Owner`s Manual
Contents
1. 1 Place the gear selector in park 2 Set the parking hand brake 3 Be certain your foot is off the brake pedal 4 Press the program Push Button switch 2 times within 5 seconds parking lights will flash two times indicating the mode was successfully en ered If your parking lights flashed four times this indicates the turbo mode was on and is now turned off 25 With the turbo timer mode selected on after you ve arrived at your destination while the engine is still running set the parking brake pause 2 seconds then turn the ignition switch to the off position The engine will continue to run the allotted time according to the selection during installation l If you do not want the vehicle to continue to run for one cycle simply step on the vehicle s brake or release the parking brake or activate the transmitter s start button two times in succession Any of these will cause the engine to turn off TELEMATIC UPGRADE l This system has the ability to have a telematic upgrade module connected to it This is a upgrade that can give you control of certain functions of your vehicle from a Telephone or in some cases a computer interface Please check with your installation center for most recent Telematic Upgrades If you had a Telematic Upgrade installed the manual supplied with the upgrade unit will provide a opera tors manual advising of the features of the system and means available to control these features2. Check Temperature Only available on certain remote start units Press the option key buttons simultaneously for 1 second The vehicle s alarm will display the temperature Temperature is read from the alarm s module located below the dashboard This reading may be higher than actual ambient temperature due to the greenhouse and is relative only to the inside vehicle temperature Temperature Start Mode Available on certain models To toggle this feature on or off from the armed mode press the Option amp Unlock Buttons simultaneously the temperature icon appear or disappear from the display and the transmitter will emit a tone NOTE This feature must be active in the feature selection menu of your system Check with your installing dealer to insure this feature is set to the on position Light The Display ET Press and release the F Function button one time The display will illumi nate for 10 seconds Vibrate Or Tones E TOSS the F and unlock buttons simultaneously to toggle this feature on and off Daily Start Timer Only available on certain remote start units Press the option lock buttons simultaneously for 1 second The transmitter will beep and display the 24hr timer The vehicle will start 24 automatically when the time set is reached See chart for time settings Pressing this button combination a second time will toggle this feature off Note the transmitter must be within rang
3. Model XR9000 oe Owner s Manual Long Range Remote Start Security System With Plug In Shock Sensor amp Starter Disable IMPORTANT n order to provide you with the highest level of security to your vehicle this system is equipped with selectable manual override circuitry lt is that you will need to override you security system if the transmitter ecomes lost or inoperative due to battery failure Reading the sections on Manually Overriding Your System is necessary to fully understand the procedure required to enable your vehicle in such situations In addition the chart on the last page of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected Although the default mode is Valet Switch operation the system can be configured for Custom Code operation for enhanced security Confirm the override mode selected on last page of this manual and familiarize yourself with the section on it s ion FEATURES Mus ie 6 Button LCD Remote Control amp 1 One Way 5 Button Remote ontro Seven Channel Code Learning Programmable Receiver External Superheterodyne Transceiver Antenna Single Or Two User Programmable W Separate Control Outputs Single Button Lock Unlock or Separate Button Lock Unlock or Both Keyless Entry With Optional Access Guard must have power door ocks Selectable Manual Override Mode New Enhanced Pani
4. Timing Count Down H The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important Setting information shown on previous page Power Save Feature Press the F and Lock buttons simulta neously to toggle this feature on and off With this mode on the battery in the transmitter will go into a power down mode when the unit is disarmed 24 Hour Start Timer This icon is displayed when the 24 hour start 24 timer is activated Press the option lock buttons simultaneously for 3 second The transmitter will beep and display the 24hr timer The vehicle will start automatically when the time s t is reached See chart for time settings Pressing this button combination a second time will toggle this feature off Note the transmitter must be within range of the vehicle to set this feature and within range to cause the vehicle to start at the preset time The unit will start at th prescribed time once only This function must be selected each time you want the vehicle to start To activate this function a Turn the ignition switch off b Within 10 seconds of step a depress and hold the brake pedal while pressing the key icon transmitter button 2 times c the unit will emit 2 chirps the transmitter will beep and the start timer icon on the display will remain on Temperature Start Mode This icon will appear when the temp start mode is activated The vehicle will sta
