PEDICURE SPA USER MANUAL
Contents
1. BACK REST 1 To set backrest up Lift up the backrest until a Click is heard Make sure the lever is locked before operating 2 To fold down backrest Lift up lever handle located on the left side bottom of Chair Installation Plumbing Connections A N Warning 4 5 Before any connection pay attention to these subjects Debris or residue may become lodged into the Hot and Cold hoses during construction which may clog the Hot and Cold Mixer To clean drain a good amount of water from water hoses to bucket before connecting them to the pedicure spa Failure to do so may void your Warranty Hooking up a used Hot Cold flex hose is not recommended since debris from broken rubber seal might clog water mixer Failure to do so may void your Warranty Backflow preventer Due to differences in construction lay out of your Salon and City s plumbing code please contact your local Plumber to fulfill your needs as required Backflow Preventers are not supplied by the pedicure spa manufacturer Check valve is an optional part and supplied free of charge for your convenience Factory is not liable for this Check valve Maximum Inlet water pressure must be under 75 PSI Power Drain 1 2 ID Cold Water 3 4 Check Valve See Installation Instruction attached with supplied CheckValve Installation Gravity Drain Under Ground 1 2 ID Cold Water __ 1 2 ID Hot Water 11 2 pipe 11 4 pi2. Lexor Pioneering Smart Pedi Spas PEDICURE SPA USER MANUAL LUMINOUS Before Operating the unit please read this manual thoroughly and retain it for future reference RECEIVING AND INSPECTION PLEASE TAKE NOTE Thoroughly inspect each shipment immediately upon arrival It is important that you notify the driver and insist on a notation of the damage Make this notation directly on the freight company s waybill or bill of lading Failure to note damage on the waybill or bill of lading may impede and or prevent any claims that you may have against the freight carrier If missing parts or damage is found Please notify the carrier at once and request an inspection DO NOT DISCARD THE SHIPPING BOX If you give the carrier a clear receipt for goods that have been damaged in transit you do so at your own risk and expense TRADEMARK DISCLAIMER Infinity Sani Drain PureFlo Pioneering SMART Pedi Spa Auto Fill AutoClean and Tru Touch are the registered trademarks of Lexor Inc Reproduction or reuse of part or all of trademarks are expressly prohibited without written permission from Lexor Inc Due to limitation of the printing process product colors shown might look different from actual colors Lexor will not be responsible for any misprint of this advertisement Lexor s footspa specification and prices may change without prior notice Pedicure Spas are intended for professional used only always follow your State
3. Press and hold until desired backward customer chair position is achieved 5 Seat Adjustment Forward Press and hold until desired forward customer chair position is achieved 16 Operation and Care and Care JET COVER REMOVAL amp INSTALLATION 1 Turn Counterclockwise to remove Turn Clockwise to install Motor amp Housing impeller Jet Cover PureFlo Label Operation and Care JET HOUSING REMOVAL amp INSTALLATION 1 Turn clockwise to remove motor Turn counterclockwise to install motor Operation and Care MASSAGE SYSTEM amp REMOTE CONTROLLER 1 Press Auto Button to start Auto mode Press again to turn off massage Auto and Manual mode will run for duration of 20min 2 Press any button Rolling Spot Kneading Tapping Combine to enter Manual mode 3 Press Rolling Spot to stop rolling up down and stop at desired spot 4 Press Intensity button to select tapping intensity 5 Vibro Button is an option Pressing this button will resume with Tapping action 6 Press any chair button Recline Incline Backward Forward to move the chair to desired positions 19 Operation and Care and Care NOTE If the Massage Chair is not provided then the end user will need to install a UL listed and cUL CSA certified massage chair with a suitable Class 2 Power Supply TOP MASSAGE CHAIR BASIC INSTALLATION INSTRUCTIONS Fig 2 Install seat cushion with 2 screw Knobs Drill 4 mounting
