The MSE-L22 Instructions
Contents
1. MAGNIDIGHI EXPLSRER lassic MSE L22 User s Manual Table of Contents SECTION 1 Unpacking and Set Up of System 2 SECTION 2 Features and Operating Instructions 4 Turning ON the SyStem ccccsccceeeseeeeeeeseeeeneeeeseneoneseneoneeeesens 4 Selecting Viewing MOE cccceseceeeeseeeeseneceeseneeeeeeeseneeeesenees 4 Adjusting d Eier d ef Le EE 5 e OO Ed ien ee ing E 6 Using the Viewing Table esse 7 SECTION 3 Service and Safety Information 8 FCC Information Explorer CCTV s has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in its installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications If this equipment does cause harmful interference the user will be required to correct the interference hdm 1a Section 1 Unpacking amp Set Up 1 Remove User s Manual and power cord from top foam compartments and remove the upper foam packaging IMPORTANT DO NOT DISCARD packing carton and materials In t2. that the Viewing Table remain steady or locked The Table is equipped with a Brake Lever to Lock the movement of the table The Lever is located below the front edge of the table as shown Brake em Tei Lock e Moving the lever all the way to the RIGHT locks the table e Releasing the back to the CENTER position restores full table movement front to back and side to side Additional Table Features Include 1 Rear Alignment Edge on the table allows you to line up pages or envelopes This is especially useful for writing 2 Non glare wipeable table surface reduces eyestrain Its dark color and speckled pattern helps you to distinguish the edge of a white page Section 3 Safety amp Service Safety Information and Maintenance 1 ALWAYS put the Viewing Table in the LOCKED position Brake Lever to the far right and use the hand holds in the base of the unit when attempting to move the machine 2 Place unit on a sturdy table away from any heat source DO NOT place your unit on an unstable table cart or stand Doing so may allow the unit to fall causing serious damage to the unit or bodily injury 3 Use of a surge protected power strip is recommended to protect your unit from power outages etc 4 Avoid putting your hands and fingers into any opening touching the camera lens or mirror in the camera housing could reduce image quality 5 Dust the screen as needed with a soft dry cloth 6 Making sure that th
3. ble to the Monitor Jack on the rear panel of the camera Section 2 Features amp Instructions Turning ON the System Turn the unit ON using the Power Switch located on the right side of control panel of the camera housing The lighting should illuminate the Viewing Table If the Lights do not illuminate and the screen does not turn on please check the power cord connections described in the previous section POWER Switch Contrast Size MAGNI CGHT 8 EXPLSRER The screen should come on after a normal delay of several seconds If the screen does not turn ON after a few seconds press the Monitor Power button located in the lower right corner of the Monitor below the screen The Monitor settings are set at the recommended settings so there is not need to adjust the monitor settings Place reading material or your hand under the camera to confirm the video image displays on the monitor Selecting Viewing Mode Located on the Camera Control Panel the Mode Switch allows a choice of Full Color viewing along with selected Black amp White and Reversed Black amp White combinations for optimal viewing based on your unique vision needs o Selecting Viewing Mode cont d By pushing the MODE Control Switch UP or DOWN you cycle through the viewing modes In most cases the Full Color mode works well for viewing pictures or color graphics while one of the Black amp White or modes may perform better for readin
4. e unit is powered OFF use a slightly damp cloth to clean the unit s surfaces Do NOT spray chemicals or cleaning liquids directly on the unit Service Information Your Unit CONTAINS NO USER SERVICEABLE PARTS ALL SERVICE MUST BE DONE BY THE FACTORY OR AN AUTHORIZED SERVICE CENTER where available In the event of malfunctions or questions please contact us MagniSight Inc Call 800 753 4767 or 719 578 8893 Service Information cont d In the event Service is required you may be asked to send the unit to MagniSight s main repair facility The camera or system MUST BE SHIPPED IN THE ORIGINAL PACKAGING to prevent damage Please call MagniSight for return information or to order packaging if needed NOTES
5. g or writing text Once you have selected your preferred viewing mode you should adjust the SIZE and CONTRAST controls for ideal viewing MODE Switch Power MAGNI SIGHT e i EXPLSRER Contrast Size Adjusting Magnification Magnification or SIZE of the image being viewed is e by turning the turning the Size Control SIZE Control Power Contrast MAGNI SIGHT E EXPLSRER e Turn the SIZE Control to the RIGHT to make image LARGER e Turn to the LEFT to make image SMALLER Adjusting Magnification cont d When first learning to use the camera system place printed Je material on the Viewing Table and adjust the Size Control to the smallest magnification setting Then begin turning the Size Control to increase the size of the image until you are able to read the text Adjusting Contrast The Contrast Control is used to BRIGHTEN or DARKEN the image being viewed Contrast can be readjusted whenever needed in any mode net Control Size Power MAGNI SIGHT EXPLSRER Turn the CONTRAST Control to the RIGHT to brighten the image e Turn to the LEFT to darken Using the Viewing Table The Viewing Table sometimes referred to an X Y Table is mounted on a slide mechanism allowing it to move under the camera left to right and also front to back This assists you in moving the material you are viewing under the camera Depending on what is being viewed sometimes users prefer
6. he event service or return of the unit is required in the future the original packaging is REQUIRED to insure no damage occurs in shipping Recommend 2 Person Lift For Next Step 2 Next firmly grab hold of each side of camera unit and lift unit out of the foam packing in the bottom of the carton Place Camera System on sturdy desk or table where it will be used Avoid places near any heat source or direct sunlight Position the Camera unit on the desk surface to your preferred location The bottom of the unit is equipped with rubber pads to protect the table surface and to prevent the unit from sliding 3 Next remove packaging from around the Camera and Monitor and place packing materials back in the original carton DO NOT DISCARD PACKAGING MATERIALS See Note Above 4 Connect the AC Power Cord to the AC IN jack on the rear panel of the camera Plug the other end of the AC Power Cord into wall outlet or surge protected power strip not included See Hook Up Picture on next page Set Up cont d Monitor DVI Signal Cable CAUTION THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE ENSURE THAT THE SOCKET OUTLET IS LOCATED NEAR THE EQUIPMENT AND IS EASILY ACCESSIBLE 5 Next connect the Monitor Power Cord to the AC OUT jack on the rear panel of the camera Note the power supplied to the AC OUT jack turns on amp off with the camera power switch 6 Finally connect the monitor signal ca
Download Pdf Manuals
Related Search