Table Of Contents Pdf

Home

1. 1 2 3 4 Start the AiO Home Center Click to open the Help panel Under General Links click Maintenance Click Printhead Cleaning To clean printhead from control panel 1 2 3 4 Press Menu to display the Main Menu Press w until Clean Printhead is selected Press OK to go to the Clean Printhead menu Press OK to perform a Basic Clean Or Press w to select Deep Clean and press OK to perform a Deep Clean Replace Printhead 1 Make sure the EasyShare AiO is on 2 Open the printer access door The carriage moves to a center position 74 Kodak EasyShare 5300 AiO Maintenance 3 Wait until the printhead is idle and silent then pinch the pinch latch on the ink cartridge with your thumb and forefinger and lift it out of the print head Remove both ink cartridges 6 Remove the printhead from its bag 7 Remove and discard the clear plastic casing and the orange protective cap User s Guide EN 75 Chapter 7 8 Place the printhead into the carriage Ez gt D P P 10 Reinstall the ink cartridges 76 Kodak EasyShare 5300 AiO Support If you have a problem with your AiO printer refer to the Troubleshooting topics in this book Additional technical information is available in the ReadMe file located on the Kodak EasyShare software CD For online support visit www kodak com go support Contact Kodak Resource Center www kodak com go resourcecenter Get support for your pr
2. 5 Press Start to print 54 Kodak EasyShare 5300 AiO Print User s Guide EN 55 Copy The Kodak EasyShare AiO allows you to produce high quality color and black and white copies on a variety of paper types including transparencies Once copying has started you may at any time abort a copy operation by pressing the Cancel button Copy with Control Panel Pressing Copy displays the copy menu where you can set copy options preview copies after scanning and make copies When copying from the Control Panel you can choose from the following outputs Same Size The copy is the same size as the original Cropping will occur if the original is larger than the paper size The copy will contain white space if the original is smaller than the paper size Same Size is the default copy setting Fit to Page The image is copied and fit to the paper size loaded There may be cropping on the sides or top bottom depending on the difference in the aspect ratios of the image and the page size Scale Percent The default copy scale is 100 however you can scale copies from 10 to 500 Scaling is anchored to the upper left corner of the original Photo Layouts You can set the layout for making copies of photos on your Kodak EasyShare All in One The following layouts are supported Borderless default Bordered 2 per Page 3 per Page 4 per Page 9 per Page 2x2 Poster 3x3 Poster 4x4 Poster User s Guide 57 Chapter 5 Same
3. Kodak EasyShare 5300 All in One Printer User s Guide Kodak Eastman Kodak Company Rochester New York 14650 Eastman Kodak Company 2008 P N 1K3234 Kodak and EasyShare are trademarks of Eastman Kodak Company The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks is under license 1989 2007 I R I S Image Recognition Integrated Systems All Rights Reserved Table of Contents PAA NNN 1 ME e o a 1 CONTO Pa til 2 NN NN 3 EDEN PN 8 Memory Card Slots ana USB POr eternal 9 AIO HOME Center VICO WS ba 10 AIO Home Center NNN Serer ete ace an na 11 Gems SN 13 Fono OE E mesma older 13 fee Nad eal Uh ee ee en NN ten 13 Jee Maa ada On seme EEE dr ORI 15 Stall tie Re 16 SOU Ep VEE Eee dene cae KD T 17 en nnti 18 Bl eg See NN NN NN EN 21 Tr A A 22 Onn Unie MN 22 Randine nd Loadine Pires 27 Ve MN ts llanta 27 Had a Nu ION stat 28 Kors le elg OS sn EE a NN PA AA On NAN RA ee PA tee cre ANN 30 1040 Ar rana a 31 A See 32 Ed 33 Adaa MOCO Solr NN 34 Pun Rote iron le Sono Pane e 34 FENCES TE 35 Prot Photos fonra ooh Pn nan nan nat 36 TAP E EE 36 EE OTe PAN e srta 37 FN NNN 38 LAVOUTS PPP uo o oo die 38 SSO Go a e a POE o OM CEE e E ORO A 50 FM 52 ENN 57 Copy Win Control Pane besitos So 57 User s Guide Table of Contents NNN 65 Scan Win Cono EE 65 Manten va 69 ELTERE 69 A CaN E E TA a EE TANN 70 CEG CINE canner desa 70 Formac oo be ne
4. Kodak EasyShare 5300 AiO Support Check the paper Disengage the photo tray if engaged Check the paper access on the back of the printer Remove any loose paper from the printer Inspect the paper supplies and reload with new paper if necessary Carefully fan the paper to keep the sheets from sticking together Reload the paper trays Do not overload ND OI FP Mech Re engage the photo tray if desired and then press Start to resume printing Slow Printing NOTE When printing a large number of prints printing may slow down to prevent the print head from overheating E Make sure the printer is not placed in direct sunlight or is not operating in a high temperature environment higher than 95 F or 35 C mM Close unnecessary software applications m Make sure your computer meets the minimum system requirements Upgrade your system if necessary White Edges on Borderless Prints Probable Cause White edges can appear when there are slight misalignments between the printer and paper Some software applications are able to hide these small misalignments so that the prints look borderless like they are supposed to Corrective Action Use the application s Fit to Page Fill Page option or resize the picture so it is slightly larger than the Daper size Copy Troubleshooting Copies Faded or Dull Colors Probable Cause 1 The copy quality is set to Draft Set the copy quality to Normal or Best See Set Co
5. Yes User s Guide EN dor dor dor dor dor Getting Started 2006 2099 January December 1 31 0 24 0 60 19 Chapter 2 Copy Button Quantity 4 or 1 99 Color dor Black amp White Quality d or Normal Draft Best Output d or Same Size Fit to Page Scale Percent Photo Layouts Size d or Output Scale Percent 10 500 Output Photo Layouts Borderless Bordered 2 per Page 3 per Page 4 per Page 9 per Page Index 2x2 Poster 3x3 Poster 4x4 Poster Brightness dor 3 to 3 Preview 4d or No Yes Photo Layouts only Save Settings dor No Yes 20 Kodak EasyShare 5300 AiO Getting Started Scan Button Scan What 4d or Document Photo Scan To d or File Application Memory Card Application dor gt List of applications Save Settings 4d or No Yes Help Button Installing Ink OK Cartridges Making a Copy OK Making a Photo OK Making a Scan OK Calibrating OK Printer Demo Sheet You can print a sample page on US Letter or A4 size paper to evaluate print quality The Demo Sheet is a single sheet of paper that displays information about the features and capabilities of your EasyShare AiO printer You can print a Demo Sheet by pressing the Copy and Photo buttons at the same time or Press Menu to display the main menu Press w until Print Demo Sheet is selected Press OK RR O N Press Start to begin printing User s Guide EN 21 Chapter
6. 40 Kodak EasyShare 5300 AiO Print 3 5x5 Inch Paper 1 per page borderless 1 per page bordered 2 per page 1 7x2 5 3 per page 4 per page 9 per page User s Guide EN 41 Chapter 4 4x6 Inch Paper 1 per page borderless 1 per page bordered 2 per page 3 per page 4 per page 9 per page 42 Kodak EasyShare 5300 AiO Print 5x7 Inch Paper 1 per page borderless 1 per page bordered 2 per page 3 per page 4 per page 9 per page User s Guide EN 43 Chapter 4 8x10 Inch Paper 1 per page borderless 1 per page bordered 2 per page 3 per page 4 per page 9 per page 44 Kodak EasyShare 5300 AiO Print US Letter 1 per page borderless 1 per page bordered 3 per page User s Guide EN 45 Chapter 4 46 Panoramic Kodak EasyShare 5300 AiO Print A4 Paper 1 per page borderless 1 per page bordered 2 per page 3 per page 4 per page 9 per page User s Guide EN 47 Chapter 4 A5 Paper 1 per page borderless 1 per page bordered 2 per page 3 per page 4 per page 9 per page 48 Kodak EasyShare 5300 AiO Print A6 Paper 1 per page borderless 1 per page bordered 2 per page 3 per page 4 per page 9 per page User s Guide CEN 49 Chapter 4 B5 Paper 1 per page borderless 1 per page bordered 2 per page 3 per page A per page 9 per page Setting Print Options Before you print photos you may want to chang
7. All in One status information is displayed on the LCD After the startup is complete the EasyShare AiO enters the Copy mode unless a photo device is attached If a photo device is attached or memory card inserted the EasyShare AiO enters Photo mode User s Guide 17 Chapter 2 Menus The Kodak EasyShare AiO menus are accessed by the Menu Photo Copy Scan and Help buttons Menu Button Help OK Inserting Ink Cartridges Making a Copy Printing a Photo Making a Scan Calibrating Printer Photo Print Settings OK Use Print Order if Found 4d or Yes No Scene Balance d or On Off Add Date to Prints dor No Yes Control Panel Settings OK Button Sounds 4d or On Off Minutes to Standby d or 10 30 Ink Levels OK Proofsheet OK Print Proofsheet Scan Proofsheet Clean Printhead OK Basic Clean Deep Clean Calibrate Printer OK Print Calibration Page Scan Calibration Page Format Memory Card OK Formats inserted memory card Print Demo Sheet OK Prints a demonstration page Print Diagnostic Sheet OK Prints a diagnostic page 18 Kodak EasyShare 5300 AiO Date and Time OK Year Month Day Hour Minute Language or list of languages gt Reset all Settings OK Photo Button Layout 4d or Borderless Bordered 2 per Page 3 per Page 4 per Page 9 per Page Index 2x2 Poster 3x3 Poster 4x4 Poster Quantity d or 1 99 Color d or Color Black 8 White Quality d or Normal Best Draft Save Settings 4d or No
8. Notice to Users in the European Economic Area The Kodak EasyShare All in One is designed to function with analogue telephone networks in the following countries Finland Netherlands Switzerland Network compatibility depends on customer selected settings which must be reset to use the equipment on a telephone network in a country other than where the product was purchased Contact the vendor or Eastman Kodak Company if additional product support is necessary 96 Kodak EasyShare 5300 AiO Appendix This equipment has been certified by the manufacturer in accordance with Directive 1999 5 EC Annex ID for Pan European single terminal connection to the public switched telephone network PSTN However due to differences between the individual PSTNs provided in different countries the approval does not of itself give an unconditional assurance of successful operation on every PSTN network termination point In the event of problems you should contact your equipment supplier in the first instance This equipment is designed for DI MF tone dialing and loop disconnect dialing In the unlikely event of problems with loop disconnect dialing it is recommended to use this equipment only with the DTMF tone dial setting User s Guide EN 97 Chapter 9 98 Kodak EasyShare 5300 AiO Glossary ADF Automatic Document Feeder AES Advanced Encryption Standard C CHAP Challenge Handshake Authentication Protocol D dBa Decibel meas
9. Pictures and Documents Copy Pictures Print Pictures Configure Settings for Printing and Scanning Access My Resource Center at Kodak Order Supplies There are three small icons in the upper right corner of the window isi Returns you to the main Home Center screen Displays the Status Monitor Displays a Help panel for the Home Center software 10 Kodak EasyShare 5300 AiO Product Overview AiO Home Center Macintosh The AiO Home Center software is an application that runs on the computer It enables you to configure your AiO printer from the computer After installation you can run Home Center from the Printer Setup Utility by selecting your Kodak AiO Printer in the Printer List and clicking the Utility icon The Setup and Maintenance tabs let you E Configure Settings E Calibration and Printhead Cleaning Select Provides a list of connected printers where you can select another printer Order Supplies Connects you to a Kodak web site where you can order supplies online View Hide Status Opens a drawer that displays the configuration status of your Kodak AiO printer User s Guide EN 11 Chapter 1 12 Kodak EasyShare 5300 AiO Getting Started It is important to find a good location for your AiO Printer Place the printer on a clean flat surface in a dry location and out of direct sunlight Make sure the printer has proper ventilation Avoid areas where ventilation ducts open doors or high traffic