4. THIS MANUAL IS REQUIRED FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY AND OR WARRANTY WILL BE NULL YOU MUST HAVE A QUALIFIED LICENSED PLUMBER TO CONNECT THE SPA IN PLACE SAFELY UL SAFETY RECOGNIZED FOR UNITED STATES AND CANADA 2012 All Rights reserved Design and Specifications are subject to change without notice 23 VERSION 100912
5. or disciplinary action Each foot spa that is not in compliance with this section may result in a separate violation NOTE Authority cited Section 7312 Business and Profession Code Reference Section 7312 e Business and Professsion Code Below is a suggestion for your pedicure spa chair s cleaning procedure After Each Customer All water shall be drained and all debris shall be removed from the spa basin 2 The spa basin must be cleaned with soap or detergent and water 3 The spa basin must be disinfected with an EPA registered disinfectant with demonstrated bactericidal fungicidal and virucidal activity which must be used according to manufacturer s instructions 4 The spa basin must be wiped dry with a clean towel At the End of Each Day 1 The screen shall be removed all debris trapped behind the screen shall be removed and the screen and the inlet shall be washed with soap or detergent and water 2 Before replacing the screen the screen shall be totally immersed in an EPA registered disinfected with demonstrated bactericidal fungicidal and virucidal activity which must be used according to the manufacturer s instructions 3 The spa system shall be flushed with low sudding soap and warm for at least 10 minutes after which the spa shall be rinsed and drained At Least Once A Week 1 The spa basin shall be filled completely with warm water and 1 teaspoon of 5 25 bleach for each gallon of water or a solut
6. Board s sanitation and disinfectant guideline Design and Specifications are subject to change without notice Table of Contents RECEIVING AND INSPECTION oso 1 SAFETY PRECAUTIONS finirla rina 3 PARTS Identifying Parts for LUMINOUS Model uiiii 4 INSTALLATION SPA to SPA RECOMMENDED CLEARANCE i e 5 MANICURE TRAY ARMREST solo edo 6 Piumbing GONNEGlonNs A Lee 8 FN NE 8 SAY DAN Under Ground aar me 9 Plumbing Flow Pattern for Power Draini e 9 Plumbing Flow Pattern f r Gravity D nLsisssunsssinsennsainemosneneiesupetsnsenndensanse 10 Hot nd Gold Water SUPDN LINES av a a 10 SPA SPECIFICATION Electrical and Pedicure Spa Component Specifications ereer rrenen 12 OPERATION AND CARE AUF MOdelS vare 13 PAUTO PI 3 AUTO D ral NOTES scrittoio diparte 15 Front Panel Functional amp Operating Instructions 16 Jet Cover Removal amp InstallatioN cess cece eeteueessaeesseeesseeseneeeas 17 Jet Housing Removal amp Installation 18 Massage system and Remote Control serseri i nens 19 Safety Requirements for Pedicure Spas 210 WARRANTY LEXOR LIMITED FACTORY WARRANTY aaa 22 Safety Precautions READ AND FOLLOW INSTRUCTIONS CAREFULLY SAFETY PRECAUTIONS A N Warning THIS PRODUCT IS FOR INDOOR USE ONLY DISCONNECT POWER SUPPLY CORD BEFORE SERVICING This product is to be connected to a bra
7. EDICURE SPA SPECIFICATIONS e Construction Marble composite high gloss acetone proof gel coat Two 2 electro mechanical knobs control the drain and whirlpool found on Auto Fill only models One 1 Digital Automated System Control Panel found on AutoClean models only Electro mechanically operated reclining massaging and sliding seat with hand held control One 1 pipe less whirlpool jet Pipe free technology Power drain or Gravity drain Extendable water spray positioned well above water line air gap is accommodated with back flow prevention required by plumbing code e Depending on pedicure spa model arms may swing open swing up down or slide forward backward SPECIFICATIONS Spa Dimensions amp Weights Luminous Spa seat up right L 52 132cm W 33 84cm w Tray 44 112cm H 56 142cm Spa fully reclined L 74 180cm H 46 112cm Empty Weight 200 lbs Shipping Weight 260 lbs Pedicure Stool 12 13 Adjustable Stoo Manicure Stool 16 25 20 Spa Water Capacity 4 US Gallon Jet Motor 120 VAC at 85W 60Hz Massage Motors Seat Sliding amp Reclining 24VDC 2 5A x 5 Discharge Pump Motor 120V at 85W 60 Hz Maximum vertical lift 3ft Flow rate 500 GPH floor level 115 VAC 60HZ 15A Power needed per spa chair 6 Amp Electrical Switches found on Auto Fill models only One 1 electro mechanical knob for the Whirlpool Rated at 5A contact One 1 electro mech
