20AE51-00 E4 User Manual
Contents
1. 4 pin USB Type A plug according to Universal Serial Bus Specification Revi sion 1 0 Table 7 Pin assignment of USB front panel connectors 1 45V 5 2 USB D 3 USB D 4 GND 5 V power supply USB negative USB positive Digital ground MEN Mikro Elektronik GmbH 20AE51 00 E3 2011 12 23 Onboard Connectors 3 6 Ethernet Interface For detailed information regarding the Ethernet controllers MAC address etc please consult the SBC board manual This manual only deals with the physical Ethernet connectors on the AE51 Connector type 8 pin M12 receptacle female A coded 90 Phoenix Contact 1436974 SACC DSIV FS 8CON L90 SCO Mating connector e 8 pin M12 plug male A coded Table 8 Pin assignment of Ethernet front panel connectors 1000Base T 10 100Base T 1 BI DC 2 BI DD 3 BI DD 2 4 BI DA TX 8 5 BI DB RX a 6 BI_DA TX 7 BI_DC 8 BI_DB RX Table 9 Signal mnemonics of Ethernet front panel connectors Signal Direction Function BI Dx in out Differential pairs of data lines for 1000Base T RX in Differential pair of receive data lines for 10 100Base T TX out Differential pair of transmit data lines for 10 100Base T 3 6 1 Ethernet Status LEDs The AES1 provides a total of four Ethernet status LEDs two for each Ethernet channel They signal the link and activity status different LED behavior can be realized o2. 10 pin low profile header with lock 2 54 mm pitch for ribbon cable connection Mating connector 10 pin IDC receptacles e g Elco Series 8290 IDC socket Table 12 Pin assignment of the HD audio onboard connector 1 AUDIO OUT L 2 AUDIO GND 1 i 2 3 AUDIO OUT R 4 AUDIO INL E E 5 AUDIO SPDIF 6 AUDIO OUT L 9 lt 10 7 AUDIO OUT R 8 AUDIO GND 9 AUDIO IN R 10 not connected Table 13 Pin assignment of the optional HD audio D Sub front connector 9 AUDIO IN R 5 AUDIO SPDIF 9 es 5 8 AUDIO_GND 4 AUDIO IN L Se 7 AUDIO OUT R 3 AUDIO OUT R 98 1 6 AUDIO OUT L 2 AUDIO GND 1 AUDIO OUT L Table 14 Signal mnemonics of the HD audio interface Signal Direction Description AUDIO OUT Lz Rx out Line out left and right differential signal pairs AUDIO IN L R in Line in left and right AUDIO GND Analog ground AUDIO SPDIF out S PDIF output 3 9 Serial Interfaces via SA Adapter optional As an option the board offers the possibility to provide two serial interfaces at the connector PCB using a MEN standard SA Adapter This way a serial interface can be used which can be flexibly configured as needed SA Adapter slot 1 available at the X3 front connector can be used for UART or CAN bus while slot 2 X4 can be used for UART IBIS or GPS functionality Please consult the respective SA Adapter user manual for installation instructions TA See MEN s website for a list of S
3. interface but in turn it enables features like an USB driven touch interface via the DisplayPort connector USB instead of AUX can also be made avail able on the DP1 connector as an option Connector type 20 pin DisplayPort receptacle Mating connector 20 pin DisplayPort plug Table 5 Pin assignment of 20 pin DisplayPort connector 20 POWER 19 RETURN PWR 18 DPx HOTPLUG 17 bic OR a i GNP b DUREE 14 CONFIG2 13 CONFIG1 12 LANE 3 11 GND 10 LANE 3 9 LANE 2 8 GND 7 LANE 24 6 LANE 1 5 GND 4 LANE 14 3 LANE 0 2 GND 1 LANE 0 Table 6 Signal mnemonics of 20 pin DisplayPort connector Signal Direction Function GND Ground POWER out Power for connector 3 3 V 500 mA RETURN PWR Return for Power DPx HOTPLUG in Hot Plug Detect DPx AUX DPx AUX in out Bi directional half duplex auxiliary channels for device management and device control Note As an option these lines can be used for a USB interface as realized for DisplayPort C on the SC24 SBC board MEN Mikro Elektronik GmbH 18 20AE51 00 E3 2011 12 23 Onboard Connectors Signal Direction Function DPx USB n p in out USB negative positive CONFIG1 CONFIG2 Connected to Ground LANE_ 3 0 LANE_ 3 0 out Main Link data lanes 3 5 USB Interface Connector type 4 pin USB Type A receptacle according to Universal Serial Bus Specification Revision 1 0 Mating connector
