Selador CE Series by ETC - Art Lighting Production, s.r.o.
Contents
1. Rear view to show power data connections and repeating addressing and fan locations Selador Series User Manual Safety Cable The safety cable or other approved safety device should be attached to the fixture housing and wrapped around the hanging structure pipe Appropriate attachment points holes are provided in the protruding tabs on either end of the fixture housing Take care to leave as little slack as possible in the safety cable to avoid the cable catching the yoke of the fixture Safety cable attachment points ju e Fixture Weight Total weight depends on how the individual fixture is configured Weights shown do not include secondary lenses Lustr Vivid R Vivid Fire Vivid Ice and Pearl Mods Shipping weight 42 15 9 19 1 a Does not include mounting hardware Paletta a Does not include mounting hardware Installing Secondary Lenses Up to two secondary lenses can be installed in the slots towards the front of the fixture The stacking order and distance from the LED array are not important to the function of the lenses To avoid lenses being too loose and potentially overlapping each other use the narrower slots for thinner lenses To install secondary lenses Step 1 Loosen the screw on the end of the access panel that has2. Addressing and fans repeat per cell Fuse The quarter turn fuse holder requires a straight blade screwdriver to remove and reinstall a fuse Refer to Fuse Capacities page 17 for information about fuse types Control Use the two push buttons on the bottom of the fixture to set the starting address for the fixture View the LED display with the push buttons on the left The top push button increases the number and the bottom push button decreases the number Pressing and holding the push button increases the rate of change When fixtures are powered up they may temporarily respond to DMX address 001 for the first few seconds of operation New address settings take effect after the LED display turns off CAUTION Do not push the up and down address buttons simultaneously or internal fixture software settings can be inadvertently compromised and performance affected Up and down address buttons are recessed to avoid inadvertent address changes Use a Phillips screwdriver or other blunt device to lightly push the switches To avoid damaging the switches do not use sharp objects or excessive force when changing fixture address Increase LED push button Ss display Decrease push button Addresses must be set between 1 and 505 Selador fixtures are manufactured based 11 LED array or cell Each cell can be addressed individually Eleven inch fixtures
3. 01009 s Fixture address 7 Masterintenstyconro 255 Overalintensty 0 100 Vivid Fire Channo Function Fixture address Red 9255 nensiy 01009 5 Fixture address Fxtueaddress v5 Notus 7s Fixture address 7 Masterintenstyconro 0255 Overalintensty 0 100 Vivid Ice Channo Function C Eure address Red o 9255 S esoo 72 Fixture address 1 Notus o o CS Fxtreaddress 2 O SS Fixture address 5 Bue 9255 tensiy 6 100 s Fixture address 7 Master intensity contol 255 Overall intensity 0 100 Pearl Data Channel Colour Value Function Fixture address Warm white 3200K 0 255 Intensity 0 100 Fixture address 1 Cool white 5700K 0 255 Intensity 0 100 Fixture address 2 Master intensity control 0 255 Intensity 0 100 Note Use individual colour channels to create colour mix Use Master Intensity Control to set fixture intensity Master Intensity Control Channel 8 must be above 0 for the fixture to output Colour Matching This information will be provided in a future release of this manual Selador Series User Manual AN Routine Maintenance General Fixture Cleaning To ensure optimum performance of
4. Electronic Theatre Controls Asia Ltd Technical Services Department Room 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong 852 2799 1220 service etcasia com Electronic Theatre Controls Ltd Technical Services Department 26 28 Victoria Industrial Estate Victoria Road London W3 6UU England 44 0 20 8896 1000 service etceurope com Germany Electronic Theatre Controls GmbH Technical Services Department Ohmstrasse 3 83607 Holzkirchen Germany 49 80 24 47 00 0 techserv hoki etcconnect com Please email comments about this manual to TechComm etcconnect com Selador Series User Manual Document Conventions Throughout this manual the following are used to alert you to notes and safety notices Note Notes are helpful hints and information that is supplemental to the main text gt CAUTION A Caution statement indicates situations where there may be undefined or unwanted consequences of an action potential for data loss or an equipment problem WARNING A Warning statement indicates situations where damage may occur people may be harmed or there are serious or dangerous consequences of an action WARNING RISK OF ELECTRIC SHOCK This warning statement indicates situations where there is a risk of electric shock Safety The Selador series fixtures are intended for professional use only Read entire User Manual before
