Patriot V – user manual
Contents
1. Control and setting of the communication module is carried out by means of SMS commands from a mobile telephone and sending them to the telephone number of the SIM card placed in the control unit of PATRIOT V communication module During each command input it is necessary to input the safety code lt code gt which is preset to 1111 e g in the form 1111 After take over of the vehicle with installed communication module carry out according to hereinafter described procedure change of the safety code 1111 to your new safety code personal safety code For this code select 4 digit combination which you remember well or which you use for other purposes credit card etc 1 Change of the safety code To change the safety code preset to 1111 input SMS command in the form lt code gt CODE lt code1 gt e g 1111 CODE 2222 where lt code gt is original 4 digit safety code preset to 1111 lt code1 gt is your new 4 digit safety code IMPORTANT CAUTION Remember your new 4 digit safety code very well 2 Inputting telephone numbers If you wish to use the communication module security functions it is necessary to input at least one telephone number This telephone number is necessary for entitlement to voice communication with the module and for transfer of alert information Maximum number of positions for inputting telephone numbers is 5 Positions which will not have any telephone numbers assigned will be ignored For2. PATRIGT GSM TEC HNO LOG Y Electronic LogBook ON LINE USER MANUAL CONTENTS COntroland secs lagers 02 Change of the safety code eee 02 Inputting telephone NUMbETS 6 cece cee cee ere ee ee eases eee tee 02 Switching the communication module 03 OUTPUT COMM aaa Alors 03 Information about the communication module StatuS cece cece 04 TESH 04 V ltage drop NfO ON 2 Post eee 04 Private business drive eva ek ead rtrt uttu tr unutur ae ve ant ae pares 05 Identification of the 05 chest tena sate trace cb 05 Technical 05 Pe User manual_PATRIOT V_eng_15 10 2008 doc CONTROL AND SETTING
3. e g 1111 TEL After carrying out the command the communication module sends confirming SMS with data about input telephone numbers to the mobile phone which the command was sent from e g in the form TEL1 420602123456 AO TEL2 not input TEL3 not input TEL4 not input 5 not input Deleting of the telephone number can be carried out by inputting an SMS command in the form lt code gt lt n gt TEL e g 1111 1TEL where lt n gt is position of input telephone number 1 5 User manual_PATRIOT V_eng_15 10 2008 doc After carrying out of the command the communication module sends a confirming SMS with data about input telephone numbers not input will be mentioned instead of deleted telephone number to the mobile phone which the command was sent from e g in the form 1 not input TEL2 not input TEL3 not input TEL4 not input 5 not input 3 Switch ON OFF of the communication module This function serves to switch off transfer of alert notifications We recommend using this function esp during service repairs accident module breakdown etc To switch the alert transfer notification ON input SMS command in the form lt code gt PATRIOTON To switch the alert transfer notification OFF input SMS command in the form lt code gt PATRIOTOFF where lt code gt is original 4 digit safety code preset to 1111 if not changed by client previously After carrying out the command th
4. correct function of the communication module in the Czech republic as well as abroad it is necessary to input telephone numbers in international format e g 420 123456789 country code personal telephone number To input the telephone numbers send SMS to the SIM card telephone number placed in the communication module SMS should be in the form lt code gt lt n gt TEL lt telnumber gt lt a gt lt b gt lt c gt e g 1111 41TEL 420602123456 0004 lt code gt 4 digit safety code lt n gt position of input telephone number 1 5 lt telnumber gt telephone number in international format e g 420 602 123456 lt a gt alert filter for input telephone number 0 all alerts 1 alarm 2 voltage drop If you do not wish to change manufacturer s setting written in bold of complementary parameters for the telephone numbers it is possible to input SMS in abbreviated form lt code gt lt n gt TEL lt telnumber gt e g 1111 1TEL 420602123456 After carrying out the command the communication module sends confirming SMS with data about input telephone numbers to the mobile phone which the command was sent from e g in the form TEL1 420602123456 AO TEL2 not input TEL3 not input TEL4 not input 5 not input The other telephone numbers can be input with the same procedure If you wish to verify if you input the telephone number correctly send SMS command in the form lt code gt TEL
5. e communication module sends a confirming SMS with data about switching ON switching OFF to the mobile phone from which the command was sent in the form PATRIOT ON OFF 4 Output control PATRIOT V communication module has 2 independent outputs through which it is possible to by means of SMS control siren engine block independent heating etc Caution Verify with your installer which outputs are connected All outputs can be controlled by means of SMS commands sent to the telephone number of the communication module in the form al switching on lt code gt lt n gt ON e g 1111 10N where lt code gt is original 4 digit safety code preset to 1111 lt n gt is the number of demanded output After carrying out this command the module makes connection of relevant output b switching off e g 1111 10FF lt code gt lt n gt OFF where lt code gt is original 4 digit safety code preset to 1111 lt n gt is the number of demanded output After carrying out this command the module disconnects the relevant output c short impulsion turning ON and OFF lt code gt lt n gt IMP where lt code gt is original 4 digit safety code preset to 1111 lt n gt is the number of demanded output After carrying out this command the communication module will make a short connection 2s of the relevant output Further after carrying out this command the communication module will send a confirming SMS to the mobile phone from which the comma