4. 0 SMB CLK 27 GND 28 1 5V 25 PERpO 26 GND 23 PERnO 24 3 3Vaux 21 GND 22 PERST 19 Reserved 20 W_DISABLE 17 Reserved 18 GND Mechanical Key 15 GND 13 REFCLK 14 UIM_RST 11 REFCLK 12 UIM CLK 9 GND 10 UIM DATA 7 CLKREQ 8 UIM_PWR 5 Reserved 6 1 5V MEN Mikro Elektronik GmbH 0000000000000 23 20AE51 00 E3 2011 12 23 Onboard Connectors Pin Signal Pin Signal 3 Reserved 4 GND 1 WAKE 2 3 3Vaux MEN Mikro Elektronik GmbH 24 20AE51 00 E3 2011 12 23 Onboard Connectors Table 16 Signal mnemonics of 52 pin PCI Express Mini Card connector Signal Direction Function Power GND Ground 3 3Vaux out 3 3V source 1 5V out 1 5V source SIM card UIM PWR in SIM card power UIM DATA in out SIM card data UIM CLK in SIM card clock UIM RST in SIM card reset PCI REFCLK REF out PCI Express differential reference Express CLK clock PERnO PERpO in PCI Express receive signals PETnO PETpO out PCI Express transmit signals Auxiliary CLKREQ in Clock request Signals PERST out Reset for the Mini Card W_DISABLE out Wireless disable WAKE in Wake signal SMB_CLK out System management bus clock SMB_DATA in out System management bus data USB USB_D in out USB line USB_D in out USB line Please refer to the PCI Express Mini Card Specification for further details See Chapter 5 1 Literature and Web Resources on page 28 MEN M
5. 20AE51 00 E3 2011 12 23 AEST Graphics and I O Interface for Display Computers Configuration example User Manual men mikro elektronik gmbh n rnberg AE51 Graphics and I O Interface for Display Computers AE51 Graphics and I O Interface for Display Computers The AE51 is a combined graphics and I O interface board for MEN s display computer electronics like the SC24 SBC and possible subsequent models Three rugged AirMax VS connectors transport the various I O signals from the SBC board to the AE51 where they are made available on standard connectors like USB 9 pin D Sub serial I O and HD audio both optional 8 pin M12 Gigabit Ethernet DisplayPort amp and SATA Touch functionality can be realized via the USB port Note that the AE51 is just one suggested interface board variant for SBCs like the SC24 and as such it does not necessarily cover all possible interfaces of the connected SBC board For example only two independent DisplayPort interfaces B and C with their individual AUX and USB channel respectively are made available on standard DP connectors whereas an SC24 offers two additional DisplayPort 9 interfaces identical to the former two regarding image content The AES51 serves as a 2x PCI Express Mini Card carrier for the connected SBC board Two SIM card slots are available By default one is used for each of the two PCI Express Mini Cards but the first PCI Express Mini C
6. 7 MEN Mikro Elektronik GmbH 12 20AE51 00 E3 2011 12 23 Getting Started 1 Getting Started This chapter gives an overview of the board and some hints for first installation in a system 1 1 Map of the Board Figure 1 Map of the board top view AirMax VS AirMax VS board to board board to board connectors connector V puey IUIN SSaJdX3 Od g ped lull SSaJdX3 Od peer ul BONN Erde dee d Power bypass connector optional 00000 00000 HD Audio to optional front PeedrpyoeCc9Mhemer Gscid yg UART IBIS UART or CAN bus Power Input 2x DisplayPort USB 2x Gigabit Ethernet MEN Mikro Elektronik GmbH 20AE51 00 E3 2011 12 23 Getting Started Figure 2 Map of the board front connectors shown behind possible front panel m 1 ETH1 ETH2 Q oS mE mE COHEN A X3 AUDIO SE efx O 6 All optional connectors shown Top level left to right PCI Express Mini Card B SMA antenna connectors Ethernet port 1 status LEDs Ethernet port 1 Ethernet port 2 Ethernet port 2 status LEDs USB DisplayPort 1 DisplayPort 2 general status LEDs power input Bottom level left to right Serial interface 1 UART or CAN bus serial interface 2 UART or IBIS or GPS HD audio PCI Express Mini Card A SMA antenna connectors 1 2 Installing the Adapter in a System The AE51 was designed as a joint graphics and I O connector board for MEN s display computer electronics like the SC24 The connecti