5. exit the vehicle and close all doors hood lid and trunk lid 2 Press and release Lock Arm button on the keychain transmitter The dash mounted LED begins to flash slowly Parking Lights flash one time Siren sounds one chirp If the siren horn sounds 3 chirps then you have left a door trunk or di aaa T P hood lid ajar Simply close the opened entry point to provide full protec tion If the siren chirped three times sometime after arming the exclusive SEE A dome light learn circuit has been programmed and the system defected a open entry poini after the learned delay expired Again closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction If the siren horn did not sound when arming then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DIS ARM CHIRPS in this manual Doors Lock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when arming as an added convenience the system will turn on the headlights when the system is armed SILENT ARMING ACTIVE Must be activated during programming 1 Turn off the engine exit the vehicle and close all doors hood lid and trunk lid 2 Press ang hold the Lock Arm button on the keychain transmitter for 2 seconds The dash mounted LED begins to flash sl
6. return the vehicle to the valet off position This will ensure that the vehicle remains piolecte at all times MANUALLY OVERRIDING YOUR SYSTEM USING THE PBLED OVERRIDE SWITCH l Your Security System can be disarmed without the use of the keychain transmit ter This is necessary since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails If your system has been selected for Valet Switch manual override as indicated on the l st page of this manual to bypass the alarm system Page 6 128 7863 6 of 20 1 Open the vehicle door The alarm will sound 2 Turn the ignition key to the on position 3 Within 5 seconds press and release the PBLED override switch The alarm system will stop sounding and enter the bypassed mode You can now start and operate the vehicle normally Typically this override mode is used only if the transmitter has become inopera tive Programming Your Custom Override Code Unlike override switches easily found and defeated this security system allows the consumer to program a personal override code offering a higher level of security To take advantage of this option programmable feature 10 must be selected for the Custom Code Option Consult your installation center for pro gramming details The system comes from the factory with a pre programmed override code of 11 To change this default override code do the following 1 Disar
7. system Your Keeloq Code Hopping transmitters will change their signal every time the button is pressed so when a thief grabs then re transmits your signal the alarm system will not respond If your transmitter button is pressed more than fifty times while it is out of range of the vehicle children playing with your keys the transmitter will not operate when you return to the vehicle and will need to be re aligned to the receiver To do this Page 2 128 7863 2 of 20 simply press button 1 lock two times within a one second time period The system will now respond to that transmitter each time a button is pressed NOTE This system is custom configurable and can be set up to operate with a number of options controlled from any transmitter button or button com bination For reference we will describe operation assuming that your system is programmed for separate lock and unlock but tons Also reference will be made to the icons as shown on the buttons left NOTE The LCD based remote will be explained in detail further in this manual See System Status described later in this manual Consult your instal lation center if your system has been configured differently NOTE Your system has the option of using a siren the vehicle horn or both for the sounding device Where the siren is referenced below the horn or both may in fact chirp or beep ARMING THE SYSTEM ACTIVE 1 Turn off the engine
8. the shock sensor or an accessory trigger ing device that may have been added to the system If the LED is flashing two times pause two times pause etc then an intrusion attempt was made to a hood or trunk pin switch that was added to the system or to a light activated entry point if the alarm was installed using the voltage sensing feature If the LED is flashing three limes pause three times pause etc then an intrusion attempt was made through one of the vehicle s doors These intrusion warning indicators are stored in the system s memory and will only be erased when the ignition key is turned on PUSH BUTTON LED VALET OVERRIDE PROGRAMMING SWITCH PBLED he PBLED switch allows you to temporarily all alarm functions elimi nating the need to hand your transmitter to parking attendants or garage me chanics When the system is in valet mode all alarm functions are bypassed however the remote panic feature and remote door locks will remain operational To use the valet mode the system must first be disarmed either by using your keychain transmitter or by activating your personalized manual override code 1 Enter the vehicle and turn the ignition key to the on position 2 Press and hold the PBLED switch until the LED turns on solid The system will remain in the valet mode 3 To return to normal operation press and release the PBLED switch any time the ignition is on NOTE Always remember to
9. way to move the channel 3 function to a different transmitter button ADDITIONAL REMOTE FUNCTION CHANNEL 4 his system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are Can Be Set Up To Activate Rear Window Defogger During Remote Start If Vehicle Is So Equipped O Remote Window Closure O Rear Hatch Release L1 Right Or Left Slider Doors in An Equipped Van To activate the optional accessory press the option button on the keychain transmitter The optional accessory will immediately engage ADDITIONAL REMOTE FUNCTION CHANNEL 5 his system has an adaitional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are Remote Trunk Release O Remote Window Closure O Rear Hatch Release l L1 Right Or Left Slider Doors in An ES Van i To activate the optional accessory press the option button on the keychain transmitter The optional accessory will immediately engage ADDITIONAL REMOTE FUNCTION CHANNEL 6 his system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are O Rear Hatch Release mods O Right Or Left Slider Doors in An Equipped Van Driver Priority Settings In Vehicles So Equipped ar activate the optional accessory press the option button o