5. the slot in it Loosen screw Step 2 Raise the panel out of the way but leave it attached to the fixture Step 3 Slide the secondary lenses into the slots above the LEDs Step 4 Lower the panel and tighten the screw Selador Series User Manual Connections and Addressing Connect AC input power and DMX data cables to the appropriate ports as shown below DMX Input DMX Thru e Power Fuse Addressing Connect the incoming DMX data cable to the DMX Input connector If you are daisy chaining the data to other fixtures or DMX controlled devices connect the next DMX cable to the DMX Thru connector The Selador Series fixtures require that the last fixture on a DMX line be terminated with a 1200 resistor between pins 2 and Connect the AC Input cable Align and insert the power connector Twist the connector clockwise until it locks into place Disconnect the AC Input cable Slide back the locking tab twist the connector counterclockwise and pull to unlock and disconnect the power connector Power connection and fuses de Data connections O G9 69000 oooooo e
6. using equipment Please note the following safety notices before use WARNING Note the following safety warnings before use Do not mount the Selador series fixture on or near a flammable surface Use the fixture in dry locations only where humidity does not exceed 90 percent non condensing Fixture is not intended for outdoor use Mount and support the fixture only by the primary suspension holes in the enclosure Suspend the fixture from a suitable structure using only the hardware rated for the weight of the fixture In addition to primary suspension attach a safety cable to the fixture housing Appropriate attachment points holes are provided in the protruding tabs on either end of the fixture housing Disconnect the unit from power and from DMX before all cleaning and maintenance Maximum ambient temperature Ta 40 C Maximum exterior surface temperature Tmax 80 C External Temperature after 5 minutes of full brightness operation and 23 C ambient 38 C External Temperature steady state achieved at 23 C 70 C Installation Power and Data Cabling Requirements Power The Selador series fixture operates on AC power 100 to 240VAC 50 60Hz You may use a circuit powered through an SCR dimmer as long as the dimmer is set to unregulated non dim switched operation Power is supplied through a standard 1 5m power input cable with Neutrik PowerCon locking pigtail with bare ends for attachment of you
7. your Selador series fixture you should perform the following inspections and cleanings at least once a year You may need to inspect or clean the fixture more often depending on the type and amount of use your fixture experiences during the year CAUTION Allow fixture to cool down completely prior to cleaning Disconnect all power and DMX cables prior to cleaning Check for excessive dust or debris in the heat dissipating fins around the entire fixture enclosure Clean using compressed air or a soft cloth Keeping the heat sink components of the enclosure clean facilitates efficient cooling and extends LED longevity NEVER spray liquids into the fixture NEVER spray compressed air into a fixture that is powered up A can of compressed air or oil free air from an air compressor set at a low setting can be used to blow through the vent holes and remove dust or other debris from the interior of the fixture Dust build up can cause overheating and premature shutdown Remove the secondary lenses if used and clean out any dust and debris All components including the secondary lenses can be cleaned using compressed oil free air as described above or a clean micro fiber cloth The use of any liquid cleaning solution is not recommended for Selador fixtures Inspect all mounting hardware for wear and if necessary clean using compressed oil free air or a soft lint free cloth Cooling Fan Filter Cleaning Cooling fan f
8. 7 1989 Luminaires Particular requirements Specification for luminaires for stage lighting television film and photographic studios outside and indoor following the provisions of EU LV Directive s 2006 95 EC EN 55015 2006 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EN61000 6 2 2005 Electromagnetic compatibility EMC Generic standards Immunity for industrial environments Including EN61000 4 2 1995 ESD requirements EN61000 4 3 2006 A1 2008 Radiated susceptibility EN61000 4 4 2004 Electrical fast transients EN61000 4 5 2006 Surges EN61000 4 6 2007 Conducted susceptibility EN61000 4 11 2004 Voltage dips and interruptions EN61000 3 2 2006 Electromagnetic compatibility EMC Limits Limits for harmonic current emissions equipment input current up to and including 16 A per phase Class A EN61000 3 3 1995 Electromagnetic compatibility EMC Limits Limitation of voltage fluctuations and flicker in low voltage supply systems for equipment with rated current lt 16 A following the provisions of EU EMC Directive s 2004 108 EC London United Kingdom Mr Adam Bennette Place of issue Name of authorised person n 7 I j D tann 18th August 2010 Date of Issue signature of authorised person Printed 18 Aug 10 Page 1 Decl 93 Version C lon file2 Shares RND DofC Master declaration doc Electronic Theatre Contr
