Home
Waterproof - Ness Corporation
Contents
1. To add and delete card users by Manager cards Toadd card userby ManagerAdd Card To delete card User by Manager Delete Card Manager add card Read card Manager add card Cards canbe added continuously Manager delete card Read Card Manager delete card Cards can bedeleted continuously To unlock thedoor For aPIN user Enter the PIN then press For acard user Read card For a card and PIN user Read card then ente PIN 10 2 Door Relay Door Open Detection Alarm Facility code Settings Door relay time setting Door relay time setting The door relay timeis between 0 99 seconds the factory default settingis 5 seconds Door Open Detection Door Open Too Long DOTL warning When used withan optional magnetic contact or built in magnetic contact of thelock if thedoor is openednormally butnot closed after 1 minute theinside buzzer will beepautomatically to remind peopleto close the door andcontinue for 1 minute before switching off automatically Door Forced Openwarning When used withan optional magnetic contact or built in magnetic contact ofthe lock ifthe door is forced open orif the dooris opened after 20 seconds of the electro mechanical lock not closed properly the inside buzzer and alarm output willboth operate The Alarm Output time is adjustable between0 3 minutes with the default being 1 minute
2. odisable door open detection 6 LO Factory default setting oenable door open detection 6 2 L Alarm output time oset the alarm output time 0 3 minutes Factory defaultis 1 minute 9 o 3 Keypad Lockout amp Alarm Output options If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes or the alarm will operate for 10 minutes depending on the option selected below ormai Statie No keypad lockout 7 0 A Factory default setting 10 Keypad Lockout 7 0A Alarm Output TPE To remove the alarm Toreset the Door Forced Open warning Read valid cardjor Master Code Toreset the Door Open Too Long warning Close the door or Read valid cardjor Master Code Toset the facility code To set the facility code of W1 W3 8 Facility code Repeat Facility codel B Facility Code can be any number between This operation might be required 1 255 Default 0 when W1 W3 B is acting as wiegand reader and connectingto 11 Interconnecting Two Devices 11 1 W1 W3 B operating as aWiegand Output Reader In this mode the W1 W3 B supports a Wiegand 26 bit output sothe Wiegand data lines can be connectedto any controllerwhich supports a Wiegand 26 bitinput See figure 1
3. Power Controller With Wiegand 26 inPut W1 W3 B 11 Transmission Format 1 Keypad Transmission The Reader willtransmit the PIN data when itreceives the lastkey press after PIN code Format Facility Code PIN Code Facility code is anydigits between 0 255 factorydefault is 0 Pincode is any 1 4 digits between 0 9999 Example Facility code 1 PIN code 5678 Press 5678 then the output format will be 00105678 2 Proximity Card Transmission The Reader willtransmit the carddata when itreads the Card Format Card Number the last8 digits of CardNumber Remarks No matter the card or pinis valid orinvalid the data will be transmitted 11 2 W1 W3 B operating as aController In this mode the W1 W3 B supports a Wiegand 26 bit input so an external Wiegand device with a 26 bit output can be connected to the Wiegand input terminals on the W1 W3 B Either an ID card reader 125KHZ or an IC card reader 13 56MHZ can be connected tothe W1 W3 B Cards are required tobe added atthe external reader except where anexternal EM readeris used inthis case cardscan be addedat either reader or controller See figure 2 Special Power Supply W1 W3 B 12 W1 W3 B Quick Reference Programming Guide To enter the programming mode Master code 888888 is the default factory master code To exit from the programming mode X Note that to
4. Packing list Name Quantity Remark Digital Keypad W1 W3 B 4 User Manual 1 Screw driver 1 Rubber bungs 4 6 27mm used for fixing Self TappingScrews 4 3 5 27mm used for fixing Manager Card 2 Manager Add Card amp Manager Delete Card Please ensure that allthe above contents arecorrect If any aremissing please notify the supplier of theW1 W3 B 2 Description W1 B amp W3 B are in thesame function only different in shape W1 W3 B is single door multifunction access controller or aWiegand output keypad or card reader Itis suitable for mountingeither indoor or outdoorin harsh environments It is housed ina strong sturdy and vandal proof Zinc Alloy electroplated case The electronics are fully potted sothe W1 