User manual
Contents
1. 26 Installation of safety loop ees 26 Using the transportation kit 26 Direction lock 28 Install the direction loche e 28 Activate direction lock sseeeeesee 28 Releasing the direction locle 28 User manual Zitzi Guppy 4 Mudguards 2 een 29 PALM rain Tasta tes 34 Installation of mudguards 29 Stability meer 35 Adjusting the mudguard 29 Tubular frame and details 35 F rks unse 35 Transportation in a vehicle 31 Driving bow and push handle 35 Guidelines for transportation in a car 31 Brakes an ee E TE 35 Crash tested and approved 31 Folding mechanism and tilt 35 F riction Control usa treten nen 35 Maintenance instructions 32 Service intervals setis dere 32 Adaptation and customization 36 Cleaning and washing instructions 32 Recommendations sse 36 GaS pISUOEL ui 32 Risk assessment 36 Warrant Ycee e e pEpeti bu seitens 33 Coibiatiofigus sie 33 Terms of sale mm eto Gs 37 Spare Dal tS 33 Waranty Merc maionesa cata mari guies 37 Marking usa nein 33 Warranty claims seen 37 Recyclin2. C Loosen the vvheel vvith the quicle release function see page 12 Loosen the screw that holds the rotationlocker on the brake see page 20 and then remove the spacer Mount the mudguards and replace the removed spacer with the supplied shorter spacer B Adjusting the mudguard You can adjust the mudguars in height by loosen the screws D Adjust to re quired heigt and then tighten the screws D Tips You just need to loosen the screws D slightly Anatomic SITT AB User manual Zitzi Guppy 29 Indication for transportation brackets Guppy from above with the drive wheels closest to the footer Anatomic SITT AB User manual Zitzi Guppy 30 Transportation in a vehicle Guidelines for transportation in a car Fixing shall be done vvith straps approved to ISO 10542 the intended transport brackets as marked on the image description N Note It is important that you only stretch the strap to low tension Over tensing of the straps can cause the frame to become warped Crash tested and approved is crash tested and approved according to ISO 7176 19 up to 7O kg Note Crash test is approval valid for weights up to 70 kg Anatomic SITT AB User manual Zitzi Guppy 31 Maintenance instructions Service intervals In order for the device to work properly regular service and inspection must be performed The need for service depends on frequency of use and wear Check all moving par
3. eg at pa vements Push the step bar with your foot while holding the driving handle and gently pull the chassis backwards to free up some space under the castors Obs A It is important to hold the driving handle firlmy while using the step bar Anatomic SITT AB User manual Zitzi Guppy 24 Transportation kit Installation of front bracket Mount the bracket with screw A and washer B to the chassis as illustrated Do not forget to mount the distance C as well Installation of rear bracket The rear bracket shall be munted on the outside of the profile at the rear of the chassis using the supplied screws D washers E and nuts F as illustrated Installation of safety loop Install the safety loop on the inside of the profile with screws G washer H and tube I The upper bracket is mounted at the rear of the seatplate with screws J and nut K Using the transportation kit See Transport in vehicle for more information and recommendations on how to use the transportation kit safetly Check up The lock on the safety loop should automatically lock when you fold the loop towards the upper bracket Obs The push frame shall always be in contact with the seating systems back during transportation in a vehicle Craschtested and approved Craschtested and approved according to 7176 19 for 70 kg Note When using the transportation kit the angle of the chassis has to be 0 gt P gt gt
4. is valid for one 1 year from delivery date Warranty is void ifthe product has been subjected to external factors or rough handling It s required that the faulty product is returned for us to process a warranty claim Always attach the packing slip of the original delivery Warranty claims Describe the error and the possible cause for this as thoroughly as possible Claim repairs or possible replacement under warranty Always attach a copy of the invoice and state that the product should be returned to you after repairs Provide a shipping address a contact person and a phone number Make sure that you pack the product well to protect it from shocks during the transportion Note the shipping number in your documentation This is so that you can track the shipment should anything occur during transport Returning products In the event of faulty orders or deliveries the products should be returned within 20 days from delivery Always attach a copy of both the packing slip and the invoice Provide your reason for returning the products Make sure that you pack the product well to protect it from shocks during the transportion Note the shipping number in your documentation This is so that you can track the shipment should anything occur during transport For products returned more than 20 days from delivery a refund is made of 80 of the invoice value For products returned more than 60 days from delivery a refund is made of 60 of th
