Owner`s Manual (General)
Contents
1. reaches the Full line on the back 3 Check the pre motor filter at least once a month and clean and replace as needed 4 Check and replace the HEPA media post motor filter as needed NOTE More frequent filter cleaning may be necessary if you are vacuuming new carpet fine dust or have allergy concerns Follow the instructions on the following pages to perform these simple maintenance steps pissell 8 www bissell com 4 NOTICE While vacuuming certain carpets and low humidity conditions may generate small static discharges The discharges are entirely harmless and are not associated in any way with the main power supply To reduce the risk of electric shock turn power switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks For maximum cleaning performance check and clean or replace all filters as suggested 800 237 7691 2 Carrying Handle Maintenance and care Emptying the dirt container The dirt container needs to be emptied when the dirt reaches the Full line on the back of the container 1 Press the release button on the top of the carrying handle to remove the dirt container 2 Hold the dirt container over trash can and push the emptying button to open the bottom Close the dirt container door when empty 3 Replace dirt container on cleaner by align ing the bottom and pushing forward until it snaps2. ET saturday 9 a m 8 p m ET Or visit our Website www bissell com Item Part No Part Name 1 203 2050 Style 20 Drive Belt 2 Pack 2 203 2011 Twist n Snap Hose and Handle 3 203 2054 Brush Roll Grey 4 203 2091 Style 20 Pre Motor Filter 5 203 2093 style 20 HEPA Media Post Motor Filter 6 203 2097 Inner Cyclone Assembly 2 3 4 OO ERE Additional accessories These items are available for purchase as accessories for your BISSELL PROlite Multi Cyclonic To purchase call 1 800 237 7691 or visit www bissell com ltem 1 OORA W PO 1 g 4 ot Part No Part Name 203 2002 Crevice Tool 203 1429 TurboBrushe 203 2001 Dusting Brush 203 2003 Extension Wand 203 2004 Deluxe Floor Tool 203 2006 Bendable Wand Attachment A www bissell com E 800 237 7691 15 16 Warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail telephone or regular mail as described below Limited Five Year Warranty subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Homecare Inc will repair or replace with new or remanufactured components or products at BISSELL S option free of charge from the date of purchase by the original purchaser for five
3. OFF 1 Make sure brush switch is pushed ON 2 Vacuum is in upright position 2 Recline vacuum to operate brush 3 Brush is jammed 3 Remove obstruction or debris unplug cleaner and reset brush pages 11 amp 12 4 Brush needs to be reset 4 Unplug cleaner to reset brush page 11 5 Handle not fully attached 5 Remove handle and reinstall Vacuum cleaner won t pick up or low suction Possible causes Remedies 1 Hose wand not properly positioned 1 Make sure hose wand is fully seated in base 2 Dirt container not installed properly 2 Correctly position and snap into place 3 Dirt container full 3 Empty dirt container 4 Clog in cleaner 4 Follow instructions on page 11 5 Filters are dirty 5 Check and clean foam filter check and replace HEPA media filter cartridge if needed 6 Hose not properly attached 6 Check Twist n Snap hose connection and make sure hose is securely in hose base Visible dirt escaping from cleaner Possible causes Remedies 1 Dirt container full 1 Empty dirt container 2 Filters or inner cyclone missing or installed incorrectly 2 Check inner cyclone pre motor and post motor filters for correct installation 3 Dirt container not installed properly 3 Make sure dirt container is correctly postioned and snapped into place Hose not installed properly 4 Make sure hose wand is fully seated in base 5 Hole or crack in hose 5 Check hose for holes or cracks and replace as needed Bissell www bissell co
4. WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE FIVE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Bissell 2009 BISSELL Homecare Inc Grand Rapids Michigan All rights reserved Printed in Korea Part Number 110 4164 Rev 10 09 Visit our website at www bissell com 800 237 7691 1 Bissell www bissell com
