ScanSpeed 1236R/1248R User`s Manual
Contents
1. 5 5 Transportation of the instrument __ 4 _________ 6 ei rre MM 6 1 Check list 6 2 Tiouble SONIC Soc u u uuu uuu RR UNS www labogene com 5 Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 1 Meanings of Symbols amp Safety Precautions 1 1 Meanings of Symbols 1 1 1 Symbols on the device Symbol Meaning Symbol Meaning Attention and warning k Attention and warning for an electric shock Attention and warning Fea see Attention and warning emm 2288042088 p SPA be for the door opening J i be gel ths reel T la for the rotor coupling Please lis the rater im an place and closing Attention and warning Attention and warning for correct way of E for correct way of sample balancing in the I buckets position rotor Indicate a hole for door opening in case of emergency 1 1 2 Symbols in this document Symbol Meaning Symbol Meaning 6 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R This symbol refers to safety Note A relevant warnings and indicates This symbol refers to the important possible dangerous outcomes reminder 1 2 Safety Precautions Before using the instrument please read this operation manu2. gt Check the proper power 2 Turn on the instrument by pressing a switch on the right side of the instrument gt With beeping sound right before setting value is displayed gt The default values are Max rom 10 min ACC 4 DEC 4 and 25 3 2 2 Door Release Action 1 For opening the door touch the DOOR button gt Should touch the DOOR button when the door is closed Door LED shows off gt Close the door until hearing clank shut gt When the door is opened the door LED turns on The door is not opened while the instrument is running If the door is opened the instrument is not running even with pressing the Start button For operational safety this instrument has the automatic rotor recognition function When you supply the power Searching Rotor Change to Rotor ID will be appeared If the rotor is absent the Error 9 will be appeared This message will be disappeared after rotor coupling 12 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R Power Failure If there is any power failure during operation door is not opened with Door button Door can be opened only when the operation is completely stopped and the power is on again If you want to open the door at the power failure please refer 4 9 Emergency Door Open v The door is not automatically opened after finishing operation to keep the sample at proper
3. gt It is for quick and short spin down Action Qm m l FE w Fi 1 If you touch Pulse button and release at the point you want to stop after displaying recognition OK the centrifuge decelerates immediately gt If you touch Pulse button less than 1 seconds the instrument is stopped after reaching the set RPM or RCF 4 8 Start Stop Action D After setting RPM RCF Time and Temp touch Start Stop button gt During running Start LED is turned on gt The instrument is running only when the door is closed Action 1 In case of touching the Start Stop button the operation is stopped running g E G m EE 24 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 9 Emergency Door Open For emergency door open you can use the emergency door open tool as long as the instrument is completely stopped The door can be unlocked manually with 5 mm T wrench through the emergency opening hole 1 Find the emergency hole in the front body of the instrument and take out the white rubber closure 2 Insert the emergency open tool into the hole and push it until the door is released Manual opening should be performed only when spinning is completely stopped Otherwise harmful damage will be accompanied to not only operators but samples After opening the door manually it is recommended to wait until
4. should follow national regulations Do not place dangerous materials within 30cm distance around the instrument and that is also recommended by IEC 61010 2 020 Use the emergency door open function only when the door button on the control panel is dumb under the condition of complete stop of rotor running Never try to open or move the instrument if it is not completely stopped If the power input is more than 10 of the recommended voltage or fluctuates frequently it may affect some functions of the instrument and often result serious damage 8 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 2 Product Description amp Technical Specifications 2 1 Product Description 4 Power Socket T Power Socket Chamber aum l Control gt Emergency Door Panel Open Hole e Power Switch d pee Rotor Locking Tool Emergency Door User manual Power Cable Open Tool U i a E Es r aem Lubricant grease Inclinometer 1236R Spanner 1236R 9 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 2 2 Technical Specifications Fixed angle 12 000 rpm 16 582 xg Max RPM RCF Fixed angle 6 x 85 ml Max capacity Temp range C 20 40 FAST COOL button Yes or continuous 473 600 x 840 12368 655 x 620 x 357 1248R 1100256