10. Size Copy The copy is the same size as the original and is the default copy setting Cropping will occur if the original is larger than the paper size The copy will contain white space if the original is smaller than the paper size 1 Load your original face down on the right front corner of the scanner glass Press Copy to display the Copy menu Press w to select Output Press d or to select Same Size a RR W N If desired make changes to the following copy options with the Copy menu See Set Number of Copies See Set Color See Set Quality See Change Brightness See Set Preview 6 Press Start If you turned preview on the EasyShare AiO enters Preview mode otherwise it starts making copies 58 Kodak EasyShare 5300 AiO Copy Fit to Page Copy The image is copied and fit to the paper size loaded There may be cropping on the sides or top bottom depending on the difference in the aspect ratios of the image and the page size 1 Place your original face down on the right front corner of the scanner glass Press Copy to display the Copy menu Press w to select Output Press d or P to select Fit to Page a fF O N If desired make changes to the following copy options with the Copy menu See Set Number of Copies See Set Color See Set Quality See Change Brightness See Set Preview 6 Press Start If you turned preview on the EasyShare AiO enters Preview mode otherwise it starts making copies User s
11. ami 70 PHARD HOS IE KA cameron ee eter et tee EE ER 70 A Un 71 NETT A 71 Seit et 73 UPP 77 A ene ORE EN eo en A 77 Reie ele EE 77 Telephone Customer SUPPO Te 79 REN 80 APP Ik NG 91 An One Specitica tiOrS ka GANGE 91 Computer e EN RE 91 PENN eer ine reece een eter etre errr eee eee 92 NE EE EE TEE EE EE AN NE EEE EN PERE DN ERE ERE PERE EE 94 RAN su 6 KE aleet 95 Ne 99 ME NNN 101 ji Kodak EasyShare 5300 AiO Product Overview The Kodak EasyShare 5300 All in One AiO Printer allows you to print copy and scan photos or documents Many functions can be operated directly from the Control Panel You can buy optional accessories to enhance your Kodak EasyShare AiO experience Main Components Scanner lid LCD display Control panel Printer access door Memory card indicator Memory card slots USB port Photo tray Light Photo tray O O N OO OF FP AJ N User s Guide EN 10 11 12 13 14 15 16 17 Paper length guide Main tray Output tray extender Paper width guide Output tray Rear access door Power connector USB port Chapter 1 Control Panel Layout 18 17 16 15 14 13 12 11 LCD display Displays photos messages status and menus When in Photo Preview mode magnifies the photo to 1 5X Subsequent Zoom button presses zoom in 0 5X increments to a maximum of 5X When in Multiview displays the current photo in preview mode Proofsheet When there are pictures on an ins
12. in One can access the memory cards used in most digital cameras You can insert the memory card into the EasyShare AiO or connect your camera directly through one of the two USB ports on the front panel using a USB cable Your Kodak EasyShare AiO can read the contents of the memory card while it is still in the camera If your EasyShare AiO beeps three times when you plug a device into the USB Port it means the device is not supported User s Guide 9 Chapter 1 Supported Memory Cards Your Kodak EasyShare AiO can read the following memory cards xD Picture Card Memory Stick Memory Stick Pro Secure Digital Card MultiMediaCard Compact Flash type and type II including microdrives Your EasyShare AiO also supports the following memory cards with Memory Stick and SD MMC card slot adapters you can purchase E Memory Stick Duo E miniSD mM MicroSD TransFlash The Memory Card light is a green LED located near the memory card slots It lights whenever you insert a memory card and flashes while the care is being read The flashing serves as an indication to not remove the card while it is being read or written to which could potentially damage the data on the card AiO Home Center Windows The AiO Home Center software is an application that runs on the computer It enables you to print copy scan and configure your AiO printer from the computer The six large icons on the AiO Home Center main window let you Scan
13. is selected Press OK Press Start to begin formatting a fF N Print Diagnostic Sheet The Diagnostic Page contains information about your printer that can be useful when contacting Kodak Support 1 Press Menu 2 Press w until Print Diagnostic Sheet is selected 3 Press OK 70 Kodak EasyShare 5300 AiO Maintenance 4 Press Start to begin printing Firmware Upgrade You can update the firmware in your EasyShare AiO with the most recent available from the Home Center software This requires an internet connection 1 Click the Help button to open the Help panel 2 Under General Links click Maintenance 3 Click Firmware Upgrade Ink Cartridges Your Kodak EasyShare AiO uses separate black and color ink cartridges The ink levels are displayed on the Control Panel and the printer software Generic or non Kodak ink cartridges may not function in the KODAK EASYSHARE All in One Printer Kodak recommends using Kodak ink cartridges Check Ink Levels You can easily check the ink levels to determine how soon you might need to replace an ink cartridge The ink level supply screen shows the amount of ink remaining in the ink tanks 1 Press Menu to display the main menu 2 Press w until Ink Levels is selected 3 Press OK to display the Ink Levels screen we E The Ink Levels screen shows ink levels in a vertical gauge format with one gauge for the Black Ink cartridge and one gauge for the Color Ink cartridge Replac
14. progressively across all pages of a multi page index print 8x10 Index prints are 7 8 inches wide with 1 8 inch white space between photos The filename is displayed below each thumbnail image Ax6 index prints are 3 4 inch wide with 1 8 inch white space between images The filename is displayed below each thumbnail image Insert a memory card into the appropriate slot a mass storage device into the USB port or connect a digital camera to the USB port The first photo is displayed AN WARNING A Never attempt to remove a memory card while it is being accessed Doing so can damage files on the card You can safely remove a card only when the status light next to the slots is not blinking Load the main tray see Load Main Tray in Chapter 3 or photo tray See Load Photo Tray in Chapter 3 with photo paper NOTE The Photo Tray only supports 4x6 inch and 100x150 mm photo paper 3 4 5 Press Photo The Print menu is displayed with Layout selected Press the or to select Index Press Start User s Guide EN 33 Chapter 4 Print Photos from a Proofsheet A proofsheet is a simple and convenient way to select photos and make prints directly from a camera or memory card without the need for a computer Proofsheet printing is a two step process In the first step you connect a PTP camera or insert a memory card and print a proofsheet In the second step you select pictures to print from the proofsheet and then scan the proof
15. the Day Press OK Press d or D to set the Hour Press OK Press d or D to set the Minute Press OK Kodak EasyShare 5300 AiO Set Language You can select the language the EasyShare AiO uses for the LCD display Press Menu to display the Main Menu Press w until Language is displayed Press OK to go to the Select Language menu Press w until the language you want is selected Press OK Reset All Settings a fF Q N You can restore the original factory settings to your Kodak EasyShare All in One NOTE Restoring the factory defaults will not change the date and time information you set 1 Press Menu to display the Main Menu 2 Press w until Reset All Settings is selected 3 Press OK User s Guide EN Getting Started 25 Chapter 2 26 Kodak EasyShare 5300 AiO Handling and Loading Paper Use the following guidelines when handling paper To avoid fingerprints handle the paper by the edges as much as possible Avoid touching the glossy side of photo paper Keep the input and 4x6 paper trays closed to keep out dust and debris Store paper flat Keep paper away from direct sunlight and out of high temperature environments such as a vehicle parked in the sun You can load many different types and sizes of paper in your Kodak EasyShare AiO including letter paper photo paper transparencies and envelopes see Paper Types in the Appendix The EasyShare AiO automatically detects the size and type of
16. walking left to right User s Guide 3 Chapter 1 Power Light on Power Cord Light Status Action Solution Power cord light is off Power cord light is on The printer to power supply cord is not properly connected to the Power Supply The power supply to your wall outlet cord is not properly connected to your wall outlet You do not have the appropriate power available at your wall outlet There may be an issue with the power supply The power cord and power supply are properly connected and ready to supply power to the printer Reseat the printer to power Supply cord Reseat the Power Supply to your Wall Outlet Cord Test your wall outlet by plugging a known working device into you wall outlet Have your wall outlet checked by a qualified electrician Visit Kodak com for additional troubleshooting steps or contact your local Kodak Call Center Ensure that the power cord is properly plugged into the back of the printer Kodak EasyShare 5300 AiO Product Overview On Off Light Light Status Action Solution Light is off The printer is turned off Press the On Off button to turn the printer on The Printer does not have power Check the light on the power applied cord The printer needs attention Check to see if the Photo Tray light is on If the Photo Tray light is on for more that 20 seconds and the On Off light does not come on disconnect the power for 5 seconds and reconnect the
17. 1x203 mm 4x12 in 101x305 mm 5x7 in 127x178 mm 6x9 in 152x229 mm 8x10 in 203x254 mm 8 5x11 in 216x280 mm A4 210x297 mm 3 5x5 25 in 89x133 mm 3 5x7 25 in 89x184 mm Greeting Card 4x5 5 in 101x140 mm 4x8 in 101x203 mm Hagaki 100x148 mm Photo User s Guide 93 Chapter 9 Safety E Read and follow these cautions and warnings before using KODAK products m Always follow basic safety procedures E Follow all warnings and instructions marked on the equipment CAUTION Do not disassemble this product there are no user serviceable Part s inside Refer servicing to Kodak qualified service personnel WARNING Keep out of reach of children Ink is harmful if swallowed CAUTION Unplug your EasyShare AiO from the power outlet and refer servicing to qualified service personnel if the power cord or plug is frayed or damaged the equipment gets wet or the equipment does not operate normally when the operating instructions are followed CAUTION The AC adapter power supply is equipped with 3 wire grounding type plugs If you cannot insert the plug into the power outlet contact an electrician to check or replace the power outlet CAUTION Do not plug the AC adapter into a household extension cord CAUTION For added protection from damage during a lightning storm or any time when your EasyShare AiO and its associated AC adapter will be left unused for long periods of time unplug the AC adapter f