5. 2014 09 02 BR201209 01 UT 02 NL User manual ZITZI GUPPY Check the checkbox if the product is CUSTOMIZED The CE Mark is no longer valid and should be removed Da Gnatomic E SITT The product is only intended for use as an under frame together with seating systems produced by Anatomic SITT AB If other uses are desired please contact Anatomic SITT AB Safety precautions Introduction For you to use all advandtages of the Zitzi Guppy it is important that you read through this manual thoroughly This applies to all persons vvho are in the vicinity of the user Adjustment of the Zitzi Guppy should alvvays be performed by medically qualified person If you need additional information please contact Anatomic SITT AB Correspondence Zitzi Guppy and its accessories are CE marked products A unique serial number is located on a label placed on the lower part of the frame This serial number should be quoted in any correspondence regarding the product Craschtested and approved Zitzi Guppy is craschtested and approved according to 7176 19 for 70 kg in vehicle Obs A The prescriber or person with equivalent qualifications and knowledge of the user and the tool will always carry out a risk assessment before use If this analysis shows that there may be a risk of serious injury the user must never be left unattended when using the Guppy This product is manufactured by Anatomic SITT AB Pos
6. Anatomic SITT AB User manual Zitzi Guppy 25 Direction lock Install the direction lock Mount the direction lock to the castors using the supplied details Start by removing the castor attachment A from the chassis attachment B by removing the screws C Then lift the end seal D from caster attachment A top and remoe the center bolt E Then mount the directional lock details F between the caster attachment A and chassis attackhment B and between the caster attachment A and the caster fork G with the supplied details as illustrated When the direction lock is installed mount the caster on the chassis again You can adjust the direction lock by slightly adjusting screw J Tips For more information about installing the castors see page 18 21 Activate direction lock Pull the locking pin H straight up and then rotate 90 and release the pin I into the hole in the movining part Ensure that the direction is locked Releasing the direction lock Pull the locking pin H straight up and then rotate 90 and release the pin into the hole in the movining part Ensure that the direction is locked T Note Direction lock fits only by choosing the 7 castors Anatomic SITT AB User manual Zitzi Guppy 27 Direction lock Anatomic SITT AB User manual Zitzi Guppy 28 Mudguards Installation of mudguards Mount the mudguards vvith the supplied screvvs A the spacer B and nuts
7. aru Ltd Peterburi tee 14A EST 114 11 Tallin Tel 372 621 25 82 Fax 372 638 08 78 MMS Medical Ltd 51 Eastgate Drive Little Island Cork Tel 353 021 461 8000 Fax 353 021 461 8099 Mobilitec Rua dos Verdes 123 PRT 4470 658 Pedras Tel 351 229 436 130 Fax 351 229 436 139 e 8 9060069 8 amp amp OX Orthop dix 27 rue Francois Gillet FR 42400 St Chamond Tel 33 477 195 994 Fax 33 426 303 789 Ortopedia Castagna Centro Tecnico Via Ghislanzoni 18 B IT 23900 Lecco Tel 39 341 362 671 Fax 39 341 360 931 Rehatec AG Ringstrasse 15 CH 4123 Allschwill Tel 41 614 879 911 Fax 41 614 879 910 Stod Hf Stoaekjadmidin Tronuhraun 8 IS 220 Hafnarfjordur Tel 354 565 2885 Fax 354 565 1423 Scan Ideal 28 Tzavela Str GR 542 49 Thessaloniki Tel 302 310 320 150 Fax 302 310 350 151 Team Nova Reha Gerecja vas 33 SVN 2288 Hajdina Tel 386 278 201 06 Fax 386 278 201 06 Via Libre Fundosa Accesibilidad Don Ramon de la Cruz 38 ES 28001 MADRID Tel 34 911 213 031 Fax 34 911 213 025 Asia Pacific and Middle East Al Safwa Mobility LLC ASM Al Falah Street Harley Davidson 2001 Abu Dhabi Tel 971 264 242 62 Fax 971 264 242 63 Email info alsafwamobility ae Paediatric Mobility Equipment Po Box 1118 Young AUS NSW259 Tel 61 1300 131 884 Fax 61 1300 884 010 Email sales paedmobility com au Cubro Rehab PO Box NZL 9144 Tauranga Tel 64 757 78 816 Fax 64 757 78 827 Special nee
