elan-4tn preamp user`s manual
Contents
1. Functions ELAN 4TN PREAMP USER S MANUAL 4Band EQ with FND Tuner 4 5 6 7 MIDD TREB BASS PRES 6 Treble 7 Presence 8 Volume Knob 9 Low Batt Low Battery LED Light 10 Note Button 1 Tuner LED Display 2 Tuner FND Display 3 Tuner Button 4 Bass 5 Middle 1 3 Tuner Button for Power on off Button The tuner will work with or without a cable plugged into the output jack Bass EQ TONE CONTROL for bass tones Middle EQ TONE CONTROL for middle tones Treble EQ TONE CONTROL for high tones Presence EQ TONE CONTROL for very high tones The BASS MIDDLE TREBLE and PRESENCE controls are a 4 band equalizer for controlling tone The BASS TREBLE and PRESENCE tone controls are normal boost cut shelving controls The MIDDLE midrange tone control is a normal boost cut tone filter The center detent on these tone controls yields a flat tone response 12 boosts the tone 12 cuts the tone NO oo ff 8 Volume Knob The VOLUME controls the output volume Turned fully counter clockwise it is completely OFF Turned fully clockwise it is LOUD 9 Low Batt Low Battery LED Light The LED will light when the battery has lost power Replace the battery when this light is on This LED light will flash when a cable is connected to the output jack of the pickup system This shows the battery is good2. 10 Note Button Battery A 9 volt battery powers the ELAN 4TN preamp Before connecting the instrument to an amplifier or mixer please check that a fully charged 9 volt battery is connected Tuner Operation Tuner LED Display O C C H Tuner FND Display gt E i Tuner LED Display bO Tuning Guide LED for Sharp tune Tuning Guide LED for right tune Tuning Guide LED for flat tune Tuner Display The tuner will work with or without a cable plugged into the output jack Pushing the tuner button turns ON the tuner When the tuner is active the output signal is muted No sound will go to the amplifier or mixer when the tuner is active Pushing the tuner button again turns the tuner OFF and the output signal will be active and sound will go to the amplifier If the tuner is ON and the tuner button is not pushed within 2 minutes the tuner will turn OFF automatically and sound returned to the output The tuner Note Readout FND Display shows the nearest note of one plucked string s sound The Note Read Display read out shows twelve note possibilities in half steps in sharps for example A A B C C D D and so on For flat notes for example Bb B flat use A For Eb E flat use D Specification Features 4Band EQ with FND Tuner Input Impedance 2 2MQ Frequency Response 20Hz 20KHz Control Range Bass 12dB at 80Hz Middle 12dB at 800Hz Treble 4
3. 12dB at 3KHz Presence 12dB at 15KHz Tuner Function Auto Chromatic Turning Current Drop 12mA Power Supply 9V Alkaline Battery Low Battery Check LED Pick up Piezo ceramic pick up Output Jack 6 35mm 1 4 Dimension W 56mm X H 74 mm 2 2 X 2 9 Caution The jack should be pluged for proper Preamp working TUNER will works regardless pluging jack There is no output sound please check if tuner or mute is turned on When LCD screen is dim or no display please check battery life To prevent battery loss please unplug jack when preamp is not in use Do not disassemble for repair Return to your dealer for service or repair Do not use too much force when operating the control Beleal BELCAT Co Ltd Tel 86 752 355 7545 Fax 86 752 355 2460 Email belcat belcat com Internet www belcat com ROHS X ce This product complies with the RoHS directive E INSTALLATION MANUAL 1 Contents O C 2 Battery 3 Pick Up Box e o I oh 1 Preamp 4 Output Jack g 6 Screw 2 Tool 4 Router and Grinder cutting edge 3mm 1 Electric Drill fs me i 2 Drill Bit 5 Round File 2 3mm or 3mm 3 Phillips Screwdriver 6 Masking Tape 1 Cut out the hole with template Cutting Masking Template Tape Cutting Template 3 Drilling hole for Jack Masking Wa 5 Insert EQ and battery box into hole of guitar 6 F
4. asten screws properly 5 Put plugs into jacks 7 Installing the pick up 8 Fix wire with clip EQ peal Clip Out put jack LIN x Cable i Battery box Solution 1 When there is no sound or sound is stopped Check guitar cable amp or Mixer Check if there is batter or not When it happens noise or distortion please exchange battery Check if the pickup and battery connector is connected correctly or not Check if out put jack is connected correctly 2 When there is hum noise Check the pickup is connected well or not Check if the connectors are connected to correct position well or not 3 Some causes of the balance problem When the bottom of saddle or the groove of saddle is not flat When saddle is installed to the groove of saddle loosly When the connection is not good between the bottom of saddle and the groove of saddle When Saddle is very short When there is grounds on the groove of saddle When Saddle is declined toward front or back When the top of guitar is bended When the pickup is installed to only a part of the groove of saddle back page
Download Pdf Manuals
Related Search