Order Ref: ISIM31
Contents
1. 1 LED DMX On DMX input present MASTER On Master Mode SLAVE On Slave Mode SOUND Flashing Sound activation 2 LED Display Used to show the various menus and the selected functions 3 Button MENU To select the programming functions v DOWN To go backward in the selected functions A UP To go forward in the selected functions ENTER To confirm the selected functions 4 Power IN OUT Used to connect the fixture to mains power 5 DMX IN For DMX512 link use 3 pin XLR plug cable to link the DMX controller and the fixture and input the DMX signal 6 DMX OUT For DMX512 link use 3 pin XLR plug cable to link the next fixture and output the DMX signal 7 Fuse T 6 3A Used to protect the fixture from damage of over current 8 Only For Remote Control Used to connect with CA 8 to control the fixture for Stand by Function and Mode select To select any functions press the MENU button until the required function is showing on the display Select the function by pressing the ENTER button and the display will blink Use the DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wai2. ZSolution Your integrated Solution ZMIOve 3505 Order Ref ISIM31 User Manual Please read the instructions carefully before use CONTENTS Safety Peta eta REB RR NEEDS 2 Technical Specifications onan eE Lini 4 HOW TO Set The UNIT ar od A A 6 ERINE TE AE E E col n A E 6 7 3 3 Home Position Adjustment 5 et a pio PX e rs RO dee eR 15 JHewto Cohtrol the DDIE ext hine e CURES UR a e Ends 16 4 1 Master Slave Built In Preprogrammed 16 A 2 Easy CODtFolle asi SEN CR Puoi aol tibus viai PIRE EE Ma Mer 17 17 sein eere ud 18 DNDOGODDBOLIOD 20 2 met perd p NR 21 MP 22 1 Safety Instruction N Please read ca
3. 14 3 3 Home Position Adjustment OFFSET MENU COLOUR OFFSET GOBO OFFSET R GOBO OFFSET Pan home position adjustment To select the bP Rd press the ENTER button to show the PAN OFFSET on the display Use the DOWN and UP button to adjust the value from 127 to 127 press the ENTER button to store Press the MENU button to exit Tilt home position adjustment To select the press the ENTER button to show the TILT OFFSET on the display Use the DOWN and UP button to adjust the value from 127 to 127 press the ENTER button to store Press the MENU button to exit Colour home position adjustment To select the lacet press the ENTER button to show the COLOUR OFFSET on the display Use the DOWN and UP button to adjust the value from 127 to 127 press the ENTER button to store Press the MENU button to exit Gobo home position adjustment To select the press the ENTER button to show the GOBO OFFSET on the display Use the DOWN and UP button to adjust the value from 127 to 127 press the ENTER button to store Press the MENU button to exit 15 Gobo rotation home position adjustment To select the lor bol press the ENTER button to show the R GOBO OFFSET on the display Use the DOWN and UP button to adjust the value from 127 to 127 press the ENTER button to store Press the MENU button to exit 4 How to Control the Unit There are three ways to control the unit
4. Fastening System 2 x Omega clamps Excellent ventilation for reliable operation Rotating Gobo Wheel 6 rotating and changeable gobos plus open Color Wheel 8 colors plus white Adjustable manual focus Pan Tilt Pan Tilt 540 270 Automatic Pan Tilt position correction Easy calibration and maintenance by magnetic home positioning Control 3 DMX control modes DMX Master Slave and Sound Active DMX channel modes 8 11CH LED display for easy navigation and addressing 0710096 smooth dimming and variable strobe speeds Data In Out 3 PIN XLR sockets 99999 RDA Remote DMX addressing DMX address can be remotely set up by universal controller Specification Power Voltage AC 100 240V 50 60Hz Power Consumption 134W Light Source 1 x 60W white LED Beam Angle 15 e Fuse T 6 3A Dimensions 292 x 252 x 425mm Weight 7 2kgs 3 How To Set The Unit o 2 A 0 5 NS i
5. exit the menu mode SHOW MODE To select the press the ENTER button to show the SHOW MODE on the display Use the DOWN UP button to select the GRT Show 1 Show 2 3l Show 3 or Show 4 mode Once the show mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode SPLIT COLOUR MODE To select the PLE press the ENTER button to show the SPLIT COLOUR MODE on the display Use the DOWN UP button to select the HES split colour mode or normal Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode SLAVE MODE To select the 5111 press the ENTER button to show the SLAVE MODE on the display Use the DOWN UP button to select the SL normal 2 2 light show mode the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode 1 BLACKOUT MODE To select the press the ENTER button to show the BALCKOUT MODE on the display U