5. temperature 3 3 Rotor coupling and disassembling Action 1 Before coupling a rotor clean the motor shaft and chamber with soft dry towel Swing Out Rotor 2 Mount the proper rotor into the motor shaft 3 Grasp the rotor with one hand and place rotor locking tool L _ at the center hole of rotor To assemble the rotor Rotate the T tool clockwise until tightly assembled To disassemble the rotor Rotate the T tool counterclockwise 4 Hang the appropriate buckets into the rotor gt Load the identical bucket at each wing for safety Remove dirt and water drop at the link area between the rotor and bucket for cleanness 5 Spin the rotor manually to check the buckets swing with same angle freely If 13 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R they do not swing freely apply the Lubricant grease to the link area Fixed Angle Rotor 2 Mount the proper rotor into the motor shaft Grasp the rotor with one hand and place rotor coupling device T tool at the center hole of rotor gt assemble the rotor Rotate the T tool clockwise until tightly assembled gt disassemble the rotor Rotate T tool counterclockwise 3 close of the rotor lid rotate the rotor lid nut clockwise gt For closing lid rotate the rotor lid nut clockwise gt For opening lid rotate the rotor lid nut counterclockwise When you
6. 7 Product Description and Technical Specifications esa csactaneesscesssuasiacashsceascesstiestacdssathessneeenconsdes 9 POC HOTO EP 9 10 11 Balance Adjustment Only TOL 1230B ee mtr AGRA 11 Power On off and Door HERE memet EU terree ta MAMANS 12 Rotor 13 Balance Adjustment Final Only for 15 Positioning or sample TUDES uuu 16 17 Key F nctons Of Control Panel LLULLA i ii l i l i ii D 17 Settimo d 18 SEU HEB u _________6_____ 19 Setting Temperature and Fast Cool eerte aaa CU ace 20 Acceleration Deceleralloluyu ui M ery ore 21 Piograimsevitig 22 Fil u 23 EIEE S wu cc O 23 Blo Oe PH 24 ill 25 Su 25 REN 25 4 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 5 3 UO 5 4 a
7. Action A E n v Time is down counted after starting centrifugation 1 Touch the TIME button once gt HOUR is appeared on the display window 2 Touch the A V buttons to change input hour value eu gt If you do not touch the AW button for 5 second the X setting mode is cleared 3 Touch the Enter button to pass the MIN value setting 4 Touch the AW buttons to change input minute value 4 B 5 gt After keeping holding finger the A W buttons for 5 seconds the unit of setting value is changed to 10min from Eri x I Imin gt If you do not touch the A W button for 5 second the setting mode is cleared 5 Touch the Enter button to complete the setting 19 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 4 Setting Temperature and Fast Cool 4 4 1 Setting Temperature gt Temperature can be set from 20 C 40 C gt Temp setting unit 1 C Action ITEM 1 Touch the TEMP button gt Temperature value blinks in display 2 Touch the AW buttons to change input value gt If you do not touch the AW button for 5 second the setting mode is cleared 3 Touch the Enter button to complete setting 4 4 2 Fast Cool 1 1 Setting the temperature Please refer to 4 4 1 Setting D a A Temperature v amp eur Eater 2 Touch the Fast C
8. Balancing 00 10000 heck the q force of sample containers 70 805 filling for safety f the number of samples is not pair please load the control tubes at each symmetrical position Otherwise it results noise and vibration which eventually damages the instrument Ke For safety the Imbalance Cut Off function will be occurred if there is imbalance of loading tubes Error 8 Imbalance error Please refer to 6 Trouble Shooting 16 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 Operation 4 1 Key Functions of Control Panel RPM RCF TIME Temp ACC DEC PROG Enter Fast Cool Pulse Start Stop Door RPM ace DEC For automatic conversion of RPM RCF and to set the speed To set time available range up to 9 hour 59 min 59 sec 0 00 00 continuous To set temperature To set the acceleration amp deceleration level from 1 to 5 steps 0 step means natural deceleration and speed is faster for bigger numbers of steps To save a set of setting values or call the saved setting value For completion of data setting To reach rapid refrigeration up to the setting temperature For quick runs Commend start and stop operation For opening instrument lid 17 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 2 Setting RPM RCF Action