18. 2 Transfer Photos After you take photos with your digital camera you can print them immediately or save them directly to your computer You can transfer from memory cards PTP cameras and USB mass storage devices 1 Insert a Memory Card into the appropriate slot or connect a camera to the USB Port EP T R EEE o AN WARNING Never attempt to remove a memory card while it is being accessed Doing so can damage files on the card You can safely remove a card only when the status light next to the slots is not blinking 2 Press Transfer 3 Press Start to transfer 4 Complete the transfer with the Transfer dialog on your computer Configuring Settings You can configure settings for your Kodak EasyShare AiO using the Control Panel and the AiO Home Center software Use Print Order if Found The Digital Print Order Format DPOF is an industry standard file that can be created by some digital cameras Camera selected photos are photos you tag for printing with your digital camera When you select photos with your camera the camera creates a DPOF file that identifies which photos have been tagged for printing Your Kodak EasyShare AiO can read the DPOF file from the memory card in a camera so you do not have to re select the photos to print NOTE Not all digital cameras allow you to tag your photos for printing See your digital camera documentation to see if it supports tagging DPOF When you print tagged photos the selected
19. Guide 59 Chapter 5 Scale Percent Copy The default copy scale is 100 however you can scale copies from 10 to 500 Scaling is anchored to the upper left corner of the original 1 Place your original face down on the right front corner of the scanner glass Press Copy to display the Copy menu Press w to select Output Press d or to select Scale Percent Press w to select Size Press d or to change the scaling NO On FP D See Set Number of Copies See Set Color See Set Quality See Change Brightness See Set Preview If desired make changes to the following copy options with the Copy menu 8 Press Start If you turned preview on the EasyShare AiO enters Preview mode otherwise it starts making copies 60 Kodak EasyShare 5300 AiO Photo Layout Copy Copy You can set the layout for making copies of photos on your Kodak EasyShare All in One The following layouts are supported NO Om Bb ND Borderless default Bordered 2 per Page 3 per Page 4 per Page 9 per Page 2x2 Poster 3x3 Poster 4x4 Poster Place your original face down on the right front corner of the scanner glass Press Copy to display the Copy menu Press w to select Output Press d or to select Photo Layouts Press w to select Size Press or to change the layout If desired make changes to the following copy options with the Copy menu See Set Number of Copies See Set Quality See Change Brig
20. N ab al eb obte el 89 Scan Document Control Panel 67 68 SCN PROTO EN EN AAN NN 65 66 Scan Problems sanam 88 89 NNN AAA aa ET 65 5 CAN la OG ER Ne et 70 NE 70 Scene Balance 23 SE O AA PPN 25 51 63 STEC RE 24 102 SHOW PU WAS tamatan 87 sje ee oa EE 91 NN na aa Kana 24 SUD 17 SUP PON EE 77 T Tagged lina desa sasak 22 Tagged PRO NS ass 36 NEIE 24 MA ee tei aetna 22 84 U USB POCE angeren e AAA AA An PA AA 9 W A 87 Z LO Mia 53 Zoom and Crop senin 64 1K3234 Kodak EasyShare 5300 AiO
21. Products if they fail to function properly during the warranty period subject to any conditions and or limitations stated herein Warranty service will include all labor as well as any necessary adjustments and or replacement parts If Kodak is unable to repair or replace a Product Kodak will at its option refund the purchase price paid for the Product provided the Product has been returned to User s Guide 77 Chapter 8 Kodak along with proof of the purchase price paid Repair replacement or refund of the purchase price are the sole remedies under this warranty If replacement parts are used in making repairs those parts may be remanufactured or may contain remanufactured materials If it is necessary to replace the entire Product it may be replaced with a remanufactured Product Remanufactured Products parts and materials are warranted for the remaining warranty term of the original Product or 90 days after the date of repair or replacement whichever is longer Limitations This warranty does not cover circumstances beyond Kodak s control This warranty does not apply when failure is due to shipping damage accident alteration modification unauthorized service misuse abuse use with incompatible accessories or attachments such as third party ink or ink tanks failure to follow Kodak s operation maintenance or repacking Instructions failure to use items supplied by Kodak such as adapters and cables or claims made after the
22. able Cause 1 The scanner glass is dirty Make sure the scanner glass is completely clean or the proofsheet might not scan properly see Clean the Scanner Glass Probable Cause 2 Memory Card or Camera Changed Make sure the same memory card inserted or camera connected you used to print the proofsheet Probable Cause 3 Proofsheet not place correctly on scanner glass Place the proofsheet on the front right of the scanner glass User s Guide EN 89 Chapter 8 90 Kodak EasyShare 5300 AiO Appendix All in One Specifications B amp W plain paper print speed Draft Normal Best 32 10 5 5 ppm Color plain paper print speed Draft Normal Best 22 6 3 ppm Photo print speed 4X6 Kodak Studio Gloss 2 14 ppm 28 sec print Photo print speed 8X10 Kodak Studio Gloss 0 86 ppm 70sec print B amp W plain paper copy speed Draft Normal Best 30 10 5 ppm Color plain paper copy speed Draft Normal Best 20 6 3ppm 18 8 W x 14 7 D x 8 8 H 47 8 x 37 3 x 22 4 cm Weight 21 3 lbs 9 7 kg Image Formats JPG EXIF V 2 21 Main Tray capacity 100 sheets of 20 Ib plain paper Photo Tray capacity 20 sheets of 10 mil thick 4x6 inch 101x150 mm photo paper Output Tray capacity 50 sheets of 20 Ib plain paper or 20 sheets of photo paper Product Operation Environmental Range 5 to 35 degrees C 15 to 85 RH non condensing and atmospheric pressure of no less than 15 PSI approximately 10 000 ft ASL Computer Requiremen
23. d turn it back on 2 3 If the problem still persists unplug the power cord from power supply and plug it back in If the problem continues to persist restart your computer User s Guide 83 Chapter 8 Transfer Pictures Failure Nothing happens when you try to transfer pictures to the computer Press the Transfer button on the printer Check the power and USB connections from the printer to the computer If you are trying to transfer pictures from a memory card and a PictBridge camera is connected remove it 4 Close unnecessary software applications and minimize remaining application windows Follow any messages on the screen that may have been hidden by other windows Disconnect then reconnect the USB cable from the printer to the computer Make sure you are using the USB cable included with your printer Make sure Kodak EasyShare software is installed Install if necessary If you choose Custom installation make sure to install the printer driver Un install and then reinstall Kodak EasyShare software 9 Make sure your computer meets the minimum system requirements Upgrade your system if necessary NOTE The Kodak AiO printer is compatible with the Kodak 8 in 1 card reader sold separately Other Kodak USB card readers may work with the printer however other manufacturers card readers are not supported Wrong Paper Size The paper you selected does not match the active paper tray The paper selected may be t
24. default layout is applied unless your camera allows selection of sizes The DPOF file is stored by the digital camera on a memory card and specifies the following information m Which photos to print HH The quantity of each photo to print E Index printing thumbnails of selected photos 22 Kodak EasyShare 5300 AiO Getting Started The default setting for using a detected DPOF file is Yes Press Menu to display the main menu Press w to select Photo Print Settings Press OK Press w to select Use Print Order if Found Press d or to change the setting Press OK oo HK W N dt Scene Balance Your EasyShare AiO is configurable to apply automatic scene balance improvements brightness for photos printed on the AiO from camera cards and USB connected devices The default is to apply the scene balance improvements Press Menu to display the main menu Press w to select Photo Print Settings Press OK Press w until Scene Balance is selected Press d or to enable or disable Scene Balance Press OK Add Date to Prints oo W N dt You can set your EasyShare AiO to print the date a picture was taken on the photo print The default is to not print the date Press Menu to display the main menu Press w to select Photo Print Settings Press OK Press w until Add Date to Prints is selected Press d or to enable or disable date printing Press OK O oo HK W N dt Button Sounds You can configure your EasySha
25. duration of this warranty KODAK MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY FOR THIS PRODUCT AND DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE In the event that the exclusion of any implied warranty is ineffective under the law the duration of the implied warranty will be one year from the purchase date or such longer period as required by law The option of repair replacement or refund is Kodak s only obligation Kodak will not be responsible for any special consequential or incidental damages resulting from the sale purchase or use of this product regardless of the cause Liability for any special consequential or incidental damages Cincluding but not limited to loss of revenue or profit downtime costs loss of the use of the equipment cost of substitute equipment facilities or services or claims of your customers for such damages resulting from the purchase use or failure of the Product regardless of cause or for breach of any written or implied warranty is expressly disclaimed Your Rights Some states or jurisdictions do not allow exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Some states or jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific rights and you may have other rights which vary from state to state o
26. e Ink Cartridges A Low Ink warning message is displayed when one of the ink levels drops below 20 percent NOTE For the best quality prints store ink cartridges in a location where the temperature does not exceed 85 F 30 C WARNING Generic or non Kodak ink cartridges may not function in the KODAK EASYSHARE All in One Printer Kodak recommends using Kodak ink cartridges Third party ink cartridges may not contain the necessary Smart Chip information to notify you before the ink cartridge is empty User s Guide 71 Chapter 7 1 Open the printer access door by lifting from the front center of the unit The ink tanks are located in the print head 1 Print head 2 Color ink cartridge 3 Black ink cartridge 2 Wait until the printhead is idle and silent then pinch the pinch latch on the old ink cartridge with your thumb and forefinger and lift it out of the print head voll 3 Open the box of the new ink cartridge Remove the bagged ink cartridge from the box and tear open the bag at the notch and remove the ink cartridge IMPORTANT Insert the ink cartridge immediately to prevent any drying of the ink 5 Remove the orange cap from the cartridge by grasping the top edge and pulling rotating it off the ink cartridge lt x ir A 72 Kodak EasyShare 5300 AiO Maintenance 6 Slide the ink cartridge into the printhead 8 Close the printer access door Printhead The printhead dispenses the ink from
27. e Will Not Print A selected picture does not print E The image file may be corrupt Review the picture on the camera or computer and delete if necessary E The image file may not be JPEG format The printer can only print JPEG files in standalone mode Connect to a computer and use EasyShare software to print BMP and TIFF formats Pictures Cropped m Change the picture quality setting or resolution on your digital camera to 3 2 See your camera user s guide for details m Adjust cropped pictures using Kodak EasyShare software on your computer mM If you are printing from an application on your computer select the proper paper size in print options NOTE Cropping may vary depending on the selected picture size Poor Print Quality 1 Clean the printhead 2 Runa calibration If the problem persists repeat as often as necessary Print Skewed or Slanted Probable Cause 1 The paper is not properly loaded in the tray 1 Remove the stack of paper from the main paper tray and slide the paper guides to the outermost position 2 Remove the paper and check for wrinkles and tears 3 Straighten the stack of paper against a flat surface and reload it into the main paper tray 4 Slide the paper width and paper length guides inward until they stop at the edges of the paper See Also Load Main Tray User s Guide 85 Chapter 8 Probable Cause 2 More than one type of paper is loaded Load only one type of paper Print Spott