8. aster Mount a washer H lock nut I on the other side and tighten Finish by placing a nut cover J over the lock nut See the picture below Caster positioning You kan adjust the castors in five different height positions This allows you to adjust the castor height after positioning the driving wheels Obs A OBS Secure that the screws is properly tighten after the adjustment Anatomic SITT AB User manual Zitzi Guppy 14 Caster Caster fork position You may need to adjust the caster fork A if the wheelchair doesn t roll properly This can occur when adjusting the caster position without adjusting the caster fork A Make sure that the position of the caster attachment B is 90 in proposition to the ground as illustrated Angle adjustment of caster fork Loosen and rotate the eccentric nuts C on the caster attachment B until the correct angle is obtained Tighten the screws properly after adjusting the caster fork Obs A Make sure the screws are properly tightened after the adjustment Anatomic SITT AB User manual Zitzi Guppy 15 B Detailed drum brake User manual Zitzi Guppy 16 Brake Drum brake The wheels are equipped with drum brakes that can be activated by the caretaker Always check that the brakes are working properly before use Press the right brakehandle A while pusching the wheelchair forward The brakehandle A should not be possible t
9. avoid risk of pinching while tilting the seat A Obs Be aware of the possible increased risk of overturn during tilt Anatomic SITT AB User manual Zitzi Guppy 7 al Zitzi Guppy 8 manu Anatomic SITT AB Armrest Mounting on the frame Loosen the screws A completely on each side Mount the mounting bracket around the driving bow Put back the screws A and tighten Height adjustment Loosen the screws A and adjust to required height Tighten the screws Width adjustment Loosen the screws B and adjust to required width Tighten the screws Angle adjustment upwards and downwards To adjust the angle of the armrest loosen the adjuster C and adjust it to the required angle To compensate you can also adjust the angle in the armrests attachment Loosen the screws A and adjust the angle using the three holes E in the attachment Depth adjustment Loosen the screws D underneath the armrest plate and adjust to required position using holes underneath Anatomic SITT AB User manual Zitzi Guppy 9 Anatomic SITT AB User manual Zitzi Guppy 10 Driving handle Installation of the driving handle Insert the attachment of the pusch frame A in the provided holes under neath the seatplate on the rear ofthe chassis and then tighten the screws B Choose between the four fixed positions Depth adjustment of the driving handle To adjust the push frame extend the depht of
10. d back tube and push bar and that it s easily to tilt the unit See page 8 9 for more informtion about the tilt Function control Function control means that you go through wheels stability brakes push handle and push bar A Noticel Always check that the device is not customized when reconditioning before it is sent to new users Anatomic SITT AB User manual Zitzi Guppy 35 Adaptation and customization Guidelines and recommendations Every time the Zitzi Guppy is altered in some vvay an assessment has to be made to determine if it is an adaptation or a customization An adaptation is any change made in comprehension of the CE mark All other changes are customizations Adaptations must only be made by a person deemed to be qualified for the task and should always be made in a professional manner The CE mark means that the product fulfils all of the essential European safety requirements Risk assessment Note that a risk assessment always should be done for an adaptation as well as for a customization of a medical aid The product must never become dangerous to use after adaptation The product should be fitted with a note that it is adapted to a specific user so that it cannot be mistaken for a standard model product Note A The CE mark is no longer valid if the product is customized Anatomic SITT AB User manual Zitzi Guppy 36 Terms of sale Warranty Warranty against manufacturing errors