10. you to set the count down up 19 Hours and 59 Minutes from the current time and when the timer reaches zero the transmitter will emit a tone or vibrate dependent your preferred setting See chart for setting the count down time or this feature 00 Valet When the System is in the valet mode the icon shown will show in the display when the status check buttons are activated zZ am Parking Meter Counter The transmitter has a built in clock that can count down from 10 20 30 60 90 or 120 minutes This feature is useful when parking the vehicle in a metered parking lot If the time on the parking meter is 30 minutes you can set the count down timer to 20 minutes The transmitter will emit beep tone when the timer expires to remind you to get back to your vehicle See following chart for setting the parking meter count down timer feature Alarm Clock Mode The transmitter has a built in alarm clock that can be set to beep at a certain time each day The alarm clock mode must be set and the feature turned on To use this feature please refer to the chart on the following page i NOTE Your system is shipped with two transmitters 1 two way shown on the left and the one way transmitter shown right The one and two way transmitters are programmed from the factory with separate lock amp unlock buttons the trunk key icon button operates remote start and remote trunk release where applicable The option button and a
11. ETTINGS To Be Completed By Installing Technician Remote Start Function Door Lock Time 1 Sec 3 5 Sec 1 Sec L DbI UL Parking Lights Pulse teady Run Time 5 Min 10 Min 15 Min Remote Activation Chirp On ff Remote Alarm Function Transmitter Button s Channel 1 L Arm Disarm Disarm 2 Arm Only 1 Channel 2 ot Used Disarm Disarm 2 1 3 Auto Door Lock Auto Door Unlock Drivers Off Passive Lock Passive Arm Off Siren Horn iren amp Horn Siren Only Horn Only Horn Chirp 16mS 30mS Valet Coded Ovrride Chirp On The Fly Off Remote Trunk Release Channel 3 And Remote Start Remote Window Close Channel 4 5 6 oi Additional Option Channel 4 5 6 Additional Option Channel 4 5 6 or 7 Additional Option Aa M M Channel 4 5 6 or 7 2 Remote Garage Interface 2006 Audiovox Electronics 150 Marcus Blvd Hauppauge NY 11788 128 7863 7 r r r Page 20 128 7863 20 of 20
12. N TO SELECT TRANSMITTER FUNCTION OPERATION BUTTON ICON TONE VIBRATE 10 MIN PARKING COUNT DOWN TIMER Option 0 10 MELODY 20 MIN PARKING COUNT DOWN TIMER Option 0 20 MELODY 30 MIN PARKING COUNT DOWN TIMER Option 0 30 MELODY 60 MIN PARKING COUNT DOWN TIMER Option 1 00 MELODY 90 MIN PARKING COUNT DOWN TIMER Option 1 30 MELODY 120 MIN PARKING COUNT DOWN TIMER Option 2 00 MELODY PARKING COUNT DOWN TIMER OFF MODE Option 0 00 MELODY BACKLIGHT DISPLAY FOR 10 SECONDS ILLUMINATES DISPLAY VIBRATE TONE SELECT iut VIBRATE 4 TIMES ORBEEP 1X ALARM CLOCK MODE SELECT ON OFF Ot 18 88 MELODY FAHRENHEIT CELSIUS SELECT POWER SAVE MODE e 9 Forc MELODY MELODY Page 19 128 7863 19 of 20 XR9000 SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING PASSIVE ARMING ACTIVE REARMING SLOW FLASHING ARMED OFF DISARMED ON SOLID VALET MODE 3 FLASH PAUSE INTRUSION ZONE 3 2 FLASH PAUSE INTRUSION ZONE 2 1 FLASH PAUSE INTRUSION ZONE 1 SIREN CHIRP INDICATORS 1 CHIRP ARM 2 CHIRPS DISARM 3 CHIRPS ARM DOOR OPENED 4 CHIRPS DISARM INTRUSION PARKING LAMP INDICATORS 1 FLASH 2 FLASHES FEATURE AND FUNCTION S
13. ain transmitter by pressing and releasing the second channel transmitter button 2 times 2 Shut off the vehicle using the transmitter by pressing and releasing the second channel transmitter button 2 times 3 Within 10 seconds of step 2 activate the RF start command two times Push the second channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode 15 activated CANCELING THE AUTOMATIC START UP TIMER To cancel the automatic start up timer do one of the following 1 Start the vehicle manually with the use of the ignition key and depress the brake pedal 2 Remote start the vehicle using your keychain RF transmitter NOTE Option button used in combination is only available on the alternate remote transmitter and not available on the LCD Transmitter ADDITIONAL REMOTE FUNCTION CHANNEL 3 15 system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are L Remote Trunk Release O Remote Window Closure O Remote Garage Door Interface To activate the optional accessory press and hold the trunk key button on the keychain transmitter for four seconds Page 11 128 7863 11 of 20 NOTE The feature that has been added to channel 3 will always be activated using the same transmitter button that remotely starts the vehicle There is no
14. c Feature Any button other than unlock stops siren no change to the units state Smart Disarm If triggered elect to shut off siren or disarm entire unit Ause Shock Sensor Via The Transmitter Pre Detect Off Pre amp Full Detect Off City Mode rae Output Controlled From Channel 3 Option Channel 3 For Trunk Or or 24 Hour Time Start Mode Cold Temperature Start Mode 2 or 4 Hour Automatic Start Mode Parking Meter Count Down Timer On LCD Remote Additional Count Down Timer Mode Remote Panic In All Modes Press amp Hold Lock Unlock Button For 3 Seconds To Engage Improved Custom Code Override User Selectable and Programmable Protected PBLED Push Button LED Valet Program Manual Override Switch 7 Function LED Arm Disarm Zone 1 Zone 2 Zone 3 Valet Arming Intrusion Alert With Memory Instant Siren Activation Starter Disable Output 128 7863 1 of 20 Additional Engine Immobilizer Output Optional Relay Required True Last Door Arming Hardwire Only Defective Zone By Pass Defective Zone Chirp Confirmation Unit Chirps To Report Zone Cleared 6 Tone Mini Siren Car Horn Output For Additional Alarm Response Improved Timing To Minimize RF Interference Additional Negative Trigger Input Hood and Trunk RF Inhibit With Ignition On Parking Light Flasher Relay On Board Plug In Dual Stage Shock Sensor Pre detect Full Trigger and City Mode Au