W3 B is waterproof and conforms to IP68 The W1 W3 B supports upto 2500 users ineither a Card 4digit PIN or aCard PIN option The inbuiltcard reader supports EM 125KHZ frequency card Tag The W1 W3 B has many extra features including block enrollment wiegand 26 bits interface and backlit keypad etc These features make the W1 W3 B anideal choice Tor door access notonly for small shops and domestic households but alsofor commercial andindustrial applications such as factories warehouses laboratories banks and prisons 3 Features Waterproof conforms tolP68 Strong Zinc AlloyElectroplated anti vandal case Full programming fromthe keypad 2500 users supports Card PIN Card PIN Can be useda
5. To add a PIN users 1 User ID numbed PINA The ID number is any number between 1 2500 The PINis any fourdigits between 0000 9999 with the exception of 1234 which is reserved Users can be added continuously without exiting from programming mode as follows 1 User ID No T A PINA PINA UserID No 2 To Deletea PIN user 2 User ID number Users can be deleted continuously without exiting programming mode Tochange the PIN of a PINuser Note This step must bedone out of E D number 4 OldPIN New PIN New PIN A programming mode To add a card user Method 1 4 Read Card This is afast way toenter cards using ID number auto generation To add a card user Method 2 This is the second way to enter cards using UserID Allocation In this methoda User IDis allocated to a card Only one userID can be allocated to asingle card Toadd card user Method 3 Adda series cards users Block Enrollment Cards can beadded continuously without exiting programming mode T UD number Card L Card quantity 5 ID number 8 digits Card number Card quantity is between 1 2500 The 8 digits card number is the last 8 digits on the card Maximum 2500 cards can be enrolled ata stretch within 3 minutes To deleteca
6. undertake the following programming the master user must be logged in To change the master code To add a PIN user 0 New code New code The master code is any 6 digits 1 UserID number PIN HH The ID numberis any number between 1 2500 The PIN is any four digits between 0000 9999 with the exception of 1234 whichis reserved Users can beadded continuously without exiting programming mode To add a card user To delete aPIN or a card user 1 Read Card A Cards can be added continuously without exiting from programming mode 2 User 1D number for a PIN user or BP Read Card for a card user Users can be deleted continuously withou exiting from programming mode To Unlock the door To unlock the door for a PIN user F Enter the PIN then press To unlock the door for a card user Present the card 13
7. Alarm The W1 W3 B uses a LDR light dependent resistor as an anti tamper alarm If the keypad is removed from the cover then the tamper alarm will operate 9 Sound and Light indication Operation Status Red Light Green Light Blue Light Buzzer Power on Bright Short Ring Stand by Bright Press keypad Short Ring Operation successful Bright Short Ring Operation failed 3 Short Ring Enter into programming mode Bright Short Ring In the programming mode Bright Exit from the programmingmode Bright S a Short Ring Open the door N Bright N Short Ring Alarm Bright S Alarm 10 W1 W3 B Detailed Programming Guide 10 1 User Settings Toenter the programming mode E Master code Z 888888 is thedefault factory master code X Toexit from the programming mode Note that to undertake the following programming the master user must be logged in 0 New code New code The master code isany 6 digits Tochange the mastercode Setting the working mode Set valid card only users 3 0 Entry is by Card only Set valid cardand PIN users B 0 Entry is by Card and PIN together Set valid card or PIN users 3 2 Entry is byeither Card or PIN default To add and delete users in eithercard or PIN mode 212 H Default setting
8. INEZ CORPORATION Waterproof Keypad Reader Controller EDBODE fie z User manual E 2 Fa a S g E D L LT CORPORATION nS as feo A www ness com au Australia Y largest HEAD OFFICE designer and Ness Corporation Pty Ltd KEON ABN 28 069 984 372 manufacturer of Ph 61 2 8825 9222 Fax 61 2 9674 2520 high quality security ness ness com au products SYDNEY Ph 02 8825 9222 Fax 02 9674 2520 sales ness com au MELBOURNE Ph 03 9875 6400 Fax 03 9875 6422 MADE IN nessmelb ness com au AUSTRALIA BRISBANE Ph 07 3399 4910 Fax 07 3217 9711 Q nessbris ness com au PERTH Ph 08 9328 2511 Fax 08 9227 7073 nessper ness com au ADELAIDE Ph 08 8152 0000 Fax 08 8152 0100 adelaide ness com au L N55 C INSTALLATION amp PROGRAMMING MANUAL For products 101 095 Ness W1 B Ultraprox Reader Controller COPYRIGHT NOTICE All rights reserved No part of this publication may be reproduced transmitted or stored in a retrieval system in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Ness Ness reserves the right to make changes to features and specifications at any time without prior notification in the interest of ongoing product development and improvement 2011 Ness Corporation Pty Ltd ABN 28 069 984 372 1