28. e below shows the print sizes that result from the various layouts when applied to US Letter size paper 8 5 X 11 in A Paper Print Size 2 5x3 25 wallet In addition to US Letter size paper your EasyShare AiO provides photo layout support the following of US and ISO 216 paper sizes US sizes are measured in inches and ISO 216 sizes are based on the metric system US photo paper sizes m 3 5 X 5 inches m 4X 6 inches m 5X7 inches E 8X10 inches ISO 216 paper sizes E A4 21X 30 centimeters E A5 15X 21 centimeters m A6 10 X 15 centimeters m B5 17 6 X 25 centimeters The international paper size standard ISO 216 consists of an A series and a less common B series This standard has been adopted by all countries in the world except the United States and Canada The most widely used size in the ISO format is A4 The charts on the following pages compare the most common paper sizes 38 Kodak EasyShare 5300 AiO Simm 108 mm User s Guide CEN Letter IMA mn mf 3 Print 39 Chapter 4 62 mm 125 mm T T T D CIE A OOO i e i 1000 mm EEE B8 B5 Beal mm ml www 753 iiri a ge 176 frirti 1414 mm E E Pu CH e Set Print Layout 1 Press Photo The Print menu is displayed with Layout selected Press d or to change the print layout Press OK to set the selected layout and continue to set options press Photo to preview or Start to print
29. e print quality 3 Press OK to set the selected layout and continue to set options press Photo to preview or Start to print Save Settings When you change print settings from the control panel the settings apply only to the current print job To apply print settings to all future print jobs you can save the changes you make 1 Onthe Print menu select Save Settings 2 Press d or P to set to Yes 3 Press Photo to preview or Start to print User s Guide 51 Chapter 4 Previewing Photos The Print Preview screen contains a crop box displays the current photo number on the card or USB host device and the total number of photos on the card or device It displays a checkbox indicating whether or not the currently displayed photo has been selected for printing A checkmark is placed in the checkbox when the photo is selected along with the number of copies to be printed All photos selected are given the number of copies specified in the Quantity parameter on the Print menu by default For example if the Quantity parameter is set to 2 all selected photos are initially be given a number to print value of 2 Additionally the Print Preview screen displays an icon of a printer and the total number of photos to be printed For example if you select two photos each set to print 2 copies the number next to the printer icon will be 4 For every card USB host session a message is displayed the first time a photo is displayed instructing you t
30. e the following default settings m Layout Borderless E Quantity 1 print m Color Color print m Quality Normal E Save Settings No 50 Kodak EasyShare 5300 AiO Print The Photo Print menu contains parameters that allow you to specify other options Set Number of Prints You can increase the number of prints of each photo from the Photo Print menu The default is 1 print 1 Onthe Print menu select Quantity 2 Press d or to change the print quantity 3 Press OK to set the selected layout and continue to set options press Photo to preview or Start to print Set Color You can print in color or black and white Printing in color is the default 1 Onthe Print menu select Color 2 Press d or to change the print color 3 Press OK to set the selected layout and continue to set options press Photo to preview or Start to print Set Print Quality The Kodak EasyShare All in One provides three options that affect print speed and quality for plain paper Print quality is automatically set to Kodak Picture Quality when photo paper is detected Draft Produces the fastest print speed but the lowest quality Normal Delivers high quality output and is the default setting Normal prints faster than Best Best Produces the highest quality for all paper and eliminates the banding striping effect that sometimes occurs in solid areas Best is the slowest print speed 1 Onthe Print menu select Quality 2 Press d or to change th
31. ed Paper may be dirty Use adry lint free cloth to wipe clean For excessive dirt or debris thoroughly clean the paper tray and load new paper NOTE Keep paper tray covers closed to keep dust and debris from collecting on the paper or inside the printer Print Too Dark Try re taking the picture with the flash on or move within the flash range of the camera See your camera user s guide for details Adjust the exposure compensation on your camera and try re taking the picture See your camera user s guide for details Edit the picture using Kodak EasyShare software on your computer See the EasyShare software Help for details Make sure the printer is not placed in direct sunlight or is not operating in a high temperature environment Print Too Light IMPORTANT For best resulst use only Kodak Ink cartridges and paper for your printer Make sure the paper is loaded with the Kodak logo facing up Reload if necessary Try re taking the picture with the flash off See your camera user s guide for details Adjust the exposure compensation on your camera and try re taking the picture See your camera user s guide for details Edit the picture using Kodak EasyShare software on your computer See the EasyShare software Help for details Printing Stops Printing stops during mid print Paper stops feeding and Status light may blink IMPORTANT For best result use only Kodak Ink cartridges and paper for your printer 86
32. erted memory card or connected USB button host device pressing Proofsheet displays the Proofsheet menu Transfers images from device connected to a USB host port PictBridge or Picture Transfer Protocol PTP Green when Starting Up Ready or in Standby mode On Off Light Flashes red when in an error state Is not lit when in Sleep mode Transfer button N N Kodak EasyShare 5300 AiO Product Overview E pa Used to navigate Up Down w Left 4 and Right gt Menu button Displays the main menu screen Scan button Press to enter Scan mode Lit when in Scan mode Rotate button Rotates picture on the display clockwise 90 degrees When the EasyShare AiO is in Photo Preview mode pressing enters Multiview When a photo has been magnified with the Zoom button pressing decreases the magnification in 0 5X increments Zoom button mk N Status Lights The following tables contain information on the EasyShare AiO lights All Lights on Control Panel Light Status Action Solution All lights are off The printer is turned off Press the On Off button to turn the printer on The Printer does not have power Check the light on the power applied cord The On Off Light is flashing and The Printer is Initializing None Allow the Printer to the Display has the following complete the initialization message process Kodak EasyShare System Starting Up Please Wait The five boxes at the bottom are flash
33. f label sheets on top of standard paper in the input tray label side down 32 Kodak EasyShare 5300 AiO Print The memory card slots accept most of the popular memory cards see Supported Memory Cards When you insert a memory card into the card slot connect PTP camera or USB flash drive the last photo is displayed on the LCD display When you press the Photo button the Photo Print menu is displayed The Photo button toggles between displaying photos and the Photo Print menu CAUTION You can only use one device USB or Memory card from which to print If both devices are engaged the EasyShare AiO generates an error message When you print from an application the EasyShare AiO printer driver provides the following features Non photo Paper Print Quality Draft Produces the fastest print speed but the lowest quality Normal Delivers high quality output and is the default setting Normal prints faster than Best Best Produces the highest quality for all paper and eliminates the banding striping effect that sometimes occurs in solid areas Best is the slowest print speed Page Size You can select a standard page size or create a custom size Borderless Prints without any margin on the printed media Orientation You can print a document with the short edge of the paper at the top of the page portrait or with the long edge of the paper at the top of the page landscape Print last page first Causes printing to begin
34. g your photos for printing See your digital camera documentation to see if it supports tagging DPOF When you print tagged photos the selected default layout is applied unless your camera allows selection of sizes The DPOF file is stored by the digital camera on a memory card and specifies the following information Which photos to print The quantity of each photo to print Rotation applied to a photo Cropping applied to a photo Index printing thumbnails of selected photos 36 Kodak EasyShare 5300 AiO Print If a DPOF file is detected when you insert a memory card the EasyShare AiO displays a message asking if you want to print tagged images Bluetooth Printing Bluetooth is a short range radio technology that enables wireless connectivity between electronic devices This feature supports an optional Kodak USB Bluetooth Adapter that accepts JPEG EXIF image file types from the following types of Bluetooth enabled devices E Mobile camera phones f E PDAs VG A E Digital still cameras You can purchase a Bluetooth Adapter directly from Kodak at www kodak com go accessories To enable Bluetooth wireless connectivity plug your Kodak Bluetooth Adapter into the front USB port NOTE Your EasyShare AiO supports connection to only one Bluetooth device at a time and has an 8MB file size limitation Range The recommended maximum distance between Bluetooth devices for the highest transfer speed is 10 meters or 32 81 fee
35. htness See Set Preview Press Start If you turned preview on the EasyShare AiO enters Preview mode otherwise it starts making copies User s Guide 61 Chapter 5 Setting Copy Options You can set the following copy options with the Control Panel Copy menu Quantity Color Quality Output Size See Same Size Copy Fit to Page Copy Scale Percent Copy or Photo Layout Copy Brightness Preview Save Settings Set Number of Copies You can set the number of copies to make from the copy menu The default is 1 copy 1 Onthe Copy menu select Quantity 2 Press or hold or to change the number of copies you want to make 3 Press OK to set and continue setting options or Start to copy Set Color You can make copies if documents in color or black and white The default is color 1 Onthe Copy menu press w to select Color 2 Press d or to change the copy color 3 Press OK to set and continue setting options or Start to copy Set Quality Kodak picture quality is automatically selected when photo paper is detected in the main or photo input trays The Kodak EasyShare All in One provides three options that affect speed and quality for copying documents to plain paper Best Produces the highest quality for all paper and eliminates the banding striping effect that sometimes occurs in solid areas Normal Delivers high quality output and is the default setting Normal copies faster than Best Draft Produces