11. ds for Special children 48 Mordey Hagetaot St Beer Sheva ISR 84840 Tel 972 8 62 875 85 Fax 972 862 819 61 The Gym amp Care 1F 23 amp 24 IOI Business Park MYS 47100 Puchong Tel 603 8070 9166 Fax 603 8073 9166 Email info gymncare com User manual Zitzi Guppy 38 Technical data with 16 wheels 6 casters Seat height Weight Size 1 0 32 46 cm 14 kg 5lcm 67 73 cm 41cm 57 cm 41cm Size 2 0 32 46 cm 14 kg 56 cm 67 73 cm 41 cm 57 cm 46 cm with 20 22 24 wheels 6 casters Seat E height Weight wiht mud flaps Size 1 0 32 46 cm 20 15 kg 57cm 71 82 cm 41cm 57cm 43 5 cm 39 5 cm Size 2 0 32 46 cm 20 15 kg 62 cm 71 82 cm 41 cm 57 cm 48 5cm 44 5 cm The total lenght of the chassi change depending on location and wheels C measurement is taken at the height of castor house Anatomic SITT AB User manual Zitzi Guppy 39 Anatomic SITT A SE DK NL Anfall soot C C Da Anatomic Anatomic SITT AB manufacturer Box 6137 SE 600 06 Norrk ping Tel 46 11 16 18 00 Fax 46 11 16 20 05 Support 46 11 16 18 05 Visiting adress Terminalgatan 1 SE 603 61 Norrk ping Anatomic SITT A S Viengevej 4 8240 Risskov Denmark Tel 45 86 17 01 74 Fax 45 86 17 01 75 Anatomic SITT Nederland B V Postbus 6027 4000 HA Tiel The Netherlands Tel 31 344 63 45 40 Fax 31 344 62 33 61 anatomicsitt c
12. e invoice value For products returned more than 150 days from delivery a refund is made of 40 of the invoice value For products returned more than 360 days from delivery no refund is made for the products A Customized products cannot be returned Anatomic SITT AB User manual Zitzi Guppy 37 000600 008 388 8 Anatomic SITT AB Customer service Scandinavia Anatomic SITT AB Box 6137 SE 600 06 Norrk ping Stohagsgatan 26 SE 602 29 Norrk ping Tel 46 11 161800 Fax 46 11 162005 Email info anatomicsitt com Anatomic SITT A S Viengevej 4 DK 8240 Risskov Tel 45 861 701 74 Fax 45 861 701 75 Email a sitt anatomic sitt dk Bardum A S H ndverksvein 8 N 1405 Langus Tel 47 64 91 80 60 Fax 47 64 91 80 66 Handico Finland OY Asemanaukio 7 FIN 04200 Kerava Tel 358 331 222 700 Fax 358 331 222 710 Email handico handico fi Europe Anatomic SITT Nederland BV Sir Rowland Hillstraat 1C NL 4004 JT Tiel Tel 31 344 63 45 40 Fax 31 344 62 33 61 Email informatie anatomicsitt com Be Independent Ltd St Luke s Road G Mangia PTA MLT 1027 Tel 356 214 662 66 Fax 356 214 656 70 Consolor Ltd Unit A3 The Forelle Centre Black Moor Road Ebblake Industrial Estate Verwood Dorset BH31 6BB Tel 44 120 282 76 50 Fax 44 133 273 02 33 HandiTech Scandinavian Reha Aids Center 11 G Seferi Str GR 542 50 Thessaloniki Tel 302 310 324 114 Fax 302 310 324 054 Email info handitech gr Inv
13. e seatplate There is tvvo positions for depht adjustment Tighten the screvvs B on both sides vvith vvasher and nuts C Notel A Before installation you have to remove the seal from the seatplates Then you can easily insert the footrest attachment Safety stop A pin D is installed in the bottom of the footrest attackment The pin can also be used to find back to a pre set height position Tips Install an additional pin above the footrest in the footrest attachment to easily find your way back to an alternative height position eg with or without shoes Adjusting the angle on the knee joint When the footrest attachment is installed to the chassis you can adjust the footrest angle at the knee joint Loosen the screw E slightly and adjust to the desired angle Tighten the screw Adjustment the height of the footrest When the footrest attachment is installed to the chassis you can adjust the heght of the footrest Loosen the adjuster F and adjust to required height Tighten the adjuster Anatomic SITT AB User manual Zitzi Guppy 21 Calf support Mounting of calf support Install the calf support vvith the supplied screvvs and pins as illustrated into the footrest attachment Height adjustment of the calf support Loosen the screws A slightly and then adjust to the required height Tighten the screws A Widht adjustment of the calf support Loosen the screws B slightly and then adjust to the required widh
14. g o ooo oeooueoeooeuee 14 Caster fork position scsse esee 15 Angle adjustment of caster forle 15 Brake 5o o eumd erts 17 Dt rn brake u 17 Setting the brakes metta 17 Releasing the brakes ss 17 Troubleshooting of the brakes 17 Installation of drum bralee 19 Parking brahe e 20 Installation of parking brake 20 Using the parking brake 20 Footrest 0 21 Mounting of footrest eeenene 21 Safety StOD c cei nenne 21 Adjusting the angle on the knee joint 21 Adjustment the height of the footrest 21 Calfsu pporree 22 Mounting of calf support 22 Height adjustment of the calf support 22 Width adjustment of the calf support 22 Anti tip device 23 Installation of anti tip device 23 Using the anti tip device 23 Step bar cocer tec ende 24 Installation of the step bar 24 Using the step bar eenneen 24 Transportation kit 26 Installation of front bracket 26 Installation of rear bracket