5. areas If any damage is present discard old drive belt and replace A qv 10 www bissell com an Air Passageway c6 937 7691 Maintenance and care Rotating brush and drive belt maintenance continued 9 Place one end of the drive belt over motor pulley and the other end over the brush in the space between the bristles Ensure the grooves on the belt line up with the grooves on the motor pulley and the brush 10 Push the belt side of the brush down into the slots on the side and then push the non belt side into the slots 11 Reposition brush cover and screws Tighten screws securely 12 Plug in vacuum and make sure motor turns on Brush reset The brush power switch will blink 5 times and the motor will shut off if the rotating brush is jammed To reset the brush turn the cleaner off and unplug from the outlet Remove the obstruction The brush will automatically reset when the cleaner is plugged in and turned back on Cleaning clogs Low suction or poor pickup may be due to a clog in the vacuum cleaner If you notice a change in the sound of the motor or a reduction in the spinning action check for clogs 1 Unplug cleaner from electrical outlet Suction Opening Empty dirt container 2 3 Check Tank for build up or clogs 4 Remove the inner cyclone and check suction inlets for a clog 5 Grasp the hose handle and lift to separate from the suction opening Check for a clog in the
6. years any defective or malfunctioning part see information below on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the User s Guide is not covered If your BISSELL product should require service Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services Website or E mail Or Call Or write www bissell com BISSELL Consumer Services BISSELL Homecare Inc Use the Customer Services tab 1 800 237 7691 PO Box 3606 Monday Friday 8 a m 10 p m ET Grand Rapids MI 49501 Saturday 9 a m 8 p m ET ATTN Consumer Services BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS
7. PRO E lit BISSEl ILC EN USER S GUIDE 17G5 SERIES 3 Safety Instructions 4 Product View 5 Assembly 6 8 Operations 8 12 Maintenance and Care 13 Troubleshooting 14 Consumer Services 15 Replacement Parts 15 Additional Accessories i 1 Sm wi PRO Ee pA E R am L 16 Warranty a AUTO HEIGHT ADJUST Part 110 4164 2 Thank you for buying a BISSELL PROlite Multi Cyclonic vacuum We re glad you purchased a BISSELL vacuum Everything we know about floor care went into the design and construction of this complete high tech home cleaning system By purchasing this product you are helping BISSELL with our commitment to reducing our impact on the environment through an expanding range of sustainable design efforts Your carpet cleaner is well made and we back it with a limited five year warranty We also stand behind it with a knowledgeable dedicated Consumer Services depart ment so should you ever have a problem you ll receive fast considerate assistance My great granafather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your carpet cleaner Thanks again from all of us at BISSELL err d Sero Mark J Bissell President and Chief Executive Officer Bissell www bissell com 800 237 769 www bissell com IMPORTANT SAFETY INSTRUCTIONS When using
8. an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM Always connect to a polarized outlet left slot is wider than right Unplug from outlet when not in use and before conducting maintenance AN WARNING ro reduce the risk of fire electric shock or injury ll Do not modify the polarized plug to fit a non polarized outlet or extension cord lll Do not leave vacuum cleaner unattended when it is plugged in ll Unplug from outlet when not in use and before servicing W Do not use outdoors or on wet surfaces ll Do not allow children to operate vacuum cleaner or use as a toy lll Close attention is necessary when used by or near children ll Do not use for any purpose other than described in this User s Guide lll Use only manufacturer s recommended attachments lll Do not use with damaged cord or plug ll f appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized service center ll Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces lll Do not unplug by pulling on cord To unplug grasp the plug not the cord lll Do not handle vacuum cleaner or plug with wet hands ll Do not put any object into openi
9. base or the hose To remove clogs from the hose base 6 Recline handle and turn vacuum cleaner over so bottom side is up Locate and turn the quick release tabs on the foot hose cover as shown and pivot the cover out to remove 7 Pull foot hose straight up to remove from foot base Turn the vacuum back over straighten the foot hose and unclog with a long narrow object such as a broomstick uo 1 1 www bissell com p Y 800 237 7691 12 Maintenance and care Cleaning clogs continued To remove clogs from the hose 8 Release the Twist n Snap hose from the vacuum by turning to the left Straighten the hose and unclog with a long narrow object such as a broomstick 9 Ifthe low suction persists follow