36. information go to www Kodak com go MSDS Regulatory Compliance FCC Compliance and Advisory FE Kodak EasyShare 5300 AO Printer This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed or used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on you are encouraged to try to correct the interference by one or more of the following measures 1 reorient or relocate the receiving antenna 2 increase the separation between the equipment and the receiver 3 connect the equipment to an outlet on a circuit different from that to which the receiver is connected 4 consult the dealer or an experienced radio TV technician for additional suggestions User s Guide 95 Chapter 9 Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Where shielded interface cables have been provided with the p
37. is not properly connected 1 Make sure the power cord is connected to the power supply and plugged into a grounded power outlet or power Strip If you are using a power strip make sure it is turned on If you are using a switched power outlet make sure the switch is on Make sure the power outlet is supplying power oF N If none of the above corrects the problem contact Kodak support 80 Kodak EasyShare 5300 AiO Support Bluetooth Device not Recognized Probable Cause 1 The internal Bluetooth radio in the device may be turned off Corrective Action Make sure the device is on and within range of the Bluetooth radio signal 30 ft or 10 meters NOTE The Bluetooth technology enabled device must use an BIP OPP or FTP profile Probable Cause 2 Sending device requires a PIN Corrective Action Enter a PIN of 1111 into the sending device Device not Recognized Any of the following can cause the prevent your Kodak EasyShare AiO from reading a connected digital camera or memory card The camera is turned OFF The USB connector from the camera is not fully inserted in the port The memory card is not completely inserted The memory card is in backwards The memory card file system is corrupt Correct any connection problems and try again If the memory card file system is corrupt reformat it in your camera Ink Cartridge Color Black Cartridge Not Recognized The ink cartridge installed was not recog
38. king could slow down performance and affect the accuracy of scanning This section covers the Settings menu printhead installation printhead calibration checking ink levels and changing ink cartridges General Care IMPORTANT Always disconnect the power before cleaning Do not use harsh or abrasive cleaners or organic solvents on the EasyShare AiO or any of its parts WARNING Do not leave items on the scanner glass The heat of the scanning lamp may cause them to stick To clean wipe the outside of the EasyShare AiO and LCD with a clean dry cloth Keep the surrounding area vacuumed and litter free Protect the EasyShare AiO from tobacco smoke dust sand and liquid spills Avoid placing objects on the EasyShare AiO Keep the EasyShare AiO accessories and supplies away from direct sunlight and out of high temperature environments Do not allow chemicals such as suntan lotion to come into contact with the painted surface of the EasyShare AiO mM If the EasyShare AiO has been subjected to inclement weather or you suspect water has gotten inside the EasyShare AiO turn it off and let it dry out If this does not resolve the problem contact customer support see Telephone Customer Support E Service agreements are available in some countries Contact a dealer of Kodak products for more information E For more disposal or recycling information contact your local authorities In the US visit the Electronics Industry A
39. l they stop at the edges of the paper User s Guide EN 29 Chapter 3 Load Photo Tray You can load up to 20 sheets of 10 mil thick 4x6 inch 101x150 mm photo paper into the photo tray TIP To avoid fingerprints handle the paper by the edges or by the perforated tabs Avoid touching the glossy side of the paper 1 Lift the photo tray lid 2 Slide the photo tray towards you until it stops NOTE When the photo tray is disengaged the main paper tray is active 3 Insert the stack of photo paper into the photo tray glossy side down 4 Slide the photo tray with the stack of photo paper in until it stops Engaging the photo tray turns the photo tray light on 30 Kodak EasyShare 5300 AiO Handling and Loading Paper 5 Close the photo tray lid Load Envelopes You can load plain envelopes into the main input tray of your Kodak EasyShare AiO Do not use envelopes with cutouts or cellophane windows 1 Lift the output tray 2 Remove any paper in the input tray 3 Insert one or more envelopes face down with the envelope flaps to the left 4 Slide the stack of envelopes forward until it stops 5 Slide the paper guides inward against the stack of envelopes until they stop User s Guide EN 31 Chapter 3 6 Close the output tray AE Load Labels Use letter or A4 designed for use with ink jet printers label sheets 1 Ensure that none of the pages are sticking together 2 Place a stack o
40. lliance Web site at www eiae org User s Guide 69 Chapter 7 Clean the Scanner Glass To ensure that your copies and scans remain clear keep the scanner glass and lid backing clean and dust the exterior 1 Turn off the EasyShare AiO and raise the lid 2 Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner AN WARNING Do not use abrasives acetone benzene or carbon tetrachloride on the glass since they can damage it Do not place or spray liguid directly on the glass The liguid might seep under the glass and damage the device 3 Dry the glass with a lint fee cloth Clean the Scanner Lid Minor debris can accumulate on the document backing located underneath the scanner lid of the Kodak EasyShare AiO 1 Turn off the EasyShare AiO and raise the lid 2 Clean the lid underside with a soft cloth or sponge slightly moistened with a mild soap and warm water 3 Wipe the underside gently to loosen debris Do not scrub 4 Dry the underside with a chamois or soft cloth WARNING Do not use paper based wipes as these might scratch the underside 5 If further cleaning is needed repeat the previous steps using isopropyl rubbing alcohol and wipe the underside thoroughly with a damp cloth to remove any residual alcohol Format Memory Card Formatting will erase all the data on a memory card Insert a memory card into the appropriate slot Press Menu Press w until Format Memory Card
41. might expose the EasyShare AiO and paper to high levels of dust and debris Airborne particles can affect picture quality Allow enough space on all sides of the EasyShare AiO to let you connect and disconnect cables change the ink cartridges and remove and load paper Connect Power Use only the AC power adapter included with your AiO printer Other adapters or cords could RISK OF ELECTRICAL SHOCK damage your printer or computer 1 Connect the printer power cord to the AC power adapter then to the back of the AiO printer 2 Plug the AC adapter power cord into a power outlet Install the Printhead The printhead dispenses the ink from the cartridges onto the paper 1 Make sure the EasyShare AiO is on 2 Open the printer access door The carriage moves to a center position User s Guide 13 Chapter 2 3 Remove the printhead from its bag 4 Remove and discard the clear plastic casing and the orange protective cap 5 Place the printhead into the carriage pe Be D F a 6 Push against the back wall of the printhead until it clicks into place 7 Install the ink cartridges Kodak EasyShare 5300 AiO Getting Started Install Ink Cartridges After installing the printhead you need to install the black and color ink cartridges 1 Printhead 2 Color ink cartridge 3 Black ink cartridge 1 Tear open the black ink cartridge bag at the notch and remove the ink cartridge IMPORTANT Insert the ink car
42. ngage if you want to print 4 x 6 inch pictures The printer is not turned on Press the On Off button to turn the printer on Photo tray light is On The photo tray is engaged Pull the photo tray out to disengage if you do not want to print 4 x 6 inch pictures The printer is powering up None Please wait and allow the printer to complete the initialization process If the flashing green persists you may have an issue with the printer Visit Kodak com for additional troubleshooting steps or contact your local Kodak Call Center 6 Kodak EasyShare 5300 AiO Product Overview Attention Light Light Status Action Solution Light is blinking steady Recoverable Error Paper jam while printing Main tray empty Photo tray empty Carrier stall during pick Media size mismatch Media type mismatch Paper jam during pick Carrier stall while printing Change color ink cartridge Change black ink cartridge Color ink cartridge not readable Black ink cartridge not readable Change both ink cartridges Printhead not calibrated Calibration sheet needs scanning Calibration sheet not detected Calibration sheet read error Back cover removed when idle Back cover removed while printing Unit opened when idle Unit opened during printing Too many picture sources Proofsheet not detected Proofsheet read error Light is blinking rapidly Warning Color ink cartridge inserted incorrectly Black ink cartridge inserted incor
43. nized Generic or non Kodak ink cartridges may not function in the KODAK EASYSHARE All in One Printer Kodak recommends using Kodak ink cartridges To correct the problem install a genuine Kodak ink cartridge Ink Cartridge out of Ink One of the ink cartridges has reached the end of its life and needs to be replaced To correct the problem replace the expired ink cartridge Multiple Paper Feed Multiple sheets of paper are pulled through printer User s Guide 81 Chapter 8 Disengage the Photo tray 2 Remove the paper from the paper tray s Carefully fan the paper to keep the sheets from sticking together 3 Reload the paper tray s Do not overfill 4 Re engaged the Photo tray then press Start to resume printing No Communication with Computer Your EasyShare AiO is not connected to your computer 1 Make sure you are using the proper USB Cable e pi 2 Check the connection from your computer to your AiO printer Ensure that the square end of the USB cable is plugged in to the USB port on the back of your AiO printer and the flat end into a USB port on your computer 3 You may need to disconnect other printers or scanners from your computer After checking connections restart your computer Make sure your computer meets the minimum system requirements Upgrade your system if necessary For more information on connecting your Kodak AiO printer to your computer see the Setup Poster that came with your
44. o press and to view the photos and to press OK to select the photo for printing For every card USB host session a message is displayed the first time you select a photo for printing instructing you to use and 4 to change the number of photos to print Preview Mode Preview mode allows you to select and edit photos for printing If you press the Start button while in Preview mode all the selected photos are printed If there are no photos selected then the photo displayed is printed Print preview mode is entered when you insert a memory card connect a camera or mass storage device or from Print mode by pressing Photo The Preview screen displays the current photo inside a crop box The crop box aspect ratio is 1 4 1 At the bottom of the screen the current photo number on the card or USB host device and the total number of photos is displayed A checkbox indicates whether or not the currently displayed photo has been selected for printing A checkmark is displayed in the checkbox if the photo has been selected along with the number of copies to be printed to the left of the checkbox All photos selected are given the number of copies specified in the Quantity parameter on the Print menu by default For example if the Quantity parameter is set to 2 all selected photos are initially given a number to print value of 2 Additionally the Print Preview screen displays an icon of a printer and the total number of photos to be printed F