7. A Adapters which can be used on the AE51 Please contact MEN s sales team for information about possible configurations and special board versions MEN Mikro Elektronik GmbH 22 20AE51 00 E3 2011 12 23 Onboard Connectors 3 10 The AE51 supports the PCI Express Mini Card standard As an option it can also be equipped with PCI Express Mini Card slots compatible with half size modules PCI Express Mini Card Interface PCI Express Mini Cards are small form factor PCI Express cards The main differences between an ExpressCard and a PCI Express Mini Card is a smaller form factor optimized for mobile computing platforms and a card system Interconnection optimized for communication applications PCI Express Mini Cards also use smaller connectors than standard ExpressCards The cards use either a single PCI Express lane x1 or a USB connection the AES1 supports both It is equipped with two 52 pin standard PCI Express Mini Card connectors The following standard signals are supported signal directions according to PCI Express Mini Card standard Table 15 Pin assignment of 52 pin PCI Express Mini Card connector Pin Signal Pin Signal 51 Reserved 52 3 3Vaux 49 Reserved 50 GND 47 Reserved 48 1 5V 45 Reserved 43 GND 41 3 3Vaux 39 3 3Vaux 40 GND 37 GND 38 USB D 35 GND 36 USB D 33 PETpO 34 GND 31 PETnO 32 SMB DATA 29 GND 3
8. WIMAX GSM GPRS UMTS 2 SIM card slots PCI Express and USB interface Accelerometer Magnetometer 3 acceleration channels 2independent programmable interrupt generators for free fall and motion detection 3 magnetic field channels 1 3 to 8 1 gauss magnetic field full scale Miscellaneous Gold Cap to buffer real time clock on connected SBC board MEN Mikro Elektronik GmbH 3 20AE51 00 E3 2011 12 23 Technical Data Electrical Specifications Isolation voltage Ethernet ports 1 500 VDC DC DC 1 500 VDC Supply voltage 24 VDC nom 9 to 36 V EN 50155 power interruption class S2 Power output 12 VDC nom Power consumption Up to 30 W Mechanical Specifications Dimensions approx 170 mm x 132 mm x 30 mm Weight approx 100 g Environmental Specifications Temperature range operation 0 460 C up to 40 85 C screened Fanless operation e Temperature range storage 40 85 C Relative humidity operation max 95 non condensing Relative humidity storage max 9596 non condensing Altitude 300 m to 3 000 m Shock 50 m s 30 ms Vibration function 1 m s 5 Hz 150 Hz Vibration lifetime 7 9 m s 5 Hz 150 Hz Conformal coating on request MTBF tbd 40 C according to IEC TR 62380 RDF 2000 EMC Conforming to EN 55022 radio disturbance IEC 61000 4 2 ESD and IEC 61000 4 4 burst e Prepared for certification according to el requi
9. al numbers listings C function descriptions or wherever appropriate Hexadecimal numbers are preceded by Ox hyperlink Hyperlinks are printed in blue color The globe will show you where hyperlinks lead directly to the Internet so you can look for the latest information online IRQ Signal names followed by ff or preceded by a slash indicate that this signal is IRQ either active low or that it becomes active at a falling edge in out Signal directions in signal mnemonics tables generally refer to the corresponding board or component in meaning to the board or component out meaning coming from it Vertical lines on the outer margin signal technical changes to the previous issue of the document MEN Mikro Elektronik GmbH 9 20AE51 00 E3 2011 12 23 About this Document Legal Information MEN Mikro Elektronik reserves the right to make changes without further notice to any products herein MEN makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does MEN assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters can and do vary in different applications All operating parameters including Typicals must be validated for each customer application by customer s technical experts MEN does no