the instructions for Checking the Rotating Brush on page 10 and inspect the air passageway for obstructions TurboBrush maintenance The TurboBrush should be checked regularly for clogs or debris wrapping around the brush 1 Twist collar so opening is at the top and lift top cover to remove 2 hemove the brush from the belt and clean debris 3 Replace the brush inside the belt and place ends into slots on sides as shown 4 Reposition top cover making sure to line up inside tab at the front with the opening on the cover Twist collar until opening is at the bottom to lock into place Electronic protector An internal electronic protector has been designed into your cleaner to protect it from over
10. d electrician to install a proper outlet Do not change the plug in any way This model is for household use only 800 237 7691 3 Product view Power Switch Handle a 1 Brush On Off Switch gt Cord Clip b od Bendable A Wand Attachment Quick Release Cord Wrap otretch Hose Hose Clip Tuisi n 8 Release Button wist n Snap Hose t Connection Carm Hose Handle Handle screen Inner Cyclone Handle Release Pedal Hose Base Foot Hose Filter Housing HEPA Media amp Post Motor Filter Inside Brush AUTO HEIGHT ADJUST Automatic Height Peron sien Guard Do not plug in your vacuum cleaner until you are familiar with all instructions and operating procedures 4 Bissell www bissell com AED 800 237 769 Assembly The only tool you ll need to assemble your vacuum cleaner is a Philips head screwdriver AN W ARN N G u Remove handle and tools from box Plastic film can be dangerous To avoid danger of suffocation keep away from babies and children 1 Locate and remove the deluxe floor tool extension wand bendable wand attachment dusting brush TurboBrush crevice tool and accessory bag from box 2 Locate and remove vacuum handle and Twist n Snap Hose and set aside 3 Lift vacuum body out of box using carrying handle on dirt container Attach handle to vacuum 1 Take vacuum handle and remove the screw packet taped to
11. heating When the electronic protector activates both power buttons will flash continuously and the cleaner will stop working If this happens proceed as follows 1 Turn the cleaner OFF by pressing the power switch and unplug from electrical outlet 2 Check the inner cyclone area pre motor filter and HEPA media post motor filter for dirt accumulation 3 Referto the Cleaning Clogs section on pg 12 4 After the above steps are completed plug vacuum in and continue cleaning If the electronic motor protector continues to activate after following the above steps your cleaner may need servicing Call BISSELL Consumer Services or visit the website Bissell www bissell com AE To reduce the risk of injury from moving parts turn off vacuum cleaner and disconnect power plug from electrical outlet 800 237 7691 N WARNING Troubleshooting To reduce the risk of electric shock turn power OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting Vacuum cleaner won t turn on Possible causes Remedies 1 Power cord not firmly plugged in 1 Check electrical plug 2 Blown fuse tripped breaker 2 Check replace fuse or reset breaker 3 Electronic protector activated 3 Turn vacuum off and unplug see page 12 4 Hose handle not full attached 4 Remove handle and reinstall Brush not rotating fully Possible causes Remedies 1 Brush switch turned
12. into place Cleaning the inner cyclone Unplug the cleaner from electrical outlet 1 www bissell com The inner cyclone can be reached by removing the dirt container releasing the debris door reaching inside the tank and turning the entire assembly to the left to unlock Pull straight down to remove The cyclone and screen may be separated for cleaning Simply twist to unlock amp firmly pull up on the screen to separate Clean the screen with a cloth or soft brush to remove dust and debris The tank may also be wiped clean with a damp cloth Make sure tank is completely dry before reassembling To reassemble hold the carry handle and place the inner cyclone assembly back into tank and turning to lock The section on the screen with no holes should be aligned with cyclone inlet Close the bottom of the door after replacing Bissell az Screen 2 800 237 759 9 Maintenance and care Cleaning the pre motor and HEPA media post motor filter Unplug the vacuum from electrical outlet 1 The pre motor filter protects the motor from dirt particles It is located in the filter compartment underneath the dirt container If the filter becomes dirty lift out the filter and clean This filter may be hand washed in cold water with mild detergent Rinse well and air dry thoroughly before replacing HEPA Media Pre Motor Filter 2 he HEPA media post motor filter assists Post Motor Filter in the fi