15. dible Arm Disarm Defect and Tamper Chirp Indications Headlight Control Output Illuminated Entry Control Output Active or Passive Arming Selectable Programmable Auto Lock On Off Programmable Auto Unlock On Off Drivers Door All Doors aaa Door Lock Pulse Duration 1 Second 3 5 Seconds 1 Sec Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter Or Selectable Through Software Dome Delay Learn Circuitry Patented OPTIONS Telematic Upgrade Ready Plug In Flash Logic By Pass Capable Remote Trunk Release must have electric trunk release Remote Keyless Entry must have power door locks Multiple Vehicle Capable Remote Power Window Roll Up CAUTION Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous car bon monoxide fumes which can be harmful or fatal if prolonged expo sure occurs DO NOT remote start the vehicle if it is garaged YOUR CODE HOPPING TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current auto motive security system Some of togay sophisticated auto thieves use a device known as a code grabber which will receive and store the signal from your keychain transmitter and re transmit at a later time to disarm your
16. ditions exists 1 The Vehicle Hood Is Opened 2 The Gear Selector Is In Any Gear Other Then Park 3 The Brake Is Depressed 4 The System is in the Remote Start Override mode WARNING Be certain that the vehicle is outdoors before using this or any remote vehicle starting device A running engine produces dangerous carbon monoxide fumes which can be harmful or fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged To Remote Start The Vehicle Press and release the p ogrammed channel of your keychain transmitter two times within 2 seconds The vehicle will start and remain running for the pre programmed 5 10 15 or 20 minutes As a visual indication the parking lights will eee or turn on depending on the programming set up by your installation center When you arrive at your vehicle disarm the alarm system by pressing and releas ing the arm disarm button of your keychain transmitter Enter the vehicle and turn the ignition key to the on position CAUTION Do not turn the key to the start position This will cause the starter motor to engage with the already running engine which could result in damage Step on the brake pedal to disengage the remote start unit The vehicle will continue to run but now on it s own power NOTE The engine will stop running before the expiration of the pre programmed run timer if you complete any of the following 1 Press and release the programmed channel of you
17. e of the vehicle to set this feature and within range to cause the vehicle to start at the preset time The unit will start at the prescribed time once only This function must_be selected each time you want the vehicle to start To activate this function 9 Turn the ignition switch off b Within 10 seconds of step a depress and hold the brake pedal while pressing the key icon transmitter button 2 times c the unit will emit 2 chirps the transmitter will beep and the start timer icon on the display will remain on Note this feature must be activated at the vehicle at the prescribed time Once Page 16 128 7863 16 of 20 activated at the vehicle you can toggle the feature on simultaneously pressing the Lock Option buttons of the transmitter The 24 hour icon will appear and the transmitter will emit a tone confirming the feature is active 4 Note the unit will start once and run for the prescribed time If you require more starting please refer to auto start up timer mode shown earlier in this uide OTE To insure accurate 24 Hour Start up it is advisable to reset the start time pened as time may drift slightly each day iming Count Down The unit offers an additional count down timer for situations where an alert tone may be needed to remind you of something important For instance you may have a meeting 4 hours from now and you want a reminder in 3 Hrs and 45 Mins This additional count down timer allows
18. e to repeat steps 1 through 7 above being certain to note the following Acceptable digits 10ths or units are 1 through 9 The unit will not recognize a 0 Zero or no digit entered any place units tenths 15 seconds of inactivity expire or if the ignition switch is turned off for more then 5 seconds during any of the above steps the unit will revert back to the last successfully stored code MANUALLY OVERRIDING YOUR SYSTEM USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed and the default override code of 11 is in the system s memory 1 Enter the vehicle and turn the ignition switch to the on position OTE The siren will sound 2 Within 5 seconds press and release the PBLED switch 1 time 3 Within 5 seconds turn the ignition switch off then on 4 Within 5 seconds press and release the PBLED switch 1 time 5 Turn the ignition switch off then on and start the vehicle If you have changed programmed override code then substitute your new code tenths for step 2 above and units for step 5 above ELIMINATING THE NORMAL ARM DISARM CHIRPS i You can selectively eliminate the normal arm amp disarm chirps by holding the transmitter button slightly longer when arming or disarming This will prevent the siren chirps for one arm or disarm cycle If you find this inconvenient and wish to eliminate these chirps permanently 1 Turn the ignitio
