quick user manual - Tetra Isı Sistemleri
Contents
1. 2 Parameter Parameter Detail Vale Paramete Parameter Detail Value No Range No Range POO Program Selection 1 2 POO Program Selection 1 2 PO1 Program No Selected PO1 Program No Selected P02 Step No 1 4 P02 Step No 1 4 P03 Cumulative Working Hour 10 P03 Cumulative Working Hour 10 VALUE TEMPERATURE C VALUE TEMPERATURE C P11 1 PROG 1 STEP 50 950 P21 2 PROG 1 STEP 50 950 VALUE WAITING TIME min VALUE WAITING TIME min P12 1 PROG 1 STEP 1 999 P22 2 PROG 1 STEP 1 999 SET VALUE TEMPERATURE C SET VALUE TEMPERATURE C P13 1 PROG 2 STEP 50 950 P23 2 PROG 2 STEP 50 950 VALUE WAITING TIME min VALUE WAITING TIME min P14 1 PROG 2 STEP 1 999 P24 2 PROG 2 STEP 1 999 P15 HEATING RATE C min 3 20 P25 HEATING RATE C min 3 20 Any other parameter set can be made while the selected program is working It does not affect the behaviour of working program 3 4 Buttons Status Mode Heating Mode Parameter Mode Parameter Set Be Short Long Long Short Long Short Long Press Press Press Press Press Press Press Increase Decrease Not Program Parameter Parameter B1 Applicable No Advance Advance he Alle PP Value Value B2 Not Stop Parameter Parameter no igs Applicable Applicable Applicable Back Back Value Value Out B3 Parameter Not Parameter Not Status Parameter Without Savin Mode Applicable Mode Applicable Mode Selecti2. MT9505 P Px MT9503 P Px QUICK USER MANUAL We would like to thank you because you have choosen MT95XX P or MT95XX Px IMPORTANT BEFORE OPERATING THE FURNACE OPERATING MANUAL MUST BE READ CAREFULLY 1 DEFINITION Magmatherm MT95XX P and MT95XXPx are laboratory type heating furnaces Heating is performed up to 9500C This temperature is maximum at the same time continious working temperature of these furnaces 2 SAFETY Magmatherm heating furnace may harm operating people or surrounding any other materials unless this operating manual is applied during operating process Thus Periodical maintenance should be applied Cautions against accidents should be main concern of operators All operating directives warnings and recommendations in this operating manual have to be followed and applied carefully Unless operating directives warnings and recommendations in this operating manual are followed and applied company TETRA ISI S STEMLER LTD STi is not dedicated for the accidents that may occur 2 1 OPERATION IN SAFE CONDITIONS Magmatherm can reach up to 9500C Furnace is not started if there is any living thing in the chamber Any burning flammable exploding poisoning Benzene LPG Acetylene etc material that may harm when it is heated etc is not stored or put inside the chamber These types of materials should be kept away from the furnace Outside case of the furnace may be hot When the furnace
3. is heated you shouldn t touch to outside without gloves Instant high heat should be considered when the front door is open Electronic and or Electrical components may create induction current or magnetic field It may harm any electronic equipment surrounding the furnace Especially cardiac pacemaker users should be away from the furnace It should not be operated in closed environments such as in cupboard etc Furnace should not be operated by multi plug in tools It should be operated by stationary plugs which are mounted on the wall Electricity plug have to be grounded 3 FIRST HEATING Following conditions should be considered directions must be applied step by step and the importance of the first heating process should be kept in mind when Magmatherm Furnace is operated and heated up for the first time 3 1 Enough free field surrounding the furnace should be kept Recommended distance is minimum 30 cm This free space will increase the furnace performance because of air circulation At the same time any fire or explosion danger which may occur due to any material left around the furnace Please don t forget when the furnace reaches to high temperatures the surface of the furnace reaches to high temperatures too Any flammable and explosive material which is close to furnace can be a reason for the fire or explosion danger 3 2 Electricity plug should have proper ground connection and plug should have proper capa