13. ltration process to return clean air to the room It is also located in the filter compartment underneath the dirt container If the filter becomes dirty open the filter door remove the filter and replace The HEPA media filter is not washable Rotating brush and drive belt maintenance Do not operate cleaner Check your vacuum cleaner s rotating floor with damp or wet brush and drive belt regularly for debris wear or filters or without all damage Debris can wrap around the brush and filters in place hamper its ability to effectively clean your carpet 1 Unplug cleaner from electrical outlet A Caution 2 Recline handle and turn vacuum cleaner over so the bottom side is up To reduce the risk of injury from moving parts turn 3 Remove the five screws as shown with a Phillips off vacuum cleaner and head screwdriver Lift the brush cover off disconnect Power Plug 4 Lift the rotating floor brush from the from electrical outlet non belt side and pull up and out until tension on belt loosens as shown Slide the belt off the brush and motor pulley to remove brush completely 5 Clean strings hair and other debris from the brush Brush ends caps are removable to allow for additional cleaning 6 Check air passageway for obstructions Remove any debris from this area see instructions on pg 11 7 Clean debris from the motor pulley and drive belt areas 8 Check drive belt carefully for wear cuts or stressed
14. m 800 237 7691 13 Troubleshooting Other maintenance or service not included in the manual should be performed by an authorized service representative Thank you for selecting a BISSELL product If you should happen to need assistance during assembly or operation call 1 800 237 7691 Please do not return this product to the store For any questions or concerns BISSELL is happy to be of service Contact us directly at 1 800 237 7691 BISSELL consumer service For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services Or visit the BISSELL website www bissell com When contacting BISSELL have model number of unit available Please record your Model Number 1 Pleaserecord your Purchase Date NOTE Please keep your original sales receipt It is your proof of warranty 14 www bissell com Sissel 800 237 7691 1 5 Replacement parts BISSELL PROlite Multi Cyclonic series You may purchase replacement parts from your retailer by calling BISSELL Consumer Services or by visiting our website To locate a retailer near you or to place an order using Visa MasterCard Discover or American Express Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m
15. ngs Do not use with any opening blocked keep openings free of dust lint hair and anything that may reduce air flow Bissell Bl Keep hair loose clothing fingers and all parts of body away from openings and moving parts Bl Turn off all controls before plugging or unplugging vacuum cleaner lI Use extra care when cleaning stairs ll Unplug before attaching the TurboBrush WE Do not pick up flammable materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapors BI Do not pick up toxic material chlorine bleach ammonia drain cleaner etc ll Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapors BI Do not pick up hard or sharp objects such as glass nails screws coins etc BI Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes lI Do not use without filters in place BE Use only on dry indoor surfaces lI Keep appliance on a level surface SAVE THESE INSTRUCTIONS FOR FUTURE USE THIS APPLIANCE HAS A POLARIZED PLUG To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualifie
16. ove the bendable wand attachment on the front of the vacuum This switch turns the rotating brush on and off The BRUSH power switch will turn on automatically when the POWER button is turned on and should be used for normal carpet cleaning You may want to turn the brush power switch OFF by pressing the BRUSH switch once for bare floor cleaning or other delicate surfaces or when using the hose Note Your BISSELL PROlite Multi Cyclonic vacuum is equipped with a special internal switch that turns the rotating brush off whenever the unit is in the Upright position Handle position 1 Upright For storage and above floor cleaning with special tools 2 Normal Cleaning Press handle release pedal once Use for most household floor cleaning tasks Automatic height adjustment The powerfoot on your vacuum has an automatic height adjustment and does not need to be manually adjusted when cleaning various floor surfaces The foot design enables the vacuum to move directly from bare floors to low pile and high pile carpets automatically sissell www bissell com N CAUTION Before using your vacuum make sure that both filters Pre Motor and Post Motor are in place Do not operate your vacuum without these filters Tip Your vacuum features a Quick Release Cord Wrap To remove the power cord quickly and easily rotate the upper cord wrap towards floor and slip power cord from upper and lowe