9. for the cable Fix the back cover firmly onthe wall with 4 flat head screws Thread the cable through the cable hole Attach the keypad to the back cover PCB connect diagram 6 Wiring Colour Function Description Green DO Wiegand Output DO White D1 Wiegand Output D1 Grey Alarm Alarm Negative Yellow OPEN Request to Exit Button Brown D IN Door Contact Red 12V DC Powerlnput Black 12V DC PowerInput Blue NO Relay NO Purple COM Relay COM Orange NC Relay NC Pink GND W1 W3 B Negative Connection Diagram Alarm Power Alarm Power Lo W1 W3 B Power Electric boltNC Electric strikeNO Common Power Supply Purple Orange N W1 W3 B Special Power Supply Notes Connect the negative poleof the lock toNC is for Failsafe lock Connect the negative poleof the lock toNO is for Fail secure lock 7 To Resetto Factory Default To reset to factory default power off press hold it and power on release it until hear two beeps and the LED shines in orange then read anytwo EM cards the LED will turn in red means reset to factory default setting successfully Of the two EM cards read the first one is Manager Add card the second one is Manager Delete card Remarks Reset to factory default the user sinformation is stillretained 8 Anti Tamper
10. rd user by card number Note Users canbe deleted continuously without exiting from programming mode To delete a card user by user ID This option can be used when a user has losttheir card 2 Read Card NI User ID To add and delete users in cardand PIN mode 3 1 FH To Adda card and Pin user The PIN is any four digits between 0000 9999 with the exception of 1234 which is reserved To change a PIN in card and PIN mode Method 1 Note that this is done outside programming mode so the user can undertake this themselves Add the cardas for acard user Press to exit from the programming mode Then allocate thecard a PINas follows LZ Read Card 1234 PIN PIN FJRead Card lOld PIN New PIN New PIN To change a PIN in card and PIN mode Method 2 Note that this is done outside programming mode so the user can undertake this themselves Fl number OldPIN New PIN New PIN To deletea Card and PIN user just delete the card 2 User IDI To add acard user in cardonly mode 3 0 ToAdd and Delete acard user The operating isthe same asadding and deleting a card userin 3 2 To deleteAll users To delete ALL users Note that this is adangerous option so use with care 2 0000
11. s a standalone keypad Programmable one relay output Backlight keypad Wiegand 26 input amp output Adjustable Door Output time Alarm time DoorOpen time Block enrollment can enroll maximum 2500 consecutive card within 3 minutes Very lowpower consumption 60Ma Fast operating speed lt 20mswith 2500 users Easy to installand program Built in light dependent resistor LDR for anti tamper Built in buzzer Red Yellowand Green LEDsdisplay the working status 12VDC Operation Two year warranty 4 Specifications Operating Voltage 12VDC Operating Humidity 5 95 RH User Capacity Keypad Card Type 2500 12 keys 2 x6 digits W1 B 12 keys 3 x4 digits W3 B EM 125 KHZ card Tag Environment Conforms to IP68 Adjustable Door Relay time 0 99 seconds Adjustable Alarm Time 0 3 minutes Wiegand Interface Wiegand 26 input amp output Card Reading Distance 3 6 cm Wiring Connections Electric Lock Exit Button Active Current lt 80mA DOTL External Alarm Idle Current lt 40mA L135 xW58 xH26 mm W1 B Dimensions Lock Output Load Max 2A L128 xW82 xH28 mm W3 B Alarm Output Load Max 20A Net Weight 550g Operating Temperature 25 60 C Gross Weight 700g ll loa uy Hm T 5 Installation Remove the back cover from the keypad using the supplied security screwdriver Drill 4 holes on the wallfor the screws and hole
Download Pdf Manuals
Related Search
Related Contents
ASUS Transformer Pad User Manual alpha 360° Quad manual Fr ABSol TRD-。42G フウガ ベンチ クッション付 取扱説明書(お客様保管用) Samsung 48" SUHD 4K Curved Smart TV JS9005 Bruksanvisning Visualizador de imagem Kodak EasyShare Copyright © All rights reserved.
Failed to retrieve file