9. Germany Tel 49 80 24 47 00 0 Fax 49 80 24 47 00 3 00 Hong Kong Rm 1801 18 F Tower 1 Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong Tel 852 2799 1220 Fax 852 2799 9325 Service Americas service etcconnect com UK service etceurope com DE techserv hoki etcconnect com Asia service etcasia com Web www etcconnect com Copyright 2010 ETC All Rights Reserved Product information and specifications subject to change 7401M1210 m Rev C m Released 2010 09
10. aces the original Vivid fixture as of February 2010 The manufacturer of the K2 LED emitter is phasing out these emitters over the next year Vivid R maintains photometrics equivalent to the original Vivid with higher intensity and uses less power Physical Rugged extruded anodised aluminum construction Advanced thermal management systems for long LED life 0 to 40 C ambient operating temperature Available in 279 546 1080 and 1613mm lengths On board fan speed control for no noise operation unless in high ambient temperature situations Fixtures built January 2010 and after Electrical Yoke trunnion floor stand or pipe hanger mounting options Available in black See Dimensions and LEDs page 3 See Fixture Weight page 10 100V to 240V 50 60 Hz internal power supply Neutrik PowerCon input connector LEDs 1 5m power lead supplied Requires power from non dim source Luxeon Rebel 2 5W LED emitters Lustr Paletta Vivid R Vivid Fire Vivid Ice and Pearl Luxeon K2 3 5W LED emitters original Vivid fixtures manufactured before February 2010 Optical 50 000 hr LED life See Note About LED Fixtures page 3 Integral 16 field angle optic Pearl Integral 18 field angle optic original Vivid Integral 19 field angle optic Vivid R Integral 26 field angle optic Lustr Paletta Vivid Fire and Vivid Ice Slots for secondary lenses Colour Combine sec
11. edictable service for extended periods of time in ambient temperatures up to 40 When the fan turns on its speed ramps up slowly in order to minimise the noise differential CAUTION Duty Cycle Operating the fixtures in higher ambient temperatures or low airflow situations may cause the power supply to shut down Following a cool down period the power supply will automatically reset and the fixture will return to operation It is good practise to power down any device with on board electronics to limit unnecessary wear on the devices and eliminate residual use of electricity When not in use Selador fixtures should be powered down by disconnecting from power either at the breaker or by unplugging LED life is adversely affected by high temperature operation Whenever possible avoid turning all channels to 10096 for extended periods such as channel checks or focusing 180 265mm 290mm 180mm 255mm i Floor trunnion dimensions 345mm 235mm 2 180mm 160mm Paletta mm 180mm 315mm 290 235 225mm Paletta Hanging dimensions 225mm Paletta Hanging bracket Front view dimensions 54 6cm 1 27 9cm _ p 108cm 161 3cm
12. ft during 63 fixture provides 6 independently controllable cells dimming Digital LED display for address assignment Optional Secondary Lenses Beam spreading lenses available from 20 to 80 in Easily interchangeable horizontal and vertical axis Combine up to 2 secondary lenses at a time Maximum Power Consumption at Full Intensity Lustr Vivid R Vivid Fire Vivid Ice and Pearl eee a E Paletta a Vivid Fire and Vivid Ice are available in 11 and 21 versions only Wedel Current a Watts Vivid Manufactured January 2010 or before 1068 Dimensions and LEDs Lustr Vivid Vivid R Vivid Fire Vivid Ice and Pearl Paletta Size in millimeters Number of LEDs 279x180x180 346x180x180 w 1080 x 180 x 180 1613 x 180x 180 a Vivid Fire and Vivid Ice are available in 11 and 21 versions only Models Size in millimeters Number of LEDs 279 x 160 x 160 Bux 180x160 19 1080 x 180 x 160 1613 x 180 x 160 Note About LED Fixtures All LED sources experience some lessening of light output and some colour shift over time Selador Series fixtures have complex thermal management systems to minimise these changes With typical usage a Selador fixture will still achieve 70 of its initial output after 50 000 hours of use In individual situations LEDs will be used for different durations and differe