9. when power blackout or seddun stoppage occurs W The Aerosol tight buckets and rotors pereat contamination and eesarts safely Autoclavable ind corrosion resistant rotors ensure safety and lang life E High quality cabinets with scratch resistant powder coated finished 2 CONVENIENCE IN OPERATION B Easy to need LEO disslay with bright white lettering pn a blue LED background B Tine contral of pelse aed coatinusus m m cm mm m m w WW Automatic RPHV RLF conversien for prompt detection of gforce Easy to check sctual rpm throsgh the top window nf dear Y 2 E program memory For up to 100 programs Automatic rator ideetification function W A large assortment of rotors fixed angle or with buckets end adaptors EASY CUSTOMIZATION rotors sample containers and adaptors can be manufactured accarding customers specification Flexibility of including any additional l unctipes er i need ECO FRIENDLY MANUFACTURING B Dust free AC induction motor E Eco safe refrigerant 404 B Very quiet operation at lesser than 56 dB 1 1 1 2 2 1 2 2 3 1 3 2 3 3 3 4 375 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 1 5 2 CONTENTS Page Meanings of Symbols amp Safety Precautions 6 Means or STM 6 A EE OON S
10. 8 78 248 10 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 3 Installation 3 1 Balance Adjustment Only for 1236R Imbalancing of the instrument itself causes vibration noise and error during operating Check the level of the floor surface with an Inclinometer before installation Action After locating the instrument on the solid and flat floor check the horizontality with an Inclinometer 1 Place the Inclinometer on top of the instrument gt Try to locate all bubbles in the center of Inclinometer with rotating the red gear which is in caster of the instrument 2 Adjust the height of four wheel which is at the bottom of the instrument with rotating the red gear which is in caster of the instrument for the first balance adjustment For the final balance adjustment please refer to 3 4 gt For tighten a wheel rotate the red gear counterclockwise with a spanner gt For extending a wheel rotate the red gear clockwise with a spanner Place the 1248R on the solid flat table Do not place the centrifuge on the unstable place such as moving table or cart 11 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 3 2 Power On off and Door Release 3 2 1 Power On off Action 1 After connecting the AC Power cord at the power socket in the right back of the instrument turn on the Earth leakage Breaker Switch
11. SCANLAF SCANSPEED Multi Purpose High Speed Centrifuge ScanSpeed 1236R 1248R User s Manual LaboGene ApS Industrivej 6 8 DK 3540 Lynge T 45 3940 2566 F 45 4498 1741 info labogene com www LaboGene com DOC No C09DC00202 11 1 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R e E The LABOGENE s quality design that enhances performance operation and practicality gives a new dimension to centrifugation THE BEST FUNCTIONAL QUALITY SAFETY and ROBUSTNESS www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R BE Hanufactured and tested to IEL standards stable spining operation within P variation Steady and soft deceieration wath dynamic brake technology B High capacity strong compressor maures Fast cooling of chamber and samples B Fast cool function 4 C im 5 minutes for fast start up and fast coal down of sample Automatic recognition and alarma for imbalance over speed and over heat E Automatic retor identification functions W Triple o double Bminated ARS Steel door construction minimized anise and heat BB Safety door lock mechanism pesares the door 16 locked whilst is operation mede Unique doar drop protection protects the operator and Samples when amd unloading B Avtonotic detection and alarms for imbalance excess speed and heating W Emergency door aci release helps fo open The instrument
12. al to ensure correct usage through understanding Incorrect handling of the instrument could possibly result in personal injury or physical damage on the instrument or its accessories 1 ALWAYS locate the instrument on a flat rigid and stable place capable of withstanding weight of the instrument and resisting vibration 2 ALWAYS make a safety zone of 30 cm around the centrifuge to indicate that neither hazardous materials nor persons should be permitted within the area during operation v ALWAYS position the instrument with additional free space on each side of instrument to ensure proper air circulation 3 ALWAYS install the instrument within a temperature and humidity controlled environment Permissible ambient temperature 5 C 35 C Relative humidity 85 4 Should not use a power source other than the instrument designed to operate on 5 Should not use unapproved rotors and associated components v Only use rotors from LABOGENE ApS with appropriate centrifugal tubes and suitable adaptors to embrace sample containers tightly enough inside rotors 6 Before operating the instrument check if the rotor and the rotor lid are securely fastened v Should operate the instrument with a rotor properly installed and secured to the motor shaft 7 Mount the rotor on the motor shaft properly check it with spinning manually 8 Do not stop the rotor by touching with hand during the instrument is running 9 Emergency d