10. ard can also switch between the two SIM cards as an option The necessary antenna connectors can be led to a front panel As an option a SATA interface from the SBC board can be made available along with a 4 pin power connector for the drive however the AE51 is not designed as a SATA HDD SSD carrier board the drive must be mounted independently The board also serves as a 30W 24 VDC nom 9 to 36 V class S2 wide range power supply for the connected SBC board If the connected display panels require more power an external PSU can be connected via an optional power bypass connector on the AE51 to supply the necessary 12 VDC voltage for the system MEN Mikro Elektronik GmbH 2 20AE51 00 E3 2011 12 23 Technical Data Technical Data Board to board connection 3 AirMax VS connectors To SBC board s graphics and I O connectors P1 P2 P4 I O 2 DisplayPort interfaces DisplayPort 1 with AUX channel and hot plug detection DisplayPort 2 with USB channel HD audio HD audio codec Realtek ALC268 Audio stereo in Audio stereo out SPDIF out Via 10 pin onboard connector 2 Gigabit Ethernet Via MI2 connectors USB 2 0 Via Type A connector e 2 SA Adapter slots for serial I O 1 UART or IBIS GPS 1 UART or CAN bus 8 status LEDs 4 for Ethernet link and activity status 2 for general board status 2 for power supply status 2 PCI Express Mini Card slots For functions like WIFI
11. are trademarks of MEN Mikro Elektronik GmbH PC MIP is a registered trademark of MEN Micro Inc and SBS Technologies Inc MEN Mikro Elektronik ESMexpress MIPIOS and the MEN logo are registered trademarks of MEN Mikro Elektronik GmbH AirMax VS is a registered trademark of FCI Altera Arria Avalon Cyclone Nios and Quartus are registered trademarks of Altera Corp InsydeH2O is a trademark of Insyde Software Corp microSD is a trademark of SD 3C LLC Microsoft and Windows are registered trademarks of Microsoft Corp Windows Vista is a trademark of Microsoft Corp PCI Express and PCIe are registered trademarks of PCI SIG All other products or services mentioned in this publication are identified by the trademarks service marks or product names as designated by the companies who market those products The trademarks and registered trademarks are held by the companies producing them Inquiries concerning such trademarks should be made directly to those companies All other brand or product names are trademarks or registered trademarks of their respective holders Information in this document has been carefully checked and is believed to be accurate as of the date of publication however no responsibility is assumed for inaccuracies MEN Mikro Elektronik accepts no liability for consequential or incidental damages arising from the use of its products and reserves the right to make changes on the products herein wit
12. c Discharge ESD Computer boards and components contain electrostatic sensitive devices Electrostatic discharge ESD can damage components To protect the board and other components against damage from static electricity you should follow some precautions whenever you work on your computer Power down and unplug your computer system when working on the inside Hold components by the edges and try not to touch the IC chips leads or cir cuitry Use a grounded wrist strap before handling computer components Place components on a grounded antistatic pad or on the bag that came with the component whenever the components are separated from the system Store the board only in its original ESD protected packaging Retain the original packaging in case you need to return the board to MEN for repair MEN Mikro Elektronik GmbH 7 20AE51 00 E3 2011 12 23 About this Document About this Document AN This user manual describes the hardware functions of the board connection of peripheral devices and integration into a system It also provides additional information for special applications and configurations of the board The manual does not include detailed information on individual components data sheets etc A list of literature is given in the appendix History Issue Comments Date E1 First issue 2011 09 15 E2 Added cover photo product weight DC DC isola 2011 11 03 tion voltage Standard model comes without a front pa