19. for the full 30 second alarm cycle NOTE _ If the optional interior illumination circuit was installed the interior light will flash as well for the full 30 second alarm cycle DISARMING THE SYSTEM NOTE If the optional 2 step door unlock circuit is installed when the unlock Page4 128 7863 4 of 20 transmitter button is activated the drivers door only will unlock pressing the unlock button a second time will cause all doors to unlock NOTE If your transmitter has been configured with single button Lock Unlock to activate the all door unlock feature operate the Lock Unlock button a second time within 3 seconds of the first unlock command 1 As you approach the vehicle press and release the Unlock Disarm button on the keychain transmitter The dash mounted LED turns off The LED will start flashing rapidly indicating that the system is re arming automatically Open any door to suspend the automatic arming Parking Lights flash two times If the parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify which zone was triggered Siren sounds two chirps If the siren sounds 4 chirps then the alarm was triggered in your absence Before turning the key on examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered If the siren did not sound when disarmi
20. from the transmitter If the system has been such Page 9 128 7863 9 of 20 programmed simply press the lock button of your keychain transmitter anytime during the remote start cycle The shock sensor will be shunted for the entire run cycle and will resume normal operation after the remote start unit shuts off Check with your installation center to determine if this feature has been pro grammed into your system PBLED SAFETY CONTROL SWITCH The Push Button LED control switch allows you to temporarily disable the remote starting function of the system This recommended whenever the vehicle is being serviced To place the system in the service mode 1 With the system disarmed unlocked and the ignition switch off Press and old the PBLED on 2 Turn the ignition switch on off on off on off 3 The LED begins to flash two short flashes followed by one long flashes and continues this pattern until returned to normal mode of operation This puts the unit into the R S Override mode pee at the remote start is in the service mode and will not start from RF or any other input Posse or otherwise To Exit R S Override Mode 1 With the system disarmed Press and Hold the PBLED on 2 Turn the ignition switch on off on off on off 3 The LED turns off indicating that the R S unit is fully functional one again EMOTE STARTING THE VEHICLE Ine Sem WILL NOT start the vehicle if any one of the following con
21. ibration occurs the siren will sound 3 Stage 2 Omit pre amp full detect In this mode both the pre detect stage and the full trigger stage of the sensor are defeated The unit will not react to vibration of any magnitude NOTE Shock Sensor Icon Is Displayed On The LCD Panel 4 Stage 3 City Mode In this mode the pre detect chirps will change from six pre warning tones to a full 10 seconds of warning chirps The full detect trigger duration will be reduced from 30 seconds to 15 seconds NOTE Setting the stage of the shock sensor will be effective for one arming cycle only Once the system has been disarmed the very next arming cycle will cause the sensor to default to the normal operation stage To change or adjust the shock sensor press and release the ARM button of you keychain transmitter 1 Within 2 seconds of arming press and release the ARM button 1 time to defeat the pre detect stage of the shock sensor The lights will flash and the siren will chirp once 2 Within 2 seconds of step 1 press and release the ARM button 2 times to defeat the pre and full detect stages of the shock sensor The lights will flash and the siren will chirp twice 3 Within 2 seconds of step 1 press and release the ARM button 3 times to enter the City Mode of operation The lights will flash and the siren will chirp three times While under control of the remote start the system can be programmed to allow you to shunt the shock sensor
22. itled ELIMINATING THE ARM DISARM CHIRPS in this manual Doors Lock Optional Door locking during passive arming is a selectable feature The alarm can be programmed to allow the doors to lock only when arming using the keychain transmitter and they will not automatically lock during passive arming PROTECTION WHILE THE SYSTEM IS ARMED Opening any gs door hood or trunk lid will cause the alarm to imme diately sound The alarm will continue to sound for 30 seconds then stop and continue to monitor all protected entry points If the thief left a door opened the alarm will sound for six 30 second cycles remain armed and ignore that trig gered zone Whenever the system is armed the dash mounted LED indicator will slowly flash This serves as a visual deterrent to the potential thief The LED is a ver low current bulb and will not cause the vehicle s battery to drain even when left unattended for extended periods Whenever the system is triggered the vehicle s parking lights will flash for the full 30 second alarm cycle attracting visual attention to the vehicle Optional Whenever the system is armed the vehicle s starting circuit will be Mecca If the thief should choose to ignore the siren the vehicle can not be started Any mild impact to the vehicle s glass will cause the alarm to sound a short series of warning tones Any strong impact to the vehicle s glass will cause the alarm to trigger
23. l flash_unlock icon will be displayed and the siren will beep on the LCD screen When ever the vehicle is operated from the two way transmitter the unit will beep responsive to the function executed at the vehicle 1 beep when armed 2 beeps when disarmed etc at times It may be inconvenient or too noisy to hear the beep tones so the system allows you 808 to sot he uni toggle on 9 off beep tones vibrate Simultaneously press the asl S F and unlock buttons The icons Shown left will M appear in the upper left hand corner of the screen to indicate vibrate If the alarm system has been triggered the icon displayed on the transmitter sound the beep tones or vibrate dependent upon the setting as shown above The following trigger patterns will be displayed f LCD will indicate which zone has been activated as well Triggered and the entry attempt was made to one of the vehicle Doors Triggered and entry attempt was made to the vehicles Hood Or Trunk Triggered and entry attempt was made to the vehicles glass or the vehicle has been hit or bumped hard enough to cause a response from the vibration detector ADDITIONAL ICONS THAT MAY BE DISPLAYED ARE If the arm disarm chirp tones have been turned off at the ve hicle when you arm or disarm the display will indicate this as shown and there will be no arm disa