13. couple the rotor at first installation should turn off the instrument After coupling the rotor turn on the instrument and check the rotor recognition When you run a fixed angle rotor make sure that the rotor lid is tightly closed If you don t close the rotor lid completely it will be crushed LS v For operational safety this instrument has the automatic rotor recognition function 14 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 3 4 Balance Adjustment Final 1 Mount the rotor and place the balancing level on the middle of a rotor Confirm that air bubbles of all three windows of the balancing level are within the black lines 2 To adjust the balance status rotate the red colored ring at the wheel caster clockwise or counterclockwise until the device is well balanced 15 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 3 5 Positioning of Sample Tubes Action 1 Before loading sample tubes check the water drop or dirt in the rotor hole or inner bucket gt If there is a water drop or dirt in the rotor hole or inner bucket remove it with soft dry cloth 2 Tubes should be placed in the rotor with same amount of samples and symmetrical positions Only use appropriate centrifugal tubes and check the g force of sample containers before use gt For safety fill the sample for 70 8096 in the tubes Correct Way of Sample
14. ent s In compliance with EN 61010 7 Safety requirements for electrical equipment for measurement control and laboratory use General requirements EN 610710 2 020 Safety requirements for electrical equipment control and laboratory use Particular requirements for laboratory centrifuges EN 61000 6 1 Electromagnetic compatibility Generic immunity emission standard EN 50 11207 Acoustics Noise emitted by machinery and equipment Following the provisions of 2006 42 Machinery Directive as amended 2006 55 Low Voltage Directive as amended 2004 108 EC EMC Directive as amended 2011 65 EU RoHS Directive 2012 19 EU WEEE Directive Lynge January 2013 Rasmus S rensen QA Manager LaboGene ApS Industrivej 6 8 Vassingered 3540 Lynge Denmark 08012013QA SCANSPEED Declaration of conformity We declare under our responsibility that the following product Model ScanSpeed 1248R Refrigerated Multi purpose Centrifuge to which this declaration relates is in conformity with the following standard s directives or other normative document s In compliance with EN 61010 7 Safety requirements for electrical equipment for measurement control and laboratory use General requirements EN 610710 2 020 Safety requirements for electrical equipment control and laboratory use Particular requirements for laboratory centrifuges EN 61000 6 1 Electromagnetic compatibility Generic immun
15. gt Speed setting unit 10 rom or 100 rpm Setting RPM 1 Touch the RPM RCF button once gt RPM MODE is generated with pressing a RPM RCF button Once gt RPM LED is flickering at the display window 2 Touch the A Y buttons to change input value gt After keeping holding finger on the AW buttons for 5 seconds the unit of setting value is changed to 100 rpm from 10rpm gt If you not touch the A wW button for 5 second the setting mode is cleared 3 Touch the Enter button to complete the setting p Press Enter to save the setting value Setting RCF gt Speed setting unit 1 rcf or 10 rcf 1 Touch the RPM RCF button once gt RPM MODE is generated with touching a RPM RCF button once gt RPM LED is flickering at the display window 2 Touch the AW buttons to change input value l T Y Erbi i gt SY E mam _ w F Ee lt P Vv MY E m aF Fr Erin iW www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R gt After keeping holding finger on the A W buttons for 5 seconds the unit of setting value is changed to 10xg from 1xg gt If you do not touch the Y button for 5 second the setting mode is cleared 3 Touch the Enter button to complete the setting 4 3 Setting Time gt Speed setting unit 1hr 1min or 10 min
16. instrument 1 If you need to move or ship the instrument be cautious to protect the shaft from any physical impact or turbulence 2 Do not mount a rotor in any cases of movement Fill inside the chamber with proper materials to keep the shaft on place and not to be influenced by physical pressure 26 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 6 Trouble Shooting 6 1 Check list Power failure Don t run Can t open the door Can t close the door Noise and vibration during running Check list Connect the AC Power cord and make sure that the line is completely connected between the instrument and power outlet Check the power switch is turned on Please refer to 3 2 Power On off and Door Release If the door is not closed completely the instrument can t run Check the Door LED on the display window and close the door completely If the power is out check the leakage indicator to supply the power If it is not solved in shortly open the door with emergency door tool manually for safety of sample Please refer to 4 9 Emergency Door Open Remove the dirt at the door latch and then close the door completely again If the instrument is installed on the unstable floor please install again on the solid flat floor horizontally If the rotor is not coupled appropriately disassemble the rotor and then check the appearance of rotor If you find the damage of rotor im