17. r cord wraps Power on off Brush on off AUTO HEIGHT ABIUST Tip Before cleaning under low furniture check area first for objects that might harm the unit or block the Vacuum Hose 800 237 7691 Operation Special tools Your vacuum is not only a powerful floor vacuum A cleaner it s also a versatile above floor vacuum CAUTI 0 N when you select one of the special tools Always place vacuum cleaner on floor in its fully upright position 1 Detach the vacuum hose by grasping the and make sure it is locked into hose handle and lifting to separate from the place when using tools Placing hose grip base the PROlite in its full upright y stop 2 Attach tools by firmly pushing onto vacuum position automatically stops the rotating brush hose or extension wand Bendable wand attachment May be used for cleaning under couches v beds dressers and other hard to reach areas Bend the top portion of the wand to desired angle and attach deluxe floor tool for cleaning Crevice tool Use in tight narrow spaces F NOTE The crevice tool does not store on board TurboBrush Use rotating brush action for small areas such as stairs and upholstery NOTE Press gently when using the TurboBrush to gain maximum cleaning Too much pressure could cause the brush to stop rotating The TurboBrush does not store on board Deluxe floor tool Use with bendable wand attachment to clean under ha
18. rd to reach areas The pivoting lint brush bar collects hair dust and other debris as you pull the attachment back and releases debris into the suction path of the tool as you i push it forward NOTE The deluxe floor tool does not store on board Dusting brush Use brush to dust furniture blinds books lamps shelves baseboards and other delicate surfaces NOTE The dusting brush does not store on board Extension wand Use with desired attachment for a longer reach NOTE The extension wand does not store on board Bissell www bissell com 800 237 7691 1 Operation Power cord storage When you are finished using your vacuum return it to the Upright position and store the power cord 1 Turn vacuum cleaner off by pushing the b power switch 2 Unplug power cord by grasping the polarized plug NOT the cord and disconnect from outlet 3 Loop power cord around cord wraps on back of handle 4 Clip molded plug to power cord to secure Transporting cleaner 1 To move your vacuum cleaner from room to room put the Handle in the Upright Position tilt the cleaner back on its rear wheels and push forward 2 The cleaner can also be moved by using the carrying handle on the dirt container Maintenance and care To maintain maximum cleaning performance the following maintenance steps must be performed 1 Unplug cleaner from electrical outlet 2 Empty the dirt container when the dirt
19. the base of the handle 2 Stand the vacuum upright and slide the base of the handle firmly into the grooves at the top of the vacuum body 3 Checkto be sure the handle is fitted to the vacuum body If there is a gap in front con tinue to push firmly until the handle is flush 4 Insert the two screws from the screw packet into the existing holes Tighten securely with a screwdriver Attach vacuum hose amp on board tools 1 Position the Twist n Snap Hose assembly on the vacuum and line up the tabs on the base of the hose with the corresponding notches Turn the Twist n Snap Hose to the right to lock 1 into place 2 Slide the end of the hose into the hose base Make sure the tab on hose wand inserts into hole on front side of handle Place the hose into the hose clip NOTE The powerfoot will not operate effectively unless the hose is firmly attached to the base 3 Snap the bendable wand attachment into front side of handle 3 4 Place the remaining tools into accessory bag Bissell www bissell com 800 237 7691 5 6 Operation Power switch brush power switch The power switch is located on the handle just above the bendable wand attachment on the front of the vacuum Push the POWER switch once to turn the vacuum on for cleaning and push again to turn the vaccumm off when cleaning is complete The Brush power switch is located just below the power switch on the handle and ab
Download Pdf Manuals
Related Search