24. m the system by use of the transmitter or by use of the emergency override sequence Turn the ignition switch_to the on position Within 10 seconds press and release the PBLED switch 3 times Within 10 seconds turn the ignition switch off on off on off on The siren or horn will and the lights will flash one time Within 10 seconds begin to enter your chosen 10ths digit by pressing and releasing the PBLED switch from 10 to 9 times Hen MU 10 seconds of the last entered 10ths digit turn the ignition switch off en on Within 10 seconds begin to enter your chosen units digit by pressing and releasing the PBLED switch from 1 up to 9 times 7 Finish by turning the ignition switch to the off position If the new code was accepted the unit will report back the newly entered code by flashing the LED first indicating the 10ths digit pause and then the units digit The unit will report the new code three times with a one second pause between each code then the system will begin arming If the LED flash pattern reports the previously stored code the new code was not entered correctly Please repeat Steps 1 through 7 above considering the following NOTE Acceptable digits 10ths or units are 1 through 9 The unit will not recog nize a 0 Zero or no digit entered in any lace units or tenths NOTE If 15 seconds of inac Ivity expire or if the ignition switch is turned off for more then 5 seconds auring an
25. n the keychain transmitter The optional accessory will immedi atel engage ADDITI L REMOTE FUNCTION CHANNEL 7 his system has an additional feature that can be connected to a number of different optional accessories Some of the more common uses for this channel are Rear Hatch Release O Right Or Left Slider Doors in An Equipped Van O Driver Priority Settings In Vehicles So Equipped O Second Driver PRO Springs In Vehicles So Equipped To activate the optional accessory press the option button on the keychain transmitter The optional accessory will immediately engage Note If your system utilizes the transmitter shown the second option button may be configured to operate additional accessories Please consult your installing retailer for more information concerning the options available IURBO TIMER MODE his system provides a means to cool down the vehicles turbo charger if so equipped by allowing the vehicle to continue to run for a prescribed period of time every time the vehicle s engine is turned off This teature requires the System to be set up for turbo timer during installation Consult with your installa tion center to be certain this feature was activated and how long the vehicle will continue to run 3 5 or 10 minutes after the ignition switch is turned off To activate the turbo timer Anytime the ignition key is in the on position for more than 15 seconds Page 12 128 7863 12 of 20
26. n switch then of 3 Within 10 seconds of turning off the ignition press and release the PBLED switch 3 times j 4 the chirps were on before you started the siren will emit 2 short chirps indicating that the chirps are now off If the chirps were off before you started the siren will emit one short chirp indicating that the chirps are now on NOTE If vehicle battery is disconnected then reconnected the unit will re turn to the default setting of chirps on Repeat the above procedure to eliminate the arm disarm chirps NOTE Whenever the chirps are bypassed the 4 chirp intrusion indicator and 3 chirp defective zone indicator will always operate Since these are warnings to you that something has happened they cannot be eliminated NOTE Your system must be programmed by the installation center to en able this feature REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations To use remote panic 1 Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds The alarm will immediately sound 2 To stop the alarm press and hold the Lock or Unlock button on the transmitter Page 8 128 7863 8 of 20 again for 3 seconds If the button is not pressed the alarm will automatically stop after 30 seconds Also if any transmitter button other than the L
27. ng then the chirps have been turned off and you should refer to the section titled ELIMINATING THE ARM DISARM CHIRPS in this manual O Doors Unlock Optional 2 Step Doors Unlock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when disarming as an added convenience the system will turn on the headlights when the system is disarmed SILENT DISARMING Must be activated during programming Note If the optional 2 step door unlock circuit is installed when the unlock transmitter button is activated the drivers door only will unlock pressing the unlock button a second time will cause all doors to unlock NOTE If your transmitter has been configured with single button Lock Unlock as shown to activate the all door unlock feature operate the Lock Unlock button a second time within 3 seconds of the first unlock command 1 Press and hold button the Unlock Disarm button on the keychain transmitter for 2 seconds The dash mounted LED turns off The LED will start flashing rapidly indicating that the system is re arming automatically Open any door to suspend the automatic arming Parking Lights flash two times If the parking lights flashed three times then the alarm was triggered in your absence Before turning the key on examine the LED to identify which zone was triggered Siren will not sound If the siren sounds 4 chirps then the alarm