13. e power consumption of the system should exceed the 30 W limit of the AE5S1 s integrated power supply e g when the system is also used to power a large display panel the board s internal DC DC converter can be bypassed For this purpose the board can be equipped with the optional power bypass connector to enable the connection of a more powerful external PSU supplying the connected SBC board with the necessary input voltage of 12 VDC Connector type 4 pin COMBICON receptacle Phoenix Contact 1755752 MSTBVA 2 5 4 G 5 08 Mating connector 4 pin COMBICON plug e g Phoenix Contact 1786420 IC 2 5 4 G 5 08 Table 2 Pin assignment of optional power bypass connector 4 VCC FLYBACK Power to additional DC DC m converter output 2 IGND Isolated power input ground B 3 12V FLYBACK OUT 12V from external DC DC converter 4 GND GND MEN Mikro Elektronik GmbH 16 20AE51 00 E3 2011 12 23 Onboard Connectors 3 3 Mass Storage 3 3 1 Serial ATA SATA optional As an option the AE51 can provide one serial ATA SATA interface controlled by the connected CPU board It is available via a standard 7 pin SATA connector You can connect a hard disk or solid state drive Please note that the AE51 is not designed as a carrier board for such drives any drives have to be installed externally Power for the drive is supplied via a 2 5mm 4 pin header Please refer to Figure 1 Map of the board top view on
14. faces zi uus 5ao 0 gah Chand re cee GO 18 23 USB IMierace 2 sass 56th eh ata E HOO t Oa RETO Ree 19 5 6 Ethernet IntetTa6e ass sumed odo o t eoa lv dash ceeds 20 3 6 1 Ethernet Status LEDS sue RR RD RE PR ERRP EA 20 3 7 General Staus EIS ceu decim do EL EE E bs 2 3 8 HD Audio ixeeseckeBecsar ae ieee babs SR E WE RO VERE EY 22 3 9 Serial Interfaces via SA Adapter optional 22 3 10 PCI Express Mini Card Interac uii mee ea 23 23 10 1 SIM Card Slos o miro sees ee S 9 ka n aei Aois 26 4 Organization of the Board eeeeeeeeeeeennnnn 27 4l SMBUS DEVICES cas oe ra ekskl 27 5 App pendis esee necs nenne pee Web ueesss eed eee TEES 28 5 1 Literature and Web IResoUtGes csus soo eot tint PDC ER Pd ee 28 5 11 POLEBxpress Mini Catd soe ne Re Re 28 5 1 2 Accelerometer Magnetometer STTS424E02 28 5 1 3 Temperature Sensor EEPROM LSM303DLH 28 5 2 Finding out the Product s Article Number Revision and Serial Numbet sseoesse ee 28 MEN Mikro Elektronik GmbH 11 20AE51 00 E3 2011 12 23 Figures Fisure l Map ot the board top Vie Wiec sus vate we phe eR wats 13 Figure 2 Map of the board front connectors shown behind possible front panel 5 2 20 sket Beda teias 14 Figure 3 Connecting an AE51 and an SBC board via the AirMax VS Connectors A von srt DEDE DRAG 14 Figure 4 General status LEDs on a possible front panel shown partially 21 Figure 5 SIM card swi
15. hout notice to improve reliability function or design MEN Mikro Elektronik does not assume any liability arising out of the application or use of the products described in this document Copyright 2011 MEN Mikro Elektronik GmbH All rights reserved eS Please recycle Germany France USA MEN Mikro Elektronik GmbH MEN Mikro Elektronik SA MEN Micro Inc Neuwieder Stra e 5 7 18 rue Ren Cassin 24 North Main Street 90411 Nuremberg ZA de la Ch telaine Ambler PA 19002 Phone 49 911 99 33 5 0 74240 Gaillard Phone 215 542 9575 Fax 49 911 99 33 5 901 E mail info men de www men de Phone 33 0 450 955 312 Fax 33 0 450 955 211 E mail info men france fr www men france fr Fax 215 542 9577 E mail sales menmicro com www menmicro com MEN Mikro Elektronik GmbH 10 20AE51 00 E3 2011 12 23 Contents Contents 1 Getting Started osos Sexe y e e Yom ie eoe RR D Ru dee 13 LE Mapot the Board 5 uai duo qo og opto oido incu 13 1 2 Installing the Adapter ina System esee eese 14 2 Interface to CPU Board eos esos bese ka kioES eee aranes 15 3 JOnboard Connectors Loss ades E med qUE KP REPRE RC RE REPRE CREBRO E 16 3 1 Power Supply COnnector i ass eene beg ero ces Ehren 16 35 2 Power Bypass Connector optional cese er Rhe m e 16 3 3 JM SS StOFABe ii ccadnas cde thas CAG dey esas ER FRA Bee META E 17 3 3 1 Serial ATA SATA optional 0 000002 eee eee 17 34 DisplayPort Inter
