Reliable F3 Instructions
Contents
1. NA lt RELIABLE AN PANT PRESS USER MANUAL Model F3 IMPORTANT SAFEGUARDS When using an electric appliance basic precautions should always be followed including the following WARNING DANGER OF SCALDING Read all instructions before using this pant press to reduce the risk of fire electric shock or injury This product is designed for domestic use only ES ES Do not use outdoors Do not leave your pants press unattended while switched on Turn off the switch and unplug the electrical cord when not in use To unplug grasp the plug not the cord Do not allow the pants press to be used as a toy Close attention is necessary when used near children pets or plants The appliance is not intended for use by any children or infirm persons without supervision Children should be supervised to ensure that they do not play with the appliance Do not immerse the pant press into water or other liquids Do not use with damaged cord or plug If unit is not working as it should has been dropped damaged left outdoors or immersed into liquid contact a licensed service technician for assistance Do not pull or carry by cord use cord as a handle close a door on the cord or pull cord around sharp edges or coners Keep cord away from heated surfaces Do not use extension cords or outlets with inadequate current carrying capacity Do not handle or use this unit while hands are wet Use only a2. iling the most common problems their causes and solutions Prior to troubleshooting isolate the unit by removing the cord from the power socket PROBLEM CAUSE SOLUTION Plug into electric socket and make sure the power Indicator light is on please contact a licensed technician Unit is not plugged in Unit fails to operate properly Unit is damaged or malfunctioning Unit is not plugged in Plug into electric socket Unit fails to heat up The press board has Immediately stop use been damaged or is and let the unit cool malfunctioning down completely Contact a licensed technician www reliablecorporation com
3. ld the front pressing plate in the open position B How to insert the pants 1 Place the cuffs or bottom legs of the trousers as far down as possible between the front pressing plate and the press board The waistline of the pants should be hung over top edge of the front pressing plate Tidy up the slack of pants Make sure to place the pants in the middle of the front pressing plate with the side seam as indicated in Figure 3 aligned with the groove in the padding figure not shown in the front pressing plate C To close the front pressing plate 1 Pull the press board bar to the 2 step 1 step is for thick trousers or pants 2 Hold the waistline of the pants and gently pull upwards This will smooth out any wrinkles and ensure that the trousers are lying flat between the front pressing plate and press board 3 Pull the press board bar down firmly until the front pressing plate is fully locked into the closed position Pull the pants upwards once again D Plug the cord into the power socket The power indicator light will illuminate and the press will start automatically E The press will automatically shut off when the job is completed and the power indicator light will also goes off To restart the pressing press the on button the power indicator light will illuminate again and start the pressing cycle TROUBLESHOOTING GUIDE Below is a chart deta
4. s described in this manual Operating unit in any way other than recommended may result in damage to unit or injury to operator Do not disassemble unit or attempt to make any repairs yourself Incorrect assembly or repair could result in a risk of fire electric shock or injury to persons when operating Store your pant press in a cool dry place Allow unit to cool completely and loop power cord loosely around unit before storing SAVE THESE INSTRUCTIONS F3 pant press product information A Control panel B Storage for personal items cuff link keys ect C Safety chain D Press board bar E Press board F Front pressing plate G Foot H Cord wrap I Cord J Plug K Support L Fabric button M Power Start button N Indication Light O Coat hanger P Hanger support A 7 RELIABLE ASSEMBL Y INSTRUCTIONS Accessories e e gt Screw Hanger support A Attach the support to the feet B Insert the attached screws into each hole in the feet and tighten them securely with a screwdriver C Turn chrome supports 90 so that when you view the hanger from the back they point away D Push the hanger with supports into the back of the panel as illustrated Note this will require firm pressure Operating Instructions A To open the front pressing plate Slowly pull the press board bar to open the front pressing plate The press board bar will ho
Download Pdf Manuals
Related Search