13. have one cell 21 fixtures have two cells 42 fixtures have four cells and 63 fixtures have six cells A 42 fixture can be addressed as four individual cells one cell or any combination Each Selador fixture must be considered a separate DMX device for the purpose of DMX line loading calculations with the exception of 63 fixtures These 63 fixtures must each be considered 1 5 DMX devices for line loading number of Cells Number of Devices DMX line loading practice dictates that no more than 31 devices can be daisy chained together Consequently no combination of Selador fixtures totaling more than 31 DMX devices should be configured in one DMX line For example twenty 6 cell units 30 DMX devices are okay Twenty one 6 cell units 31 5 DMX devices are not acceptable For runs of fixtures totaling more than 31 DMX devices split the DMX runs by using a DMX splitter Note A fixture with a starting address higher than 505 will not have control of all parameters Therefore 505 is the highest address shown on the address display Selador Series User Manual Each cell of Selador Series fixture occupies eight DMX channels Seven are individual colours and the eighth is the master intensity The table below describes the order and function of each address Lustr Paletta and Vivid R Channel vawe Function E Red __ ensiy 0 100 6 Fintureaddress 5 Bue oas
14. ilters should be inspected at a minimum every six months more frequently if fixtures are powered on for more than four hours per day Use a vacuum cleaner to remove dust from each fan filter In dusty environments or conditions involving the use of smoke machines clean the filters as follows Using fingernail or small flat blade screwdriver remove fan filter cover by prying under one of the two locking tabs Carefully remove foam fan filter from fan assembly Gently wash foam fan filter in a solution of mild dishwashing solution and water e Thoroughly rinse each foam fan filter in clear water e Pat dry or air dry filters After filters are completely dry reinstall by inserting them into fan assembly e Reattach the filters to the fixture Note Nouser serviceable parts are inside Fuse Capacities All Selador Fixtures use 3AG 250V 32mm x 6mm fuses Use the following capacity fuses for all Selador fixtures Fuse value 17 Selador Series User Manual Corporate Headquarters 3031 Pleasant View Road Box 620979 Middleton Wisconsin 53562 0979 USA Tel 608 831 4116 Fax 608 836 1736 London UK Unit 26 28 Victoria Industrial Estate Victoria Road London W3 600 UK Tel 44 0 20 8896 1000 Fax 44 0 20 8896 2000 Rome IT a Via Pieve Torina 48 00156 Rome Italy Tel 39 06 32 111 683 Fax 44 0 20 8752 8486 Holzkirchen DE Ohmstrasse 3 83607 Holzkirchen
15. nt levels This can eventually lead to minor alterations in colour performance necessitating slight adjustment to presets cues or programs All LEDs exhibit a slight colour shift as their temperature rises from ambient to operating temperature This may or may not be visible to the eye If this is a concern a five to ten minute warm up cue all colour channels at 10096 intensity channels at 5096 prior to production can minimise this effect Selador Series User Manual Overview Congratulations on your purchase of a Selador Series by ETC product Selador s x7 Color System seven hue technology produces a light and colour quality that conventional LED systems cannot duplicate This unique colour system produces bright broad spectrum whites and intense colours equally well rendering pigments objects and skin tones in a natural way Vivid Fire and Vivid Ice fixtures use elements of the x7 Color System for superior performance in deep saturated colours Each member of the Selador Series product line is unique and optimized for a specific lighting task Lustr e Luxeon Rebel 2 5W LED emitters e Optimized for the best white light across the entire CCT range Beautifully illuminates skin tones and other objects Paletta e Luxeon Rebel 2 5W LED emitters Optimized for deep pure pastels and saturated colours e Interacts seamlessly with conventional sources Vivid R e Luxeon Rebel 2 5W LED emitters e Optimized for high outpu
16. oelador CE Series by ETC Lustr Paletta Vivid Vivid R Vivid Fire Vivid Ice Pearl User Manual 2010 09 The Selador series of fixtures are intended for professional use only Read entire User Manual before using equipment Copyright 2010 Electronic Theatre Controls Inc All rights reserved Product information and specifications subject to change Part Number 7401M1210 Rev C Released 2010 09 ETC and Selador are registered trademarks of Electronic Theatre Controls Inc in the United States and other countries Other product and company names mentioned herein may be trademarks and or service marks of their respective owners ETC permits the reproduction of materials in this manual only for non commercial purposes other rights are reserved by ETC This product is protected by one or more of the following U S Patents 6 016 038 6 150 774 6 788 011 6 806 659 6 683 423 and 7 023 543 ANES transtechnik avab C DECLARATION OF CONFORMITY Tel 44 0 20 8896 1 00 Fax 44 0 20 8896 2000 We Electronic Theatre Controls Limited declare under sole responsibility that the product Product name Selador LED luminaire Product type model Vivid Vivid R Lustr Pearl Paletta Vivid Fire amp Vivid Ice Item numbers All sizes to which this declaration relates is in conformity with the following Standards EN 60598 1 2004 Luminaires General requirements and tests EN 60598 2 1