45. oduct FAQs troubleshooting www kodak com go sfupport information etc Purchase full range of digital camera and printer www kodak com go accessories accessories Download latest printer software firmware and www kodak com go downloads drivers O Online tutorials www kodak com go howt Get information on EasyShare software www kodak com go easysharesw or click the Help button in the EasyShare software Get help with the Windows operating system and www kodak com go pcbasics working with digital pictures Get support for Kodak printers cameras software www kodak com go support accessories more Print a Diagnostics Page before contacting Kodak support see Print Diagnostic Sheet in the Maintenance chapter Register your printer www kodak com go register Limited Warranty Kodak warrants Kodak consumer electronic products and accessories Products excluding batteries to be free from malfunctions and defects in both materials and workmanship for one year from the date of purchase Retain the original dated sales receipt Proof of the date of purchase will be required with any request for warranty repair Limited Warranty Coverage Warranty service is only available from within the country where the Products were originally purchased You may be required to ship Products at your expense to the authorized service facility for the country where the Products were purchased Kodak will repair or replace
46. oo large or too small than the paper found in the paper tray 1 Replace the paper in the paper tray with the correct type 2 Press OK to continue or Cancel to exit Print Troubleshooting Envelope Printing Incorrect The envelopes are not loaded correctly 1 Remove the envelopes from the main paper tray 2 Straighten the stack of envelopes against a flat surface and reload it into the main paper tray 3 Slide the paper width and paper length guides inward until they stop at the edges of the envelopes Multiple page Document in Reverse Order The printing settings are set to print the first page of your document first Print the document in reverse order so the pages will be in the correct order when printing finishes 1 Clickthe Properties button on the Print dialog 2 Select Print last page first on the General tab 84 Kodak EasyShare 5300 AiO Support Photo Print Smudged Fingerprints may be on glossy side of paper Handle paper by the edges PictBridge Camera not Detected 1 Check the USB connections from the PictBridge compatible camera or device to the printer 2 If disconnected reconnect the USB cable from the PictBridge compatible camera or device to the printer 3 Make sure there is at least one picture in the PictBridge compatible camera or device s internal memory or memory card 4 Make sure the connected camera or device is PictBridge compatible See your camera or device user s guide for details Pictur
47. or example if you select 2 photos each set to print 2 copies the number next to the printer icon will be 4 IMPORTANT Crop zoom and quantity are per image but layout is global applying to all images 04 softs 52 Kodak EasyShare 5300 AiO Print Zoom Photos 1 Insert a memory card into the appropriate slot a mass storage device into the USB port or connect a digital camera to the USB port The first photo is displayed o0 of 16 2 Press Zoom to enlarge the photo in 25X increments up to 5X magnification Pressing Zoom decreases magnification in 25X increments down to 1X 4 Press OK when finished The photo is displayed with a crop box around the magnification and position you selected 01 of 18 i Fi 5 Press to select the number of prints and press Start to print the area displayed in the crop box User s Guide EN 53 Chapter 4 Multiview The Multiview screen shows thumbnails of nine photos The current photo number and the total photo number are also displayed 1 Inserta memory card into the appropriate slot a mass storage device into the USB port or connect a digital camera to the USB port The last photo is displayed 3 Use the 4 way Navigation button to move the red selection box to another photo Pressing when in the rightmost column displays the next Multiview screen Pressing when in the leftmost column displays the previous Multiview screen 01 17 of 27 1 Pd
48. paper you load in the input tray and then adjusts to generate the highest quality output for that paper The Scanner Glass The scanner glass is where you place originals for copying or scanning 1 Lift the lid and place your original face down on the right front corner of the scanner glass 2 Close the lid User s Guide 27 Chapter 3 You can copy or scan oversized originals by completely removing the lid from your EasyShare AiO To remove the lid lift the lid to the open position grasp the sides of the lid and then pull the lid upward Your EasyShare AiO functions normally with the lid removed Replace the lid by inserting the tabs on the hinge back into the appropriate slots Load Main Tray You can load the main paper tray with various types of paper from 3 to 8 5 inches wide and 5 to 14 inches long with a capacity of 100 sheets of 20 Ib plain paper clean stack of new paper IMPORTANT To print from the main paper tray make sure the photo tray is not engaged pulled all the way out and the lid closed 1 Lift the output tray and slide the paper width and paper length guides to their outermost positions 2 Align the edges of a stack of paper 3 Insert the stack of paper into the input tray with the short edge forward and the print side down Slide the stack of paper forward until it stops 28 Kodak EasyShare 5300 AiO Handling and Loading Paper 4 Slide the paper width and paper length guides inward unti
49. power If the Photo Tray light does not go out after 20 seconds and the On Off light comes on contact Kodak for assistance Light is a steady green The printer is properly powered None up on and ready Light is a flashing green The printer is busy None Normal operation when performing a print copy scan or other job requests The printer is initializing None Please wait and allow the printer to complete the initialization process about 30 seconds If the flashing green persists you may have an issue with the printer Visit Kodak com for additional troubleshooting steps or contact your local Kodak Call Center Light is a flashing yellow The printer has detected an error Disconnect power for 5 seconds condition and reconnect power If the condition persists please check the LCD display for additional information Contact Kodak service for assistance Also check the status monitor on your computer for a message Light is a flashing red The printer has detected an error Check the LCD display or status condition that needs your monitor on your computer for a attention message Flashing a rotating pattern of The printer has not detected that Please install a Printhead and red yellow and green a Printhead is installed ink cartridges User s Guide 5 Chapter 1 Photo Tray Status Light Light Status Action Solution Photo tray light is Off The photo tray is not engaged Push the photo tray in to e
50. py Preview feature can be used for photos or documents User s Guide 63 Chapter 5 Zoom and Crop To zoom and crop a photo before making a copy you must be in Preview mode see Turning Copy Preview On 1 With Preview set to Yes on the Copy menu press Start to enter Preview mode The photo on the glass is scanned and displayed with a crop box Use the Zoom and Zoom buttons to zoom iwand out Use the Menu button to select Brightness and adjust brightness 2 Press Zoom to enlarge the photo in 25X increments up to 5X magnification Pressing Zoom decreases magnification in 25X increments down to 1X 4 Press OK or Start to copy 64 Kodak EasyShare 5300 AiO Scan You can start a scan from the Kodak AiO Control Panel or your computer Scan with Control Panel Pressing Scan places the Kodak EasyShare AiO in Scan mode and displays the Scan menu on the screen Save Scan Settings When you change scan settings from the control panel the settings apply only to the current scan job To apply scan settings to all future scan jobs you can save your changes 1 Press Scan to display the Scan menu 2 Change the desired Scan settings 3 Press w until Save Settings is selected 4 Press d or to set save scan settings to Yes Scanning Photos With the Control Panel Scan menu you can scan photos to a file application or memory card Scan to File Place a photo or photos face down on the scanne
51. py Quality or Copy Settings Probable Cause 2 The brightness setting for copies is set too light Adjust the brightness setting to darker See Change Brightness or Copy Settings User s Guide 87 Chapter 8 Copies too Light or Dark The brightness setting for copies is set too light or dark Adjust the brightness setting for copies See Change Brightness or Copy Settings Copy Cut Off The original is larger than the paper loaded When the original is larger than the paper loaded use the Fit to Page option to reduce your original to the size of the paper loaded Scan Troubleshooting Scan Fails Probable Cause 1 Your computer is not turned ON Turn on your computer Probable Cause 2 Your EasyShare AiO is not connected to your computer Connect your EasyShare AiO to your computer with a standard USB cable Probable Cause 3 The EasyShare AiO Home Center software is not installed Insert the Kodak EasyShare 5000 All in One Printer installation CD and install the software Probable Cause 4 Your computer system resources may be low 1 Turn off your computer and EasyShare AiO and then turn them back on 2 If the problem still persists try scanning at a lower resolution 88 Kodak EasyShare 5300 AiO Support Scanned Image Blank Your original is not placed correctly on the scanner glass Place your original face down on the right front corner of the scanner glass Proofsheet Scan Unsuccessful Prob
52. r by jurisdiction Outside the United States and Canada In countries other than the United States and Canada the terms and conditions of this warranty may be different Unless a specific Kodak warranty is communicated to the purchaser in writing by a Kodak company no warranty or liability exists beyond any minimum requirements imposed by law even though defect damage or loss may be by negligence or other act EASTMAN KODAK COMPANY Rochester NY 14650 U S A Eastman Kodak Company 2006 MC MR TM Kodak Printed in China 78 Kodak EasyShare 5300 AiO Support Telephone Customer Support If you have questions concerning the operation of your EasyShare software Home Center software or EasyShare AiO you may speak with a customer support representative When you call please have the following information available Computer model operating system Processor type and speed MHz Amount of memory MB and free hard disk space Printer serial number Version of Kodak EasyShare software Version of Kodak Home Center software Print a Diagnostics Page Exact error message you received Your unit s Kodak Service Number under the printer access door KODAK SLEI HUMBER ROCAS User s Guide EN 79 Chapter 8 Customer Support Phone Numbers International Toll Fax International Toll Line JK JS aoa ta Visit www kodak com go dfiswwcontacts Troubleshooting AiO Fails to Power On The power supply
53. r glass Press Scan to display the Scan menu Press d or P to select Photo Press w until Scan To is selected a fF AQ N Press d or to select File 6 Press Start The photo is scanned and saved based on the Kodak AiO Home Center scan picture settings see Scan Picture Settings User s Guide 65 Chapter 6 Scan to Application The Home Center software enables you to maintain a list of scan destination applications Place a photo or photos face down on the scanner glass Press Scan to display the Scan menu Press d or P to select Photo Press w to select Scan To Press to select Application Press w to until Application is selected Press d or P to select another application O N O Oo A OQ N Press Start Scan to Memory Card 1 Insert a Memory Card into the appropriate card slot AN WARNING Never attempt to remove a memory card while it is being accessed Doing so can damage files on the card You can safely remove a card only when the status light next to the slots is not blinking Place a photo or photos face down on the scanner glass Press Scan to display the Scan menu Press d or P to select Photo Press w to select Scan To Press d or to select Memory Card NO oF Bb OQ ND Press Start Scanning Documents With the Control Panel Scan menu you can scan documents to a file application or memory card 66 Kodak EasyShare 5300 AiO Scan Scan to File 1 Load your original face do