6. 1 Master slave built in preprogram function 2 Easy controller 3 Universal DMX controller No need to turn the unit off when you change the DMX address as the new DMX address setting will be in affect at once Every time you turn the unit on it will show 42 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an select Gh 1 show 1 instant show You have to set the first unit in master mode Show 2 Eh 3l Show 3 or ah show 4 mode Its DMX input jack will have nothing plugged into it and its master LED will be constantly on and sound LED will flash to the music The other units will have to be set in slave mode and select normal 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights will be constantly be on 2 light show In slave mode Si means the unit works normally and means 2 light show In order to 16 create a great light show you can set on the second unit to get contrast movement to each other even if y
7. 255p 540 255 270 248 255 240 247 Strobe 194 Rotation Slow 232 239 open 190 193 Stop P 189 Rotation Slow 190 231 Sow close Q 128 Rotation Fast 182 189 Open 120 127 Gobo7 shaking 110 119 Gobo6 shaking 140 181 Siow open 101 109 Gobo shaking 092 100 Gobo4 shaking 132 139 meee 083 091 Gobo3 shaking 44 074 082 Gobo2 shaking 064 073 Gobo1 shaking 016 131 24 056 063 Gobo7 048 055 5 040 047 Gobo5 mf 032 039 Gobo4 024 031 Gobo3 2 008 015 Open 016 023 Gobo2 0 0 0 0 000 007 Blackout 008 015 Gobo1 000 007 Open Ch5 Ch6 Ch7 Ch8 Colour Wheel Colour Wheel i Normal Split Colour Mode Function 255 Rotation Fast 255 Rotation Fast 128 Rotation Fast 255 100 250 255 Sound Active 210 249 No Function 194 Rotation Slow 194 Rotation Slow C 200 209 Reset All 190 193 Stop 190 193 Stop 130 199 No function 194 Rotation Slow 189 Rotation Slow 189 Rotation Slow 120 129 Disable blackout while Gobo changing 190 193 Stop n 110 119 Enable blackout 128 Rotation Fast 128 Rotation Fast while Gobo changing 120 127 Colour8 189 Rotation Slow 113 127 Colour8 113 119 Colour7 Colour8 100 109 Disable blackout 099 112 Colour 105 112 Colour while Color changing 085 098 Colour aca 071 084 Colours 104 Colour6 Colour7 090 099 Enable blackout 090 097 Colour6 while Color changing 057 070 Colour4 083 089 Colours Coloure 128 Rotation Fast 043 056 Colour3 075 082 Colours 080 089 Disable
8. button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode To select the 55 press the ENTER button to show the TEST on the display and the unit will run a self test To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode 12 TEMPERATURE To select the press the ENTER button to show the TEMPERATURE on the display and the display will show the temperature of the unit To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode ttt 1 FIXTURE HOURS To select the press the ENTER button to show the FIXTURE HOURS on the display and the display will show the number of working hours of the unit To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode SOFTWARE VERSION To select the tr press the ENTER button to show the SOFTWARE VERSION on the display and the display will show the version of software of the unit To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode DEF
9. AULTS SETTING To select the Ici E press the ENTER button to show the DEFAULTS SETTING on the display Use the DOWN UP button to select the HES or Once the has been selected press the ENTER button and use the DOWN UP button to select the Pir a PRO Defaults or AUTO Defaults mode a For professional users detailed explanation as followings nid gt BPLE gt BES ud E L d gt L 13 8 aL na J vv 21 j Huc a Mostly automatic mode for non professional users detailed explanation as followings a 22 a r ZI Un Se Z ral 1 Notice Other settings NOT changed while choosing Defaults Setting Press the ENTER button and the corresponding functions will set to defaults setting To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode RESET To select the press the ENTER button to show the RESET on the display Press the ENTER button and all channels of the unit will return to their standard position
10. Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55103 1 2009 EN55103 2 2009 EN62471 2008 EN61000 3 2 2006 A1 2009 A2 2009 EN61000 3 3 2008 amp Harmonized Standard EN 60598 1 2008 All 2009 EN 60598 2 17 1989 A2 1991 EN 62471 2008 EN 62493 2010 Safety of household and similar electrical appliances Part 1 General requirements 22 English Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with seperate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please seperate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed w