15. g Ret ee 33 Ret rning products eo rtt o e e Re 37 Reconditioning 34 Customer service 38 Ser VIGCG naeh 34 Cleaning sce edistuetrmeci aeria iatis ad 34 Technical data ree 39 Finishing en 34 Marking crore tre REPRE REN RUE 34 Wheels au 34 Anatomic SITT AB User manual Zitzi Guppy 5 Seat part Installation of the mounting plate The seating system mounting plate is easily mounted on the chassis by four 4 screws washers and nuts in selected tracks A on the chassis seatplate Place the seating systems mounting plate B on the chassis seatplate C and stick through the supplied screw D Then meet up with nut and washer F on the underside of its chassis seatplate Tighten the screws D firmly A Note The picture shows only one type of mounting plate assembly instructions For more information about mounting plates see the instruction manuals for se lected seating system Anatomic SITT AB User manual Zitzi Guppy 6 Tilt Tilt the seat The seatplate is adjustable at an angle between 0 32 Press the tilt handle A while holding the handle and pushing it upwards or downwards Let go of the tilt handle A when the seat is in the required position To restore the angle to its neutral position press the tilt handle A and push the handle upwards and backwards A Obs Be careful to
16. king Zitzi Guppy and its accessories are CE marked products A unique serial num ber is located on a label placed under the activation housing This serial number should be quoted in any correspondence regarding the product Recycling A used part or product should be dismantled and discarded The parts should be separated by material type metal plastic and combustibles textiles Gas piston is sorted as hazardous material A Noticel Always check that the device is not customized when reconditioning before it is sent to new users Anatomic SITT AB User manual Zitzi Guppy 33 Reconditioning Service Regular maintenance is important for the Guppy to funcion safe and properly The need for service changes is dependending on use and wear Check all moving parts and fasteners regularly Useoriginal parts from Anatomic SITT AB when reconditioning the Guppy Work should always be done by professional and qualified staff If you need support you are always welcome to contact Anatomic SITT AB The need of reconditioning varies and must be judged case by case Go through all checkpoints at least once per year or as needed Functional control should be performed each time the Guppy is used Cleaning Painted surfaces wheels front castors and handles is cleaned with cleaning solvent Never use paint thinner gasoline or other solvent Finishing After washing all leads confined space and drainage holes should be blown d
17. o press all the way to the driving handle About 5 10 mm s should remain when brakes are set Repeat the procedure with the left brakehandle Setting the brakes Press the brakehandle A and push the red locking device B forward Releasing the brakes Press the brakehandle A and the locking device will release automatically Then let go of the brakehandle If the brakes does not work Check the tension of both brakewires If a wire has low tension try to tens it by loosen the screw C and then tighten again If the adjustment is not enough try the following quick setup guide to re tighten the brake cables 1 Tighten the screw C to its bottom position 2 Loosen the nut D 3 Squeeze the brake by lifting the drum brake arm E and move the nut D further up the wire 4 Tighten the nut D and adjust the tension with the screw C Anatomic SITT AB User manual Zitzi Guppy 17 Anatomic SITT AB User manual Zitzi Guppy 18 Brake Installation of drum brake You need to remove the wheel from the wheelchair to mount the drum brake Press the button on the quick realease axle and pull the wheel and axle out from the drum brake See page 12 Mount the drum brakes on the chassis by threading the large distance A to the drum brake attachment as illustrated Secure the large distance A with the large nut B as illustrated It is important to not tighten too hard Then take the screw C and put it in
18. om info anatomicsitt com facebook com anatomicsitt youtube com anatomicsitt J SITT User manual Zitzi Guppy 40