17. ols Ltd Registered Office Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU Registered in England No 3057796 VAT No GB 662 9487 90 Table of Contents Specifications 1 Maximum Power Consumption at Full Intensity 2 Dimensions and LEDs 3 Note About LED 3 4 Applications e tope ess e e gan 5 Document 6 Safety ox ert 6 Installation 7 Power and Data Cabling Requirements 7 nd ecard Nee RE dix pepe d m 7 Data udi mre este oo toot Pa 7 Installation Procedures 8 Installing Mounting 8 Installation Notes 8 Safety 10 Fixture Weight 10 Installing Secondary 11 Connections and 5 12 Control adios scent p d 13 Routine Maintenance 16 General Fixture Cleaning 16 Cooling Fan Filter Cleaning 17 17 Specifications Note Vivid R repl
18. ondary lenses for desired beam spread Selador Seven color x7 LED products for superior broad spectrum colour mixing Lustr Optimized for highest output in white and light tints in a 7 color fixture Paletta Optimized for strong saturated colours Vivid Vivid R Optimized for strong saturated colours at maximum brightness Selador special purpose LED fixtures Vivid Fire Optimized for high intensity saturated colours on the red end of the spectrum Vivid Ice Optimized for high intensity saturated colours on the blue end of the spectrum Pearl High output warm and cool white LEDs for variable colour temperature white only light output Interacts seamlessly with conventional sources Achieves excellent 3200 or any other Correlated Colour Temperature white light from 800 to 20 000 K except Vivid Fire Vivid Ice and Pearl Beautifully illuminates skin tones and other objects Deeply saturated colours across an exceptionally wide gamut Colour rendering as high as 90 CRI except Vivid Fire Vivid Ice and Pearl Selador Series User Manual DMX512 A compliant Internal control electronics for smooth low end dimming at 15 bit resolution DMX in and thru via 5 pin XLR connectors 21 fixture provides 2 independently controllable cells 8 channel 7 colour plus intensity 42 fixture provides 4 independently controllable cells ntensity channel minimises colour shi
19. r desired connector Data The Selador series fixtures operate on a DMX control signal The unit is supplied with a 5 pin XLR DMX input connector and a 5 pin DMX Thru connector DMX cables should be acceptable for DMX data transmission not microphone cable and should follow the standard pinout The optional secondary data pair is not used by the Selador series fixtures The maximum DMX data run from any DMX source to the last fixture in a chain is 300m Termination is required in the data thru port of the last fixture in each data chain DMX512 pinout for five pin XLR female Common Shield Data Data not connected not connected See Control page 13 for additional information on DMX addressing of Selador Series fixtures 7 Selador Series User Manual Installation Procedures Installing Mounting Hardware Four different options are provided for mounting Selador fixtures Yoke for 11 and 21 fixtures Double yoke for two 11 or two 21 fixtures over under configuration Floor trunnions for all fixtures Pipe hanging brackets for all fixtures Note Trunnions should be installed with the feet inward so that fixtures can be lined up end to end if needed Installation Notes Cooling and Duty Cycle Selador Series fixtures are equipped with ultra quiet cooling fans These fans are automatically controlled They permit fan free operation when possible and turn on only when needed to provide low noise pr
20. t deep pastels and strong saturated colours Narrow optics for the longest throws Vivid Fire e Luxeon Rebel 2 5W LED emitters e Optimized for saturated colours at the red end of the spectrum Strong output for high intensity theatrical environments Vivid Ice e Luxeon Rebel 2 5W LED emitters e Specialized LED array e Optimized for saturated colours at the blue end of the spectrum Strong output for high intensity theatrical environments Pearl e Luxeon Rebel 2 5W LED emitters Specialized LED array High output warm and cool white LEDs for variable colour temperature white only light output from 3200 to 5700K Information in this manual is applicable to all Selador Series by ETC products unless stated otherwise Applications Theatres e Studios e Churches Hotels e Convention Centers Schools Application 53 Frusswarmer i Fe J e seim Ke LL Fig _ Specs I EE pom Backight Sagewash em _ If you have questions about your Selador series fixture that are not answered in this manual please contact the supplier of your ETC equipment or ETC Technical Services Americas United Kingdom Electronic Theatre Controls Inc Technical Services Department 3031 Pleasant View Road Middleton WI 53562 800 775 4382 USA toll free 1 608 831 4116 service etcconnect com Asia
Download Pdf Manuals
Related Search