17. ity emission standard EN 50 11207 Acoustics Noise emitted by machinery and equipment Following the provisions of 2006 42 Machinery Directive as amended 2006 55 Low Voltage Directive as amended 2004 108 EC EMC Directive as amended 2011 65 EU RoHS Directive 2012 19 EU WEEE Directive Lynge January 2013 Rasmus S rensen QA Manager LaboGene ApS Industrivej 6 8 Vassingered 3540 Lynge Denmark 08012013QA
18. mediately discard it Please refer to 3 3 Rotor coupling and disassembling Check balances of samples in the rotor Please refer to 3 5 Positioning of Sample Tubes and load the same weight of samples symmetrically 27 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 6 2 Troubleshooting Table If the instrument shows the error code with beeping sound press STOP button to stop the beeping sound and press Enter button to release of the error status and make the instrument go to the default setting again Error Possible Causes Actions Shut off the power supply and then turn on the power switch again to check the instrument Error 1 RPM Sensor If the error code shows continuously although you try to operate again please contact us If the door is not closed completely this message is appeared Remove the dirt at the door latch and then close the door completely again Check the Door LED on the display window If it is Error 2 Door f not solved in shortly open the door with emergency door tool manually for safety of sample Please refer to 4 9 Emergency Door Open If the motor is overheated this message is appeared Shut off the power supply for an hour and then turn on the power Error 3 Motor Overheating switch for checking the instrument If the error code shows continuously please contact us If the power input of Power supply V Hz is 10 less than req
19. normal electricity comes back 25 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 5 Maintenance 5 1 Outer part of instrument 1 Clean the outside of the instrument with dry soft cloth If necessary dip the cloth in neutral detergent and clean contaminated area Keep completely dry after cleaning 2 Do not use any volatile chemicals such as alcohol and benzene etc 3 Be careful not to make scratches on the surface of the instrument The scratches can cause corrosion on the surface of the instrument v rust appears clean it with neutral detergents and keep dry 5 2 Chamber 1 Keep dry inside the chamber after every use 2 If the chamber is contaminated dip the cloth in neutral detergent and clean contaminated area 5 3 Shaft 1 Always make special attention to clean the motor shaft to avoid any imbalance problem due to the contaminants 2 After using the instrument take out the rotor from the shaft and clean the shaft with dry soft cloth to keep dry 5 4 Rotor 1 If any parts are contaminated with samples clean the rotor with soft wet cloth and keep the rotor dry 2 Be careful not to make scratches inside or on the surface of rotors Any small scratches can cause corrosion of the rotor and big damage to the instrument 3 If you do not use the instrument keep the rotor separately from the shaft and stand it upside down 5 5 Transportation of the
20. ool buttons for fast cooling gt Fast Cool on LED is turned gt The display shows the message as follows Searching Rotor gt gt recognition OK gt By touching the Fast Cool button the instrument 15 refrigerated down to the set temperature in a short time During the fast cooling the rotor runs at low speed 1 000 rpm gt The passed time is showed on Time display If you d like to load your sample tubes before pressing the Fast Cool button it should be checked if the sample is safe during spinning at 1 000 rpm Before starting Fast Cooling please check the rotor coupling and symmetry of sample tube 20 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 21 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 5 Acceleration Deceleration Use the adjustment function of acceleration amp deceleration levels to protect sensitive samples Action 1 Touch ACC DEC button a E m 9 2 Touch the AW buttons change input ACC value gt ACC blinks on the display gt Input the desired level of ACC from 1 to 5 Level 5 T The fastest acceleration ACC 5 gt If you do not touch the A Y button for 5 second r Erin the setting mode 15 cleared 3 Fix the ACC level by touching Enter button 4 Touch the A Y buttons to change inp