11. blackout while Pan Tilt moving 029 042 Colour2 068 074 Colour4 ColourS 22 4 7 ing 015 028 Colour 060 067 Coloura iode 000 014 White 053 059 3 Colour4 9 045 052 Colour3 000 069 No Function 038 044 Colour2 Colour3 030 037 Colour2 023 029 Colour1 Colour2 015 022 Colour 008 014 White Colour1 000 007 White 18 11 Channel Mode 11 Channels Mode Speed Dimmer 255 255 100 248 255 Open 240 247 232 239 Random Strobe Open Fast Open Slow Close 190 231 182 189 Open Fast Close 140 181 Slow Open 132 139 _Open Fast 016 131 gt gt Slow 008 015 Open 000 007 Blackout Ch8 Ch9 Ch10 Ch11 Colour Wheel Colour Wheel Normal Colour Mode Gobo R Gobo Function 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow 255 Rotation Fast 2 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow O 128 Rotation Fast 128 Rotation Fast 2 194 Rotation Slow 190 193 Stop 189 Rotation Slow 250 255 Sound Active 210 249 No Function 200 209 Reset All 130 199 function 120 129 Disable blackout while Gobo changing 110 119 Enable blackout while Gobo changing 120 127 Colours 120 127 Gobo7 shaking 113 119 Colour7 Colour8 440 119 shaking 100 109 ee 2 128 Rotati
12. ctors cables to see if linking properly If the DMX LED is on and no response to the channel check the address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one Try to use another DMX controller Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit Some fixtures don t respond to the easy controller You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal No response to the sound Make sure the fixture does not receive DMX signal Check microphone to see if it is good by tapping the microphone 21 E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 8 Fixture Cleaning Cleaning must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates moist smoky or particularly dirty surroundings can cause greater accumulation of dirt on the fixture Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days Declaration of
13. ely Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorised technical assistance center Always use the same type spare parts DO NOT touch any wire during operation as high voltage might cause electric shock Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture DO NOT open the unit within fifteen minutes after switching off The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Caution There are no user serviceable parts inside the unit DO NOT open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via omega bracket see below Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating And make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture Professionals must fit the equipment It must be fixed at a place where is out of reach and has no one passing by or under it 2 Technical Specifications Construction Stylish design with fire retardant plastic housing
14. enu mode d 5P Display normal mode for the fixture putting on the floor d a Display inversion mode for the fixture fixing under ceiling 11 Mi Il FOCUS POSITION To select the Foul press the ENTER button to show the FOCUS POSITION on the display Then press the ENTER button and the unit will run the built in programmed for focus positioning To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode C JU FUNCTION DELAY To select the Fudd press the ENTER button to show the FUNCTION DELAY on the display Use the DOWN UP button to select the delay time 0 no delay or 1 2 3 Wait for 1 2 3 seconds before these Functions of 8 11 CH are activated deactivated Once selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode Jr qc L H i DIMMER CALIBRATION To select the ID HL press the ENTER button to show the DIMMER CALIBRATE on the display Use the DOWN UP button to calibrate the dimmer for a maximum output from 50 limited to 5096 of the really max output to 100 maximum output is not limited Once calibrated press the ENTER button to setup to go back to the functions without any changes press the MENU
15. er a 120 ohm 1 4W resistor between pin 2 DMX and 3 DMX into a 3 XLR plug and plug it in the DMX output of the last unit 2 Connect the unit together a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 3 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 4 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 5 The end of the DMX 512 system should be terminated to reduce signal errors 20 6 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 5 Not used 7 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A 9 The fixture does not work no light Check the connection of power and main fuse Measure the mains voltage on the main connector Not responding to DMX controller DMX LED should be on If not check DMX conne
16. ith other commercial wastes for disposal www prolight co uk Innovation Quality Performance 23