28. ny button combina tion may be programmed to operate various options Consult your installation center for button programming and options that may have been added to your vehicle 3 Although this is the default programming from the factory this can be changed for you to any configuration you prefer Please refer to the transmitter program uides included with your kit OTE A maximum of two of either style transmitter may be pro grammed to your unit Page 17 128 7863 17 of 20 Battery Indicator Your transmitter has a battery indicator that is shown in m the upper right corner of the screen as shown left This icon indicates a new battery shown with 3 bars As the Pa deteriorates the bars will disap pear 1 bar indicates the battery should be replaced Replace battery with a resh 1 5V AAA battery and dispose of the used battery properly Other icons that will be displayed at times when certain functions and features are active in the vehicle or on the remote e Range Indicator The range indicator will have bars to the side of the icon if the unit is out of range Vibrate Mode On this icon will be displayed if you select vibrate instead of tones To toggle vibrate on and off press F Unlock simultaneously Alarm Clock This icon will be toggled on and off when the Trunk Key buttons are pressed simultaneously The feature must be set in the feature selection menu of the transmitter
29. ock or Unlock button is pressed and released the Panic mode will be turned off immediately The normal function of this transmitter button will be suspended during the Panic sounding period 3 During the panic mode the Lock and Unlock buttons can be used to lock and unlock the doors if the option is sten however once the unlock disarm button is pressed the vehicle s starter inhibit device where installed will be disabled allowing the vehicle to start NOTE While in the Panic mode pressing and releasing the Lock or Un lock buttons will if the option is installed lock and unlock the doors respectively While in the panic mode anytime the Unlock button is pressed the panic feature will continue for the allotted 30 seconds however the security system will be disarmed allowing the vehicle to start RF SHOCK SENSOR MODE SELECTION The way in which your alarm system reacts to threatening vibrations created by attempts to enter the vehicle by breaking a window is adjustable by the transmitter immediately after arming There are 4 modes of operation that can be selected by the operator 1 Normal Operation default mode In this mode any strong vibrations will cause the siren to sound full detect for 30 seconds Any lesser vibration will cause the siren to emit about 6 short warn away chirps pre detect 2 Stage 1 Omit pre detect In this mode the warn away chirps created by the lesser vibration will be deleted If strong v
30. of your vehicle TRANSCEIVER ICONS AND THEIR INDICATIONS When Disarmed Press the Arm Lock button to Lock and Arm the System The Lock Icon is displayed on the LCD panel amp the parking lights flash once When Armed Press the Disarm Unlock button to Unlock and Disarm the System The Unlock Icon is displayed onthe LCD panel amp the parking lights flash twice When the Key Icon Button Has Been Operated for 3 seconds the trunk open icon will flash on the LED Screen If text mode was selected the words Trunk Open will appear and remain on the screen until the trunk is shut When the Koy Icon Button is pressed 2 times in succession S The three puffs of smoke are displayed on the LCD screen while the vehicle is running The exhaust indication will flash and the hour glass will indicate count down timer based on the 5 10 15 or 20 minute run time set up by your installation cen ter When the unit shuts off the exhaust indication will turn off and the transmitter will play a melody Engine can be started in many modes armed disarmed Trunk valet etc The screen shown is Locked Armed and running Trunk Page 13 128 7863 13 of 20 When the Panic Mode has been activated and the system is armed the vehicle s lights will flash the siren and lock icon will be displayed on the LCD screen and the siren will beep If the system is disarmed and the Panic Mode is activated the lights wil
31. owly Parking Lights flash one time Siren will not sound If the siren chirped three times sometime after arming the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired Closing the hood trunk or doors will correct the problem and you do not need to disarm the system to make the correction Page3 128 7863 3 of 20 Doors Lock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when arming as an added convenience the sys tem will turn on the headlights when the system is armed The LCD Remote has the following response ARMING THE SYSTEM PASSIVE AUTOMATIC Must be activated during programming 1 Tumi off the engine exit the vehicle and close and lock all doors hood lid and runk lid The dash mounted LED begins to flash rapidly indicating 30 second passive arming has begun 2 Opening any protected entry point during the 30 second passive arming cycle will immediately suspend automatic arming and the 30 second passive arm ing cycle will re start when all doors are closed At the end of the passive arming cycle The dash mounted LED begins to flash slowly Parking Lights flash one time Siren sounds one chirp If the siren did not sound when arming then the chirps have been turned off and you should refer to the section t