8. and equipment is used Discontinue use of the bowl until proper equipment is replaced You may be held accountable for any injury that may occur Lexor Inc is not liable for any injury that may occur STATES NOTICE In the common wealth of most of the States all pedicure spas shall be installed for Commercial usage in the states are required to have backflow preventer This equipment shall be installed between the water inlets and the spa at Salon s cost PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE 3 Identifying Parts Identifying Parts for LUMINOUS Model Pedicure Whirlpool with Massage System 1 Head Rest NM CON IA OW Chair Cushion with Massage Armrest Cushion Massage Remote Control Manicure Tray Angelic Bowl Calf Support Sani Drain System with discharge On Off Knob 9 Hot Cold Water Mixer Valve 10 Dual Function Auto Fill amp Jet On Off Knob 11 Flex Water Filler Spray Spout 12 Up Down Armrest 13 Handbag Purse Hook 14 Tub Light 15 Drain Stopper 16 17 18 19 Water Level Sensors Pure Flo Jet Low Profile Stool for Pedicure Digital Automated System Control Panel controller Optional found on AutoClean models Installation WALL CLEARANCE Installation MANICURE TRAY ARMREST Manicure tray Purse Hook 1 Plug In manicure trays and attach the purse hook 1 Supplied Installation
9. anical knob for the Drain Rated at 5A contact Installation should be made with connection at the external interface parts Please consult with your local plumber Safety Luminous Pedicure Spa is UL Listed Plug amp Play Installation Operation and Care and Care AUTO OPERATION Auto Fill Models Auto Fill Models Panel Functional Switches amp Operating Instructions Hot Cold water faucet located at the center of the front panel 1 1 Use faucet knob to adjust optimal water temperature at H Left or C Right directory 1 2 Pull out and tilt down faucet knob to shut off water any time during the automatic or manual operational cycle Drain Knob ___ O _L___Auto Fill Jet Knob Water Control Knob Hot Cold N vamia Water control knob must be used to shut off water supply to basin when spa chair is left unattended and overnight Water Control Knob Pull out knob in direction of arrow Tilt down knob to shut off water Automatic Auto Fill cycle Water will automatically turn off when optimal water level is detected by 2 sensors The Auto Fill cycle is safely protected by 2 sensors and can be extended with a manually operative shut off valve located at the front panel N oon Must scrub and clean water sensors frequently to ensure that water stops right at sensor level If necessary clean using sponge buffer 13 Operation and Care and Care Manual conv
10. charges to this warranty in any extent LIMITED DAMAGES Allowed by law Lexor will fully extend its options to disclaim and refuse any liability for substantial damages including but not limited to loss of business reputation decrease in profits or any fastidious damages other than these limited damages In some states the mentioned damages are not allowed to lawfully sustain therefore they may not apply to you Extended 1 Yr Warranty optional as an upgrade to be purchased prior to the shipment date of the original order Extended 1 Yr Warranty will cover the above mentioned including Tru Touch Massage System Warranty Parts Sale All parts purchased from Lexor Customer Care will have a 90 Day warranty from shipped date except Complete Chair Top with Massage System and Complete Spa Base with Plumbing Lexor reserves the rights to send out new or equivalent to new as replacements All part sales are final and no refunds will be accepted Complete Chair Top with Massage System will have a 6 Month Limited Warranty from the date of shipment Complete Spa Base with Plumbing Installed will have a 6 Month Limited Warranty from the date of shipment Continuing a policy of constant research and development to improve the quality of our products Lexor Inc reserves the right to change pricing parts design and specifications without prior notice or obligation Your Initials 22 WARNING PROPER INSTALLATION ACCORDING TO
