1 No backup battery available 2 Backup battery switch turns off 1 The connection between the panel and detector is incorrect 2 Misunderstanding Low Solutions 1 Mount the antenna correctly 2 Make sure SIM card in the working condition 3 Set phone numbers correctly 4 Install and use the detectors according to user manual 1 Set the numbers followed by user manual 2 Use initial password after res
6. Relative Humidity DC 12V 8 4V inner battery DC 1 2V Il lt 15pA 2 lt 15mA f 315 433 92 0 2MHz T 1S No Obstacle 80m 15mm 10C 40T lt 90 DC 9V 7 2V inner battery DC 9 V Il lt 30A I2 lt 20mA f 433 92 or 315 40 2MHz T gt ls No Obstacle 80m lt 2min 30s lt 35s 5 15m Horizontal 110 Vertical 60 Temperature 10 C 40 lt 90 GSM Intelligent Alarm System user manual Table Of Content OVVIE We enea a S I AAA I The installation of the alarm system 1 Installation OF mait Panel sss ics sccciesaccise sued exenceecevssinaensdeneed coneeencae dusvessedevend cate cso 2 Installation Of door detector sesnes se sscecsssecessecces sn sessseceeseecesee cessseeesssceneaee s 3 Installation Of PLR essshceiecsericdiesdscdesncsicsiascrtevctsssdvamustarsdsvenseutemascaadarariceeians Il The usage of main panel 1 Setting Alarm phone number 2 Setting alatm MESSAGE csc occwdsessstewnsesdesnsscsovenqateseyueseveesosonseictdcvecbesuestoeanaceness 3 Coding between main panel and wireless detectors 0 ceeeeee eee 4 Make alarm and answet cccccccssccesscecsssecesscee cosscessseeseeeee sn secessseesesseeeus seeeaes 5 Setting function Of main panel i ccssseesesecsossedvesdecscetsevesssoodsedusdencstosdeveesevaseyeds 6 The LEDs on the tain pame ls sccssscsecstsssussnsescpesenseyecsese tau ebshessesevsvyen nE Ill Usage of wir
7. anual Pin 2 Siren output positive negative is connected to common ground Pin 3 Output terminal composed with common ground Pin 4 to Pin 10 are wired input terminals each composed with common ground Self adapt alarm activated that is more than 100ms level change in the working situation would activate the alarm Pin 11 and Pin 12 are the input and output terminals of onboard relay Closed when Relay is on and open when off Sen ott Dl all Dl DI Pall DI Dl 220V O P device Wired sensor7 Lamp han Figure 3 the Geren of how to connect external ports 2 Installation of door detector From the principle of Magnetic Door Window detector When the gap of magnet and Magnetron is increased to a certain distance the magnetism decreases accordingly and the switch in the Magnetron turns on and result from alarming It can detect the opening of doors and windows Magnet part is easy to install on doors or windows the other part then fixed on the door frames by adhesive tape the activated gap is about 15mm 3 Installation of P LR PIR could detect body in the certain range Detection distance is from 5 to 15 meters adjustable Horizontal detection angle is 110 degrees and vertical detection angle is 60 degrees Adjust the direction and distance to the suitable GSM Intelligent Alarm System user manual position and
8. eless remote controller oo cece ceeceetsessese se aeeneee IV Technical parameters for wireless detectors essen cceeeeeeeeeeneeeceaeceeeeates V Frequency Questions amp ANSWEYTS 1 cecessesecesessees ceseseeenecesecaee cess ceseeeeeaeenees 4 GSM Intelligent Alarm System user manual Overview Thanks for selecting the GSM alarm system please read the user manual carefully before installation and operation GSM intelligent alarm system has all the function of traditional telephone alarm system moreover it takes the advantage of GSM network and short text message it would be used more convenient reliable and efficient 1 Fundamental function of the system 1 Support multi GSM bands This panel suits for L GSM900 DCS1800 MHz L GSM900 DCS1800 1900 MHz GSM850 900 DCS18 00 1900 MHz 2 The main panel has the option which supports Alarm center please check when selecting this panel Does not support alarm center O Supports Ademco Contact ID format alarm center O Supports other format alarm center 3 No need of fixed telephone line It is very suitable for cottage house shop garage wherever GSM Network is present 4 Sends preset messages to the mobile phone whenever alarm is activated 5 Easy to setup alarm phone numbers and sending messages through SMS 6 Supports up to 7 wired sensors 7 Main panel supports all kinds of wireless detectors PIR infrared balusters smoke sensors gas sensors
9. et 1 Input the right password receiving Di tone when make the correct action 2 Pressing the key firmly 1 Use backup battery optional 2 turn the switch on 1 Make the connection correctly according to the manual 2 Confirm to use the suitable GSM Intelligent Alarm System user manual The remote controller has three buttons or four buttons Arm Button At home arm button 1 Disarm Button Panic Button O gt press Arm Button status LED on the panel blinks about 25s then armed delay arm Press arm followed by panic button immediately would get into arm status at once instant arm At home arm button has the same operation or When as arm button except only specified at home armed detectors could activate the alarm Pressing Panic button would activate the alarm and Disarm button would release and cancel the alarm at any time IV Technical parameters for wireless detectors 1 Wireless gap door window Detector Power supply Static Current Transmission Current Transmission Frequency Transmission Time Transmission Distance Internal distance Working Temperature Relative Humidity 2 Wireless P I R Detector Power supply Static Current Transmission Current Transmission Frequency Transmission Time Transmission Distance Preheating Time Interval of twice Emission Detected Distance Detected Angle Working Condition