6. er reception of the command the communication module sends an SMS with confirmation of starting the test in the form Test ON Afterwards the alert sequence is started automatically It means that input telephone numbers receive according to chap 3 SMS with text and data about actual position of the vehicle in the form Control test GMT TIME 26 01 2005 12 16 N 4935 7839 E 01715 0335 SPEED 0 km h and then SMS alert notifications Control test and Microphone ON are transferred to the telephone numbers input according to chap 3 7I Voltage drop information During voltage drop under 10V for the time longer than 1 minute the communication module sends alert information to the telephone numbers input according to chap 3 in the form Voltage drop This function informs the user about gradual discharging of the power source in the vehicle e g lights on after the drive Ben User manual_PATRIOT V_eng_15 10 2008 doc 8 Private business drive switch only at the LogBook application This switch can be used only at the LogBook application to identify the sort of the drive private business 9 Identification of the driver DALLAS chip only at the LogBook application the chip is not a part of the kit To use the driver identification function only at the LogBook application it is necessary to order the DALLAS set which consists of a DALLAS reader and DALLAS identification chip 10 Manufacturer s s
7. etting PATRIOT V communication module is delivered in the following preset gt safety code lt code gt 1111 gt no telephone numbers are input TEL 1 5 not input gt sort of delivered alarms 0 all gt outputs 1 2 switched off Switch 1 2 OFF 16 Basic technical specifications Voltage range 9 24V DC Power consumption in stand by status 19 mA average value Operating temperature range 25 C to 55 C GSM Tri band 900 1800 1900 MHz Dimensions I x w x h 120 x 60 x 25 mm Weight 130gr User manual_PATRIOT V_eng_15 10 2008 doc SMS COMMANDS SUMMARY COMMAND FUNCTION REPLY lt code gt CODE lt code1 gt Change of the safety code The code is xxxx TEL1 420602123456 AO lt code gt lt n gt TEL lt tel Telephone numbers input TEL2 not input number gt lt a gt 3 not input TEL4 not input TEL5 not input TEL1 420602123456 AO TEL2 not input lt code gt TEL Telephone numbers input 3 not input verification TEL4 not input 5 i not input not input not input lt code gt lt n gt TEL Delete telephone number not input lt code gt PATRIOTON Switching alert transfer PATRIOT ON OFF lt code gt PATRIOTOFF ON OFF lt code gt lt n gt ON lt code gt lt n gt OFF Output control Switch n ON OFF IMP lt code gt lt n gt IMP Vehicle at rest in motion Alarm deactivated activated Switch 1 ON Communication module sta
8. icle at rest in motion Car alarm deactivated activated Switch 1 ON Switch 2 OFF GMT TIME 26 01 2005 12 16 N 4935 7839 E 01715 0335 SPEED 0 km h Caution to detect the status of the communication module transfer of alert notifications must be allowed see ch 3 Information about the vehicle status This function tests the status of the ignition key in the vehicle If the ignition key is in ON position the communication module interprets this status in information about the communication module status as Vehicle in motion and if the ignition key is in OFF position than this status is interpreted in information about the communication module status as Vehicle at rest Information about car alarm status This function tests brown wire connected to the car alarm In case of activated car alarm Car alarm activated will be mentioned in the information about the communication module status in case of deactivated car alarm there will be mentioned Car alarm deactivated Information about vehicle position This function allows detecting actual position of the vehicle in which the communication module is installed 6 Test Test of SMS and voice alerts transmission can be carried out by sending an SMS command to the telephone number of the SIM card placed in the communication module in the form lt code gt TEST e g 1111 TEST where lt code gt is original 4 digit safety code preset to 1111 Aft
9. nd was sent in the form Switch n ON OFF IMP Caution after switching the output ON the power consumption of the communication module highly increases Engine block for controlling of engine immobilisation only output Nr 2 is used According to the E U legislative the engine block is possible only if the vehicle is at rest Practically it means that engine block is activated after ignition key is switched off and then it is impossible to start the vehicle again To switch engine block on it is impossible to start the vehicle input an SMS command in the form lt code gt 2ON e g 1111 20N where lt code gt is original 4 digit safety code preset to 1111 To switch engine block off it is possible to start the vehicle input an SMS command in the form lt code gt 2OFF e g 1111 20FF where lt code gt is original 4 digit safety code preset to 1111 User manual_PATRIOT V_eng_15 10 2008 doc 5 Information about the communication module status To receive information about the communication module status and the vehicle position send the SMS command to the telephone number of the SIM card inside the communication module in the form lt code gt STATUS e g 1111 STATUS where lt code gt is safety code preset to 1111 After carrying out the command the communication module sends a confirming SMS with data about status and vehicle position to the mobile phone which the command was sent from in the form Veh
10. tus Switch 2 OFF lt code gt STATUS information GMT TIME 26 01 2005 12 16 N 4935 7839 E 01715 0335 SPEED 0 km h Control test GMT TIME lt code gt TEST Test 26 01 2005 12 16 N 4935 7839 E 01715 0335 SPEED 0 km h www auto gps eu User manual_PATRIOT V_eng_15 10 2008 doc
Download Pdf Manuals
Related Search