11. container See illustration below 2 Replacement Spa Always use new hot cold water hoses when connecting a new spa chair to prevent debris such as old rubber particles from clogging drain 10 Installation CONNECT DRAIN WITH POWER DRAIN PUMP OR GRAVITY DRAIN NO PUMP Using schedule 40 PVC Power Drain or 1 4 flex tube Gravity Drain and appropriate traps Connect drain to meet local plumbing codes Rubber connection to the drain should be removable for easy service and should not be permanent to prevent damages Drain System Recommendation Detail A 11 Spa Specifications ELECTRICAL AND PEDICURE SPA COMPONENT SPECIFICATIONS All electrical connections MUST be made by a qualified licensed electrician in accordance with Local amp National Electrical and Building Codes A 110V 50 60 Hz 15 Amp GFCI protected grounded circuit MUST be used to supply power to the Pedicure Spa A dedicated circuit must be used with a GFCI All wiring must conform to National amp Local Electrical Codes N wannine IT IS EXTREMELY IMPORTANT THAT THE FOOT SPA OPERATES WITH GFCI PROTECTION VERY IMPORTANT Both back of chair and seat are adjustable When both are at maximum positions one must allow 18 44cm from back wall to foot spa This minimum distance assures unobstructed recline Failure to follow this required dimension might damage your spa components and plumbing connections which will void your warranty P
12. ersion Auto Fill option can be simply reset to normal manual mode as a contingent system when automatic operation becomes unavailable Please call our Customer care for step by step instructions Auto Fill Jet Switch Dual functional momentary switch located on the right side of the front panel 1 To turn water on Turn knob clockwise for 1 second and release Water will fill up to reach the sensor level and activate the whirlpool jets 2 To turn water off Turn knob clockwise for 1 second and release to turn off water The switch can be activated to turn on or turn off water any time during the Auto Fill cycle EXCEPT when water is at sensor level 3 To turn On Off the whirlpool jet Turn knob clockwise for 1 second and release This Jet cannot be turned on if water level is not at sensor level Turn this jet knob when water level is low the system will resume with fill up water prior activating whirlpool jet Drain Switch Dual Action Electro mechanical Switch located on the left side of the front panel When activating the switch it will raise the drain stopper and power up the drain pump if exist at the same time 1 To drain water Turn the drain knob clockwise Drain pump is activated 2 To turnoff the drain pump Turn the drain knob counterclockwise CAUTION Reset the Drain knob to vertical position to close the drain stopper prior starting Auto Fill 14 Operation and Care and Care Auto Fill amp Au
13. fter receiving the furniture by calling our Customer Care and opening a case Image s of the damage s and a signed Bill of Lading must be submitted Lexor will not cover any missing part or damage claims after 48 hrs WHAT IS NOT COVERED Mishandling damages from shipping expenses from returning eligible defectives to factory improper installation abuse misuse neglect accidental events freight damages damage resulting from a person standing in the Pedicure Spa s basin or other similar stress to that basin normal wear and tear on upholstery or natural disaster REQUEST FOR SERVICE Prior to calling please have your Salon or company name address telephone number contact name model name and serial number and a brief description of the problem Contact Lexor s Customer Care Department to report defects or if you have questions on warranty prior to the expiration date of warranty at www uspedicurespa com LENGTH OF WARRANTY Twelve 12 months starting from the date of shipment Purchase invoice bill of sale date of purchase or delivery receipt are required by Lexor to qualify for your warranty coverage UNAUTHORIZED REPAIR Any performed or attempted repair or modification on the spa without explicit authorization in writing from Lexor will void this limited warranty DISTRIBUTOR WARRANTIES There is no distributor dealer general contractor or other party has any legal rights to apprentice Lexor to any obligations or