54. re AiO to emit an audio feedback beep when you press a button on the Control Panel The default setting is to beep Press Menu to display the main menu Press w until Control Panel Settings is selected Press OK Press d or to enable or disable button sounds Press OK a FF Go N User s Guide 23 Chapter 2 Minutes to Standby When the Kodak EasyShare All in One is idle for the standby power setting timeout period it enters the Standby state The On Off indicator remains lit but power consumption is reduced When in the Standby state any activity such as a single button press or inserting camera card brings the EasyShare AiO out of the Standby state and returns it to the Ready state You can set the standby timeout from 10 30 minutes The default setting is 15 minutes a FF Go N Press Menu to display the main menu Press w until Control Panel Settings is selected Press d or to change the standby timeout period Press OK Date and Time Press OK The Power Settings menu is displayed with Minutes to Standby selected Your Kodak EasyShare All in One contains a clock for stamping the date and time on scans to a memory card O O N OO I FBP ND oa dk wk sk QO N 0 24 Press Menu to display the main menu Press w until Date and Time is selected Press OK to go to the Date and Time menu Press d or to set the Year Press OK Press d or D to set the Month Press OK Press d or P to set
55. rectly Color ink cartridge not installed Black ink cartridge not installed Ink cartridges not installed Printhead not installed Light is on Non Recoverable Error Media sensor failure Printhead failure Scanner failure User s Guide 7 Chapter 1 Card Slot Light Light Status Action Solution Light is off An SD MMC card is not inserted Remove and reinsert the or is improperly inserted in the SD MMC card card slot Light is on An SD MMC card is properly None inserted in the card slot Light blinks green Slow blink The internal card reader is initializing or communicating with the printer Fast blink There is a card or Remove the card and make sure communication error the card is not write protected or damaged Reinsert the card or replace with a new card if necessary LCD Display Screen The LCD screen displays photos messages instructions and menu parameters Menu navigation is accomplished with the 4 way Navigation buttons The screen is hinged at the back edge and can be positioned from flat on the control panel surface to vertical Instructions displayed on photos appear up to four seconds and then disappear or disappear immediately after you start interacting with the screen The instructions will return after fifteen seconds of inactivity When a second page of display text is present it is indicated by the down arrow w symbol positioned in the lower right corner of the menu area When
56. roduct or specified additional components or accessories elsewhere defined to be used with the installation of the product they must be used in order to ensure compliance with FCC regulation A CAUTION When using the wireless interface with an EasyShare AiO this equipment should be installed and operated with a minimum distance of 7 9 in 20 cm for 2 4 GHz operations between the radiator and your body This transmitter must not be collocated or operate in conjunction with any other antenna or transmitter FCC and Industry Canada This device complies with Industry Canada RSS 210 and FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Canadian DOC statement DOC Class B Compliance This Class B digital apparatus complies with Canadian ICES 003 Observation des normes Class B Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada Waste Electrical and Electronic Equipment labeling Y In the European Union this symbol indicates that when the last user wishes to discard this _ product it must be sent to appropriate facilities for recovery and recycling Contact your local Kodak representative or refer to www kodak com go recycle for additional information on the collection and recovery programs available for this product
57. rom the power outlet and the phone line from the modem WARNING The use of an accessory attachment that is not recommended by Kodak such as an AC adapter could cause fire electric shock or injury WARNING Pushing objects through the equipment openings can result in an electric shock or risk of fire gt gt bb gt PID DP Location CAUTION To prevent your EasyShare AiO from overheating do not block or cover the slots and openings in the equipment place it near a heat register or install it in a cabinet without proper ventilation gt 94 Kodak EasyShare 5300 AiO Appendix CAUTION Do not use your EasyShare AiO near water or spill liquid on it WARNING Do not place your EasyShare AiO on an unstable cart stand bracket or table Injury to persons and damage to the equipment may occur gt gt Environment CAUTION Excessive dust levels may damage internal parts CAUTION Unplug the equipment from the wall outlet before cleaning CAUTION Dropping your EasyShare AiO may damage the housing and result in extensive damage that will require repair by a qualified technician to restore normal operation WARNING Do not expose this product to liquid moisture or extreme temperatures KODAK AC adapters are intended for indoor use only The use of controls adjustments or procedures other than those specified herein may result in exposure to shock and or electrical or mechanical hazards A A For more
58. sheet into the EasyShare AiO IMPORTANT If the AiO printer goes into standby mode power is lost or you unplug the memory card camera or USB device before you scan the proofsheet the proofsheet session number becomes invalid and you will need to re print it 1 Insert a memory card into the appropriate slot a mass storage device into the USB port or connect a digital camera to the USB port The first photo is displayed AN WARNING Never attempt to remove a memory card while it is being accessed Doing so can damage files on the card You can safely remove a card only when the status light next to the slots is not blinking Load the main tray see Load Main Tray in Chapter 3 with letter size plain paper Press Menu Press w until Proofsheet is selected Press OK Press Start to print the proofsheet NO OF FP QD Complete the four steps on the proofsheet with the memory card storage device or camera connected Tagged Photos DPOF The Digital Print Order Format DPOF is an industry standard file that can be created by some digital cameras Camera selected photos are photos you tag for printing with your digital camera When you select photos with your camera the camera creates a DPOF file that identifies which photos have been tagged for printing Your Kodak EasyShare AiO can read the DPOF file from the memory card in a camera so you do not have to re select the photos to print NOTE Not all digital cameras allow you to ta
59. t However Bluetooth will work beyond this distance User friendly Name Your EasyShare AiO has a serial number that is used to construct name for Bluetooth printing The default name is Kodak5300 XXXX where XXXX represents the last four digits if the AiO printer s serial number You can change this to a more user friendly name with the AiO Home Center See General Settings in Chapter 2 Printing When a Bluetooth connection is made no other functions are available and the LCD display indicates printing from Bluetooth You control printing from your Bluetooth device User s Guide EN 37 Chapter 4 Panoramic photos Panoramic images are detected based on the aspect ratio of the image A panoramic image is displayed in a fit to page manner with blank space above and below the image The crop box is adjusted for a 300 x 100 mm 12 x 4 aspect ratio and initially encompasses the entire image If panoramic images are selected for printing the AiO printer prints all of the panoramic images after all other images have printed Before printing the panoramic images the EasyShare AiO displays a message to allow you to insert panoramic paper then press Start again to print the panoramic images Layouts The photo layouts on your Kodak EasyShare AiO snap to the nearest standard print size whenever possible based on the combination of layout and paper size loaded Otherwise the layouts are based ona standard 2x3 aspect ratio The tabl
60. tected Access 100 Kodak EasyShare 5300 AiO Index 2 2 Sided Printing Ass Na 16 A PPT 49 Audio TEEN 23 B Soa ee Os NEON 50 Bluetoot Mercie 37 81 Borderless vu 87 BHE DUNE EE ton 63 C Cala e RE 73 GE ER 74 GE EE PO TO NE EE EE 70 HN PP P PAE PE P E ETS 51 Bello tee gei EE 82 COMPU 82 91 PE 2 34 Go og EE ee 62 63 Copy PD 87 88 Cropped bichures 85 C stomer SUN arnet 79 D BE Ga de RE O 86 DE 23 24 DIdenostia gt EE 70 PROF 22 36 Be A ate 16 E en veera 31 F Frmvere DSC ea ba 71 A 59 ROLM batangan ana nona 10 l A 35 A eee tae eer ere tree Ae 15 71 81 eos 71 J JAM 83 L Bet EE 32 User s Guide len ee EN NE 25 Bo EN ENE EEE 40 LEI 8 Letter Pape ncaa ashes cuca iia 45 A eera E TOEO TATTA 86 M MAT 28 E ag Eu 69 TEN 70 Memory card slots ooooooooooo 9 ua Bb 18 O Ge EE ENE EE 27 P Klee ln Ce ui 38 Kier ER PN 84 92 PaO el Ce EET 81 82 FINN 83 PRoto Layout en 41 42 43 44 A onani Ban 61 PAROLO Pinata 85 A N S OA 30 PNO LOS perro 53 Ste d Et std 9 34 85 FO 13 80 GENE sonnet NN AT 52 63 Plass 34 36 40 51 Pn RE e ER Kette e 85 Print Problem ri tater nana nae 84 85 A e 85 EI POr 86 Printhead A fel 74 den ot 13 74 Primung Problem Saath 84 Pn NN 86 POOLNE maa eee 36 89 Q UUS 51 62 QUV dea ntt ab as 51 62 101 Index R NEQUIEEMENTS ra 91 EE 25 S SL NA AN EET ROR AN AAN AN 94 SEUNG EEE 58 Sampe Patel ge 21 Scale EE 60 Se EE SEN NE EEE ETE
61. the fastest copy speed but the lowest quality 1 Onthe Copy menu press w until Quality is selected 2 Press d or to change the copy quality 3 Press OK to set and continue setting options or Start to copy 62 Kodak EasyShare 5300 AiO Copy Change Brightness You can change the brightness of copies with 3 being the darkest and 3 the lightest If the Copy menu is not displayed press Copy Press w until Brightness is selected Press to darken or to lighten RR Q N Press OK to set and continue setting options or Start to copy Set Preview Copy Preview allows you to preview your originals before making copies The Copy Preview screen shows the scanned image that you can zoom or crop see Zoom and Crop 1 Onthe Copy menu press w until Preview is selected 2 Press d or to enable or disable Preview 3 Press OK to set and continue setting options or Start to copy Save Copy Settings When you change copy settings from the control panel the settings apply only to the current copy job To apply copy settings to all future copy jobs you can save the setting changes 1 Ifthe Copy menu is not displayed press Copy 2 Press w until Save Settings is selected 3 Press Yor to set save copy settings to Yes Previewing Copies Previewing Copies Copy Preview mode is entered when the following conditions exist m The EasyShare AiO is in Copy mode E Preview is set to Yes m The Start button is pressed The Co