4. city Cable thickness according to maximum amper of the furnace 3 2 Some gas and fumes due to some chemicals which is used on the electronic parts in the isolation materials and due to outer furnace surface paint can be harmful if it is breathed directly during the first heating process Protective glasses and breathing masks should be definitely used during first heating and very good air circulation in the working room should be kept 3 3 During the first heating up process furnace should be heated up according to following temperature time table Heating up to 950 C Waiting for 1 hour This procedure can be completed by Magmatherm Programs easily Please don t touch furnace without gloves especially during first heating process due to hot surfaces 4 KEYPAD amp MENU 3 Haneli Sayisal Nokta Led Led 1 G sterge Ready Heater MAGMA Buton2 Buton 3 B1 B2 B3 Control panel includes 3 buttons B1 B2 B3 green led and red led L1 L2 and 3 digit display If you see green led L1 is on your furnace is ready to start without any problem and the red light L2 starts if you start to heat the furnace When the heating ends the red led also turn off Sound warning is the indication of starting the heating level changes and finishing the heating procedure User interface Key pad has two different mode First one is to understand the status conditions of the furnace Point led is turned off durui
5. e point led is turned on you follow the each parameters of the program Parameter which is wanted to be displayed appears and one second later set value appears at the display B1 and B2 buttons are used to display other parameters Parameter can be changed if B3 button is pressed long and the value starts to blink B1 and B2 are the buttons to decrease or increase the values To save the value B3 is pressed long again while the value is blinking The value is not saved if B3 button pressed short and blinking is stopped 3 3 MENU POO mode activates the program which will be displayed and set Activated menu options depending on the selection of POO are shown here below Parameters of any other program can be changed by changing POO while the selected program is working 3 3 1 MT9505 P amp MT9503 P Menu Parameter Parameter Detail vaie No Range SET VALUE TEMPERATURE C P11 1 PROG 1 STEP 50 950 SET VALUE WAITING TIME Min P12 1 PROG 1 STEP 1 999 P15 HEATING RATE C min 5 25 Parameters above can be set for MT9505 P model Parameter selection mode appears when the B3 button is pressed Point led at the bottom right turnes on and working temperature P11 waiting time P12 and heating rate P15 selection can be implemented MAGMA 3 3 1 MT9505 Px amp MT9503 Px Menu Heat Under Cont MT9505 Px amp MT9503 Px menu is different depending on POO selection as follows IF POO 1 IF POO
6. ng the status mode Unless you press a button inner temperature is indicated on the display If you start to heating and if you press B1 or B2 heating level and heating program can be followed via display 3 1 Start amp Stop for Heating Heating is started if you press 3 4 seconds START B1 button during the Point Led is turned off Firin s tmaya nokta led yanmaz iken Start B1 butonunu uzun basarak ba lat l r Sound warning indicates the initiation of heating and working program number is displayed for 3 seconds and main display is followed That means inner temperature is displayed automatically At the same time red led L2 is turned on If B1 button is pressed short actual level of hetaing procedure is displayed for 2 seconds these are 1 First level heating 2 First level waiting 1 Second level heating 2 Second level waiting It is possible to change the program parameters even the heating continiues But ofcourse this is valid for the coming steps Heating is stopped if you press STOP B2 button long 3 4 seconds Sound warning indicates that you stop the furnace and red led L2 is turned of 3 2 Folowing Entering amp Changing Parameters Second mode is to follow and to change the parameters of the heating procedure Point led at the right bottom of display is turned on This mode is initiated when B3 is pressed short If up or down arrows B1 amp B2 are pressed when th
7. on Saing 8 4 ENERGY CUT OFF amp FURNACE BEHAVIOUR Working program continues to work if the energy cut off occurs and supplied again 5 TECHNICAL INFORMATION Brand Magmatherm Model MT9505 P MT9503 P Software version v12 Maximum Working Temperature 950 C Continious Working Temperature 950 C Power 1 35 kW Voltage 220V Maximum Amperage 7A Frequency 50 Hz Inner Dimensions WxHxD MT9505 P 15 x 15 x 23 cm MT9503 P 11 5x11 5x23 cm Waranty 2 year
Download Pdf Manuals
Related Search