32. r keychain transmitter two times within 2 seconds Page 10 128 7863 10 of 20 2 Depress the brake pedal 3 Open the hood 4 Place the system in the Remote Start Override mode 5 Race the engine to above 4000 RPM OPERATING ON AUTOMATIC START UP TIMER MODE Your system has the ability to automatically start the vehicle every 2 or 4 hours over a 48 hour period This feature is especially useful in cold climates where the only means to keep the engine and engine fluids warm is to periodically start the engine WARNING Be certain that the vehicle is outdoors before using this or any re mote vehicle starting device A running engine produces carbon monoxide fumes which be harmful fatal if prolonged exposure occurs DO NOT remote start the vehicle if it is garaged TO BEGIN THE AUTOMATIC START UP TIMER 1 Turn the ignition key on then off 2 Within 10 seconds activate the RF start command two times or the programmed channel button of your keychain transmitter 4 times The parking lights will flash and the siren will chirp 4 times indicating the timed start mode 15 activated The vehicle on a 2 or 4 hour interval basis will automatically start run for the pre programmed time 5 10 15 or 20 minutes and then shut off This will continue for 48 hours NOTE The automatic start up timer can also be initiated from the keychain transmitter To do this 1 Start the vehicle using the keych
33. rm chirps at the transmit ter This is true if the transmitter is set for vibrate mode When the vehicle is armed and a door is opened or ajar the transmitter will chirp 3 times the lights will flash and the display will indicate a door trigger as shown on the previous page When Page 14 128 7863 14 of 20 the door is closed or the zone clears the transmitter will chirp 1 time and the display will clear When the vehicle is armed and the hood or trunk is opened or ajar the transmitter will chirp 3 times the lights will flash and the display will indicate a hood or trunk trigger as shown on the previous page When the hood or trunk is closed or the zone clears the transmit ter will chirp 1 time and the display will clear Page 15 128 7863 15 of 20 ADDITIONAL REMOTE FEATURES The two way remote control unit allows you to access status information from the vehicle check temperature light the display toggle the transmitter from beep tones to vibrate mode initiate daily start timer and temperature start Selection of 144 these and other features are shown below NOTE Transmitter must be within operating range of the vehicle approximately 1000 ft 3 Check Vehicle Status Press the lock key option buttons simultaneously for 1 second The vehicle s alarm will display the systems current status
34. rt one time automatically when the temperature reaches 0 Caution Be certain vehicle is outside before activating this mode To toggle this feature on of off from the Locked Armed mode press the Option and Lock buttons simulta neously Available on certain remote start models only Throughout this manual you will find screen shots where they apply if using the two way transmitter If using the one way transmitter while the two way anemer is within range of the vehicle the two way transmitter will update it s screen Page 18 128 7863 18 of 20 TRANSMITTER FUNCTION SELECTION BUTTON ICON TONE VIBRATE TIMING ADJUST MODE HRS PRESS FOR 5 SECONDS ou 1 8 88 2 BEEP TONES TIMING ADJUST MODE MINS 1X 18 88 ALARM CLOCK ADJUST MODE HRS 2X 18 88 ALARM CLOCK ADJUST MODE MINS 3X ow 1 8 88 ALARM CLOCK amp POWER UP MUSIC SELECT 4X 8 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTON TO SELECT ALARM CLOCK ADJUST MODE ON OFF 5X 9 ON OFF TIMING COUNT DOWN ADJUST MODE HRS 6x 18 88 TIMING COUNT DOWN ADJUST MODE MINS 7X 18 88 TIMING COUNT DOWN END MELODY SELECTION 8X 8 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTON TO SELECT TIMING COUNT DOWN MODE SELECT ON OFF 9x ON OFF REMOTE START ON MELODY SELECT 2 5 8 5 SELECTIONS PRESS KEY BUTTON OR OPTION BUTTO
35. was triggered in your absence Before turning the key on examine the LED and refer to the INTRUSION Page5 128 7863 5 of 20 WARNING SIGNALS section of this manual to identify which zone was triggered O Doors Unlock Optional 2 Step Doors Unlock Optional NOTE If the optional Headlamp illumination feature has been added and has been selected for operation when disarming as an added convenience the system will turn on the headlights when the system is disarmed WHILE THE SYSTEM IS SOUNDING If during a triggered state you wish to shut off the siren without disarming your security system simply DES and release any transmitter button other than the Unlock Disarm button This action will turn off the siren yet leave the vehicle fully armed and protected This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security In this case you can cancel the siren sounding without disarming your alarm INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle If an intrusion attempt has occurred the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system Enter the vehicle and observe the red dash mounted LED to identify which zone was triggered 9 If the LED is flashing one time pause one time pause etc then an intrusion attempt was made to
36. y of the above steps the unit will revert back to the last successfully stored code Custom Code Programming Example i Change the code from the factory pre assigned code of 11 to 52 you would do the following 1 Disarm the system by use of the transmitter or by use of the emergency override sequence 2 Turn the ignition switch to the on position 3 Within 10 seconds press and release the PBLED switch 3 times 4 Within 10 seconds turn the ignition switch off on off on off on The siren or horn will beep and the lights will flash one time 5 Within 10 seconds begin to press and release the PBLED switch to set the cone d it As per the example press and release 5 times to set the tenths igit to ithin 10 seconds of the last press of the pushbutton turn the ignition switch off en 7 tnm 10 seconds begin to press and release the PBLED switch to set the units igit Page 7 128 7863 7 of 20 As per the example pe and release 2 times to set the units digit to ab 8 P the ignition switch to the off position Immediately observe the LED flash pattern You will note the LED Ld five times pause and then flash two times pause This pattern will be repeated three times indicating the new code 52 has been accepted and Stored in memory l NOTE If after step 7 the LED flashes a code other than what was just entered this indicates that the code has not been changed You will hav
Download Pdf Manuals
Related Search