Wine Cabinet WINCAVE User Manual
Contents
1. adjustable by using the external display You can select between 10 C and 16 C HOW TO ADJUST THE TEMPERATURE RANGE AMPHORA MODEL When the cabinet is first plugged in the temperature is pre set at a fixed 14 C The display indicates for 3 seconds the set temperature Then it displays the current internal temperature Pressing on the lt plus gt or lt minus gt keys will display the set temperature level After releasing the keys the current interior temperature is displayed again Pressing the lt plus gt or lt minus gt keys at the same time for 3 seconds will enable you to reach the programming mode For the first 3 seconds the display shows a flashing P After 3 seconds the display shows the set temperature flashing You can adjust the value by pressing the lt plus gt or lt minus gt keys After 3 seconds without pressing any key the temperature is automatically registered and the current interior temperature is shown again In case of power failure the set temperature is stored in the programme s memory and will be used as soon as power is re established _4 Internal equipement LOCK Your cabinet is equipped with a security lock To open it it is necessary to push the key in order to disengage the security and to be able to rotate the key to the right or the left SLIDING AND STORAGE SHELVES WINCAVE offers 2 options to store your wine bottles A storage shelf for 48 bottles maximum Ref C S2. the set temperature Amphora Switch off and then the interior T is gt 16 C on again If the compressor does not work switch off and contact your after sales service The ambient T C is lt 10 C and the Check the set temperature Amphora Switch off and then interior T C is lt 10 C on again If the heater does not work switch off the cabinet and contact your after sales service The interior T is lt 10 C and the Check the set temperature Amphora Switch off and then compressor works continuously on again If the compressor does not stop working switch off and contact your after sales service There is frost on the inside back This is a normal physical phenomenon which will appear wall after opening the door A lot of ice has collected on the Check that the door is well closed back wall Check the set temperature Amphora If the interior temperature is the correct one check that the bottles are not touching the rear of the cabinet on fixed shelves If the temperature is lower that the set temperature be sure that the compressor is not working all the time see above Cabinet is working but T is notas Check that the plug used is not dependant on a selected commutator Shelves do not slide correctly Check that the shelf rail is properly adjusted The fixed shelves are not straight The wood is very dry and needs the natural humidity of the cabinet to return to it s original straight form Wate
3. 4s su A sliding shelf for a layer of 12 bottles Ref C coul su Adjustments the male screws fitted under the sliding shelf allow you to adjust the shelf width to avoid it moving out of the supports positioned on the walls Ref C coul su This shelf allows you to store your bottles with their labels facing upwards When you slide the shelf towards you you can identify them without moving them A wooden label carrier helps identification Each shelf is positioned on 4 metal supports which fit into the side of the cabinet You can therefore progressively add more sliding shelves to your cabinet Installation of shelve Insert the rear pin into the stamped hole on the cabinet wall Installation of the metal TA supports for the storage AE shelves Insert the font pin into the stamped hole on the cabinet wall and push it down Front CAPACITY OF YOUR CABINET MEASURED IN BORDEAUX BOTTLES Your model Possible capacity CV 162 Btles CV 150 Btles 138 Btles 126 Btles Your cabinet is equipped with the following accessories Sliding shelves C coul su 12 bordeaux s bottles maxi 000000 Fixes Shelves CS 4s su 48 bordeaux s bottles maxi QOD CX Your model Possible capacity CV 246 Btlles CV 210 Btles 222 Btles 198 Btles 186 Btles Control and maintenance THE lt LED SECURITY gt TEMPERATURE ALARM 3 colour LED indication If temperature is more than 4 C lower than set temperatur
