VK910 Matrix Full Manual
Contents
1. Channel Set Press the ENTER button to confirm the present set will blink on the display Use the UP and DOWN button to select channel 1 16 48 Once the set has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Show Mode Select Show Mode Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Show 1 or Show 2 or Show 3 or Show 4 mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Slave Mode Select Slave Mode Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Slave 1 normal or Slave 2 2 light show mode Once the mode has been selected press the EN TER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Black Out DMX Fail Select Slave Mode Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Yes yes blackout or No no blackout mode Once the mode has been selected press the ENT2. ER but ton to setup to go back to the functions without any change press the MENU but ton again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Sound State Mic on Off To set sound control on or off disenabled select Sound State Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the On Sound On or Off Sound Off mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Sound Sense Sensitivity To set the sensitivity of the built in microphone select Sound Sense Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the 0 100 mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Pan Inverse Select Pan Inverse Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Yes Pan Inversion or No Normal mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and pres
3. LED 3x3 Matrix MOVING HEAD User s Manual Viking VK910 Professional Entertainment Technology 1 WARNING Safety Instructions Please read carefully the instructions which includes important information about the installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet DO NOT connect this product to the mains via a Dimmer Unpack and check carefully there is no transportation damage before us ing the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before replacement or servicing Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety bonds when hanging this unit Don t handle the unit by taking its head only always hold by the base handles Maximum ambient temperature is 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation
4. Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest Viking Dealer for assistance To prevent or reduce the risk of electrical shock or fire do not expose the unit the rain or moisture The unit is for indoor use only Use only in a dry location The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest Viking Lighting dealer Installation The unit should be mounted via its screw holes on the omega bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping white operating Make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight Also always use a safety cable rated to 15kg SWL when installing the fixture from the Omega Hanging Bracket The equipment must be fixed by professionals who have accessed it s use is safe and proper Technical Specification Extremely small fast and powerful LED Moving beam DMX Channels 1 16 48 Chann
5. anu Test Manual Test Select Manu Test press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Pan Tilt Red Green Blue White Dimmer or Strobe Once the mode has been selected press the ENTER button to setup use the DOWN and UP button to change the value 0 255 Once the mode has been selected press the ENTER button to setup go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Fixture Test Select Manu Test press the ENTER button to confirm present mode will blink on the display Once the mode has been selected press the ENTER button to setup go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Temperature Press the MENU button up to when the Temp is blinking on the display Pressing ENTER button and the display will show the temperature of the unit To go back to the functions press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Defaults Setting Press the MENU button to show Defaults on the display Press the ENTER button and the display will blink Use the DOWN and UP button to select the YES or No Once the Yes has been selected press the ENTER button and use the UP an
6. d Down button to select the PRO Defaults or AUTO Defaults PRO Defaults For professional users Slave Mode Slave 1 Black Out Yes Sound State Off Pan Inverse No Tilt Inverse No Back Light Off Function Delay 3S Delay AUTO Defaults Mostly automatic mode for non professional users Slave Mode Slave 1 Black Out No Sound State On Pan Inverse No Tilt Inverse No Back Light On Press the MENU button until Reset is blinking on the display Pressing the ENTER button will reset the head and all channels of the unit will return to their standard position 5 How to Control The Unit You can operate the unit in two ways 1 Master Slave built in preprogram function 2 Universal DMX controller There is no need to turn the unit off when you change the DMX address as new DMX address settings will take effect at once Every time you turn the unit on it will show A PO on the display and move all the motors to their HOME position You may hear some noises for about 20 seconds after which the unit will have completed it s reset and will be ready to receive DMX signal or run the built in programs Master Slave Built In preprogrammed Function By using the units in master slave configuration the first unit will control the other units to give an automatic sound activated synchronized light show This function is ideal when you want an instant show You have to set the first unit to master Show Mode and sel
7. ect Show 1 Show 2 Show 3 or Show 4 mode Its DMX input socket MUST have nothing plugged into it and its master LED will be constantly on and sound LED will flash to the music The other units will have to be set to Slave mode and select Slave 1 normal or Slave 2 2 light show mode Their DMX cables plugged into the DMX input sockets daisy chained and the slave led lights will be constantly on 2 Light Show In Slave mode Slave 1 means the unit works normally and Slave 2 means 2 light show In order to create a great light show you can set Slave 2 on the second unit to get contrast movement to each other even if you have two units only You can decide which lights are to be Slave 1 and Slave 2 and build an interesting display with no controller required DMX Controller By using a universal DMX Controller to control the units you will need to set DMX address from 1 to 512 so that the units can receive a DMX signal Press the MENU button until the DMX Address is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to store the address To go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode 6 Troubleshooting Following are a few common problems that may occur during operation Here are some su