16. ikro Elektronik GmbH 20AE51 00 E3 2011 12 23 3 10 1 SIMB SW SIM Card Slots The AES51 offers two SIM card slots for the two PCI Express Mini Card slots The default setting has Mini Card A connected to SIM card A and Mini Card B to SIM card B However both SIM card slots can be connected to PCI Express Mini Card A if needed The necessary switching is performed by software via the SIMA SW and lines Figure 5 SIM card switching option SIM CardB C SIM ard A PCI Express Mini Card A PCI Express Mini Card B Table 17 SIM card switching option Onboard Connectors Te M cards RS MI ard 0 0 SIM card A SIM card B 0 1 SIM card A 1 0 SIM card B 1 1 SIM card B MEN Mikro Elektronik GmbH 20AE51 00 E3 2011 12 23 Organization of the Board 4 Organization of the Board 4 1 SMBus Devices The AE51 adds three additional SMBus devices to the system it is connected to Table 18 SMBus devices 12C Bus Address Function 0 0x30 write LSM303DLH accelerometer 0x31 read 0 0x3C write LSMSOSDLH magnetometer 0x3D read 1 OxAC STTS424E02 temperature sensor and production data EEPROM MEN Mikro Elektronik GmbH 27 20AE51 00 E3 2011 12 23 Appendix 5 Appendix 5 1 Literature and Web Resources e AESI data sheet with up to date information and documentation www men de products 08A E51 html 5 1 1 PCI Express Mi
17. n demand Table 10 Ethernet status LED LED Description LED Description e Port 1 activity 3 Port 2 activity 2 Port1 link 4 amp Port 2 link MEN Mikro Elektronik GmbH 20 20AE51 00 E3 2011 12 23 Onboard Connectors 3 7 General Status LEDs In addition to the four Ethernet status LEDs the AE51 provides four general status LEDs Two of them signal whether input power is applied and whether the output power to the SBC board as generated by the AE51 s onboard DC DC converter is within valid range The status LED is connected to the system s board management controller Please refer to the manual for the connected SBC board for information on its behaviour The user LED A is connected to an SGPIO line and can be used freely depending on an application s requirements Figure 4 General status LEDs on a possible front panel shown partially s Table 11 General status LEDs as depicted above LED Description LED Description 5 Output power12VOK 7 Status 6 Input power applied 8 UserLEDA MEN Mikro Elektronik GmbH 21 20AE51 00 E3 2011 12 23 Onboard Connectors 3 8 HD Audio The AE51 supports a high definition audio interface implemented via the Realtek ALC268 codec It is available on a 10 pin onboard connector and can be led to a standard 9 pin D Sub front connector via an optional ribbon cable adapter Connector types
18. nel some drawings still depict a possible front panel for clarity Configuration options Added SATA power bypass connector USB instead of AUX for DisplayPort 1 HD audio is a standard feature via onboard con nector D Sub adapter for front panel optional Updated block diagram with the above changes Clarified position and individual functionality of the two optional serial interfaces Added pinout for HD audio onboard connector Changed order of DisplayPort pinout mnemonics table Added product page links for temperature sensor EEPROM and accelerometer magnetometer Minor changes cosmetics E3 Removed pin assignment of board to board con 2011 12 09 nector to be included in manuals for SBC boards reworked phrasing regarding DisplayPort connector pin assignment and USB via AUX option on SC24 Manual now less focused on a specific SBC board Reworked PCI Express Mini Card connector pin assignment table signal directions now given from SBC perspective E4 Added Gold Cap to technical data 2011 12 23 Conventions This sign marks important notes or warnings concerning proper functionality of the product described in this document You should read them in any case MEN Mikro Elektronik GmbH 8 20AE51 00 E3 2011 12 23 About this Document italics Folder file and function names are printed in italics bold Bold type is used for emphasis monospace A monospaced font type is used for hexadecim