14. holes 2 Width 16 5 Lever the back massage and secure 2 hinge Length 11 Install seat frame and secure 4 screws onto the metal brackets Do not turn screws from bottom base Using the provided the screws all the way in stand off to adjust the height of seat frame as Leave 1 4 thread screw head for sliding needed to allow seat frame to travel freely Install back shell with 4 screws as Fig 3 ET ng gt Controller PCB Lift up back massage to engage DE locking device Manually adjust ss actuator rod to lock as needed Install back cushions Plug AC cord to power strip Located inside of the tub base Fig 3 20 AN RING You must always refer to your state or local guidelines for cleaning requirements Overnight soaking with overdosed Chlorine may damage rubber part in basin CLEANING PROGEDURE IS REQUIRED BY STATE BOARDS Note A cleaning log should be kept with each pedicure spa Each State will have slight differences in cleaning policies please check with your state s Bureau of Barbering and Cosmetology or Regulatory Authority for specific details Safety Requirements for Pedicure Spas The Bureau of Barbering and Cosmetology requires that salons using whirlpool pedicure foot spas must follow these disinfecting procedures to ensure proper cleaning and maintenance of the equipment and to prevent the spread of bacterial or parasitic disease Violation of this section may result on an administrative fine and
15. ion of Sodium Hypochlorite of approximately 50ppm used according to manufacturer s instructions 2 The spa system shall be flushed with the bleach and water solution or Sodium Hypochlorite solution for 5 10 minutes and allowed to sit for 6 10 hours 3 The spa system shall be drained and flushed with water before use upon a patron 21 Version 1 3 06 13 2012 Pioneering Smart Pedi Spas LEXOR LIMITED FACTORY WARRANTY LIMITED COVERAGE All parts are solely repaired or replaced at Lexor s option any evaluated defects in workmanship except the strictly excluded conditions below Labor shipping and return shipping are not included Lexor reserves the rights to send out new or equivalent to new as replacements Lexor shall have no obligation to repair replace or refund until the verification process by Lexor is completed Lexor s limited warranty applies only to Lexor Pedicure Spas utilized in the United States This limited warranty is not transferrable Furthermore this limited warranty is void if removed from its place of initial shipment Spa Tub Shipping or return shipping cost of spa tub is not included in the limited warranty Pedicure Stool Manicure Stool and Customer Chair 1 Yr warranty on adjustable hydraulic and wheels from the date of shipment No warranty on Upholstery and any other parts not listed TERRA BELLA FURNITURE WARRANTY Claims of damages or any missing parts must be made within 48 hrs business day a
16. nch circuit outlet protected by a Class A GROUND FAULT CIRCUIT INTERRUPTER GFCI and the GFCI shall be tested regularly for continued protection and correct operation If a Class A GFCI protected outlet is not available DO NOT USE THIS PRODUCT Please contact a licensed electrician for installation of a Class A GFCI according to local electric codes or equivalent A Warning DO NOT USE if you are diabetic have poor circulation or if any area of your feet or legs is inflamed or has an open sore Consult your physician before using if you have any kind of fungal infection swelling fracture or persistent pain ZN Warning TO REDUCE RISK OF INJURY DO NOT PERMIT CHILDREN TO USE THIS UNIT UNLESS THEY ARE CLOSELY SUPPERVISED AT ALL TIME e LIRE LES INSTRUCTION DU FABRICANT AVANT DE METTRE EN MARCHE e UTILISER SEULEMENT A L INTERIEUR e COUPER LE COURANT AVANT DE PROCEDRE AU DEPANNAGE AU NETTOYAGE AN Warning Excessive water temperature is dangerous and should be checked BEFORE use Maximum temperature of the water should never exceed 100 degrees F DO NOT STEP STAND IN FOOT BASIN Always enter and exit the Pedicure Spa slowly and carefully NEVER bring and or operate any electrical devices into or near the Pedicure Spa Maximum load in spa chair is 250lbs 114kg Pedicure Spa Chairs are not recommended for use on carpet or wood floors AN Warning If a crack in the GLASS BOWL occurs DO NOT handle unless the proper attire