4. a ee Wine Cabinet WINCAVE User Manual INDEX OPERATING INSTRUCTIONS 2 INSTALLATION 2 CABINET DESCRIPTION 2 Technical specifications CONNECTION AND TEMPERATURE SETTINGS 3 Your temperature Smart Handle MONO T Smart Handle AMPHORA How to adjust your temperature EQUIPMENT 4 5 Storage and sliding shelves Installation of shelves Capacity of each cabinet CONTROL AND MAINTENANCE 6 Temperature Alarm the lt led security plus gt Carbon Filter Cleaning your Wincave cabinet PROBLEM SOLVING 7 INSTALLATION OF THE SMART HANDLE 8 TEST 25 Rue DELAMBRE 75014 PARIS Tel Fax 01 42 79 83 34 WWwW wincave com contact wincave com Operating Conditions Before installing your cabinet read these instructions carefully OPERATING CONDITIONS The WINCAVE cabinet you recently purchased is a maturation cabinet It is therefore fitted with both cold and warm circuits The ideal temperature is 12 C 14 C When the temperature inside the cabinet is above the set temperature the COLD circuit is activated When it falls below the set temperature the WARM circuit automatically starts heating up You therefore obtain the programmed temperature THE AMBIENT TEMPERATURE RANGE IS FROM 5 to 35 C INSTALLATION The WINCAVE cabinet should not be positioned next to a significant warm source or in a very humid environment Make sure that your cabinet is properly levelled A surrounding air circulation 1s recommended to optimise effi
5. ciency You need to adjust the front feet to ensure that your cabinet 1s properly levelled The nominal power should be 220V 50Hv voltage between 198 242V You need to have an efficient earth 15 amp CABINET DESCRIPTION 1 Internal and external cabinet walls of steel Walls are 60 mm thick insulated with polyurethane foam v Sensor Magnetic door joint Shelves sliding and storage Transportation wheels rear and adjustable feet front Rust proof security lock Heater automatic winter function Upper and lower aeration oe a 53s Connecting and temperature setting WARNING YOU MUST WAIT 48 hours after unpacking and positioning your cabinet before switching on After plugging in load your cabinet step by step THE BOTTLES MUST NOT BE IN CONTACT WITH THE BACK OF THE CABINET to maintain air circulation around the bottles YOUR CELLAR TEMPERATURE Depending on your WINCAVE model your cabinet is fitted with the smart handle equipped with one of the following two electronic regulations French patent no 9106156 Wood Handle Sticker Cover for PCB box Aluminium carter PCB Regulato r PCB box Smart Handle Mono T with the lt LED security gt The ideal temperature for wine storage is between 12 C and 14 C The temperature is pre set and needs no adjustment YOU HAVE NOTHING TO DO Smart Handle Amphora with display and the lt LED security gt The temperature is
6. e Blue LED If temperature is no more than 4 C higher or lower than set temperature Green LED If temperature is more than 4 C higher than set temperature Red LED WARNING A certain time is necessary to obtain the required temperature after plugging in the cabinet or after opening the door CARBON FILTER An active carbon filter is located in the upper part of your cabinet This filter allows a good air circulation and prevents external odours to penetrate into your cabinet You need to replace this filter every year sometimes twice a year if your room is very humid CLEANING YOUR WINCAVE Twice a year clean the condenser metallic grating at the back of the cabinet The wooden parts the top and bottom of the door and the general parts of the cabinet must be cleaned with a soft cloth and water Never use chemical or solvent produce or abrasive cleaning materials IMPORTANT NOTE Wood handles are made of solid oak The handle is hand made polished and lacquered by craftsmen Each handle is therefore unique and never exactly the same as another Malfunctionning Your problem and its answer are perhaps in the following list There is a vibration when the Cabinet is not level on the floor Use the adjustable feet at compressor is working the front of the cabinet No indication after plugging in Check plug fuse and socket Amphora your after sales service after sale service The ambient T is gt 16 C and or Check
7. r is dripping from the front of The cabinet is not correctly positioned on the floor Use the the cabinet adjustable feet to create a very slight slope to the rear Check that there is nothing obstructing the evacuation hole on the compressor step Description of parts oo 1 Control panel stand TA 2 Screw for fixing the control panel pre screwed on the ag 3 Screws for fixing on the smart handle 1 Smart handle MONO T or AMPHORA Neccessary tools 1 Phillips screwdriver Description of the smart handle A Wood handle B Plastic cover C Electrical unit D Housing for electrical unit 4 E Temperature regulator F Cover for electrical unit G Control panel stand H Reception hole for the electrical unit I Channel for door and handle I a Porte N N N ae N SS L DRE INSTALATION aA AS 1 Screwing the electrical unit bracket on the door 1 2 Extract the electrical connectors from lt A the door and from the handle A eo _G 3 Place the electrical unit on it s stand 4 Connect together the electrical connections a LICK i e T 7 a Tee 5 Introduce the electrical connection into the tn door channel and join the two parts together 5 6 Using the 3 screws fit the door handle
Download Pdf Manuals
Related Search