19. ni Card PCI Express Mini Card Electromechanical Specification Revision 1 2 October 26 2007 PCI Special Interest Group www pcisig com 5 1 2 Accelerometer Magnetometer STTS424E02 e Manufacturer s product page for STTSA24E02 Memory module temperature sensor with a 2 Kb SPD EEPROM STMicroelectronics http www st com internet analog product 250145 jsp 5 1 3 Temperature Sensor EEPROM LSM303DLH Manufacturer s product page for LSM303DLH STMicroelectronics http www st com internet analog product 147880 jsp 5 2 Finding out the Product s Article Number Revision and Serial Number MEN user documentation may describe several different models and or design revisions of the AE51 You can find information on the article number the design revision and the serial number on two labels attached to the board Article number Gives the product s family and model This is also MEN s ordering number To be complete it must have 9 characters Revision number Gives the design revision of the product Serial number Unique identification assigned during production If you need support you should communicate these numbers to MEN Figure 6 Labels giving the product s article number revision and serial number Complete article number CT NS ES 641517 Revision number Serial number MEN Mikro Elektronik GmbH 28 20AE51 00 E3 2011 12 23
20. on to the SBC board is realized via two pairs of AirMax VS connectors Figure 3 Connecting an AE51 and an SBC board via the AirMax VS connectors MEN Mikro Elektronik GmbH 14 20AE51 00 E3 2011 12 23 Interface to CPU Board 2 Interface to CPU Board The AE51 is connected to the SBC board via three AirMax VS connectors serving as a joint I O and graphics interface board Connector type e 72 pin AirMax VS press fit receptacle 6 rows right angle FCI 10114633 101LF Mating connector e 72 pin AirMax VS press fit 2 wall signal header 6 rows right angle header FCI 10052824 101LF The pin assignment matches the compatible SBC boards e g the SC24 and is not repeated here Please refer to the SBC board s manual for a complete list of signals MEN Mikro Elektronik GmbH 15 20AE51 00 E3 2011 12 23 Onboard Connectors 3 Onboard Connectors 3 1 Power Supply Connector The AE51 is supplied with 24 VDC nom 9 to 36 V via a 3 pin COMBICON connector An input voltage of 36 VDC nom can be realized as an option Connector type 3 pin COMBICON receptacle Phoenix Contact 1843800 MC 1 5 3 GF 3 5 Mating connector e 3 pin COMBICON plug e g Phoenix Contact 1863314 MCVR 1 5 3 STF 3 5 Table 1 Pin assignment of PSU connector 1 POWERCON IN _ Power input 00E 2 POWERCON GND Power input ground 3 IGNITIONCON Ignition 3 2 Power Bypass Connector optional If th
21. page 13 for the connectors exact positions The SATA interfaces support transfer rates up to 300 MB s Connector type e 7 pin SATA receptacle 1 27mm pitch Mating connector e 7 pin SATA plug 1 27mm pitch Table 3 Pin assignment of optional SATA connector S1 GND Digital ground S2 SATA_TX SATA transmit positive S S3 SATA TX SATA transmit negative S4 GND Digital ground S5 SATA RX SATA receive positive S6 SATA RX SATA receive negative S7 GND Digital ground Connector type 4 pin header for IDE drive power supply 2 5 mm Mating connector 4 pin IDE drive power plug 2 5 mm Table 4 Pin assignment of optional HDD SSD power supply connector 1 12V 12V power supply S2 GND12V Digital ground S3 GND5V Digital ground S4 45V 5V power supply MEN Mikro Elektronik GmbH 17 20AE51 00 E3 2011 12 23 Onboard Connectors 3 4 DisplayPort Interfaces Two of the DisplayPort interfaces available on the SBC board DisplayPort B on the DPI connector and DisplayPort C on DP2 can be accessed at the front panel Note Only DisplayPort B on the DP1 connector is a fully featured DisplayPort interface and offers AUX channel support and hot plug detection With the DisplayPort C interface on the DP2 connector the AUX lines are used for a USB connection This makes it impossible for the SBC board to exchange device management and control data with the display panel connected to this
