Bains Marie Instruction manual
Contents
1. Bains Marie Instruction manual Model L371 A S007 A S047 A Safety Tips Position on a flat stable surface A service agent qualified technician should carry out installation and any repairs if required Do not remove any components on this product Consult Local and National Standards to comply with the following e Health and Safety at Work Legislation e BS EN Codes of Practice e Fire Precautions e IEE Wiring Regulations e Building Regulations DO NOT immerse the appliance in water or use jet pressure washers to clean it DO NOT touch hot surfaces with bare hands Always use the handles protective gloves DO NOT overfill the appliance Keep the water level below the MAX level DO NOT allow the water level to drop below the MIN level during operation DO NOT move the appliance when it contains hot liquid DO NOT use the appliance for anything other than its intended use Always switch off and disconnect the power supply to the appliance when not in use Not suitable for outdoor use Keep all packaging away from children Dispose of the packaging in accordance to the regulations of local authorities If the power cord is damaged it must be replaced by an Apuro agent or a recommended qualified technician in order to avoid a hazard Product Description L371 A Apuro Bains Marie S007 A Apuro Bains Marie with Pans S047 A Apuro Bains Marie with tap Introduction Please take a few moments to carefully read throug2. d period on stainless steel Use a suitable stainless steel cleaner e Dry the exterior thoroughly e Wash all removable parts in warm soapy water Troubleshooting If your Apuro appliance develops a fault please check the following table before making a call to the Helpline Fault Probable Cause Action The unit is not working The unit is not switched on Check the unit is plugged in correctly and switched on Plug and lead are damaged Call Apuro agent or qualified technician Fuse in the plug has blown Replace the plug fuse Power supply Check power supply Internal wiring fault Call Apuro agent or qualified technician The Thermal Cut Out switch has activated Reset Thermal Cut Out switch The thermostat has not been set correctly Set the thermostat to a higher temperature The heating element has failed Call Apuro agent or qualified technician Telephone Helpline 1300225960 United Kingdom Technical Specifications Model Voltage Power Current Ben Weight L371 A 220 240V 50Hz 1300W 5 5A 245 x 340 x 580 8kg S047 A 220 240V 50Hz 1300W 5 5A 245 x 340 x 605 11kg so77 A 220 240V 50Hz 1300W 5 5A 355 x 340 x 580 10 7kg Electrical Wiring The plug is to be connected to a suitable mains socket This appliance is wired as follows e Live wire coloured brown to terminal marked L e Neutral wire colo
3. h this manual Correct maintenance and operation of this appliance will provide the best possible performance from your Apuro product Telephone Helpline 1300225960 United Kingdom Pack Contents The following is included e Apuro Bains Marie e Instruction manual e Pans2x1 3 and 2 x 1 6 S007 only e Support bars S007only Apuro prides itself on guality and service ensuring that at the time of packaging the contents are supplied fully functional and free of damage Should you find any damage as a result of transit please contact your Apuro dealer immediately Operation Power Switch Thermostat Dial Power Indicator Light 1 Connect the appliance to the power supply 2 Fill the tank with water to a level between the MIN and MAX marks on the inside of the tank N Note Apuro recommend that fresh water be used each time the appliance is used 3 Switch the power switch to the On position 1 The red power indicator light will turn on 4 Turn the thermostat to the desired temperature to heat up the appliance 5 Once the appliance has heated the water the power indicator light turns Off 6 Reduce the heat setting on the Thermostat to maintain temperature WARNING Do not allow the water to drop below the MIN level during operation Severe damage to the heating element could result Maintaining Water Levels It is important to regularly check the water level in the Bains Marie tank e Always keep the water leve
4. l above the MIN mark on the inside of the tank during operation e Damage to the heating element can occur if the tank boils dry and the element may have to be replaced e This is not covered by the Apuro warranty Emptying the Appliance N Note Always switch the appliance off allow the water to cool before emptying Use a suitable container to remove the water from the appliance S047 A turn on the tap to drain the water Ensure a suitable a suitable container is used to remove the water from the appliance Thermal Cut Out Reset This appliance is fitted with a Thermal Cut Out safety feature Should the temperature exceed safe levels the appliance will automatically cut power The Safety Cut out switch is located on the underside of the appliance To reset the appliance after a sufficient cool down period 1 Press the small reset switch down until it clicks using a blunt pointed instrument 2 The appliance is now reset and can be used as normal N WARNING Ensure the appliance has cooled down and is empty before resetting the switch as it may need to be tipped slightly to gain access to the switch Cleaning Care amp Maintenance Note Always switch off and disconnect the appliance from the power supply before cleaning Always allow the appliance to cool before emptying or cleaning e Wipe down the exterior of the appliance with a damp cloth e Some cleaning agents may cause damage when used for a prolonge
5. ured blue to terminal marked N e Earth wire coloured green yellow to terminal marked E This appliance must be earthed using a dedicated earthing circuit If in doubt consult a gualified electrician Electrical isolation points must be kept clear of any obstructions In the event of any emergency disconnection being reguired they must be readily accessible Compliance The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste To help prevent possible harm to human health and or the environment the product must be disposed of in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the product supplier or the local authority responsible for waste disposal in your area Apuro parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international independent and federal authorities Apuro products have been approved to carry the following symbol All rights reserved No part of these instructions may be produced or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Apuro Every effort is made to ensure all details are correct at the time of going to press however Apuro reserve the right to change specifications without notice Equipment T
6. ype Model Legislation Standards Producer Name Producer Address DECLARATION OF Bains Marie S007 A L371 A S047 A C Tick AS NZ 3820 Essential Safety Requirements for Low Voltage Electrical Equipment EN 55014 1 2000 A1 EN 55014 2 1997 A1 EN 61000 3 2 2000 EN 61000 3 3 1995 A1 IEC 60335 2 30 2003 Annex ZZ of AS NZS60335 1 2002 A3 Apuro Unit 2 34 38 Anzac Ave Smeaton Grange NSW 2567 I the undersigned hereby declare that the eguipment specified above conforms to the above Legislation and Standard s Date Signature Full Name Position 18 03 11 Richard Cromwell Marketing Director e Notes L371 A_S007 A_A5_v3
Download Pdf Manuals
Related Search