17. nical switch located on the left side of the front panel When activating the switch it will raise the drain stopper and power up the drain pump if exist at the same time Two 2 Drain Sensors are located at bottom of basin which need to be cleaned frequently as needed to ensure proper operation 1 To drain water Turn the drain knob clockwise Drain pump is activated and will turn off automatically when water is empty 2 To turnoff the drain pump Turn the drain knob counterclockwise any time CAUTION Reset the Drain knob to vertical position to close the drain stopper prior starting Auto Fill 15 Operation and Care DAS Front Panel Functional amp Operating Instructions DIGITAL AUTOMATED FUNCTION R Lexor 1 Auto Fill Press to turn water on or off Water will fill up to reach the sensor level and activate the whirlpool jet The switch can be activated to turn on or turn off water any time during the Auto Fill M cycle EXCEPT when water is at sensor level 2 PureFlo Press to turn Jet on or off any time during this auto cycle Caution Jet will not be activated if water level is low Press the jet button to resume water fill up and start the whirlpool jet 3 L E D light LED light will be automatically turn on amp off followed the whirlpool jet action Press to turn LED Strip light on and stay on at all time This option can be activated only when the system is off 4 Seat Adjustment Backward
18. pe Plumbing Flow Pattern for Power Drain Plumbing Flow Pattern Power Draln Hot cold water Inlet Back Flow Preventer Not Included Optional as required by Local City Plumbing Code see detall A U Check Valve 1 2 included All Drain Piping from Check Valve to wall and behind wall not included detall A To be connected to an Indirect Waste Connector Loca plumbing is responsible from check valve to wall for wastewater treatment system according to Local Plumbing Code Installation Plumbing Flow Pattern for Gravity Drain Plumbing Flow Pattern Gravity Drain Hot cold water Inlet Back Flow Preventer Not Included z Optlonal as required by Local Clty Plumbing Code 1 1 4 Flex Hose w Removable Connection Under ground Local plumbing is responsible for underground wastewater treatment system according to Local Plumbing Code HOT AND COLD WATER SUPPLY LINES Carefully connect 7 ID supply hoses not provided to fresh water sources Shut off valves not provided should be utilized Valves should be placed outside the tub for easy access Before water line connections please follow below Determine if your spa chair is used for a new construction of a salon or a replacement spa chair 1 New construction Make sure to remove any and all debris and or dust from current hot cold water pipes before hooking up to spa Suggested direction to remove debris turn on water and drain into a bucket or
19. to Drain with D A S Models Auto fill can be operated by either Auto fill Jet Knob or Digital Automated System DAS 1 1 Use faucet knob to adjust optimal water temperature at H or C directory 1 2 Pull out and tilt down faucet knob to shut off water any time during the automatic or manual CAUTION Faucet Knob must be used to shut off water supply to basin when spa chair is left unattended and overnight Water Control Knob Pull out knob in direction of arrow Tilt down knob to shut off water Drain Knob ___ D __ Auto Fill Jet Knob Water Control Knob Hot Cold Auto Fill Jet Switch Dual functional momentary switch located on the right side of the front panel 1 To turnwater on Turn knob clockwise for 1 second and release Water will fill up to reach the sensor level and activate the whirlpool jet 2 To turn water off Turn knob clockwise for 1 second and release to turn off water The switch can be activated to turn on or turn off water any time during the Auto Fill cycle EXCEPT when water is at sensor level ta Activating this Auto Fill Jet Knob When Pure Flo whirlpool Jet is running system will resume with turn off Jet i When water is full and Jet is off system will resume with filling up water for 3 seconds and Jet turns on 3 When water level is low system will resume with filling up water prior to activating whirlpool jet Drain Switch Dual Action Electro mecha
Download Pdf Manuals
Related Search