22. rements of the German Federal Motor Transport Authority MEN Mikro Elektronik GmbH 4 20AE51 00 E3 2011 12 23 Block Diagram Front connector Graphics connector I O connector A 10 100 1000Base T E PCI Express Ethernet Mini Card A i A Py 10 100 1000Base T sE py MA Ethernet apes el ree i SIM i SM iCardA iCardB ED USB 2 0 URG C TENET i ZF SE 2 Er UART PGi Express Mu i MinicadB BL HD Audio SATA Bi MEN Mikro Elektronik GmbH 5 20AE51 00 E3 2011 12 23 Configuration Options Configuration Options I O DisplayPort 1 with USB channel instead of AUX channel HD audio Ribbon cable adapter to 9 pin D Sub front I O connector Antenna connectors For functions like WIFI WIMAX GSM GPRS UMTS in combination with PCI Express Mini Card s Reverse SMA connector Mass Storage Serial ATA SATA One port for external hard disk solid state drive Electrical Specifications Input voltage 36 VDC nom via front connector alternate internal PSU Input voltage 12 VDC via optional onboard power bypass connector As the product concept is very flexible there are many other configuration possibilities Please contact our sales team if you do not find your required function in the options For available standard configurations see online data sheet MEN Mikro Elektronik GmbH 6 20AE51 00 E3 2011 12 23 Product Safety Product Safety A Electrostati
23. t convey any license under its patent rights nor the rights of others Unless agreed otherwise MEN products are not designed intended or authorized for use as components in systems intended for surgical implant into the body or other applications intended to support or sustain life or for any other application in which the failure of the MEN product could create a situation where personal injury or death may occur Should Buyer purchase or use MEN products for any such unintended or unauthorized application Buyer shall indemnify and hold MEN and its officers employees subsidiaries affiliates and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unauthorized use even if such claim alleges that MEN was negligent regarding the design or manufacture of the part Unless agreed otherwise the products of MEN Mikro Elektronik are not suited for use in nuclear reactors or for application in medical appliances used for therapeutical purposes Application of MEN products in such plants is only possible after the user has precisely specified the operation environment and after MEN Mikro Elektronik has consequently adapted and released the product ESM ESMini MDIS MDIS4TM MDIS5 MENMON M Module M Modules SA Adapter SA Adapters UBox USM and the MBIOS logo
24. tching option 024 sesso e eens 26 Figure 6 Labels giving the product s article number r vision and serial number soon rS dea ais ERG ERE Re 28 Tables Table 1 Pin assignment of PSU connector 0 00 0 16 Table 2 Pin assignment of optional power bypass connector 16 Table 3 Pin assignment of optional SATA connector 17 Table 4 Pin assignment of optional HDD SSD power supply connector 17 Table 5 Pin assignment of 20 pin DisplayPort connector 18 Table 6 Signal mnemonics of 20 pin DisplayPort connector 18 Table 7 Pin assignment of USB front panel connectors 19 Table 8 Pin assignment of Ethernet front panel connectors 20 Table 9 Signal mnemonics of Ethernet front panel connectors 20 Table 10 Ethernet status LED socs i004 084 eme RR mer 20 Table 11 General status LEDs as depicted above 0200005 21 Table 12 Pin assignment of the HD audio onboard connector 22 Table 13 Pin assignment of the optional HD audio D Sub front connector 22 Table 14 Signal mnemonics of the HD audio interface 22 Table 15 Pin assignment of 52 pin PCI Express Mini Card connector 23 Table 16 Signal mnemonics of 52 pin PCI Express Mini Card connector 25 Table 17 SIM card switching Option see e Rt Rm RR eae ee 26 Taole 18 SMIBUSOEYIGeS ci scenerne see ES vis dE EIE 2
Download Pdf Manuals
Related Search