User-RRC.330US & RRC.330USA
Contents
1. 25 100 mm RRC 330 RRC 330 A SET UP Plug the Power Supply Output Cable to the Power Jack on the Rear Panel of the Unit Plug the Power Supply into a suitable AC Power Outlet Rotate the SPEED Control to minimum full counter clockwise position Place the Power Switch on the rear of the Unit to the ON 1 position OPERATION Place the STOP RUN Switch in the STOP Position The Take Up Spindle on the right rotates in a counter clockwise direction Note that you can Wind In or Wind Out depending on which way you place the Label Roll on the Roll Holder right side up or upside down The plastic Ring on the first Rotating Paper Guide can be used if the unwind roll is unevenly wound Setting the Ring at the proper height will help correct the unevenness of the Roll on the rewind side It is recommended to lower the speed if the unwind Roll is very uneven Place an empty label Core not included over the Take Up Spindle run the labels behind the Guide Rollers and secure the Label Web using a piece of tape Lower the blue Label Senor Assembly so that the labels run through the gap in the Sensor Assembly Reset the Counter to zero Verify that the SPEED Maximum Variable Switch on the left side of the Unit is set to Variable Rotate the SPEED Control Knob on the top Panel fully counter clockwise Start by switching to RUN and slowly The machine will stop when out of labels or when the preset Label Coun2. IONS OF MERCHANTABILITY SATISFACTORY QUALITY AND OR FITNESS FOR A PARTICULAR PURPOSE NO OTHER PERSON AGENT DEALER OR RESELLER IS e Unpacking and Repacking Instruction Sheet AUTHORIZED TO GIVE ANY WARRANTIES ON BEHALF OF LABELMATE ANY OBLIGATION TO e User Manual this document WARRANTY OTHER THAN THAT SPECIFICALLY ADDRESSED HEREIN IS EXPRESSLY DISCLAIMED e Separate User RRC USA Sensor Set up Procedure Sheet e Separate manufacturer s Data Sheet for Counter Module e Power Supply and Line Cord A Line Cord is supplied only for North American destinations Because of the many variations in mains plugs LABEILM ATE U S A Lic the Line Cord must be supplied locally for other destinations 12A Sunset Way Henderson NV 89014 USA Retain the Shipping Container and Packaging for Storage and Transport 702 435 8535 FAX 702 435 8536 ines 877 RE h USA KEEP MANUALS IN A SAFE PLACE FOR FUTURE REFERENCE support labelmateusa com www labelmateusa com WARNING This product is for indoor use only Not for use in wet locations Unplug unit before removing waste material or performing any cleaning or maintenance services A SPECIFICATIONS Size Overall envelope HWD 13 x33 x9 330x584x229 mm Power Power Supply 100 240vac 50 60Hz Output 24vdc 4 17A Roll Width 6 5 170 mm Depending on Roll Diameter Core Diameter RRC 330 USA Unwind amp Rewind 3 76 mm RRC 330 AU Unwind 3 76 mm Rewind 1 4
3. Product Limited Warranty LABE LMAT U SA LLC Labelmate USA warrants to the original end user customer that Labelmate USA products will be free from defects in materials and workmanship for the duration described herein below Labelmate USA s Limited Warranty covers only those defects that arise as a result of normal use of the products and does not cover any other problems including those that arise as a result of i improper maintenance or modification ii parts or supplies not provided or supported by Labelmate USA iii operation outside the products Universal Reel to Reel Counter specifications or iv unauthorized repair modification or misuse Use of any unauthorized accessory or eo ea eee RRC 330 US amp RRC 330 USA The Warranty period for all products commences the date of shipment from Labelmate USA and accrues to the original end user customer Warranty coverage is non transferable and terminates immediately upon rental resale or any other change in ownership Original purchase documentation should be retained for Warranty coverage verification e e In the event Labelmate USA substantiates during the applicable Warranty period a defect in any product 330US Fixed 3 2 Rewind Core Holder which is covered by Labelmate USA s Warranty Labelmate USA shall repair or replace the product at Labelmate USA s option Labelmate USA retains sole discretion to determine whether or not a product is 399 39 s defective In no
4. cell that detects the end of Labels and stops the RRC should be calibrated for the label web being used Here s how Place the RRC STOP RUN Switch in the STOP Position Place a Label Liner ONLY no label in the Label Sensor Gap 1 Using a small flat bladed screwdriver adjust the Photocell Adjust Control until the green Photocell Adjust LED illuminates or 2 Adjust Photocell Adjust control for 3 to 5 VDC at the Photocell Test Jack 3 5 mm Plug Remove the label liner from the Sensor Gap and observe that the voltage falls to 0 25VDC or less Either method yields identical results Please refer to the included Counter Specification sheet for details of the digital Counter operation and to the Sensor Set up Instruction Sheet for details of adjusting the Sensor Mode and sensitivity in the event you are counting difficult labels Any questions or comments please call or e mail us See back cover
5. event shall Labelmate USA have any obligation to repair or replace until the customer 330 USA 4 Adjustable Core Holder returns the defective product to Labelmate USA The customer assumes any and all responsibility and liability associated with transportation of products for service under this Warranty WARRANTY PERIOD PRODUCTS COVERED CAT and Mini CAT Label Rewinders Label Counters Excluding Counter Displays and Encoders Universal Label Sensing Label Dispensers Excluding Counter Displays Label Slitters Mechanical Parts Only and excluding Counter Variable Speed Control 3 Years Displays Bypass Switch for Maximum Speed Reel to Reel Machines Excluding Counter Displays and En coders High speed Motor Standard Print Mechanisms Excluding Counter Displays and Encoders Quick Chucks Power Supplies AC DC Adaptors and Transformers Counter Displays Encoders Any other products or parts not specified herein RRC 330 USA Reel to Reel Counter 180 Days Out of Warranty Repairs In the event your product requires service or you have questions regarding Warranty coverage please call Remove all parts from shipping container and verify contents toll free 877 833 7149 inside the United States or 1 702 435 8535 outside the United States 13 330 mm Roll Diameter Capacity 1 Year LABELMATE MAKES NO OTHER WARRANTY OF ANY KIND WHETHER EXPRESS OR IMPLIED Package Contents WARRANTIES OR CONDIT
6. t is reached To re start first place the SPEED Maximum Variable Switch to the VARIABLE Position Turn the SPEED Control CCW to minimum and place the STOP RUN Switch in the STOP position Load labels on the Unwind Core Holder and tape the Label Liner to the Rewind Core RRC 330 A ONLY USING THE ADJUSTABLE CORE HOLDER ACH Unlock the three Locking Levers underneath the take up Flange by turning them clockwise Reposition the Lever Arms if necessary by pulling straight down and rotating them to a convenient position While holding the Take Up Flange Plate rotate the Black Plate underneath the Take Up Flange to bring the Fingers together Place your Take Up Core over the Fingers about half way down and rotate the Black Plate again to bring the Fingers in contact with the Core Lock the Locking Levers by turning them counter clockwise looking from the top Push the Take Up Core all the way down on the Fingers The Core should now be held tight on the fingers If its not tight enough re do the operation If necessary for easy removal of the roll from the ACH loosen one of the Locking Levers temporarily Then remove the Roll and re tighten the Locking Lever Once the ACH diameter is set you can put the next empty core on the ACH without readjusting the Locking Levers NOTE Keep the Unwind Plate clean of particles and label adhesive END OF ROLL PHOTOCELL ADJUSTMENT The sensitivity of the Photo
Download Pdf Manuals
Related Search