19. pull off the wheel from the chassis Anatomic SITT AB User manual Zitzi Guppy 12 Driving wheels Wheel position Depending on the seating systems position on the chassis seatplate you can adjust the wheel horizontally to maintain a correct centre of gravity and better balance To adjust the wheel in the right position release the four screws A underneath the wheel axle and adjust to the required depht Secure and measure that the wheel axle is on the same depht on both sides 16 wheels are mounted i the provided holes B C 20 22 and 24 are mounted in the provided holes D E For advice and help balancing the wheelchair please contact your dealer Notice NOTE that changing the wheelposition might increase the risk of tipping gt Notice The screws should not be taken out completey Just loosen them a little gt Anatomic SITT AB User manual Zitzi Guppy 13 Caster Installation of caster Insert the pin A underneath the chassis as illustrated Then mount the front wheel house K using screw B washer C and the eccentric nut D and tighten Mounting of the caster on the caster house fork Mount the caster F into one of five different positions by using the caster fork K the supplied axle G washer H and lock nut I Place the caster F in the caster fork K Provide the axle G with a washer H and lead the axle into one of the five provided holes and the c
20. ry and spray lubricated with thin oil Marking Check that the CE marking is intact and readable The marking is located on the tubular frame Wheels Make sure both castors and rear wheels are not worn and that they spin easily without noise See page 14 21 of this manual for further information regarding wheel and caster adjustment Paint To prevent corrosion and touch up scratches check for damages in the paint If needed touch up paint is available from Anatomic SITT AB Anatomic SITT AB User manual Zitzi Guppy 34 Stability Check that all the wheels are firmly on the ground and that there is no skewness in the chassis See page 14 21 of this manual for further information about vvheel and castor adjustment Tubular frame and details Welded and bolted joints Grind bushings and hinges to operate without noise Lubricate as required Also check the knobs screws and other mounting parts Replace them if necessary Forks Ensure that the fixings and bearings no play and they turn easily Lubricate the front forks when needed Driving bow and push handle Make sure the padding and handles are secure and that the push handle is adjustable in height Also check the condition of the knob and screw Brakes Check that the drum brake and parking brake are working properly Additional information about the brakes see page 22 27 of this manual Folding mechanism and tilt Make sure that you can easily fol
21. t Tighten the screws B Anatomic SITT AB User manual Zitzi Guppy 22 Anti tip device Installation of anti tip device Install the anti tip device on the wheel axle as illustrated using the supplied screws A washer B nuts C and nut cover D Insert the screw A into the holes on the anti tip attachment and through the chassis and put a washer B and nut C on the opposite side Tighten the screws Finish by placing nut covers D as illustrated Note A Zitzi Guppy should always be equipped with anti tip device because of its many adjustment possibilities Using the anti tip device The anti tip should be used for a safer and secure usage of the chassis It can easily be folded when not in use by carefully stepping down the anti tip and turn it aside When deactivating try to step on the anti tip so close the anti tip at tachment as possible Make sure to turn the anti tip advice until you hear a click wich indicates that the anti tip is in its right position Anatomic SITT AB User manual Zitzi Guppy 23 Step bar Insallation of the step bar Install the step bar A on the inside of the chassis as illustrated Thread the nuts in the track and lock its position with the screws B from the outside A Note The step bar is assembled on the right side as standard Using the step bar The step bar facilitate the raising of the chassis when it is necessary
22. tal address Anatomic SITT AB Box 6137 SE 600 06 Norrk ping Street address Anatomic SITT AB Terminalgatan 1 SE 603 61 Norrk ping Telephone 4611 161800 Fax 4611 162005 Email info anatomicsitt com Web anatomicsitt com youtube com anatomicsitt Anatomic SITT AB User manual Zitzi Guppy 3 Anatomic SITT AB Table of contents Safety precautions 3 Introduction sssini ri prann eee i teens 3 Seat part anne 6 Mounting of the seatplate 6 Tall a ee 7 Tiltof the Seat seen 7 An 9 Installation on chassis ete 9 Height adjustment 9 Width adjustement ssss 9 Angle adjustment upwards and downwards 9 Depth adjustment ssssR 9 Driving handle 11 Installation of driving handle 11 Depth adjustment of the driving handle 11 Angle adjustment of the driving handle 11 Angle adjustment of driving handle 11 Fold the driving handle 11 Wheels with Quick release 12 Mounting of wheels with quick release 12 Release the wheel nn 12 Driving vvheels 13 Wheel POSITION u tn 13 Caste dies 14 Installation of caster e e 14 Mounting of the caster on the caster house fark 14 Caster positionin