17. on Fast 105 112 Colour7 101 109 Gobo5 shaking O WOT Bore henang ng 098 104 6 Colour 113 127 Colour 599 092 100 Gobo4 shaking 099 112 Colour 083 089 Colours Colours 083 091 Gobo3 shaking 128 Rotation Fast 080 089 Disable blackout assent 075 082 Colours 074 082 Gobo2 shaking while Pan Tilt moving olour 068 074 Colour4 Colours 064 073 1 shaking 000 127 Index oroS Enable dicek 071 084 Colour5 060 067 Colours 056 063 Gobo7 0 360 while Pan Tilt moving 053 059 Colour3 Colour4 048 055 Gobo6 057 070 Colour4 045 052 Colour3 000 069 No Function 040 047 5 043 056 Colour3 038 044 Colour2 Colour3 032 039 Gobo4 030 037 Colour2 029 042 Colour2 023 029 Colour1 Colour2 024 031 Gobas 016 023 Gobo2 015 028Colouri 015 022 Colour 000 014 White 008 014 White Colour1 000 007 White 008 015 Gobo1 000 007 Open O O06 1 Gobo 2 Gobo 3 19 Gobo 4 Gobo 5 Gobo 6 6 DMX Connection Unit 1 Unit 2 Unit 3 Unit 4 DMX OUTPUT DMX512 CONTROLLER COMMON DMX INPUT Hm DMX OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture CABL59 CABL90 1 At last unit the DMX cable has to be terminated with a terminator Sold
18. ou have only two units 4 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote controller on the first unit will control all the other units for Stand by Function and Mode selection Controller Stand By Blackout the unit Function 1 Sync Strobe Show 1 Press to select color 2 Async strobe 1 4 2 Hold to select gobo 3 Sound Strobe Mode Sound Show LED ON LED OFF LED Slow Blinking 4 3 DMX Controller Using a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the is showing on the display Press the ENTER button and the display will blink Use the DOWN and UP button to change the DMX512 address Once the address has been selected press and keep the ENTER button pressed up to when the display stops blinking or storing automatically 7 seconds later To go back to the functions without any change press the MENU button again Please refer to the diagrams on the next page to address your DMX512 channel for the first 4 units 17 8 Channel Mode 11 Channel Mode 5 DMX512 Configuration 8 Channel Mode 8 Channels Mode Ch1 Ch2 Ch3 Ch4 Pan Tilt Shutter Gobo 255 Rotation Fast
19. refully the instruction which includes important information about the installation usage and maintenance WARNING Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction manual Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect mains power before replacement or servicing Make sure there are no flammable materials close to the unit while operating as it is a fire hazard Use a safety cable when mounting this unit DO NOT handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 85 DO NOT touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing or servicing In the event of a serious operating problem stop using the unit immediat
20. se the DOWN UP button to select the HES blackout or normal mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode SOUND MODE To select the i2 press the ENTER button to show the SOUND MODE on the display Use the DOWN UP button to select the Len sound mode on or sound mode off Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode 7 SOUND SENSE To select the BOSE press the ENTER button to show the SOUND SENSE on the display Use the DOWN UP button to adjust the sound sensitivity from 0 to 100 Once selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode 10 PAN INVERSION To select the Fin press the ENTER button to show the PAN INVERSION on the display Use the DOWN UP button to select the HES pan inversion or normal mode Once the mode has been selected press the ENTER button to setup to go back
21. t for one minute to exit the menu mode The main functions are on the next page Pa PF DMX512 ADDRESS CHANNEL MODE BREL SHOW MODE NN L SPLIT COLOUR MODE SLAVE MODE LET i BLACKOUT MODE SOUND MODE SOUND SENSE NORMAL PAN INVERSION NORMAL TILT INVERSION LED DISPLAY ON LED DISPLAY OFF NORMAL DISPLAY INVERSION FOCUS POSITIONING FUNCTION DELAY DIMMER CALIBRATE TEST TEMPERATURE FIXTURE HOURS SOFTWARE VERSION PRO Defaults AUTO Defaults Ey DMX 512 ADDRESS To select the press the ENTER button to show the DMX ADDRESS the display Use the DOWN UP button to adjust the address from 1 to 512 Once the address has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode Chid CHANNEL MODE To select the Caro press the ENTER button to show the DMX CHANNEL MODE on the display Use the DOWN UP button to select the 8 CH or 11 CH mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to
22. to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode TNT IC I5 TILT INVERSION To select the press the ENTER button to show the TILT INVERSION on the display Use the DOWN UP button to select the tilt inversion or na normal mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode LED DISPLAY To select the press the ENTER button to show the LED DISPLAY on the display Use the DOWN UP button to select the on LED display on or LED display off mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the menu mode DISPLAY 1 press the ENTER button to show the DISPLAY on the display Use the LU T To select the DOWN UP button to select the 5 159 normal 85 display inversion To go back to the functions without any changes press the MENU button again Hold and press the MENU button for one second or wait for one minute to exit the m
Download Pdf Manuals
Related Search