21. oor open should be performed only when spinning is completely stopped 10 Should not exceed the rated speed or specific gravity Samples whose density is greater than 1 2g ml must have reduced maximum rotational speed to avoid rotor failure 11 The sample content should not exceed 80 of total capacity of a tube Otherwise it would cause 7 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 12 i 14 15 16 17 18 spillage of sample fluid and even the tube breakage ALWAYS load the tubes symmetrically with evenly weighted samples to avoid rotor imbalance If necessary use the water blank to counterbalance the unpaired sample The operation speed should not exceed the lowest value of the individual guaranteed g forces among the centrifuge rotor bucket or adaptors and sample container especially the guaranteed g force of sample container should not be neglected The rotors should be cleaned and kept dry after every use for longer life time and safety ALWAYS disconnect the power supply prior to maintenance and servicing to avoid electrical shock ALWAYS use proven disinfection procedures after centrifuging biohazardous materials Should not centrifuge flammable toxic radioactive explosive or corrosive materials When it is necessary to use toxic or radioactive materials or pathogenic micro organisms which belong to the Risk Group I of WHO Laboratory Bio safety Manual
22. peed Centrifuge ScanSpeed 1236R amp 1248R SCANSPEED Declaration of conformity We declare under our responsibility that the following product Model ScanSpeed 1236R Multi Purpose Refrigerated High Speed Centrifuge to which this declaration relates is in conformity with the following standard s directives or other normative document s In compliance with EN 61010 1 Safety requirements for electrical equipment for measurement control and laboratory use General requirements 610170 2 020 Safety requirements for electrical equipment control and laboratory use Particular requirements for laboratory centrifuges 61000 6 1 Electromagnetic compatibility Generic immunity emission standard 50 11201 Acoustics Noise emitted by machinery and equipment Following the provisions of 2006 42 Machinery Directive as amended 20055 575 Low Voltage Directive as amended 2004 108 amp C EMC Directive as amended 2011 65 EU RoHS Directive 2012 19 EU WEEE Directive Lynge January 2013 Rasmus S rensen QA Manager LaboGene ApS Industrivej 6 8 Vassingered 3540 Lynge Denmark 08012013QA SCANSPEED Declaration of conformity We declare under our responsibility that the following product Model ScanSpeed 1236R Multi Purpose Refrigerated High Speed Centrifuge to which this declaration relates is in conformity with the following standard s directives or other normative docum
23. uired power this message is appeared Error4 Low voltage Shut off the power supply and then check the voltage of the Power supply V Hz Use AVR to provide proper power If the power input of Power supply V Hz is 10 more than required power this message is appeared Errors High voltage Shut off the power supply and then check the voltage of the Power supply V Hz Use AVR to provide proper power If the instrument is spun with over speed there will be some problems in the overload of motor and the output of motor Error6 Over speed Shut off the power supply and then turn on the power switch again to check the instrument If the installed software has bugs this message is appeared Error 7 Software f Tuning the firmware Download 28 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R Check weight balances of samples Please refer to 3 5 Positioning Error8 Imbalance of Sample Tubes and then turn off and on the instrument for checking If the function of rotor recognition is failed this message is appeared Coupling the proper rotor exactly Please refer to 3 3 Error 9 Rotro ID Rotor coupling and disassembling Check the existence of the rotor If the rotor is absent mount a rotor Any wire disconnection or tuning of the instrument must be performed only by a service engineer who is authorized by LABOGENE ApS 29 www labogene com Large Capacity High S
24. ut DEC value gt DEC blinks on the ACC DEC display gt Input the desired level of DEC from 0 to 5 Level 0 Natural deceleration Level 5 Fastest deceleration gt If you do not touch the A Y button for 5 second the setting mode is cleared 5 Fix the DEC level by touching Enter button 22 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 6 Program Saving amp Recalling Action 1 Set parameters Refer 4 2 4 4 2 Touch the PROG button longer than 3 seconds gt Check the message of PROGRAM SAVE at the display 3 Touch the AW buttons to change input Program number gt If you do not touch the A Y button for 5 second the setting mode is cleared gt Save up to 100 programs 4 Touch the Enter button to complete the saving Recalling 1 To recall the saved program just touch the PROG button 4 m shortly less than 1 5 gt Check the message of PROGRAM CALL at the display N 2 Touch the A Y buttons to select program number you want to recall and then touch the Enter button gt If you do not touch the A W button for 5 second the setting mode is cleared gt When you touch the Enter button display window show the saved setting parameters RPM RCF TIME TEMP and ACC DEC 23 www labogene com Large Capacity High Speed Centrifuge ScanSpeed 1236R amp 1248R 4 7 Pulse
Download Pdf Manuals
Related Search