8. el Modes Master Slave Sound amp DMX Modes Pan Tilt 540 270 degrees speed adjustable Smooth electronic dimming 0 100 Electronic strobe with pulse and random effects High efficiency low power consumption low noise Super compact low weight fast moving Powercon in and out connectors DMX on 3 pin in and out XLR connectors All 9 Led individually controllable Built In Programs 9 x 10w 4in1 Quad Colour LED Weight 7 5kg Voltage 100 240v 50 60hz 120w Fuse External T6 3a 20mm Dimensions 292x187x324mm 00000000000000000N 3 DMX512 Connection COMMON DMX DMX INPUT DMX OUTPUT DMX Termination reduces signal errors and avoids signal transmission problems amp interference It is always advisable to connect a DMX signal terminator At the end of the signal run See Point 2 below 1 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable Route signal cables away from mains cables to avoid signal interference commonly viewed as lights flickering randomly 2 Atthe last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4w resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Con
9. gain Hold and press the MENU button about one second or wait for one minute to exit the menu mode The main functions are showing overleaf DMX Address 0 512 Select DMX starting address for the light Channel Set Xch Select DMX Channel Mode 10 13 or 17 control channels Show Mode Select inbuilt show 1 2 3 or 4 Slave Set SlaveX Select either slave1 normal or slave2 for light show slave Select if you wish the unit to blackout in loss of DMX signal Sound Mode JOn Off Select if the auto sound trigger is on or off 0 100 Select sensitivity of built in mic to trigger sound activation Tilt Inverse Invert Tilt on Head Back Light On Off Select if LCD backlight is to be constantly on or auto off White Balance R G B 0 255 Reset the head to factory defaults Manual test RGBW Dimmer amp Strobe functions 255 Temp Shows the internal temperature of the head Defaults Yes No Reset to factory defaults either Pro or Auto basic level Pro Auto Lal DANIAN DMX Address Select DMX Address Press the ENTER button to confirm the present address will blink on the display Use the UP and DOWN button to adjust the address from 1 to 512 Once the address has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode DMX Channel Set Select
10. ggestions for easy troubleshooting A Theunit does not work no light and the fan does not work 1 Check the connection of power and main external use 2 Check the Powercon Plug is lock twisted correctly 3 Check the power on LED B Notresponding to DMX controller 1 DMXLED should be on If not check DMX connectors cables etc to see if it is linked properly 2 Ifthe DMX LED is on and no response to the channel check the address setting and DMX polarity and also desk profile is correct for the mode 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller or know light on same settings amp address 5 Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the Master Slave mode signal 2 Wrong DMX address in the unit Set the proper address D Noresponse to the sound 1 Make sure the unit does not receive a DMX Signal this overrides the sound 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or cable connected to PCB is broken 2 The wrong profile or DMX mode is set on the controller 7 Fixture Cleaning The cleaning of in
11. nect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable cannot branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the systems 4 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 5 Each light needs to have an address set to receive the data sent by the con troller The address number is between 1 512 6 3 pin XLR connectors are equally as popular as 5 pin XLR In both cases the following protocol applies XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Display To show the various menus and the selected functions LED DMX Input Present Slave Mode Button MENU To select the appropriate option WN To go backward in the selected function UP To go forward in the selected function ENTER To confirm the selected value or function 4 Main Function To select any of the given functions Press the MENU button until the required function is showing on the display Select the function by pressing the ENTER button and the display will blink Use the DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to confirm selection or to go back to the functions without any change press the MENU button a
12. s the MENU button about one second or wait for one minute to exit the menu mode Tilt Inverse Select Tilt Inverse Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Yes Tilt Inversion or No Normal mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode Back Light LCD backlight Select Back Light Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the On LED On or Off LED Off mode Once the mode has been selected press the ENTER button to setup to go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode White Balance Select White Balance press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP button to select the Red or Green or Blue Once the mode has been selected press the ENTER button to setup use the DOWN and UP button to change the value 125 255 Once the mode has been selected press the ENTER button to setup go back to the functions without any change press the MENU button again Hold and press the MENU button about one second or wait for one minute to exit the menu mode M
13. ternal and external optical lenses and or lenses must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean any dust from intake air vents or fan surrounds 8 DMX Channels 1 1 DMX Channels 16 0 255 Pan 0 630 Degree Channel 0 255 0 255 0 255 Channel 0 015 016 035 036 055 056 075 076 095 096 15 116 135 136 155 156 175 176 195 196 2315 216 235 236 255 7 000255 DMX Channels 16 Channels continued 11 12 13 14 Master Dimmer Strobe Open Strobe Slow to Fast Open Strobe Fast Close Slow Open Open Strobe Fast Open Slow Close Random Strobe 000 255 All Led s Red 000 255 All Led s Green 000 255 All Led s Blue 000 255 All Led s White DMX Channels 48 Channels Channels 1 to 10 as per the 16 channel mode m ems enge p pns UT Led 2 9 Colour RGBW s
Download Pdf Manuals
Related Search