23. the ellipticall hole and thread the small dis tance D over the screw C Fasten the screw C using a washer E nut F as illustrated Tighten the both nuts B and F Make sure the drum brake i properly positioned Put the wheel back on the wheelchair page 12 when the installation of the drum brake is done Obs A Nut B and screw C when selecting 16 wheels has to be secured with a thread lock such as Loctite 243 or similar Note A When selecting the 16 wheels the screw C is threaded directly in the plate N Note For more information on how to use the quick release see page 12 Note A The installation of the drum brake is the same for all wheel sizes Anatomic SITT AB User manual Zitzi Guppy 19 Parking brahe Installation of handbrake The installation of the parking brake attachment should be installed as illustrat ed in the intended hole pattern on the chassis side with the supplied screws A washers B and nuts C Adjust the handbrake D if necessary by loosen the screws E and then move the handbrake forward and backwards in the track Tighten the screws E when required position is reached Using the handbrake Set the handbrake D by pressing the handbrake arm forward Pull the arm back to release the handbrake Anatomic SITT AB User manual Zitzi Guppy 20 Footrest Mounting of footrest Insert the footrest attachment A in the front holes underneath th
24. the seat loosen the screws B underneath the seatplate on the roar of the chassis and adjust to the desired depht Tighten the screws B A Noticel The screw must fit into one of the four fixed positions that is available on the driving handle Angle adjustment of the driving handle You can adjust the angle according to the seating system you are provided vvith Release the the adjusters C on both sides Adjust the push frame to required angle and then tighten the adjusters C Noticel A The driving handle shall always be in contact with the back of the seating system during transportation in a vehicle Angle adjustment of driving handle Press the buttons D on the inside of the driving handle and adjust Fold the push frame Release the adjusters C and fold the push frame forewards Tighten the adjusters C Anatomic SITT AB User manual Zitzi Guppy 11 Wheels with Quick release Mounting of wheels with quick release The wheels can easily be removed from the chassis which can be useful during transport purposes Press and hold the button B in the wheel center Push the wheel A until it stops Release the press button B Secure that the wheel is installated properly by trying to pull it outwards without pressing the quick release button B A Noticel Secure that the wheel is installated properly by trying to pull it outwards Release the wheel Press and hold the button B in the wheel center as you
25. ts and fasteners for wear Service should always be performed by professional and qualified personnel If you are unsure please feel free to contact Anatomic SITT AB Cleaning and washing instructions Plastic and metal parts can be wiped off with a damp cloth or washed with antibacterial liquid or similar Think green think about the environment Use biodegradable detergents Check the condition regularly and perform maintenance when necessary Gas piston Gas piston should be used regularly to maintain its function If the product is not used the gas piston should be activated at least once every 6 months Further they should be stored so that the piston rod is placed facing downward Otherwise the gas spring seal might break and the gas piston fail T Note Gas piston must be activated regularly Anatomic SITT AB User manual Zitzi Guppy 32 Warranty 1 year against manufacturing defects For more detailed information about the warranty we provide see page 49 of this manual Combinations Zitzi Guppy and its accessories are CE marked products that can be combined with all the accessories described in this manual Zitzi Guppy is suit able for use together with seating systems like Zitzi Delfi Pro and Anatomic Sits For other combinations please contact Anatomic SITT AB Spare parts For the CE marking of the Zitzi Guppy to be valid the frame may only be fitted with spare parts delivered by Anatomic SITT AB Mar
Download Pdf Manuals
Related Search