62. the ink cartridges onto the paper Printer maintenance involves E Calibration E Clean the printhead Calibration The Kodak EasyShare AiO performs a calibration every time you install or replace a printhead However you can run a calibration if you are seeing changes in the image quality Calibration aligns the printheads and performs a nozzle health check to enable high quality prints To calibrate from computer 1 Load the main tray or photo tray with photo paper IMPORTANT If you don t have any photo paper you can use plain paper but photo paper is highly recommended for calibrations Start the AiO Home Center Click to open the Help panel Under General Links click Maintenance Click Calibration to make a calibration print oo BOO N Follow the instructions on the calibration print to calibrate the printer User s Guide 73 Chapter 7 To calibrate from control panel 1 ao Pb OQ N Load the main tray or photo tray with photo paper IMPORTANT If you don t have any photo paper you can use plain paper but photo paper is highly recommended for calibrations Press Menu Press w until Calibrate Printer is selected Press OK A new screen appears with Print Calibration Page selected Press Start and follow the instructions on the LCD screen to complete the calibration Clean Printhead If you notice a degradation in the quality of prints the printhead may need cleaning To clean printhead from computer
63. the second or subsequent page of text is in view the presence of a previous page is indicated by the up arrow S symbol in the top of right corner of the menu area Each time you press Navigate Down el you advance the highlight down 1 row When the last row is highlighted pressing w causes page 1 to be replaced with page 2 When page 2 appears the highlight is on the top row The up arrow symbol appears at the right edge If a third page of menu parameters is available the down arrow w symbol appears in the lower right corner Until the highlight is advanced pressing Navigate Up returns you to the previous page Holding down any of the 4 way Navigation buttons causes them to repeat scroll 8 Kodak EasyShare 5300 AiO Product Overview Default Display Settings Default settings are provided for each option If you make changes to the settings the changes remain as long as you do not change modes You can save the settings in each mode by navigating to Save Settings and pressing OK You may reset options to the master defaults by going to the main menu and selecting Reset All Settings Photos The LCD screen displays JPG images when you insert a memory card camera or USB device However the following images will not be displayed File size greater than 8 MB Image size greater than 12 megapixels Image colorspace is not SRGB or adobeRGB Progressive JPEG images Memory Card Slots and USB Port Your Kodak EasyShare All
64. tridge immediately to prevent any drying of the ink 2 Remove and discard the orange cap IMPORTANT Handle ink cartridge carefully to avoid ink transfer User s Guide EN 15 Chapter 2 4 Press down on the ink cartridge until you hear it snap into position d Le al O Remove and discard the orange cap 7 Insert the color ink cartridge into the printhead 9 Close the printer access door NOTE For the best quality prints store ink cartridges in a location where the temperature does not exceed 85 F 30 C Install the Duplexer The Kodak EasyShare AiO supports an optional duplexer Kodak EasyShare 5000 Series Two Sided Printing Accessory that enables printing on both sides of the paper When installed the duplexer is automatically detected by the printer and computer system software The duplexer is limited to plain paper The paper dimensions that can be used are from 6 9 to 8 5 inches 17 5 to 21 6 cm wide and from 9 8 to 11 7 inches 24 9 to 29 7 cm long You can purchase a duplexer and other accessories for your printer at www kodak com go accessories 16 Kodak EasyShare 5300 AiO Getting Started 1 Remove the door on the back of the printer by pressing in on the two latches and pulling out You can control how long the printer waits before a sheet is flipped by the duplexer with the AiO Home Center See General Settings Startup When you power on your Kodak EasyShare
65. ts Requirement minimum Recommended User s Guide 91 Chapter 9 Paper Types The following tables show the paper types and sizes the Kodak EasyShare AiO supports for copying and printing Supported Paper Types Plain paper ee sai 64 to 90 gsm 110 Ib index max Card Stock 200 gsm SETER 20 to 24 Ib H 75 to 90 gsm Transparency All commercially available inkjet varieties with or without a widestripe Labels All commercially available inkjet varieties on 8 5 x 11 and A4 size sheets lron on Transfer All commercially available inkjet varieties on 8 5 x 11 and A4 size sheets 92 Kodak EasyShare 5300 AiO Appendix Supported Paper Sizes Usage Se ry A4 210x297 mm A5 148x210 mm Document page sizes GE Ee os rene US Executive 7 25x10 5 in 184x266 mm Main US Legal 8 5x14 in 216x356 mm US Letter 8 5x11 in 216x280 mm Custom sizes 3x5 in index cards 76 2x127 mm Index Card Stock 4x6 in index cards 101x152 mm Main 5x7 in index cards 127x178 mm Transparency A4 210x297 mm Main lron on Transfers US Letter 8 5x11 in 216x280 mm B5 6 92x9 84 in 176x250 mm C5 6 38x9 in 162x299 mm C6 4 49x6 38 in 114x162 mm Eelere A2 4 37x5 75 in 111x146 mm Main DL designated long 4 33x8 66 in 110x220 mm US 7 7x9 in 178x127 mm US 9 9x12 in 127x305 mm US 10 4 12x9 5 in 105x241 mm 3 5x5 in 89x127 mm 100x150 mm 4x6 in 101x152 mm 4x8 in 10
66. unit No Paper Feed Paper does not feed You may have a message on the display on the printer and or in the Status Monitor on your computer IMPORTANT For best result use only Kodak Ink cartridges and paper for your printer The paper tray s may be empty Load paper into the paper tray s then press Start 82 Kodak EasyShare 5300 AiO Support Check the paper 1 2 3 4 5 Disengage the Photo tray Inspect the paper and make sure paper no sheets are damaged in any way Reload with new paper if necessary Carefully fan the paper to keep the sheets from sticking together Reload the paper tray s Do not overfill Engage the Photo tray if printing 4 x 6 Photo s then press Start to resume printing Paper Jam The paper did not advance or was not picked properly from the paper tray 1 2 3 4 5 6 Open the paper trays and remove the paper supply Press in the latches on the rear access door and remove it Pull the paper out from the rollers without tearing it IMPORTANT If the paper tears while removing it check inside the AiO for torn pieces of paper and remove them More jams are likely to occur if all the torn pieces are not removed Replace the rear access door by pressing it in until it latches into place Reload the paper tray s Do not overfill Re engage the Photo tray if desired Printer not Responding If you receive a Printer not Responding message 1 Turnthe printer off an
67. ured with a weighting filter dBm A measured power level in decibels relative to 1mW Dongle A small electronic device that plugs into a USB port DPOF Digital Print Order File An ASCII order file that you can generated in a camera that supports DPOF DPOF files enable you to request simple reprints of the photos in the file E EAP Extensible Authentication Protocol EXIF EXIF stands for Exchangeable Image File Format and is a standard for storing interchange information in image files especially those using JPEG compression Most digital cameras now use the EXIF format J JPEG The term stands for Joint Photographic Experts Group because that is the name of the committee that developed the format JPEG is a compressed image file format JPEG is a lossy format which means some quality is lost when the image is compressed K KPT Kodak Perfect Touch P PictBridge A Camera and Imaging Products Association standard that enables direct printing between any PictBridge compliant digital cameras and any PictBridge compliant printer Picture Transfer Protocol PTP A standard for transferring pictures from a digital camera PPP Point to Point Protocol PTP Picture Transfer Protocal A standard for transferring pictures from a digital camera T TKIP Temporal Key Integrity Protocol User s Guide J9 Glossary WEP Wired Equivalent Privacy Wi Fi Wireless Fidelity WLAN Wi Fi Local Area Network WPA Wi Fi Pro
68. with the last page and end with the first page NOTE There can be a delay when printing a large document while it is being spooled Printing will begin when the last page is spooled Collate You can collate pages when printing multiple copies Scale Layout You can scale pages or pictures by percentage or page size Multi page Layout The driver can reduce multiple pages so that they can all be printed on one sheet of paper Poster Layout This function enlarges a picture divides it into several pages and prints each page on a separate sheet of paper You can paste these sheets of paper together to create a poster Booklet Layout The pages are distributed and printed on both sides of the paper and arranged is sequence When they are folded in the middle and stapled they create a booklet Print Mirror Image Flips the image for iron on printing User s Guide 33 Chapter 4 Two sided Printing You can print on both sides of the paper Watermark You can select or create a background watermark Print Photos from a Camera 1 Connect your camera to the EasyShare AiO The PictBridge logo is displayed on the LCD PictBridge Connection OH 2 Load the photo tray with photo paper See Load Photo Tray in Chapter 3 3 Use your camera to select and print photos Print Photos from the Control Panel The Photo Print mode is initiated by pressing the Photo button inserting a memory card or connecting a USB device to the Kodak Eas
69. wn on the right front corner of the scanner glass 2 Press Scan to display the Scan menu 3 Press d or to select Document 4 Press Start The document is scanned and saved based on the Kodak AiO Home Center scan document settings see Scan Document Settings Scan to Application 1 Load your original face down on the right front corner of the scanner glass Press Scan to display the Scan menu Press d or to select Document Press w to select Scan To Press d or P to select Application Press w to until Application is selected Press d or to select another application O N O oO A Q N Press Start User s Guide EN 67 Chapter 6 Scan to Memory Card 1 Insert a Memory Card into the appropriate card slot AN WARNING Never attempt to remove a memory card while it is being accessed Doing so can damage files on the card You can safely remove a card only when the status light next to the slots is not blinking 2 Load your original face down on the right front corner of the scanner glass Press Scan to display the Scan menu Press or to select Document Press w to select Scan To Press or to select Memory Card N OO Om fF OW Press Start 68 Kodak EasyShare 5300 AiO Maintenance The Kodak EasyShare All in One requires little maintenance However you should clean the glass and lid backing to remove dust and fingerprints Fingerprints and other debris on the glass or lid bac
70. yShare All in One 1 Insert amemory card into the appropriate slot a mass storage device into the USB port or connect a digital camera to the USB port The last photo is displayed WARNING Never attempt to remove a memory card while it is being accessed Doing so can damage files on the card You can safely remove a card only when the status light next to the slots is not blinking 2 Load the main tray see Load Main Tray in Chapter 3 or photo tray See Load Photo Tray in Chapter 3 with photo paper NOTE The Photo Tray only supports 4x6 inch and 100x150 mm photo paper Press to select the number of prints for this photo Press to preview the next photo TIP To select all the photos on a memory card or mass storage device hold down the OK button for 2 seconds Holding down the OK button again for 2 seconds will de select all the photos Repeat Steps 3 and 4 until you are finished selecting photos Press Start to print the selected photos or Photo to set print options Set print options See Set Print Layout See Set Number of Prints See Set Color See Set Print Quality After a photo is printed it is de selected 34 Kodak EasyShare 5300 AiO Print Index Print The purpose of an index print is to catalog contents of a memory card or USB flash drive An Index print contains the following Sequence numbers for the relative position of each photo within the defined set of photos incrementing from 001 and continuing

Table Of Contents

Contents

Download Pdf Manuals

Related Search

Related Contents