10. gure 4 the LEDs in the front panel 7 Status indicator STATUS lit when armed extinguished for disarmed blinked for alarming and delay arm 8 Power indicator POWER lit when power on 9 Zone indicator ZONE ID 8 LEDs on the top right corner of panel represents the zone numbers display 1 9 and A F digit 1 7 represent external wired input zone I1 to I7 8 F represents wireless zone 8 15 1 F with the lit oo point represents wireless zone 1 6 30 II Usage of wireless remote controller GSM Intelligent Alarm System user manual GSM Intelligent Alarm System user manual 6 Release alarm main panel ends alarming and connection 2 Basic kits configuration TH Siren rings when alarm is activated default 7 No ring when alarm activated Main panel with antenna 1 set BH RH Change to new password Power supply Ipe 9 Disable onsite monitoring default Wireless P LR 1pc ga Enable onsite monitoring Wireless Door detector 1 set Attention Remote controller 2 pes Each operation is ended with or one beep indicates one successful action External siren Ipe no beep indicates the action is invalid please check and try again User manual Ipe Optional backup battery wireless smoke detector wireless gas Method 2 Setting by SMS detector wireless infrared curtain sensor panic button etc Sendin g SMS to main panel number through cell phone with the following
11. ireless door detector alarm the message would be sent when zone 8 is activated Method 2 Sending SMS to main panel number by the following format x SM 2 35 XXXXXXXXXX For example 1234 SM 5 external input is alarming Then the message S external input alarm is alarming would save to SIM card as the alarm message Note 1 The digits 1 35 in the head of each message is the must otherwise they would not be corresponded to wired and wireless alarm zone numbers The length of each message is not more than 100 letters exceeded parts would be probably missed 2 All messages are saved into SIM card the panel would only deal with message to 18 if the messages capability of the card is 20 6
12. ng the valid password pressing 6 would release this alarm also user could press disarm button of the remote controller to cancel the alarm otherwise the main panel would not stop alarm until five rounds dialing 5 Setting function of main panel Method 1 Remote control by telephone When user dial the main panel connection established about 10 seconds then enter password and the default password is 1234 by pressing the keys of the talking phone after one beep user could make the following function configuration through pressing the keys O Arm default 0 Disarm 1 Output high 1 Output low default 2 Report the status when make arn disarm to alarm center Enable for panels support alarm center 2 Report the status to alarm center Disable default Sit FERE H Set ID of main panels for panels support alarm center 4 Relay closed 4 Relay opened default 5 Send SMS when alarm activated default 5 Do not send SMS when alarm activated 8 GSM Intelligent Alarm System user manual 3 Coding between main panel and wireless detectors All wireless detectors had been registered coded to the main panel from the factory But it is absolutely necessary to clear the coding process 1 Coding during the specified time Keep pressing Code key for about 4s to 5s until one beep then release the key the system is in coding status Make the wireless detectors work and send signal
13. s valid 8 digits phone number two besides A1 A7 isthe must which is the particular format XX XXX XXX XX represents text characters For example 1234 A 1 88888 888 Setting the number 88888888 to Al alarm phone No 1 GSM Intelligent Alarm System user manual 2 Setting alarm message The alarm message is the corresponding text information SMS sent to user mobile phones which preserved in the main panel when this zone alarm is activated those messages are created by the main panel by the default format 1 2 35 zone activated in the initialization process Messages 1 to 7 are corresponding to wired input to 7 when wired input 1 activated message would be sent to alarm phone numbers Messages 8 to 35 are corresponding to the wireless alarm detectors which registered with the main panel such as PIR smoke detector gas detector and so on When there is one alarm activated eg Zone 8 then the message 8 in the SIM card would be sent to the alarm phone numbers Also user could change the content of messages according to the detail requirement through the following method Method 1 Put the SIM card into one GSM cell phone if the card is initialized by the main panel there should be those messages in the card user just edit the corresponding text to require content Also user could add the SMS into the SIM card by the following format 1 2 35 XXXXXXXXX the text content For example edit the message 8 w
14. then fix the PIR on the wall or the furniture Please be noted the position and direction of the PIR would affect the detection performance please contact your suppliers if you meet difficulties when make the installation II The usage of main panel 1 Setting alarm telephone numbers Before use this panel you must set alarm phone or alarm center numbers up to 7 alarm phone number could be set in SIM card by the user name A1 to A7 when alarms activated main panel would dial the alarm numbers Al to A7 in tum meanwhile send alarm messages to the alarm phone numbers Method 1 for setting the alarm numbers Put the SIM card into one GSM cell phone and save alarm phone numbers in SIM card by the name A1 to A7 respectively No longer than 20 digits for each number no needed for international numbers no country code for domestic numbers Please pay attention If the main panel support alarm center then A1 A2 would be saved to Alarm center phone number and A3 A7 would represent Alarm phone No 1 to 5 when alarm activated the main panel would dial Alarm Center number A1 A2 at first then dial alarm phone number A3 A7 in turn Method 2 Sending short message to main panel number through cell phone with the format HA 1 A2 A3 A4 A5 A6 A 7 H HHEHHHH In this manual if there is no particular declaration KE represents 4 digits password default is 1234 Al to A7 represent alarm phone No HHHH represent
Download Pdf Manuals
Related Search